Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compositeness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Spatial heterogeneity analyses of pore structure and mineral composition of Barnett Shale using X-ray scattering techniques

The spatial heterogeneity of pore structure and mineral composition at mu m to mm scales in mm to cm-sized shale samples complicates the laboratory measurements of porosity & pore size distribution and consequently reservoir quality evaluation. Traditional fluid invasion characterization methods typically take hours to days to get data and can only test relatively small samples (usually 2.54 cm diameter core plugs and mm-sized rock chips). Furthermore, the Xray scattering techniques at the Advanced Photon Source of the Argonne National Laboratory have the capability to non-destructively determine the pore structure and mineral composition of mm x mm area in a short time of seconds and to hold several to hundreds of mm 2 sized sample to conduct large area heterogeneity analysis in the short duration of hours. With the use of ultra-small angle X-ray scattering (USAXS), small-angle X-ray scattering (SAXS), and wide-angle X-ray scattering (WAXS), the porosity, surface area and pore size distribution of two Barnett Shale samples have been mapped out and the mineral compositions are determined qualitatively. Overall, the porosity and pore surface area of the Barnett Shale Sample A over a 36 cm2 area ranges from 1.70 % to 8.13 % and 8.87 m 2 /g to 40.2 m 2 /g respectively. The porosity and surface area of Sample B over a 24 cm 2 area varies from 3.15 % to 11.7 % and 18.3 m 2 /g to 60.2 m 2 /g. In Sample A, the mineral composition shows a shift from carbonate-rich to siliciclastic-rich over a distance of several millimeters. For Sample B, the mineral compositions are mainly siliciclastic and do not show an obvious lithological change. The direct observations of high spatial heterogeneity of pore structure and mineral composition in shale illustrate the utility of integrated X-ray scattering techniques to provide valuable insights into shale studies and reservoir evaluation.

58 GEOSCIENCES↗
DOE OSTI2020

PdAu/YSZ composite hydrogen separation membranes with enhanced stability in the presence of CO

The effects of gold composition on the tolerance of palladium-based composite membranes to CO exposure was studied under the presence of high CO concentrations. Membranes with PdAu compositions ranging up to 41% by mass were exposed to binary 50/50 H 2 /CO gas atmospheres and both hydrogen flux and purity were monitored over time. It was observed that the highest gold composition (41%) suffered no degradation in membrane performance in terms of permeate hydrogen purity and hydrogen permeation flux during the 48 h exposure. Furthermore, for lower gold compositions, X-ray diffraction patterns suggested that carbon entered the film and could be removed by exposure to a non-CO containing gas mixture over time. However, removal of the carbon adversely affected purity; interestingly, some of the purity decline could be reversed upon re-exposure to the CO gas mixture. It is hypothesized that carbon loading in the palladium films causes lattice expansion and may even fill pore defects, thus lowering leaks through the Pd films. Furthermore, this study suggests that a membrane exposed to a CO mixture should not be cycled between CO and non-CO environments, but rather run continuously for best performance. Additionally, the choice of Pd-alloy and metal composition should be considered in regard to its carbon solubility to best predict lifetime performance.

08 HYDROGEN↗
DOE OSTI2024

In-situ ionothermal synthesis of nanoporous carbon/oxide composites: A new key to functional separators for stable lithium-sulfur batteries

Lithium-sulfur batteries (LSBs) with high energy density are promising for energy storage. However, conventional polypropylene-based separator cannot avoid polysulfides shuttling which impedes the practical application of LSBs. Herein, an in-situ ionothermal synthesis strategy that concurrently applies ionic liquid as the solvent, template and high-yield carbon source is proposed for the facile preparation of nanoporous carbon/oxide composite separator modifiers. The composites exhibit features of high polarity, self doping, oxygen vacancy, heteroatom doping, abundant defects and high electronic conductivity. Theoretical and experimental studies suggest that the composites can efficiently trap and convert polysulfides for high-performance LSBs. Indeed, in the composite-modified LSBs with next-generation roll-to-roll dry-processed high-loading sulfur cathodes, enhanced performance is achieved, revealing the effectiveness of the composites as functional materials towards separator modification. Therefore, the proposed strategy and its delivered nanoporous composites exhibit excellent versatility and practicality for high-performance LSBs.

25 ENERGY STORAGE↗
DOE OSTI2025

Molecular Insights into Novel Struvite–Hydrogel Composites for Simultaneous Ammonia and Phosphate Removal

Struvite (NH 4 MgPO 4 ·6H 2 O) mineralization is an effective technique for removing ammonium and phosphate species from wastewater. However, its wider use faces obstacles because of the copresence of various pollutants in wastewater and the additional requirement for magnesium to achieve proper supersaturation conditions. To address these challenges, this study developed novel mineral–hydrogel composites that can remove ammonium and phosphate simultaneously via heterogeneous struvite and calcium phosphate (CaP) mineralization in hydrogel matrices. The composites include in situ formed struvite and CaP mineral seeds, decreasing the nucleation energy barrier of struvite and CaP formation and promoting their heterogeneous nucleation kinetics even under undersaturation conditions in bulk solution. The dual struvite and CaP seeded composites can simultaneously reduce the ammonium and total phosphate concentrations up to 60% (26.3 mg of N/g) and 91% (9.54 mg of P/g), respectively. Furthermore, the average particle sizes in composites were increased from 6.12 to 14.8 nm after wastewater treatment. Moreover, various ions commonly existing in wastewater did not significantly interfere with the removal of ammonium and phosphate. Thus, these new mineral–hydrogel composites can provide an innovative way to lower nutrient levels before discharge to streams. Moreover, encapsulating ammonium and phosphate in mineral-hydrogel composites enables their upcycling in agricultural or biorefinery applications.

Cations↗
DOE OSTI2022

Holistic Design Consideration of Metal–Organic Framework-Based Composite Membranes for Lithium–Sulfur Batteries

Metal–organic framework (MOF)-based membranes have received significant attention as separators for lithium–sulfur (Li–S) batteries because of their high porosities, well-defined and tailored structures, and other tunable features that are desirable for preventing the “shuttle effect” of soluble polysulfides. Because of the insulating nature of most MOFs, composite membranes are generally constructed by a combination of MOFs and electron-conductive materials. In this work, we examine the property–performance relation between MOF-based separators and Li–S batteries by systematically adjusting the electrical conductivity, thickness, and mass loading of the MOF-based composite. Beyond the commonly referenced trapping or blocking ability of MOFs toward polysulfides, we find that by fixing the thickness of the MOF-based composite coating layer (~40 μm) on a Celgard membrane, the electrical conductivity of the MOF composite layer is of paramount importance compared with the physical/ chemical trapping ability of polysulfides. However, the trapping ability of MOFs becomes indispensable when the thickness of the composite layer is small (e.g., ~20 μm), indicating the synergetic effects of the adsorption and conversion capabilities of the thin composite layer. Furthermore, this work suggests the importance of a holistic design consideration for a MOF-based membrane for long-life and high-energy-density Li–S batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Alginate–Sodium Sulfate Decahydrate Phase Change Composite with Extended Stability

Here, this study reports on the use of sodium alginate to effectively stabilize sodium sulfate decahydrate (Na 2 SO 4 ∙10H 2 O, SSD) based phase change material (PCM) for application as a thermal energy storage material. Alginate/SSD composite PCMs were prepared by blending SSD with different concentrations of alginate polymer. The resulting composite PCMs demonstrate high phase change enthalpy ~160 J/g and extended cycling stability compared to existing PCM composites. The analysis carried out by optical microscopy, X-ray scattering, and periodic density functional theory (DFT) calculations demonstrated that the stabilization effect was caused by the interplay between ionic and hydrogen bond interactions between the alginate and SSD. Additionally, the variation in mechanical properties of PCM composites with polymer concentrations made it possible to formulate a composite that maintains stable performance after 3D printing. The advanced properties make this composite a promising candidate for application as a thermal energy storage material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Elasticity-controlled jamming criticality in soft composite solids

Soft composite solids are made of inclusions dispersed within soft matrices. They are ubiquitous in nature and form the basis of many biological tissues. In the field of materials science, synthetic soft composites are promising candidates for building various engineering devices due to their highly programmable features. However, when the volume fraction of the inclusions increases, predicting the mechanical properties of these materials poses a significant challenge for the classical theories of composite mechanics. The difficulty arises from the inherently disordered, multi-scale interactions between the inclusions and the matrix. To address this challenge, we systematically investigated the mechanics of densely filled soft elastomers containing stiff microspheres. We experimentally demonstrate how the strain-stiffening response of the soft composites is governed by the critical scalings in the vicinity of a shear-jamming transition of the included particles. The proposed criticality framework quantitatively connects the overall mechanics of a soft composite with the elasticity of the matrix and the particles, and captures the diverse mechanical responses observed across a wide range of material parameters. The findings uncover a novel design paradigm of composite mechanics that relies on engineering the jamming properties of the embedded inclusions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Silicon carbide fiber composite receiver tubes manufactured by PIP process

The performance of SiC fiber composites made by a polymer infiltration and pyrolysis (PIP) process was investigated. Two types of tubular composites were manufactured using Hi-Nicalon and Nicalon-CG silicon carbide fibers infiltrated with SMP10 silicon carbide matrix. The fiber content in both composites was about 25 vol.% with an average density of 2.39 g/cc. The tubular SiC composites showed stable solar absorptance and emittance of 0.97 and 0.91, respectively, at 800 °C. The composites were thermally shocked at 900, 1000, and 1100 °C with a waterjet simulating raindrops. As a result, the hoop tensile strength of the composites revealed no loss of mechanical strength due to the thermal shock experiments up to 1100 °C.

14 SOLAR ENERGY↗
DOE OSTI2021

Bardeen-Cooper-Schrieffer pairing of composite fermions

Topological pairing of composite fermions has led to remarkable ideas, such as excitations obeying non-Abelian braid statistics and topological quantum computation. Here, we construct a p-wave paired Bardeen-Cooper-Schrieffer (BCS) wave function for composite fermions in the torus geometry, which is a convenient geometry for formulating momentum space pairing as well as for revealing the underlying composite-fermion Fermi sea. Following the standard BCS approach, we minimize the Coulomb interaction energy at half filling in the lowest and the second Landau levels, which correspond to filling factors ν = 1/2 and ν = 5/2 in GaAs quantum wells, by optimizing two variational parameters that are analogous to the gap and the Debye cut-off energy of the BCS theory. Our results show no evidence for pairing at ν = 1/2 but a clear evidence for pairing at ν = 5/2. To a good approximation, the highest overlap between the exact Coulomb ground state at ν = 5/2 and the BCS state is obtained for parameters that minimize the energy of the latter, thereby providing support for the physics of composite-fermion pairing as the mechanism for the 5/2 fractional quantum Hall effect. We discuss the issue of modular covariance of the composite-fermion BCS wave function, and calculate its Hall viscosity and pair correlation function. By similar methods, we look for but do not find an instability to s-wave pairing for a spin-singlet composite-fermion Fermi sea at half-filled lowest Landau level in a system where the Zeeman splitting has been set to zero.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Thermal properties of field-assisted-sintered SiCN–Y 2 O 3 composites

Polymer-derived amorphous SiCN has excellent high-temperature stability and properties. To reduce the shrinkage during pyrolysis and to improve the high-temperature oxidation resistance, Y 2 O 3 was added as a filler. In this study, polymer-derived SiCN–Y 2 O 3 composites were fabricated by mixing a polymeric precursor of SiCN with Y 2 O 3 submicron powders in different ratios. The mixtures were cross-linked and pyrolyzed in argon. SiCN–Y 2 O 3 composites were processed using field-assisted sintering technology at 1350°C for 5 min under vacuum. Dense SiCN–Y 2 O 3 composite pellets were successfully made with relative density higher than 98% and homogeneous microstructure. Due to low temperature and short time of the heat-treatment, the grain growth of Y 2 O 3 was substantially inhibited. The Y 2 O 3 grain size was ~1 μm after sintering. The composites’ heat capacity, thermal diffusivity, and thermal expansion coefficients were characterized as a function of temperature. The thermal conductivity of the composites ceramics decreased as the amount of amorphous SiCN increased and the coefficient of thermal expansion (CTE) of the composites increased with Y 2 O 3 content. However, the thermal conductivity and CTE did not follow the rule of mixture. This is likely due to the partial oxidation of SiCN and the resultant impurity phases such as Y 2 SiO 5 , Y 2 Si 2 O 7 , and Y 4.67 (SiO 4 ) 3 O.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shake loss intensities in x-ray photoelectron spectroscopy: Theory, experiment, and atomic composition accuracy for MgO and related compounds

The relative intensities of XPS core levels, scaled by their photoionization cross sections, are regularly used to determine sample atomic composition. Cross sections, however, give the intensity to all possible final states for the core ionizations, not just to the main peak. This includes all intrinsic satellite structure (shake states and, for open shell systems, the different ionic multiplets). In practice, for solids, this is usually experimentally impossible to determine accurately because such a satellite structure sits on the inelastically scattered electron background and cannot be easily separated. Therefore, usually, only the intensity of the main peak is used. This limits the ultimate possible accuracy of XPS composition determination. The purpose of the present paper is to examine the contributions that a theoretical analysis of losses of intensity can make to improve quantitation. For an MgO single crystal, we show that the correct stoichiometry of 1:1 can be recovered using the theoretical analysis of the experimental MgO peak ratio intensities. For materials with a sufficient bandgap for the XPS main peaks to be separated from the scattered background, the intensity of main peaks can often be accurately determined. Thus, if one uses theory to calculate that fraction of the total intensity lost from a main peak into all its satellite structure, the intensity of just main peaks could then be used to more accurately determine relative atom % composition. This work tests this approach using a single crystal MgO (50% Mg, 50% O) standard. Ab initio electronic structure theory of representative MgO clusters is used to determine Hartree–Fock wave functions for the ground state and final ionized states corresponding to the main Mg 2p and O1s XPS peaks of the oxide. The sudden approximation, SA, is used to determine the fractional losses from these main peaks to shake satellites, which is found to be greater for O1s than Mg2p. This results in predicted “apparent composition” for stoichiometric MgO of 55.2% Mg, 44.8% O instead of the true 50% Mg, 50% O. Equivalent theory for CaO results in a predicted apparent Ca value of 53.4%. Experimentally, using Mg2s or 2p intensity ratio to O1s, we find values between 52.2% and 56.0% Mg using two crystals and four different instrument electron pass energies. The average value of the measurements is 54.5% Mg when corrected for the presence of an adventitious carbon overlayer and slight surface hydroxide. Though this agreement with theory may be somewhat fortuitous, given the potential experimental errors, which are fully discussed, it is similar to that in our earlier study on LiF. We also present preliminary experimental data on Mg(OH) 2 and MgSO 4 , which show a similar trend of apparently higher than 50% Mg, but we have no theory values. We are not yet able to experimentally test for validation of the difference between apparent composition for MgO (55.2% Mg) and CaO (53.4% Ca), owing to significant carbonate formation at the surface of the single crystal CaO. Here, an important conclusion is that the theoretical determination of shake losses, obtained with ab initio wavefunctions and the SA, is likely to be a useful way to calibrate the accuracy and reliability of compositions obtained from XPS intensities and merits further study.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Integrated TBC/EBC for SiC Fiber Reinforced SiC Matrix Composites for Next Generation Gas Turbines (Final Report)

In this ambitious project, a significant challenge preventing widespread use of ceramic matrix composites in hot section components of gas power generating turbines was addressed. Hot section components made from SiC fiber reinforced SiC matrix composites (SiC/SiC composites), have the potential to achieve a combined cycle energy efficiency of above 65%. To achieve this efficiency, the temperature of the combustion gases on the turbine component surface is expected to reach as high as ~1700ºC (3100ºF). However, SiC/SiC composites suffer from volatilization at high temperature under high velocity steam environment – typical in a turbine hot chamber. This integrated collaborative project, between two research groups at Clemson University and a team of engineers and scientists at GE Gas Power, focused on design, fabrication and evaluation of a new graded environmental barrier coating. Using the excellent compositional tailorability of polymer derived ceramics (PDCs), we developed an integrated EBC/BC that smoothly transitions from bottom SiC/SiC bond interface to hermetic sesquioxide (Y 2 O 3 ) top surface. This smooth compositional transition avoided the sharp CTE mismatch at interfaces to greatly reduce the thermal stress. The developed EBC is compatible with and bonds well with the bond coat that GE uses. The top hermetic oxide surface ensures low oxygen transportation and volatilization rates under the high velocity steam environment. The graded microstructure with increasing sesquioxide concentration also decreases the amount of Si and C elements near the top hermetic sesquioxide layer. Coatings made using a process suitable for manufacturing – atmospheric plasma spraying was demonstrated. The microstructure of coatings made using this process were fully characterized. Finally, the performance of these coatings was investigated under the most demanding conditions for this application. Specifically, high temperature, high velocity steam exposure; thermal shock test; and thermal cycling tests. The graded coatings performed exceptionally well in all these tests. Specific suggestions for future development in this area have also been identified. In addition to the excellent technical progress, this project helped initiate a robust collaboration between the research groups at Clemson and GE Gas Power. It also provided a high-quality learning and mentoring opportunity for the three post-doctoral research associates and two UG students at Clemson University who worked on this project. All proposed tasks, sub-tasks were completed, and all milestones achieved.

03 NATURAL GAS↗
DOE OSTI2023

Subcomponent Validation of Composite Joints for the Marine Energy Advanced Materials Project

The Marine Energy Advanced Materials project is an ongoing multi-year, multi-lab project with the main goals of addressing barriers and uncertainties facing marine energy developers in adopting advanced materials for structural applications. NREL's goals of the project were to address subcomponents testing needs for marine energy materials, to improve understanding of design allowables at the full-scale and provide near net-scale static and fatigue data of composite subcomponents using materials applicable to the marine energy industry. In the long term, the test method development and data generated would be used to inform standards development. This report outlines perhaps one of the largest-scale studies conducted with regards to saltwater conditioning of various composite material subcomponents and their subsequent structural validation, specifically directed at the marine renewable energy industry. A variety of fiberglass composite panels with epoxy and vinyl ester epoxy resin systems were manufactured at Montana State University, which were then used to manufacture an array of different types of subcomponent test specimens at the National Renewable Energy Laboratory's Flatirons Campus. These subcomponents were in the form of T-bolt and double-ended-insert specimens, which were intended to represent bonded and mechanical bolted connections for thick composite laminates, metal-metal and composite lap shear specimens to evaluate adhesion of constituent materials, and adhesive beam-shear specimens as part of an effort to better evaluate the characteristics of thick adhesive bondlines. Overall, the materials used were fiberglass reinforced epoxy and vinyl ester matrix composites, epoxy and methacrylate adhesives, and 316 and 2507 stainless steels. Specimens were then conditioned in salt water at various temperatures and for various periods of time at Florida Atlantic University and Pacific Northwest National Laboratory. All specimens were then mechanically characterized and validated using various test methods under static and fatigue loading conditions at NREL's Structural Technology Laboratory. Throughout the conditioning and mechanical validation process, valuable experience was gained, which will help guide future test method development for marine energy materials. In many instances, the results indicated similar observations as to what had been observed during previous coupon scale characterization efforts that provided a vital understanding of the scale up process. However in some instances, unexpected phenomena were observed, such as interactions between the adhesives and 316 steel. Furthermore, some materials exhibited significant degradation due to the saltwater conditioning. Ultimately, this report provides a detailed summary of the specimens that were designed, the subcomponent test methods that were developed, and the results that were generated, which will serve as important guidance for marine renewable energy developers and researchers for future structural designs and validation.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

High-Speed Layup and Forming of Automotive Composite Components

This Project is focused on the design and manufacture of automotive components that meet functional and environmental requirements of an existing automotive application at a cost of ≤ $\$$11.00 per kilogram weight reduction. This project fosters the development of composite material technologies suitable for high volume automotive processes and run rates as well as industry workforce development with these technologies. Current automotive manufacturing involves utilizing steel or aluminum in sheet form which is rapidly stamped into components at rates up to 3600 per hour. The metallic sheets are available in many different thicknesses, strength levels, and manufacturing rates are reasonable independent of part size. While composite materials are available for use in automotive applications, the material cost, labor to manufacture and the processing of the waste far exceed the cost compared to metallic designs. Typical composite layer by layer layup procedures don’t meet the desired 60 second layup time that current automotive processes require and are also restricted by part size. Due to these factors, composites have not yet made advances into today’s high volume automotive applications. Industry partners DURA, BASF, Ford, and IACMI core innovation partner MSU collaborated to develop a manufacturing process technology that is capable of manufacturing composite blanks at high volume and independent of part size. IACMI core innovation partner Purdue provided FEA analysis and cost modelling. The objective of this project was to demonstrate a composite sheet layup and consolidation process that can be commercialized for high volume requirements, identify potential layup equipment suppliers, and develop a process of 60 second layup, forming, and trimming of a continuous fiber automotive component for the mainstream market.

42 ENGINEERING↗
DOE OSTI2023

Hot Isostatic Pressing Control of Tungsten-Based Composites

Metal-oxide composites are commonly used in high temperature environments for their thermal stability and high melting points. Commonly employed with refractory oxides or carbides such as ZrC and HfC, these materials may be improved with the use of a low density, high melting point ceramic such as CeO2. In this work, the consolidation of W-CeO2 metal matrix composites in the high CeO2 concentration regime is explored. The CeO2 concentrations of 50, 33, and 25 wt.%, the CeO2 particle size from nanometer to micrometer, and various hot isostatic pressing temperatures are investigated. Decreasing the CeO2 concentration is observed to increase the composite density and increase the Vickers hardness. The CeO2 oxidation state is observed to be a combination of Ce3+ and Ce4+, which is hypothesized to contribute to the porosity of the composites. The hardness of the metal-oxide composite can be improved more than 2.5 times compared to pure W processed by the same route. This work offers processing guidelines for further consolation of oxide-doped W composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hardness Measurements and Interface Behavior of SiC-B 4 C-Si Multiple Phase Particulate Composites Made with Melt Infiltration and Additive Manufacturing

Reaction-bonded SiC-B 4 C-Si ceramic composites were binder jet 3D-printed and subsequently pressureless-melt-infiltrated with molten Si. The addition of B 4 C aided the Si infiltration to produce a highly dense composite. The microstructures and phases of these composites were examined. The measured hardness values of each constituent with Vickers and nanoindentation matched the bulk values, and the macro-hardness values with Knoop and spherical indentation represented the bulk, composite hardness values of all three phases together, which was close to a rule of mixtures value. For particulate-based composites, this is a significant finding. The interfacial bonds of SiC and Si were imaged using scanning transmission electron microscopy to view intimacy, whereas the crack propagation was examined with carefully placed indents. This work demonstrated that pressureless melt infiltration with a reactive particle provides a method to shape non-wetting reaction-bonded ceramic composites with limited shrinkage and high density and provides insights into the mechanical behavior with numerous indentation techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Multicontinuum-Theory-Based Approach to the Analysis of Fiber-Reinforced Polymer Composites with Degraded Stiffness and Strength Properties Due to Moisture Absorption

Marine energy generation technologies such as wave and tidal power have great potential in meeting the need for renewable energy in the years ahead. Yet, many challenges remain associated with marine-based systems because of the corrosive environment. Conventional materials like metals are subject to rapid corrosive breakdown, crippling the lifespan of structures in such environments. Fiber-reinforced polymer composites offer an appealing alternative in their strength and corrosion resistance, but can experience degradation of mechanical properties as a result of moisture absorption. An investigation is conducted to test the application of a technique for micromechanical analysis of composites, known as multicontinuum theory and demonstrated in past works, as a mechanism for predicting the effects of prolonged moisture absorption on the performance of fiber-reinforced composites. Experimental tensile tests are performed on composite coupons with and without prolonged exposure to a salt water solution to obtain stiffness and strength properties. Multicontinuum theory is applied in conjunction with micromechanical modeling to deduce the effects of moisture absorption on the behavior of constituent materials within the composites. The results are consistent with experimental observations when guided by known mechanisms and trends from previous studies, indicating multicontinuum theory as a potentially effective tool in predicting the long-term performance of composites in marine environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanoscale Three-Dimensional Imaging of Degradation in Composite Si-Containing Anodes

The use of silicon (Si) in next-generation lithium-ion battery (LIB) anodes has the potential to dramatically improve electrochemical performance over current LIB graphite (Gr) anodes, due to silicon’s higher specific capacity.1 However, widespread implementation of Si-containing anodes is inhibited by issues such as significant Si volume expansion during lithiation and an unstable solid-electrolyte interphase (SEI), resulting in unreliable performance and poor cycle life. Currently, composite anodes with both Si and graphite active materials are used to increase capacity and mitigate some of the limitations associated with Si. In composite electrodes with a heterogeneous distribution of components with varying electrical properties (including Si, Gr, conductive carbon additive, and binder), it is important to understand the local distribution of each component to correlate with electrochemical processes, particularly localized degradation and heterogeneous aging, and to optimize performance. To investigate Si-containing composite anodes in the nanoscale, we use scanning spreading resistance microscopy (SSRM), a form of scanning probe microscopy (SPM) that probes local electronic resistivity. By examining the intrinsic electronic resistivity contrast between the anode components, separate phases can be distinguished and understood within the composite structure.2 This work studies the effect of electrochemical cycling in two different electrolytes on component distribution and aging by comparing the electrical and structural evolution of composite Si-graphite electrodes and SEI before and after charge-discharge cycling. 1. W. J. Zhang. A review of the electrochemical performance of alloy anodes for lithium-ion batteries J. Power Sources 196 13–24 (2011). 2. C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C.-S. Jiang, M. Al-Jassim, D. Finegan, S.-D. Han and S. DeCaluwe: Three-Dimensional Mapping of Resistivity and Microstructure of Composite Electrodes for Lithium-Ion Batteries. ACS Nano Letters Accepted (2020).

ADVANCED PROPULSION SYSTEMS↗