Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Highly efficient bifacial single-junction perovskite solar cells

Bifacial photovoltaics (PV) harvest solar irradiance from both their front and rear surfaces, boosting energy conversion efficiency to maximize their electrical power production. For single-junction perovskite solar cells (PSCs), the performance of bifacial configurations is still far behind that of their state-of-the-art monofacial counterparts. Here, in this paper, we report on highly efficient, bifacial, single-junction PSCs based on the p-i-n (or inverted) architecture. We used optical and electrical modeling to design a transparent conducting rear electrode for bifacial PSCs to enable optimized efficiency under a variety of albedo illumination conditions. The bifaciality of the PSCs was about 91%–93%. Under concurrent bifacial measurement conditions, we obtained equivalent, stabilized bifacial power output densities of 26.9, 28.5, and 30.1 mW/cm 2 under albedos of 0.2, 0.3, and 0.5, respectively. We further showed that bifacial perovskite PV technology has the potential to outperform its monofacial counterparts with higher energy yields and lower levelized cost of energy (LCOE).

14 SOLAR ENERGY↗
DOE OSTI2024

Molecular Precision Engineering for Efficient Binary Organic Photovoltaics through Energy Level and Fibrillar Structure Modulation

Adjusting the energy levels and fibrillar morphology is paramount to enhancing the power conversion efficiency (PCE) of organic solar cells (OSCs). In the present study, an increase in the open-circuit voltage (VOC) is facilitated through the elongation of the alkyl chain within AQx (namely AQx-8), aiming to decrease the free volume ratio (FVR). This reduction in FVR attenuates electron-phonon coupling, thereby augmenting emission efficiency and diminishing the non-radiative energy loss (ΔEnr). To further refine the energy levels and morphological characteristics, the external undecyl chain of AQx-8 is substituted with a shorter carbon chain and cyclohexane noted for its considerable steric hindrance (AQx-H). Additionally, this alteration significantly mitigates intermolecular aggregation, expands the bandgap, and elevates the lowest unoccupied molecular orbital (LUMO) energy level, culminating in an elevated VOC of 0.923 V in devices based on AQx-H. Morphological analysis reveals that blends based on AQx-H exhibit an enhanced multi-length-scale fibrillar structure, which is conducive to exciton dissociation and charge transport, thereby contributing to a high fill factor (FF) nearing 80%. Consequently, this study reports one of the highest binary PCEs documented, standing at 19.5% (with certification at 19.0%).

14 SOLAR ENERGY↗
DOE OSTI2022

Magnetically Coupled Broadband Dual Magnetic Mass/Spring Vibrational Energy Harvesting Design

Self-powering sensors and networks are a reality. The ability to extract ambient energy from the surroundings to power electronic devices has a profound impact on the realization of smart adaptable sensor networks. In this study, a magnetically coupled dual spring and magnet design has been investigated to improve the efficiency and performance bandwidth of vibration energy harvesting (VEH) sensors. Using numerical models based on traditional systems of coupled ordinary differential equations (ODE), an optimized design was developed and compared to experimental measurements. Numerical and empirical results show good agreement. Results show improvement in the bandwidth over an equivalent linear system and corresponding improvement in output power conversion efficiency. The increased bandwidth allows improved conversion sensitivity and enhanced power harvesting capabilities. This operational bandwidth coincides with the expected input spectrum for in situ applications.

42 ENGINEERING↗
DOE OSTI2022

Spinel Cu–Mn–Cr Oxide Nanoparticle-Pigmented Solar Selective Coatings Maintaining >94% Efficiency at 750 °C

High-temperature concentrating solar power (CSP) system is capable of harvesting and storing solar energy as heat towards cost-effective dispatchable solar electricity. Solar selective coating is a critical component to boost its efficiency by maximizing solar absorptance and minimizing thermal emittance losses. However, maintaining a high solar-thermal conversion efficiency >90% for long-term operation at ≥750 ºC remains a significant challenge. Herein, we report spray-coated spinel Cu-Mn-Cr oxide nanoparticle-pigmented solar selective coatings on Inconel tube sections maintaining ≥94% efficiency at 750 ºC and ≥92.5% at 800 ºC under 1000x solar concentration after 60 simulated day-night thermal cycles in air, each cycle comprising 12h at 750 ºC/800 ºC and 12h cooling to 25 ºC. The solar spectral selectivity is intrinsic to the band-to-band and d-d transitions of non-stoichiometric spinel Cu-Mn-Cr oxide nanoparticles. Furthermore, this feature offers a large fabrication tolerance in nanoparticle volume fraction and coating thickness, facilitating low-cost and scalable spray-coated high-efficiency solar selective absorbers for high-temperature CSP systems.

14 SOLAR ENERGY↗
DOE OSTI2024

Template-Assisted Growth of High-Quality α-Phase FAPbI 3 Crystals in Perovskite Solar Cells Using Thiol-Functionalized MoS 2 Nanosheets

Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite “black phase”—photoactive cubic α-FAPI—as the relatively bulky FA + cations tend to favor the thermodynamically stable nonphotoactive “yellow phase”. Here, in this study, we present a templated growth strategy employing thiol-functionalized MoS 2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS 2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS 2 -incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pseudo-bilayer architecture enables high-performance organic solar cells with enhanced exciton diffusion length

Solution-processed organic solar cells (OSCs) are a promising candidate for next-generation photovoltaic technologies. However, the short exciton diffusion length of the bulk heterojunction active layer in OSCs strongly hampers the full potential to be realized in these bulk heterojunction OSCs. Herein, we report high-performance OSCs with a pseudo-bilayer architecture, which possesses longer exciton diffusion length benefited from higher film crystallinity. This feature ensures the synergistic advantages of efficient exciton dissociation and charge transport in OSCs with pseudo-bilayer architecture, enabling a higher power conversion efficiency (17.42%) to be achieved compared to those with bulk heterojunction architecture (16.44%) due to higher short-circuit current density and fill factor. A certified efficiency of 16.31% is also achieved for the ternary OSC with a pseudo-bilayer active layer. Our results demonstrate the excellent potential for pseudo-bilayer architecture to be used for future OSC applications.

14 SOLAR ENERGY↗
DOE OSTI2023

Highly Efficient Bifacial Single Junction Perovskite Solar Cells

We report on efficient, single-junction bifacial perovskite solar cells (PSCs) that simultaneously exhibit high front-side-illumination power conversion efficiency (PCE) (over 22 %) and high bifaciality (over 91%), which represents a significant advancement for single junction bifacial PSC development. The bifacial PSCs exhibit substantial performance boost under concurrent front and rear illumination conditions. The stabilized power output goes up to 25.3 mW/cm 2 under albedos of 0.2, which is comparable to the state-of-the-art monofacial single-junction PSCs. Our work demonstrates the value and potential of bifacial single junction PSCs as an attractive direction for future scientific study and commercialization.

commercialization↗
DOE OSTI2022

Terpolymer Donor with Inside Alkyl Substituents on Thiophene π ‐Bridges toward Thiazolothiazole A 2 ‐Unit Enables 18.21% Efficiency of Polymer Solar Cells

Abstract PM6 is a widely used D–A copolymer donor in the polymer solar cells (PSCs). Incorporating second electron‐withdrawing (A 2 ) units into PM6 backbone by ternary D–A 1 –D–A 2 random copolymerization strategy is an effective approach to further improve its photovoltaic performance. Here, the authors synthesize the PM6‐based terpolymers by introducing thiazolothiazole as the A 2 units connecting with thiophene π‐bridges attaching alkyl substituent towards the A 2 unit (PMT‐CT) or towards D‐unit (PMT‐FT), and study the effect of the alkyl substituent position on the photovoltaic performance of them. Two terpolymers PMT‐FT‐10 and PMT‐CT‐10 are obtained by incorporating 10% A 2 units in the terpolymers. The film of PMT‐CT‐10 shows slightly up‐shifted highest occupied molecular orbital (HOMO) energy levels while better co‐planar structure than that of PMT‐FT‐10. Meanwhile, the PMT‐CT‐10:Y6 blend film exhibits better molecular packing properties, more proper phase separation and more balanced hole and electron mobilities, which are beneficial to more efficient exciton dissociation, efficient charge transport and weaker bimolecular recombination. Consequently, the PMT‐CT‐10 based PSCs obtain the highest power conversion efficiency of 18.21%. The results indicate that side chain position on the thiophene π‐bridges influence the device performance of the terpolymer donors, and PMT‐CT‐10 is a high efficiency polymer donor for the PSCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Enhancing Photostability of Sn-Pb Perovskite Solar Cells by an Alkylammonium Pseudo-Halogen Additive

High-performance tin-lead perovskite solar cells (PSCs) are needed for all-perovskite-tandem solar cells. However, iodide related fast photodegradation severely limits the operational stability of Sn-Pb perovskites despite the demonstrated high efficiency and thermal stability. Herein, this work employs an alkylammonium pseudo-halogen additive to enhance the power conversion efficiency (PCE) and photostability of methylammonium (MA)-free, Sn-Pb PSCs. Density functional theory (DFT) calculations reveal that the pseudo-halogen tetrafluoroborate (BF 4 - ) has strong binding capacity with metal ions (Sn 2+ /Pb 2+ ) in the Sn-Pb perovskite lattice, which lowers iodine vacancy formation. Upon combining BF 4 - with an octylammonium (OA + ) cation, the PCE of the device with a built-in light-scattering layer is boosted to 23.7%, which represents a new record for Sn-Pb PSCs. The improved efficiency benefits from the suppressed defect density. Under continuous 1 sun illumination, the OABF 4 embodied PSCs show slower generation of interstitial iodides and iodine, which greatly improves the device photostability under open-circuit condition. Moreover, the device based on OABF 4 retains 88% of the initial PCE for 1000 h under the maximum-power-point tracking (MPPT) without cooling.

14 SOLAR ENERGY↗
DOE OSTI2024

Identifying and Amplifying the Spontaneously Formed Photo‐Charge Contribution in Opaque and Semitransparent Organic Photovoltaics

Abstract Spontaneous photo‐charge (SP) generation within the non‐fullerene (NFA) bulk helps avoid exciton (EX) related loss as compared to the traditional heterojunction route in organic solar cells (OSCs). Unfortunately, the promising SP utilization attracts little attention at this time due to the lack of knowledge on its specific contribution to the photovoltaic performance and rational optimization in high‐efficiency devices. To fill the gap, the NFAs’ SP characteristics are related with their photocurrent loss and power conversion efficiency (PCE) in state‐of‐the‐art materials. Though higher SP population is good for efficient EX utilization, it simultaneously acts as an additional photo‐charge recombination channel. The former can be further enhanced by increasing the NFAs’ crystallinity with preferred lamellar growth, and the latter can be suppressed via electric doping. With the aid of the two‐step optimization strategy, the total photocurrent loss is reduced from 14.4% to 4.8%, accompanying with PCE increment from 16.9% to 18.5%. The SP utilization strategy is finally applied in the semitransparent OSCs (ST‐OSCs), due to its less heterojunction area sensitive photo‐charge generation characteristic. A light utilization efficiency (LUE) is then increased from 3.21% to 3.77%. The findings highlight the pursue of efficient SP utilization as a new design philosophy in future OSCs’ progresses.

Chemistry↗
DOE OSTI2024

Why Perovskite Thermal Stress is Unaffected by Thin Contact Layers

Metal halide perovskite photovoltaics have emerged as a high efficiency, low-cost alternative that can potentially rival or enhance conventional silicon technology. Despite exceptional initial power conversion efficiencies, achieving compliance with international standards and widespread adoption requires further enhancements to their operational stability. Notably, addressing mechanical strain and stress in brittle perovskites has emerged as a pivotal approach to mitigate chemical degradation and improve reliability during thermal cycling. Here, in this study, a popularized strain engineering strategy is investigated in which a high coefficient of thermal expansion (CTE) hole transport layer (i.e., PDCBT) is cast onto inorganic perovskite (CsPbI 2 Br) at 100 °C. Contrary to previously published results, the X-ray diffraction (XRD):Sin 2 ψ and substrate curvature measurement techniques show that the hole transport layer has no discernible impact on perovskite strain. The accuracy of the XRD:Sin 2 ψ method for measuring strain is highlighted in contrast to an analysis based on shifts of single XRD peaks which can be influenced by multiple artifacts. The findings in this study are in accordance with mechanics theory: thin layers are unable to induce significant strain changes in perovskite thin films as the force they apply is negligible compared to that applied by a thick and stiff substrate.

14 SOLAR ENERGY↗
DOE OSTI2026

Physicochemical evolution of uranium nitride kernel microstructure with varying carbon distribution for advanced TRISO fuel forms

Uranium nitride (UN) has emerged as a fuel candidate for advanced nuclear reactor concepts due to its superior uranium density, thermal conductivity, and high melting temperature. However, the fabrication route for converting UO 2 to UN is complex and difficult to standardize. Although the chemistry of this conversion process is well-studied, more insight into the physicochemical dynamics of this conversion using advanced characterization techniques can help further our understanding of this material system. This work leveraged thermogravimetric analysis (TGA), X-ray diffraction (XRD), and nondestructive 3D X-ray computed tomography (XCT) to characterize dynamic microstructural changes in the UO 2 → UCO → UN fabrication pathway for two kernels with a varying carbon distribution in the starting composition. TGA and XRD were used to quantify changes in the mass, density, and chemical composition of the two kernels, while three-dimensional image processing and segmentation of XCT data were used to quantify the volume, surface area, and spatial distribution of features within each kernel for multiple steps along the fabrication pathway. The analysis indicates distinct differences between the two kernels that are correlated to downstream conversion efficiency. In conclusion, this work is among the first to perform 3D quantification of physicochemical evolution during UN conversion, providing quantitative correlation between processing, properties, and expected fuel performance.

Nuclear fuel↗
DOE OSTI2023

Precise synthesis and photovoltaic properties of giant molecule acceptors

Series of giant molecule acceptors DY, TY and QY with two, three and four small molecule acceptor subunits are synthesized by a stepwise synthetic method and used for systematically investigating the influence of subunit numbers on the structure-property relationship from small molecule acceptor YDT to giant molecule acceptors and to polymerized small molecule acceptor PY-IT. Among these acceptors-based devices, the TY-based film shows proper donor/acceptor phase separation, higher charge transfer state yield and longer charge transfer state lifetime. Combining with the highest electron mobility, more efficient exciton dissociation and lower charge carrier recombination properties, the TY-based device exhibits the highest power conversion efficiency of 16.32%. These results indicate that the subunit number in these acceptors has significant influence on their photovoltaic properties. This stepwise synthetic method of giant molecule acceptors will be beneficial to diversify their structures and promote their applications in high-efficiency and stable organic solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Local ionic transport enables selective PGM-free bipolar membrane electrode assembly

Bipolar membranes in electrochemical CO 2 conversion cells enable different reaction environments in the CO 2 -reduction and O 2 -evolution compartments. Under ideal conditions, water-splitting in the bipolar membrane allows for platinum-group-metal-free anode materials and high CO 2 utilizations. In practice, however, even minor unwanted ion crossover limits stability to short time periods. Here we report the vital role of managing ionic species to improve CO 2 conversion efficiency while preventing acidification of the anodic compartment. Through transport modelling, we identify that an anion-exchange ionomer in the catalyst layer improves local bicarbonate availability and increasing the proton transference number in the bipolar membranes increases CO 2 regeneration and limits K + concentration in the cathode region. Through experiments, we show that a uniform local distribution of bicarbonate ions increases the accessibility of reverted CO 2 to the catalyst surface, improving Faradaic efficiency and limiting current densities by twofold. Using these insights, we demonstrate a fully platinum-group-metal-free bipolar membrane electrode assembly CO 2 conversion system exhibiting <1% CO 2 /cation crossover rates and 80-90% CO 2 -to-CO utilization efficiency over 150 h operation at 100 mA cm -2 without anolyte replenishment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Pressure and thermal annealing effects on the photoconversion efficiency of polymer solar cells

This paper presents the results of experimental and theoretical studies of the effects of pressure and thermal annealing on the photo-conversion efficiencies (PCEs) of polymer solar cells with active layers that consist of a mixture of poly(3-hexylthiophene-2,5-diyl) and fullerene derivative (6,6)-phenyl-C 61 -butyric acid methyl ester. The PCEs of the solar cells increased from ~2.3% (for the unannealed devices) to ~3.7% for devices annealed at ~150 °C. A further increase in thermal annealing temperatures (beyond 150 °C) resulted in lower PCEs. Further improvements in the PCEs (from ~3.7% to ~5.4%) were observed with pressure application between 0 and 8 MPa. However, a decrease in PCEs was observed for pressure application beyond 8 MPa. The improved performance associated with thermal annealing is attributed to changes in the active layer microstructure and texture, which also enhance the optical absorption, mobility, and lifetime of the optically excited charge carriers. The beneficial effects of applied pressure are attributed to the decreased interfacial surface contacts that are associated with pressure application. The implications of the results are then discussed for the design and fabrication of organic solar cells with improved PCEs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High‐Performance Fluorinated Fused‐Ring Electron Acceptor with 3D Stacking and Exciton/Charge Transport

Abstract A new fluorinated electron acceptor (FINIC) based on 6,6,12,12‐tetrakis(3‐fluoro‐4‐hexylphenyl)‐indacenobis(dithieno[3,2‐ b ;2 ′ ,3 ′ ‐ d ]thiophene) as the electron‐donating central core and 5,6‐difluoro‐3‐(1,1‐dicyanomethylene)‐1‐indanone as the electron‐deficient end groups is rationally designed and synthesized. FINIC shows similar absorption profile in dilute solution to the nonfluorinated analogue INIC. However, compared with INIC, FINIC film shows red‐shifted absorption, down‐shifted frontier molecular orbital energy levels, enhanced crystallinity, and more ordered molecular packing. Single‐crystal structure data show that FINIC molecules pack into closer 3D “network” motif through H‐bonding and π–π interaction, while INIC molecules pack into incompact “honeycomb” motif through only π–π stacking. Theoretical calculations reveal that FINIC has stronger electronic coupling and more molecular interactions than INIC. FINIC has higher electron mobilities in both horizontal and vertical directions than INIC. Moreover, FINIC and INIC support efficient 3D exciton transport. PBD‐SF/FINIC blend has a larger driving force for exciton splitting, more efficient charge transfer and photoinduced charge generation. Finally, the organic solar cells based on PBD‐SF/FINIC blend yield power conversion efficiency of 14.0%, far exceeding that of the PBD‐SF/INIC‐based devices (5.1%).

Dai, Shuixing↗
DOE OSTI2026

Resilience of High-Efficiency CdSeTe:As and CdSeTe:Cu Solar Cells to Proton Irradiation

Power generation in space is currently dominated by expensive III-V multi-junction photovoltaic (PV) devices and cheap crystalline silicon (c-Si) PV devices. Both of these technologies degrade rapidly in proton-radiation-rich space environments, such as the Van Allen belt. The present study of cadmium selenide telluride- (CdSeTe-) based PV devices exposed to 150-to-1500 keV proton irradiation with fluences up to 9 x 1013 cm-2 reveal a more radiation-hard alternative to III-V and c-Si PV technologies. We report on measurement and analysis of current density vs voltage (JV), external quantum efficiency (EQE), external radiative efficiency, and capacitance vs voltage (CV) characteristics. JV characteristics of As-doped CdSeTe devices show 80% remaining power conversion efficiency (PCE) relative to unexposed controls when exposed to 650 keV protons at a fluence of 1012 cm-2. Under these same irradiation conditions, Cu-doped CdSeTe devices demonstrate an even better 95% PCE retention compared with unirradiated control devices. Evidence of radiation-induced absorber p-type doping compensation is observed in the glass-side EQE at 0 V and CV characteristics of most of the irradiated CdSeTe:As devices, but clear compensation is evident only for the most heavily irradiated CdSeTe:Cu devices. Elevated blue-green photocurrent in the film-side 0 V EQE suggests a buried junction in the most heavily irradiated CdSeTe:As devices. Although CdSeTe:Cu devices are the more resilient of the CdSeTe structures, both CdSeTe-based technologies are radiation-hard when compared to c-Si and III-V multi-junction PV.

14 SOLAR ENERGY↗