Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bolts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1969

Bolt torque tests in vacuum

Test equipment and tests to determine effects of vacuum environment on release torque of threaded fasteners

Demorest, K. E.↗
NASA NTRS1978

Adding through-bolt holes to pin-fin cold plates

Spot-welding technique is less expensive than secondary-brazing and electron-beam methods. With procedure, standard plates can be modified in quantity for various mounting configurations without need for special tooling.

Ruppe, E. P.↗
NASA NTRS1979

Behavior of composite bolted joints at elevated temperature

Experimental results from an investigation which examines the combined effects of temperature, joint geometry and out-of-plane constraint upon the response of mechanically fastened composite joints are presented. Data are presented for simulated mechanically fastened joint conditions in two laminate configurations fabricated from Hercules AS/3501-6 graphite-epoxy. Strength and failure mode results are presented for the test temperatures of 21 C, 121 C and 177 C and for a range of the geometric parameters W/D and e/D from 3.71 to 7.43 and 1.85 to 3.69, respectively. A hole diameter, D of 5.16 mm was utilized for all tests. Pin bearing tests with out-of-plane constraint were conducted at room temperature only. All elevated temperature data were generated for pin bearing conditions. Ultrasonic C scan inspection of the failed specimens was employed to assess the damage region and to determine failure mode. Comparative data are presented for pin bearing and out-of-plane constraint conditions for the above mentioned joint configurations. The joint under pin loading was modeled by two dimensional finite element methods. Predicted net section strain concentrations were compared with experimental results.

Wilson, D. W.↗
NASA NTRS1981

Two-headed bolt

Coarse, multi-ingredient suspensions are sprayed on surface smoothly and uniformly with aid of nozzle attachment for commercial spray gun. Nozzle attachment is contoured internally to suppress overspray and to prevent spray from segregating. From its conical inlet, nozzle converges smoothly to throat, then diverges in bell-shaped chamber that allows suspension to flow uniterruptedly without building up turbulently in nozzle. End of nozzle is adjustable and can be extended or retracted to avoid dripping when inlet pressure, pump pressure, or density of mixture changes.

Jeffers, G. W.↗
NASA NTRS1981

Use of two-dimensional transmission photoelastic models to study stresses in double-lap bolted joints

The stress distribution in two hole connectors in a double lap joint configuration was studied. The following steps are described: (1) fabrication of photoelastic models of double lap double hole joints designed to determine the stresses in the inner lap; (2) assessment of the effects of joint geometry on the stresses in the inner lap; and (3) quantification of differences in the stresses near the two holes. The two holes were on the centerline of the joint and the joints were loaded in tension, parallel to the centerline. Acrylic slip fit pins through the holes served as fasteners. Two dimensional transmission photoelastic models were fabricated by using transparent acrylic outer laps and a photoelastic model material for the inner laps. It is concluded that the photoelastic fringe patterns which are visible when the models are loaded are due almost entirely to stresses in the inner lap.

Hyer, M. W.↗
NASA NTRS1982

Results of tests of MTA-2 TPS on the SRB hold-down bolt blast container

The four solid rocket booster (SRB) hold-down posts are fastened to the mobile launch platform (MLP) with four large nuts. At liftoff the nuts are split with explosive changes to release the SRB/Shuttle. A blast container is placed over the nuts to protect the vehicle from flying debris. The blast container is a reusable part and has to be protected from aerodynamic heating during flight. The thermal protection system (TPS) used to protect these blast containers is cork. Fitting the flat cork sheet to this hemispherical shaped blast container is both time consuming and expensive. Another problem is removing the charred cork and epoxy glue from the blast containers. Replacements of this cork with another TPS material such as MTA-2 was examined. Heating rates along the centerline of the forward facing areas of the blast container were determined. The feasibility of using 1/2 in. MTA-2 on the SRB blast containers for protection from ascent, plume impingement and reentry heating is demonstrated.

Dean, W. G.↗
NASA NTRS1988

Aircraft jolts from lightning bolts

The trend toward the use of composite materials and digital electronics has renewed the need to quantify the effects of lightning strikes to airplanes, since composite structures do not provide shielding equivalent to that of metal aircraft, and digital systems are potentially more susceptible to upset by electrical transients than are analog electronic systems. A research program, called the Storm Hazards Program, has been run by the National Aeronautics and Space Administration (NASA) for the past eight years and has provided the first statistically significant measurements of the electromagnetic interaction between lightning and aircraft. A NASA-owned F-106B airplane has been flown through thunderstorms about 1500 times at altitudes between 5,000 and 40,000 feet (1,500 to 12,000 meters). The airplane, lightning-hardened and outfitted with special instruments, was hit by lightning 714 times. The types of measurements made and the results are described.

Pitts, Felix L.↗
NASA NTRS1990

An apparatus for bearing-bypass testing of bolted joints

A dual-control test system measuring the strength of graphite/epoxy specimens under tension and compression for a wide range of bearing-bypass load ratios is presented. The bearing-bypass strengths of single-fastener specimens are measured for damage onset and ultimate failure and are plotted against one another. The results indicate that an initiated damage grows to failure in the same mode for most cases. However, if the damage is initiated in the compression-reacted-bearing mode, the specimens fail in the offset-compression mode. It is concluded that this type of transition can occur in multi-fastener joints under compression and complicate the strength predictions.

Crews, J. H., Jr.↗
NASA NTRS2003

Performance Testing of Thermal Interface Filler Materials in a Bolted Aluminum Interface Under Thermal/Vacuum Conditions

A thermal interface material is one of the many tools often used as part of the thermal control scheme for space-based applications. Historically, at Marshall Space Flight Center, CHO-THERM 1671 has primarily been used for applications where an interface material was deemed necessary. However, numerous alternatives have come on the market in recent years. It was decided that a number of these materials should be tested against each other to see if there were better performing alternatives. The tests were done strictly to compare the thermal performance of the materials relative to each other under repeatable conditions and do not take into consideration other design issues, such as off-gassing, electrical conduction, isolation, etc. The purpose of this Technical Memorandum is to detail the materials tested, test apparatus, procedures, and results of these tests. The results show that there are a number of better performing alternatives now available.

Glasgow, S. D.↗