Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 1: Program description and data analysis

It was previously observed that an incident acoustic field on a wing with laminar flow can cause transition to turbulent flow if the fluctuating acoustic velocities are of sufficient amplitude and in the critical frequency range for an unstable laminar boundary layer. A section of a wing was modified with a natural laminar flow (NLF) glove to allow direct measurement of the effect of varying engine noise on the extent of laminar flow. The flight test program was completed in June, 1985. At each flight condition, the engine power was varied from about 2600 r/min (idle) to about 4500 r/min (maximum continuous power). The spectral data provides considerable insight into the influences of the various sound sources that contribute to the overall noise levels. Additional analysis will be required to assess the impact of these sources on boundary layer transition. These results demonstrate that substantial laminar flow on the wing of a transport configuration with wing-mounted engines can be obtained.

Source record↗
NASA NTRS1989

The structure of sheared turbulence near a plane boundary

The effects of shear on the structure of turbulence near a plane boundary are examined. Inhomogeneous rapid distortion theory is applied to a uniform-shear boundary layer (USBL) with a slip velocity condition at the surface. The effects of blocking the vertical component of the turbulence by the boundary in a USBL are compared with the effects in a shear-free boundary layer. It is shown that the blocking is only slightly modified by the presence of shear. The shear does alter the way in which the boundary influences the horizontal components and the turbulent shear stress near the horizontal component.

Lee, Moon Joo↗
NASA NTRS1956

Investigation of the Effectiveness of Boundary-layer Control by Blowing over a Combination of Sliding and Plain Flaps in Deflecting a Propeller Slipstream Downward for Vertical Take-off

An investigation was conducted in order to determine the effectiveness of blowing a jet of air over the flaps of a wing equipped with a 50-percent-chord sliding flap and a 25-percent-chord plain flap in deflecting a propeller slipstream downward for vertical take-off and the results are presented herein. The effects of a leading-edge slat, ground proximity, end plate, and propeller position were also investigated. The tests were conducted in a static-thrust facility at the Langley Aeronautical Laboratory.

AIRPLANES - PERFORMANCE↗
NASA NTRS1984

Effect of mixed (boundary) pixels on crop proportion estimation

In estimating acreage proportions of crop types in a segment using Landsat data, considerable problem is caused by the presence of mixed pixels. Due to lack of understanding of their spectral characteristics, mixed pixels have been treated in the past as pure while clustering and classifying the segment data. This paper examines this approach of treating mixed pixels as pure pixels and the effect of mixed pixels on the bias and variance of a crop type proportion estimate. First, the spectral response of a boundary pixel is modeled and an analytical expression for the bias and variance of a proportion estimate is obtained. This is followed by a numerical illustration of the effect of mixed pixels on bias and variance. It is shown that as the size of the mixed pixel class increases in a segment, the variance increases, however, such increase does not always affect the bias of the proportion estimate.

Chhikara, R. S.↗
NASA NTRS2009

On the Effects of Surface Roughness on Boundary Layer Transition

Surface roughness can influence laminar-turbulent transition in many different ways. This paper outlines selected analyses performed at the NASA Langley Research Center, ranging in speed from subsonic to hypersonic Mach numbers and highlighting the beneficial as well as adverse roles of the surface roughness in technological applications. The first theme pertains to boundary-layer tripping on the forebody of a hypersonic airbreathing configuration via a spanwise periodic array of trip elements, with the goal of understanding the physical mechanisms underlying roughness-induced transition in a high-speed boundary layer. The effect of an isolated, finite amplitude roughness element on a supersonic boundary layer is considered next. The other set of flow configurations examined herein corresponds to roughness based laminar flow control in subsonic and supersonic swept wing boundary layers. A common theme to all of the above configurations is the need to apply higher fidelity, physics based techniques to develop reliable predictions of roughness effects on laminar-turbulent transition.

Choudhari, Meelan M.↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1972

Effects of roughness on heating and boundary-layer transition. Part 2: effects of discrete roughness on heating

A preliminary investigation on the effects of roughness on heating in delta wing orbiters was conducted on the windward surface of the vehicle. The purpose of the experiment was to determine the feasibility of using parametric relationships obtained from discrete roughness effects on heating in flat plates and cones, to complex shuttle configurations. An attempt was also made to characterize what parameters were needed to influence roughness. Experimental results show that effective roughness Reynolds numbers are less than or equal to those of flat plates at the same edge Mach number, but, the roughness correlations for plates and cones cannot be applied to the shuttle configuration.

Mateer, G. G.↗
NASA NTRS1978

The effect of load in a contact with boundary lubrication

The effect of the transition load on the wear in a contact with boundary lubrication was investigated. An experimental method was developed for this purpose, and parameters affecting the boundary lubrication under industrial operating conditions were identified. These parameters are the adsorbed boundary film, the contact microgeometry (surface roughness), macrogeometry, and hardness of materials used. It was found that the curve of the tops of the surface protrustion affect the transition load, and thus the boundary lubrication. The transition load also depends on the chemical nature of the contact and its geometrical and mechanical aspects.

Georges, J. M.↗
NASA NTRS1983

A mixing-length model for the prediction of convex curvature effects on turbulent boundary layers

A mixing-length model is developed for the prediction of turbulent boundary layers with convex streamwise curvature. For large layer thickness ratio, delta/R greater than 0.05, the model scales mixing length on the wall radius of curvature, R. For small delta/R, ordinary flat wall modeling is used for the mixing-length profile with curvature corrections, following the recommendations of Eide and Johnston (1976). Effects of streamwise change of curvature are considered; a strong lag from equilibrium is required when R increases downstream. Fifteen separate data sets were compared, including both hydrodynamic and heat transfer results. Six of these computations are presented and compared to experiment.

Adams, E. W.↗
NASA NTRS1972

Displacement interaction and surface curvature effects on hypersonic boundary layers.

The title problem was studied employing implicit finite-difference methods to obtain numerical solutions to a composite set of boundary-layer equations valid to second order. Results are given for flow up a two-dimensional cubic compression ramp for free-stream Mach numbers of 6, 8, and 12.25 and for free-stream Re/inch equal to 85,800 and 25,800 at a wall-to-stagnation temperature ratio of 0.223. Comparisons with independent theories and experimental results are given. Nonsingular separation was produced at a free-stream Mach number of 12.25. For all cases considered, displacement and curvature effects canceled one another when a consistent treatment of inviscid and viscous curvature corrections was employed - the second-order theory virtually reproducing the first-order results.

Wornom, S. F.↗
NASA NTRS1976

Aeroacoustics

A review of the acoustics of moving media is provided, taking into account a derivation of basic equations, wave-like solutions of acoustic equations, the solutions of acoustic equations by superposition of elementary sources, the source distribution in unbounded regions, the radiation field, energy relations, and moving sound sources. The characteristics of aerodynamic sound are considered along with the effect of solid boundaries, the effect of uniform flow, acoustic field equations, and the effects of nonuniform mean flow on the generation of sound. Attention is given to Lighthill's acoustic analogy, the solution of Lighthill's equation when no solid boundaries are present, the application of Lighthill's theory to turbulent flows, and the physics of jet noise.

Goldstein, M. E.↗
DOE OSTI2022

Effect of Grain Boundary Misorientation on Spall Strength in Ta via Shock-Free Simulations with Relatively Few Atoms

A suite of 37 molecular dynamics simulations is conducted at two system sizes to systematically characterize the role of grain boundary (GB) misorientation on spall strength in pure BCC tantalum (Ta). The systems studied consist of bicrystals with a single [110] symmetric tilt grain boundary. Two loading conditions are compared: (i) homogeneous extension under uniaxial strain simulated in this study and (ii) piston/flyer impact of sample, which induces heterogeneous deformation via shockwave propagation along the length of the sample. The piston/flyer impact is taken from the literature and run on the same set of GB misorientation angles using LAMMPS. The major finding here is that both methods result in similar spall strength predictions, but the homogeneous extension method generally requires two to three orders of magnitude fewer atoms and similar reductions in computational costs. Spall strength results systematically overpredict using this method, by about 10% for the dataset three orders of magnitude smaller than piston/flyer simulations, and 5% for the dataset two orders of magnitude smaller. Lastly, the effect of system size and pre-compression magnitude on spall strength is systematically characterized.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Modeling variable blowing effects in the turbulent hypersonic boundary layer

Studies of the effects of variable blowing in turbulent hypersonic boundary layers are presented. Numerical calculations of the skin friction and surface heat transfer rates are compared to the experimental measurements of Holden (1990) for a slender cone at zero angle of attack in steady flows at Mach numbers of 11 and 13. An analysis of the transpiration feed system of the cone model was performed and showed that the blowing rate could be variable along the cone surface. This effect is confirmed by internal pressure measurements which were taken inside the cone model. The blowing rates are recalibrated using the internal gauge readings and used as the wall boundary condition for a compressible turbulent boundary layer calculation using the low Reynolds number k-epsilon model of Chien (1982). At low blowing rates, the boundary layer calculations indicate that a situation where both the effects of suction and blowing are present within the same flow. The results show excellent qualitative prediction of the experimental data.

Vanosdol, John G.↗
NASA NTRS1988

Calculation of aerodynamic characteristics of airplane configurations at high angles of attack

Calculation of longitudinal and lateral directional aerodynamic characteristics of airplanes by the VORSTAB code is examined. The numerical predictions are based on the potential flow theory with corrections of high angle of attack phenomena; namely, vortex flow and boundary layer separation effects. To account for the vortex flow effect, vortex lift, vortex action point, augmented vortex lift and vortex breakdown effect through the method of suction analogy are included. The effect of boundary layer separation is obtained by matching the nonlinear section data with the three dimensional lift characteristics iteratively. Through correlation with results for nine fighter configurations, it is concluded that reasonably accurate prediction of longitudinal and static lateral directional aerodynamics can be obtained with the VORSTAB code up to an angle of attack at which wake interference and forebody vortex effect are not important. Possible reasons for discrepancy at higher angles of attack are discussed.

Tseng, J. B.↗
DOE OSTI2025

The effect of grain boundary yield and disconnections on grain boundary fracture strength

During high-temperature interfacial strain, e.g., creep or sintering, grain boundaries will sample non-equilibrium states associated with the non-equilibrium disconnections that mediate strain. This work tests the hypothesis that those non-equilibrium states should affect the mechanical properties of the grain boundary. High-temperature bicrystal tensile strain experiments performed on Sc-doped ZrO 2 as a function of strain rate enable the observation of fracture before and after grain boundary yield. Yielded boundaries exhibit a median fracture strength ≈ 50 % lower than those that did not yield. Molecular dynamics simulations performed on boundaries with and without interstitial-type disconnection loops indicate that the presence of those loops reduce the failure stress.

36 MATERIALS SCIENCE↗