Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The role of environmental conditions on the carbonation of an alkali-activated cementitious waste form

Cast Stone is a cementitious waste form being considered for the solidification of low activity waste at the DOE Hanford Site. Under near-surface disposal conditions in an arid environment, Cast Stone is subject to drying and carbonation which may impact retention of waste constituents. Here this study investigates the effects of environmental CO 2 concentration and relative humidity (RH) on the carbonation of Cast Stone. The rate of carbonation front ingress and the extent of carbonation reaction were characterized for samples aged up to 48 weeks at three RH levels and two CO 2 concentrations. While the 68% RH environment allowed the greatest reaction extent, the 15% RH environment yielded the deepest carbonation front ingress. At 68% RH, there was a linear relationship between the ingress rate and CO 2 concentration. Carbonation reactions increased the drying rate of Cast Stone. Redistribution of sodium toward the wetting front was observed under drying and carbonation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Optimization of edge bead removal (EBR) process to enhance defect reduction in optical lithography

Defect reduction remains a critical objective in the integrated circuit manufacturing process, particularly within the highly re-entrant lithography modules where minimizing defects is crucial. Defects at the wafer edge can contaminate lithography modules and downstream processing equipment, leading to redistribution onto the wafer surface and adversely affecting overall device yield. A persistent challenge in the resist coating process is the formation of resist edge beads, driven by the strong Van der Waals attraction of excess photoresist (PR) to itself and the underlying substrate. The edge bead removal (EBR) process is a standard cleaning step designed to eliminate these edge beads and prevent potential contamination. Here, in this study, we identify the sources of EBR induced defects and additional EBR process encroachment toward edge patterning during the EBR cleaning process. This study provides a comprehensive study aimed at optimizing the EBR cleaning process to effectively eliminate EBR-induced defects, thereby enhancing overall device yield. Specifically, we identify three primary defects induced by the EBR cleaning process: rainbow-type, finger-shaped, and teardrop-type defects. Our experimental study reveals that in addition to EBR rinse time, PR cast time is crucial parameters contributing to the formation of these defects. By properly optimizing the PR cast time and EBR rinse time, we were able to remove nearly 100 % of dense clusters of defects that were easily visible even at low magnification optical microscopy throughout the wafer edge. We observed that shorter PR casting times shows edge defects caused by inefficient EBR process because of insufficient time for PR to fully settle causing superfluous PR to continue flowing toward wafer edge during EBR clearing step, leading to partial removal of PR at the wafer edge and the formation of rainbow defects. Proper optimization of both PR casting time and EBR chemistries dispense time is essential to resolve these defects, ensuring efficient EBR cleaning process and improved overall device yield.

42 ENGINEERING↗
DOE OSTI2020

Freestanding self-assembled sulfonated pentablock terpolymer membranes for high flux pervaporation desalination

Pervaporation desalination has several advantages over competing desalination technologies, most notably an ability to select for or against volatile organic compounds and the ability to process high salinity feeds at a low transmembrane pressure. Pervaporation has not been commercialized for desalination applications because of its energy intensity. However, emerging processes such as hydraulic fracturing produce high total dissolved solids (>30-45 g/L) byproduct streams that exceed the operational limits of traditional reverse osmosis and could be treated by pervaporation. Here, we demonstrate free-standing pervaporation membranes with excellent permeance and high salt removal based on a partially sulfonated pentablock terpolymer with the tradename Nexar™. Pervaporation membranes were easily cast from this material with desalination performances comparable or superior to commercially available membranes. We found that the polymer degree of sulfonation and casting solvent polarity had a significant impact on the membranes’ water uptake but only a modest impact on the pervaporation desalination performance. Membranes with a degree of sulfonation of 52% (2.0 meq g –1 IEC) and a casting solution composed of 50 wt% n-propanol and 50 wt% toluene achieved a water flux of 3.32 kg m -2 h -1 (permeance 135 kg m -2 h -1 bar -1 ) with 99.5% salt removal in pervaporation from a 32 g/L –1 sodium chloride feed solution at room temperature. We demonstrated that dense, non-porous NexarTM pervaporation membrane permeance and salt separation performance were superior to commercial pervaporation membranes and equivalent to commercial membrane distillation membranes, which have much larger pores. Here, this study demonstrates that commercially available sulfonated pentablock terpolymers are excellent membranes for pervaporation desalination because of their ease of casting and excellent performance.

42 ENGINEERING↗
DOE OSTI2023

Assessing the influence of microstructure on uranium hydride size distributions via small angle neutron scattering

Here, the effect of microstructure on the internal hydriding behavior of both cast (1 mm grain size) and rolled (25 μm grain size) uranium containing hydrogen concentrations between 0 and 1.8 wppm were evaluated via small angle neutron scattering (SANS). Increasing hydrogen content up to 1.8 wppm in the cast uranium only weakly affected the average uranium hydride (UH 3 ) precipitate size, calculated from the SANS data. Conversely, the UH 3 phase fraction was found to strongly depend on the hydrogen content in the same cast samples. A substantially reduced UH 3 particle size distribution was observed in the rolled uranium relative to cast uranium containing the same nominal hydrogen content. It is hypothesized that the suppression of UH 3 formation in the rolled uranium is driven by increased hydrogen trapping at grain boundaries, and theoretical calculations that account for trap density, potency, and hydrogen diffusion kinetics support this hypothesis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Surrogate-assisted optimization under uncertainty for design for remanufacturing considering material price volatility

Remanufacturing is a well-established end-of-life (EOL) strategy that promises significant savings in energy and carbon emissions. However, the current design practices are not remanufacturing-inclusive, i.e., the majority of products are designed for a single life cycle. As a result, potential products that can sustain multiple life cycles are deprived of additional benefits of being designed for remanufacturing, such as reduced material usage, lower cost, and improved environmental impact. Moreover, the uncertainty in design, material selection, and economics are not considered to produce remanufacturable designs. Accordingly, this research proposes a design for remanufacturing (DfRem) framework that accounts for design uncertainty and material price volatility. The framework systematically explores the design space, performs design optimization under uncertainty, followed by topology optimization to provide additional mass savings, and finally, a price volatility analysis for plausible design material choices. The candidate designs are evaluated based on their design mass, material price volatility, failure mode characteristics, carbon footprint, and embodied energy impacts. The proposed framework's utility is demonstrated via the use of an engine cylinder head case study subjected to thermo-mechanical loads along with fatigue and wear failure. Considering grey cast iron and aluminum alloy as the design material choices, it was found that the cast iron design reduced the initial design mass by 6% as opposed to a 5% decrease for aluminum. On the other hand, about 8% area of the cast iron design failed due to fatigue, compared to 3% for aluminum. Here, we further observed that although the aluminum design provided better mechanical performance than the cast iron design, this material was more expensive and volatile in price.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In situ imaging of three dimensional freeze printing process using rapid x-ray synchrotron radiography

Three dimensional freeze printing (3DFP) combines the advantages of freeze casting and additive manufacturing to fabricate multifunctional aerogels. Freeze casting is a cost-effective, efficient, and versatile method capable of fabricating micro-scale porous structures inside the aerogels for many different applications. The 3DFP provided the capability of fabricating highly customized geometries with controlled microporous structures as well. However, there are still many unexplained phenomena and features because of the complexity of post-processes and indirect observation methods. This study demonstrates the design and construction of the in situ imaging systems, which use the x-ray synchrotron radiography to observe freeze casting and 3DFP processes. With the advantages provided by the in situ x-ray imaging techniques, the ice crystal growth with its unique lamellar structures can be observed during the freeze casting process. Here, the movement of freeze front, material deposition, and growth of ice crystals can also be visualized during the inkjet-based 3DFP process.

3D printing↗
DOE OSTI2021

Development of High Bs Fe-Ni Based Metal Amorphous Nanocomposite by Optimization of Glass Forming Ability

A growing interest in electric vehicles challenges soft magnetic materials to improve efficiency and power density. Metal amorphous nanocomposites (MANCs) have lower coercivities and eddy current losses, allowing for greater efficiency and higher switching frequency. The later allows for high motor speeds and improved power density. However, commercially available and laboratory demonstrated MANCs have shortcomings. Fe-based MANCs, such as FINEMET have excellent magnetic properties, but mechanical properties limit their application in high speed electric motors (HSMs). Fe-Co based MANCs, such as HITPERM, have high saturation inductions and good mechanical properties, but elevated magnetostrictive losses. Co-based MANCs and more recent Fe-Ni based MANCs have low losses and good mechanical properties, but lower saturation inductions (1-1.2 T), that limit power density in HSMs. Recently, much work has explored improving saturation induction in MANCs by increasing the content of magnetic elements, which comes at the cost of glass-forming ability (GFA). These efforts where generally limited to trial and error testing. Additionally, all work to date has focused on Fe-based alloys. In this work, a method of using Thermocalc simulation to locate near-eutectic compositions has been applied to Fe-Ni based alloys. Minima in liquidus temperature and solidification range were found for a ternary composition range and used to identify compositions that retain good GFA as the percentage of magnetic elements is increased. The (Fe 70 Ni 30 ) x (B-Si-Nb) 100-x alloy system for x=82% and x=85% was explored by Thermocalc simulations. This is an increase in magnetic element content compared to previously developed x=80% alloys. 3 compositions in the x=82% system, and 1 alloy in the x=85% system where identified and successfully cast as amorphous ribbon. The amorphous nature of the ribbon was confirmed by a bend test and XRD. Magnetic testing was performed by PPMS to measure saturation induction and Curie temperature of the amorphous material. The Curie temperatures increased to 407-438 °C for the x=82% alloys, and 462 °C for the x=85% alloy. Saturation induction increased to 1.28-1.36 T for the x=82% alloy and 1.48 T for the x=85% alloy, which is a significant improvement over the ~370 °C Curie temperature and 1.2 T saturation of previous Fe-Ni alloy. Crystallization behavior was studied by XRD for the x=85% alloy, showing that crystallization process follows a 2-step process of Amorphous → BCC+FCC+Amorphous → BCC+FCC+Fe 3 B+Fe 23 B 6 . Post annealing magnetic properties were studied by strip testing, and saturation induction as high as 1.48 T was seen after optimal annealing. TEM was used to study structure of as cast and annealed material. 2 alloys with x=82% compositions were identified with an optimal crystalline size of 10-20 nm, while the x=85% alloy had this structure in the as cast state. This opens the possibility of using the alloy in the as cast state, without requiring annealing. In conclusion, alloys with good GFA and improved magnetic properties were identified by Thermocalc simulation.

Krimer, Yuval↗
DOE OSTI2021

High Speed Hybrid Reluctance Motor Utilizing Anisotropic Materials

With high cost and volatility driving continued efforts to decrease reliance on the critical heavy rare earth materials used in traction drive applications, General Motors developed three variants of heavy rare earth-free (HRE-free) electric motors. The variants focused on taking advantage of advanced magnet technologies and new rotor topologies to improve mechanical strength and achieve power targets. The three variants were a HRE-free permanent magnet reluctance motor, a synchronous reluctance motor utilizing small HRE-free permanent magnets, and an induction motor with inserted copper bars and cast aluminum end-rings. Motors were designed with the intent of primary or secondary traction applications, depending on the topology. Variant 1 achieved performance comparable to HRE-containing permanent magnet motors through optimized topology and validation of HRE-free magnets, focusing on achieving energy products and demagnetization resistance comparable to those of HRE-containing magnets. Demagnetization testing demonstrated the motor robustness to currents and temperatures exceeding expected vehicle conditions, a key challenge to the use of HRE-free magnets. The Variant 1 motor also showed the best capability of meeting the US Drive technology 2020 targets, due to the high power-density of the permanent magnet motor and the potential cost reductions enabled by the removal of heavy rare earth materials. Variant 2 exhibited high efficiency in high speed regions due to the low high-speed losses, an important consideration for secondary traction applications, and significantly thrifted on magnet mass to reduce cost. Variant 3 contained copper bars within the induction rotor to reduce losses compared to cast aluminum, while using cast aluminum end-rings to reduce the cost and mass of the rotor. Optimization of the Cu-Al interface were focused on, as the interface is prone to forming brittle intermetallic compounds during the casting process. Prototypes of each motor variant were built and tested for performance, mechanical strength, and demagnetization resistance (Variants 1 and 2 only), with torque and power resulting close to the predicted values.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Affinity of LDR Organics to Cementitious Materials: Sorption and Leaching Tests

SRNL is working to identify and test the physiochemical interactions of organic contaminants of potential concern with minerals in grout/cementitious materials. Organic species may interact with cementitious minerals including slag, fly ash, cement, and other components/dopants like carbon in fly ash. The identification of such interactions will support the solidification process design, performance assessments for the chemicals of concern, and a proposed Resource Conservation and Recovery Act (RCRA) treatment variance specified for the Land Disposal Restriction (LDR) organics associated with Hanford tank waste. Inably expected to be present LDR organics associated with Hanford tank waste (RPP-RPT-63493, Rev 1a) was screened by functional groups, octanol-water partitioning coefficients, and detection frequency in Hanford tank waste samples. A subset of 10 compounds, spanning the identified properties, were tested using sorption and leachate tests. These compounds were subjected to traditional batch sorption tests and leaching tests on/from Cast Stone cementitious material with and without activated carbon (a potential organic adsorption additive). The interactions between organic compounds were observed in traditional batch sorption and modified Toxic Characteristic Leaching Procedure (TCLP) leachate tests for a surrogate Cast Stone material with and without an activated carbon addition. Specifically, phthalic acids (negatively charged) and 4-chloroaniline (polar) sorbed strongly to unmodified Cast Stone and a group of 3 phenolic compounds (2,4,6-Trichlorophenol, Pentachlorophenol, o-Cresol) were sorbed to and were retained by Cast Stone with a 1% activated carbon amendment.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Effect of Polyphenylsulfone and Polysulfone Incompatibility on the Structure and Performance of Blend Membranes for Ultrafiltration

This study deals with the modification of polyphenylsulfone ultrafiltration membranes by introduction of an incompatible polymer polysulfone to the polyphenylsulfone casting solution to improve the permeability. The correlation between properties of the blend polyphenylsulfone/polysulfone solutions and porous anisotropic membranes for ultrafiltration prepared from these solutions was revealed. The blend polyphenylsulfone/polysulfone solutions were investigated using a turbidity spectrum method, optical microscopy and measurements of dynamic viscosity and turbidity. The structure of the prepared blend flat sheet membranes was studied using scanning electron microscopy. Membrane separation performance was investigated in the process of ultrafiltration of human serum albumin buffered solutions. It was found that with the introduction of polysulfone to the polyphenylsulfone casting solution in N-methyl-2-pyrrolidone the size of supramolecular particles significantly increases with the maximum at (40–60):(60:40) polyphenylsulfone:polysulfone blend ratio from 76 nm to 196–354 nm. It was shown that polyphenylsulfone/polysulfone blend solutions, unlike the solutions of pristine polymers, are two-phase systems (emulsions) with the maximum droplet size and highest degree of polydispersity at polyphenylsulfone/polysulfone blend ratios (30–60):(70–40). Pure water flux of the blend membranes passes through a maximum in the region of the most heterogeneous structure of the casting solution, which is associated with the imposition of a polymer-polymer phase separation on the non-solvent induced phase separation upon membrane preparation. The application of polyphenylsulfone/polysulfone blends as membrane-forming polymers and polyethylene glycol (Mn = 400 g·mol -1 ) as a pore-forming agent to the casting solutions yields the formation of ultrafiltration membranes with high membrane pure water flux (270 L·m -2 ·h -1 at 0.1MPa) and human serum albumin rejection of 85%.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Micro-Structural Dispersity of SiMo Ductile Iron on High Temperature Performance during Static Oxidation

High silicon and molybdenum (SiMo) ductile iron is commonly used for car exhaust systems, and its micro-structural dispersity depends on intrinsic parameters, which include alloy composition and inoculation efficiency, as well as extrinsic factors, such as casting wall thickness and molding material, which define cooling rate during solidification. Micro-structural dispersity is referred to as the degree of heterogeneity of sizes of structural constituencies within the microstructure. A variation in the micro-structural dispersity could impact the high temperature performance of SiMo ductile iron during static oxidation and transient thermo-mechanical loading conditions. In this study, static high temperature tests were performed on SiMo ductile iron solidified in a casting with varying wall thicknesses from 5 mm to 100 mm. The faster solidified specimens (taken from near chilled casting surfaces) had extremely high micro-structural dispersity as compared to the thicker section samples. After thermal exposure, each of the samples were characterized using 2D sections and 3D µCT images, and the results indicated an order of magnitude difference in graphite phase dispersity. The surface degradation was quantified after static oxidation experiments were implemented at temperature intervals between 650 °C and 800 °C. Non-destructive µCT 3D analysis and SEM/EDS were performed on cross sections and used to quantify the scale topology and structure. Carbon analysis was used to decouple the scale formation and decarburization phenomena that occurred within the samples. These methods enabled the quantification of the oxidation of the SiMo cast iron with different micro-structural dispersity levels after being exposed to high temperature static oxidation. Additionally, the complex material behavior during oxidation-assisted transient thermo-mechanical loading will be presented in a separate article.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lightweight nodular iron crankshaft for heavy duty engine

An automobile vehicle crankshaft including a crankshaft casting of a nodular iron. The crankshaft casting includes multiple main journals coaxially aligned on a common crankshaft casting axis. Multiple crankpin journals are fixedly connected to the main journals by individual webs. Multiple lightening holes have individual ones of the multiple lightening holes integrally formed within individual ones of the crankpin journals during casting. A bubble space is located proximate to a mid-portion of selected ones of the multiple lightening holes of the crankpin journals. The bubble space locally increases a passage size of the selected ones of the multiple lightening holes and reduces a mass of the individual ones of the crankpin journals.

Klemstine, David C.↗
DOE OSTI2026

Affinity and Treatment of LDR Organics in Low Activity Waste by Cementitious Materials – 26109

The physiochemical interactions between organic contaminants, minerals, and polymer additives in grout/cementitious materials are being identified. This research supports a proposed Resource Conservation and Recovery Act (RCRA) treatment variance relevant to the Land Disposal Restriction (LDR) organics present in Hanford tank waste. It provides the technical basis to address the aspects documented by the Environmental Protection Agency in a draft memo necessary to establish that organics can be immobilized/stabilized in a cementitious matrix. The organic species may interact with cementitious minerals, including slag, fly ash, cement, and other components/dopants like activated carbon. A list of 132 reasonably expected LDR organics associated with Hanford tank waste (RPP-RPT-63493, Rev 1a) was screened by functional groups, octanol-water partitioning coefficients, and detection frequency in Hanford tank waste samples. A subset of 15 compounds spanning the identified properties was tested using sorption and leachate tests. These compounds were subjected to traditional batch sorption tests and leaching tests on/from Cast Stone cementitious material with and without activated carbon (a potential organic adsorption additive). The interactions between organic compounds were observed in traditional batch sorption and modified TCLP leachate tests for surrogate Cast Stone material with and without activated carbon addition. Specifically, phthalic acid (negatively charged) and 4-chloroaniline (polar) sorbed strongly to unmodified Cast Stone, while a group of three phenolic compounds (2,4,6-Trichlorophenol, Pentachlorophenol, o-Cresol) sorbed to and were retained by Cast Stone with a 1% activated carbon amendment. Mixtures of these compounds demonstrated visible retention of the organics within the matrix with a quantifiable affinity of the organics to the cement. This novel testing supports the notion that organics within Hanford tank waste would be retained onto the cement phase with the addition of simple materials easily added to the formulation as part of the treatment process. To further provide additional support to this claim, models employing Flory-Huggins theory in conjunction with macromolecular and organic molecule solubility parameters and species activity coefficients are being utilized to better understand these interactions. Within this context, Van Krevelen (VK) and Hansen organic and polymer solubility parameters were used to inform the Flory-Huggins interaction parameter, allowing for a quantifiable method of evaluating polymer-solvent compatibility and, by extension, interactions with proposed binding additives (e.g., activated carbon). These models and measurement should test the hypothesis for our systems understanding and applicability of Flory-Huggins theory, and whether the prediction of organics in the polymer phase versus the aqueous phase can be confidently made using this strategy. The estimation of the organic molecular activity coefficient in these high salt-saturated aqueous systems is another factor that will be assessed. This project aims to predict and understand complicated organic interactions in these heterogenous systems, guiding optimal treatment and stabilization methodologies.

Jolin, Will [Savannah River National Laboratory (S↗
DOE OSTI2020

Effect of copper content on the tensile elongation of Al–Cu–Mn–Zr alloys: Experiments and finite element simulations

Microstructures of cast aluminum alloys used in automotive engine applications often consist of intermetallic particles that can impact the tensile elongation of these alloys. Here in this paper, we investigate the effect of intermetallic grain boundary particles on tensile elongation by fabricating a series of alloys with Cu content varying between 6.0 - 9.0 wt% in cast Al–Cu–Mn–Zr (ACMZ) type compositions. The tensile elongation of as-aged ACMZ alloys decreases monotonically with increase in Cu content. While the microstructure within the grains and yield stress of the alloy remains invariant with Cu content, the decrease in tensile elongation correlates well with increase in the size and volume fraction of grain boundary particles. Microstructural observations are combined with finite element simulations to explain the trend in tensile elongation with changing Cu content. Crack initiation is found to occur by brittle fracture of the grain boundary particles. Increase in particle size promotes crack initiation by reduction in size dependent particle fracture strength. Lower inter-particle spacing at higher particle volume fraction further facilitates crack initiation by increasing stress within the particles caused by the interaction between stress fields of neighboring particles. Increase in particle volume fraction also accelerates crack propagation through the formation of macro shear zones in the microstructure. The increase in Cu content of cast ACMZ alloys, therefore, decreases tensile elongation by promoting both crack initiation and crack propagation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of carbonation on leaching of constituents from a cementitious waste form for treatment of low activity waste at the DOE Hanford site

Carbonation can be a major aging process during disposal of alkaline cementitious waste forms and can impact constituent leaching by changes in material alkalinity, pore structure, and controlling mineral phases. The effect of carbonation on the leaching of major and trace constituents from Cast Stone, a cementitious waste form developed to treat high salt content low activity waste, was studied through a combination of leaching experiments and reactive transport simulations. Diffusive transport of constituents in the waste form was evaluated using reactive transport modeling of diffusion-controlled leaching test results and a geochemical speciation model derived from pH-dependent leaching. Comparisons between Cast Stone materials aged under nitrogen, air, and 2% carbon dioxide in nitrogen showed that carbonation impacts solubility, physical retention and observed diffusivity of major and trace constituents. Carbonation under 2% CO 2 decreased the diffusion-controlled leaching of chromium by two orders of magnitude. Finally, modeling results suggest that carbonation may also decrease solubility of technetium while changes to microstructure by carbonation increases effective diffusivity of constituents in Cast Stone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Development of a Castable High Strength Secondary Aluminum Alloy from Recycled Wrought Aluminum Scrap

A new process for recycling scrap AA7075 aerospace alloys directly into a high strength castable secondary alloy is demonstrated. The process involves enhancing the castability of the utilized primary wrought aluminum scrap feedstock by scrap alloy chemistry optimization and zirconium additions in order to mitigate the inherent hot tearing tendency of 7075 alloys. By utilizing the new process, the hot tearing index of scrap AA7075 was reduced from 26 to 4. Defect-free castings were obtained in pilot-scale castings trials. The developed secondary 7075 alloy also satisfied preset target mechanical properties with strength levels exceeding 250 MPa and elongation levels higher than 3%. The validity of the new approach and its readiness for transition to commercial practice was demonstrated by casting cylinder heads directly from the modified 7075 scrap.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Novel Fuel Form Fabrication

Novel fuel form fabrication efforts have focused on casting of smaller diameter fuels in order to show the feasibility of the FAST test and the incorporation of a FCCI barrier either integral to the fuel or within the cladding tube. Casting of small diameter fuel slugs proved to be feasible at least one pin at a time using vacuum assisted arc casting. Integration of an integral FCCI barrier is also feasible although additional refinement will be necessary. If a sodium bonded fuel is employed, a more simple FCCI barrier may be to incorporate a thin barrier of material in the cladding before the sodium and fuel are loaded. Experiments have shown that sodium bonding of the barrier material and fuel is feasible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗