Results for “dynamic load model” — Page 16

NASA NTRS2003

Mode Jumping of an Isogrid Panel Under Quasi-Static Compression

A wide column test of a composite isogrid panel subjected to quasi-static, axial compression is modeled with a hybrid-static dynamic computational method. The data from the test panel exhibited discontinuous responses in the compressive load for slowly increased end-shortening. The computational model was developed to corroborate these discontinuities with the phenomenon of mode jumping. Mode jumping refers to the transient response of the panel from an unstable bifurcation point on a postbuckled equilibrium path to a second stable equilibrium state on a new equilibrium path. On the new equilibrium path, both the analysis and test show that the panel can resist increased endshortening beyond that of the unstable critical point. Fair agreement is achieved between the analysis and test.

Muheim, Danniella M.↗

NASA NTRS1997

Test Verification of the Cassini Spacecraft Dynamic Model

The Cassini spacecraft mission to Saturn will be launched in October 1997, on a Titan IV/Centaur launch vehicle. Cassini is the largest interplanetary spacecraft ever developed. Before launch approval can be obtained, a test verified finite element model of the Cassini spacecraft must be completed and approved by NASA. The correctness of this model is critical to the final verification coupled loads analysis and margin of safety assessments.

Cassini↗

NASA NTRS2013

Development of an Aeroelastic Modeling Capability for Transient Nozzle Side Load Analysis

Lateral nozzle forces are known to cause severe structural damage to any new rocket engine in development during test. While three-dimensional, transient, turbulent, chemically reacting computational fluid dynamics methodology has been demonstrated to capture major side load physics with rigid nozzles, hot-fire tests often show nozzle structure deformation during major side load events, leading to structural damages if structural strengthening measures were not taken. The modeling picture is incomplete without the capability to address the two-way responses between the structure and fluid. The objective of this study is to develop a coupled aeroelastic modeling capability by implementing the necessary structural dynamics component into an anchored computational fluid dynamics methodology. The computational fluid dynamics component is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, while the computational structural dynamics component is developed in the framework of modal analysis. Transient aeroelastic nozzle startup analyses of the Block I Space Shuttle Main Engine at sea level were performed. The computed results from the aeroelastic nozzle modeling are presented.

Wang, Ten-See↗

NASA NTRS2013

Development of an Aeroelastic Modeling Capability for Transient Nozzle Side Load Analysis

Lateral nozzle forces are known to cause severe structural damage to any new rocket engine in development during test. While three-dimensional, transient, turbulent, chemically reacting computational fluid dynamics methodology has been demonstrated to capture major side load physics with rigid nozzles, hot-fire tests often show nozzle structure deformation during major side load events, leading to structural damages if structural strengthening measures were not taken. The modeling picture is incomplete without the capability to address the two-way responses between the structure and fluid. The objective of this study is to develop a coupled aeroelastic modeling capability by implementing the necessary structural dynamics component into an anchored computational fluid dynamics methodology. The computational fluid dynamics component is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, while the computational structural dynamics component is developed in the framework of modal analysis. Transient aeroelastic nozzle startup analyses of the Block I Space Shuttle Main Engine at sea level were performed. The computed results from the aeroelastic nozzle modeling are presented.

Wang, Ten-See↗

NASA NTRS1990

Dynamical effects from equation of state on topographies and geoid anomalies due to internal loading

Using a Cartesian compressible model, the effects of compressibility on geoid anomalies and of deformations on the topographic signatures caused by internal loading in the mantle are quantitatively investigated by examining different types of the equation of state. Also considered are different types of density laws with variations of thermodynamical parameters taken into play. It is shown that surface topographies are not changed much by the effects of mantle compressibility and that the deformation of bottom boundary is not significantly influenced except for long wavelengths and large viscosity contrasts between the upper and lower mantles. On the other hand, mantle compressibility can greatly affect geoid signals with horizontal wavelengths exceeding 10,000 km.

Hong, Hanjing↗

NASA NTRSDate not supplied

Artemis I Prelaunch Flight Readiness Analysis

The Prelaunch loads analysis traditionally captures the vehicle and Mobile Launcher (ML) loads associated with stacking in the Vehicle Assembly Building (VAB), rollout to the pad, and high-speed winds while out on the pad prior to liftoff. The following paper details the methodology used in this analysis for loads for the Artemis Flight Readiness assessment. This paper focuses on the stacking and assembly loads, the loads induced by fueling, and the load seen during rollout to the pad. Methods for integrating multiple structural models in dynamic simulations using interface forces, constraint modes, and residual vectors is discussed. Both linear and nonlinear responses are addressed. Simulation results are compared to measured data from the Dynamic Rollout Test (DRT) and Wet Dress Rehearsal (WDR).

SLS↗

NASA NTRS1994

Dynamic Load Balancing for Computational Plasticity on Parallel Computers

The simulation of the computational plasticity on a complex structure remains a formidable computational task, especially when a highly nonlinear, complex material model was used. It appears that the computational requirements for a such problem can only be satisfied by massively parallel architectures. In order to effectively harness the tremendous computational power provided by such architectures, it is imperative to investigate and to study the algorithmic and implementation issues pertaining to dynamic load balancing for computational plasticity on a highly parallel, distributed-memory, multiple-instruction, multiple-data computers. This paper will measure the effectiveness of the algorithms developed in handling the dynamic load balancing.

Pramono, Eddy↗

NASA NTRS2001

Evaluation of New Actuators in a Buffet Loads Environment

Ongoing research in buffet loads alleviation has provided an application for recently developed piezoelectric actuators capable of higher force output than previously existing actuators could provide and that can be embedded within the vehicle s structure. These new actuators, having interdigitated electrodes, promise increased performance over previous piezoelectric actuators that were tested on the fin of an F/A-18 aircraft. Two new actuators being considered by the United States Air Force to reduce buffet loads on high performance aircraft were embedded into the fins of an F/A-18 wind-tunnel model and tested in the Transonic Dynamics Tunnel at the NASA Langley Research Center. The purpose of this test program, called ENABLE (Evaluation of New Actuators in a Buffet Loads Environment), was to examine the performance of the new actuators in alleviating fin buffeting, leading to a systems -level study of a fin buffet loads alleviation system architecture being considered by the USAF, Boeing, and NASA for implementation on high performance aircraft. During this windtunnel test, the two actuators performed superbly in alleviating fin buffeting. Peak values of the power spectral density functions for tip acceleration were reduced by as much as 85%. RMS values of tip acceleration were reduced by as much as 40% while using less than 50% of the actuators capacity. Details of the wind-tunnel model and results of the wind-tunnel test are provided herein.

Moses, Robert W.↗

NASA NTRS1980

A comprehensive analytical model of rotorcraft aerodynamics and dynamics. Part 2: User's manual

The use of a computer program for a comprehensive analytical model of rotorcraft aerodynamics and dynamics is described. The program calculates the loads and motion of helicopter rotors and airframe. First the trim solution is obtained, then the flutter, flight dynamics, and/or transient behavior can be calculated. Either a new job can be initiated or further calculations can be performed for an old job.

Johnson, W.↗

NASA NTRS1987

Adaptive control strategies for cooperative dual-arm manipulators

Three strategies for adaptive control of cooperative dual-arm robots are discussed. Implementation of these adaptive controllers does not require the use of complex mathematical models of the arm dynamics or knowledge of the arm dynamic parameters or load parameters. These strategies have simple structures, and are computationally fast for on-line implementation with high sampling rates. In all three cases, the coupling effects between the arms through the load are treated as disturbances which are rejected by the adaptive controllers while following desired commands in a common frame of reference. Simulation results demonstrate the usefulness of the controllers.

Seraji, H.↗

NASA NTRS1990

Active control of structurally-coupled sound fields in elastic cylinders by vibrational force inputs

Active control of structurally-coupled sound fields in elastic cylinders is analytically and experimentally studied. The primary (noise) field in the cylinder model is generated by the coupled dynamic response of the shell under loading by a single exterior acoustic source. Control of the interior sound field is achieved by applying vibrational force inputs directly to the shell wall. Action of the point controllers serve to increase the input impedance of select structural modes of the shell which are well-coupled to the interior acoustic cavity, thus substantially reducing sound transmission into the cavity. Spatially-averaged noise reductions in excess of 30 dB are demonstrated for acoustic resonant conditions within the cavity. Twin controller configurations are presented which demonstrate the ability to independently control orthogonal modes of the interior acoustic space. Benefits and drawbacks of this new methodology for noise control are discussed and clearly demonstrated.

Jones, J. D.↗

NASA NTRS1991

Structural Integrity and Durability of Reusable Space Propulsion Systems

A two-day conference on the structural integrity and durability of reusable space propulsion systems was held on 14 to 15 May 1991 at the NASA Lewis Research Center. Presentations were made by industry, university, and government researchers organized into four sessions: (1) aerothermodynamic loads; (2) instrumentation; (3) fatigue, fracture, and constitutive modeling; and (4) structural dynamics. The principle objectives were to disseminate research results and future plans in each of four areas. This publication contains extended abstracts and the visual material presented during the conference. Particular emphasis is placed on the Space Shuttle Main Engine (SSME) and the SSME turbopump.

Source record↗

NASA NTRSDate not supplied

A Flexible Multibody Framework for Space Launch System Liftoff with Umbilical Separations

ICPSU clearances to the lifting SLS vehicle were computed utilizing a coupled system nonlinear simulation approach in order to accurately capture the impact of system flexibilities, SLS forcing functions, pad separation (twang), ML dynamics and timings • i.e., integrate ICPSU model into a SLS nonlinear Coupled Loads Analysis (CLA) This required utilizing a flexible multibody framework for the CLA and the integration of large displacements/rotations capabilities into that CLA • Gantry rotation • Disconnect and retraction of flexible hoses

Arya Majed↗

NASA NTRS2001

Transient Reliability Analysis Capability Developed for CARES/Life

The CARES/Life software developed at the NASA Glenn Research Center provides a general-purpose design tool that predicts the probability of the failure of a ceramic component as a function of its time in service. This award-winning software has been widely used by U.S. industry to establish the reliability and life of a brittle material (e.g., ceramic, intermetallic, and graphite) structures in a wide variety of 21st century applications.Present capabilities of the NASA CARES/Life code include probabilistic life prediction of ceramic components subjected to fast fracture, slow crack growth (stress corrosion), and cyclic fatigue failure modes. Currently, this code can compute the time-dependent reliability of ceramic structures subjected to simple time-dependent loading. For example, in slow crack growth failure conditions CARES/Life can handle sustained and linearly increasing time-dependent loads, whereas in cyclic fatigue applications various types of repetitive constant-amplitude loads can be accounted for. However, in real applications applied loads are rarely that simple but vary with time in more complex ways such as engine startup, shutdown, and dynamic and vibrational loads. In addition, when a given component is subjected to transient environmental and or thermal conditions, the material properties also vary with time. A methodology has now been developed to allow the CARES/Life computer code to perform reliability analysis of ceramic components undergoing transient thermal and mechanical loading. This means that CARES/Life will be able to analyze finite element models of ceramic components that simulate dynamic engine operating conditions. The methodology developed is generalized to account for material property variation (on strength distribution and fatigue) as a function of temperature. This allows CARES/Life to analyze components undergoing rapid temperature change in other words, components undergoing thermal shock. In addition, the capability has been developed to perform reliability analysis for components that undergo proof testing involving transient loads. This methodology was developed for environmentally assisted crack growth (crack growth as a function of time and loading), but it will be extended to account for cyclic fatigue (crack growth as a function of load cycles) as well.

Nemeth, Noel N.↗

NASA NTRS2002

Further Examination of the Vibratory Loads Reduction Results from the NASA/ARMY/MIT Active Twist Rotor Test

The vibration reduction capabilities of a model rotor system utilizing controlled, strain-induced blade twisting are examined. The model rotor blades, which utilize piezoelectric active fiber composite actuators, were tested in the NASA Langley Transonic Dynamics Tunnel using open-loop control to determine the effect of active-twist on rotor vibratory loads. The results of this testing have been encouraging, and have demonstrated that active-twist rotor designs offer the potential for significant load reductions in future helicopter rotor systems. Active twist control was found to use less than 1% of the power necessary to operate the rotor system and had a pronounced effect on both rotating- and fixed-system loads, offering reductions in individual harmonic loads of up to 100%. A review of the vibration reduction results obtained is presented, which includes a limited set of comparisons with results generated using the second-generation version of the Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD II) rotorcraft comprehensive analysis.

Wilbur, Matthew L.↗

NASA NTRS1996

Solar Dynamic Power System Stability Analysis and Control

The objective of this research is to conduct dynamic analysis, control design, and control performance test of solar power system. Solar power system consists of generation system and distribution network system. A bench mark system is used in this research, which includes a generator with excitation system and governor, an ac/dc converter, six DDCU's and forty-eight loads. A detailed model is used for modeling generator. Excitation system is represented by a third order model. DDCU is represented by a seventh order system. The load is modeled by the combination of constant power and constant impedance. Eigen-analysis and eigen-sensitivity analysis are used for system dynamic analysis. The effects of excitation system, governor, ac/dc converter control, and the type of load on system stability are discussed. In order to improve system transient stability, nonlinear ac/dc converter control is introduced. The direct linearization method is used for control design. The dynamic analysis results show that these controls affect system stability in different ways. The parameter coordination of controllers are recommended based on the dynamic analysis. It is concluded from the present studies that system stability is improved by the coordination of control parameters and the nonlinear ac/dc converter control stabilize system oscillation caused by the load change and system fault efficiently.

Momoh, James A.↗

NASA NTRSDate not supplied

The Flight Dynamics Risk Assessment of Artemis I

With launch vehicles and spacecraft, it is necessary to dynamically test the structure to validate structural models. These validated models are then used to determine a launch vehicle's control stability margin and the loads on the structure. While often a dedicated structural test article is used to correlate the integrated structure in preparation for the final analysis cycles, the Artemis I flight is using an approach where the components of the launch vehicle are dynamically tested and the component models validated. The fully integrated vehicle is not tested until a few months before launch, which limits the ability to fully correlate a model prior to launch. This paper introduces the Flight Dynamics Risk Assessment of the vehicle, which is the process being used to determine the adequacy of the vehicle structural model after the Integrated Modal Test. This work outlines the process of quickly tuning a model post-test then determining any control margin violations and increases in loads due to that tuned model.

Eric C Stewart↗

NASA NTRSDate not supplied

The Flight Dynamics Risk Assessment of Artemis I

With launch vehicles and spacecraft, it is necessary to dynamically test the structure to validate structural models. These validated models are then used to determine a launch vehicle's control stability margin and the loads on the structure. While often a dedicated structural test article is used to correlate the integrated structure in preparation for the final analysis cycles, the Artemis I flight is using an approach where the components of the launch vehicle are dynamically tested and the component models validated. The fully integrated vehicle is not tested until a few months before launch, which limits the ability to fully correlate a model prior to launch. This paper introduces the Flight Dynamics Risk Assessment of the vehicle, which is the process being used to determine the adequacy of the vehicle structural model after the Integrated Modal Test. This work outlines the process of quickly tuning a model post-test then determining any control margin violations and increases in loads due to the tuning of the model.

Eric C Stewart↗