SEARCH · Engineering Papers

Results for “blade design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Rafting-Enabled Recovery Avoids Recrystallization in 3D-Printing-Repaired Single-Crystal Superalloys

The repair of damaged Ni-based superalloy single-crystal turbine blades has been a long-standing challenge. Additive manufacturing by an electron beam is promising to this end, but there is a formidable obstacle: either the residual stress and γ/γ' microstructure in the single-crystalline fusion zone after e-beam melting are unacceptable (e.g., prone to cracking), or, after solutionizing heat treatment, recrystallization occurs, bringing forth new grains that degrade the high-temperature creep properties. Here, a post-3D printing recovery protocol is designed that eliminates the driving force for recrystallization, namely, the stored energy associated with the high retained dislocation density, prior to standard solution treatment and aging. The post-electron-beam-melting, pre-solutionizing recovery via sub-solvus annealing is rendered possible by the rafting (i.e., directional coarsening) of γ' particles that facilitates dislocation rearrangement and annihilation. The rafted microstructure is removed in subsequent solution treatment, leaving behind a damage-free and residual-stress-free single crystal with uniform γ' precipitates indistinguishable from the rest of the turbine blade. Finally, this discovery offers a practical means to keep 3D-printed single crystals from cracking due to unrelieved residual stress, or stress-relieved but recrystallizing into a polycrystalline microstructure, paving the way for additive manufacturing to repair, restore, and reshape any superalloy single-crystal product.

36 MATERIALS SCIENCE↗

DOE OSTI2021

HFIR SiC Bowing Test Ready to Insert

This report describes the successful assembly of a High Flux Isotope Reactor (HFIR) irradiation experiment designed to assess radiation-induced lateral bowing of silicon carbide fiber–reinforced, silicon carbide matrix composite (SiC/SiC) components under a radial fast neutron flux gradient. Excessive bowing of a SiC/SiC channel box in a boiling water reactor could potentially interfere with control blade movements. Similar concerns exist for SiC/SiC fuel cladding in light water reactors. The experiment described herein will provide experimental validation of the structural response of a miniature SiC/SiC channel box and tube specimens with pressurized water reactor diameters during irradiation. The significant radial fast neutron flux gradients that exist in the permanent reflector of HFIR were characterized using detailed three-dimensional neutronic calculations. The three-dimensional displacement damage dose rate profile and the resulting volumetric swelling in SiC were used as inputs to structural analyses that predicted the deformation and stresses in the channel box specimen. The specimens were thoroughly characterized prior to irradiation using traditional dimensional inspection and surface profilometry so that these measurements can later be compared with similar measurements that will be made post-irradiation to determine radiation-induced deformations. Furthermore, fine engraving markers were inscribed along all outer surfaces of the specimen and mapped using a digital microscope and a three-dimensional stage. This technique allowed for accurate measurements of the marker spacings, which can be compared with similar measurements that will be made post-irradiation to provide local radiation-induced strain mapping. The experiment was successfully assembled and is scheduled for insertion during HFIR cycle 492, which is currently scheduled to run from May 25, 2021 to June 18, 2021.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

High- and Mid-Fidelity Modeling Comparison for a Floating Marine Turbine System: Preprint

There is a lack of suitable numerical tools, particularly open-source tools, that can be used for designing and optimizing marine turbine systems. The National Renewable Energy Laboratory (NREL) has added features to their widely used mid-fidelity wind turbine modeling code, OpenFAST, to enable modeling of axial flow marine turbines. This necessitated the addition of several physical effects relevant to marine turbines that can be neglected for wind turbines. These include buoyant loads, added mass and inertia loads, wave-current superposition, and changes to the coordinate systems. This updated version of OpenFAST allows for the modeling of both fixed and floating marine turbine systems at a speed comparable to real time. While efficient for long simulations, large sets of load cases, and design studies, mid-fidelity codes cannot capture all of the potentially important physical phenomenon impacting marine turbine systems. High-fidelity computational fluid dynamics (CFD) simulations can capture more flow effects with fewer assumptions and provide detailed body pressure mapping and flow-field information. It is important to compare predictions between mid-fidelity and high-fidelity codes, both to verify the models and to understand the limitations. A floating marine turbine system designed by NREL was modeled both with OpenFAST and with the commercial CFD code, STARCCM+. The CFD model used a 3-D unsteady Reynolds-averaged Navier-Stokes solver for a volume-of-fluid numerical wave and current tank. The blade-resolved simulations used the sliding-interface technique for the spinning rotor and an overset grid to accommodate the rigid-body motion of the floating system. The mooring system was modelled with a custom coupling of the CFD solver with the open-source code, MoorDyn. This improves upon the existing quasi-static catenary solver in STARCCM+, which lacks seabed contact or line-to-line connections. Spatial and temporal convergence studies were conducted. The simulation results for a combined current and wave condition are compared between OpenFAST and CFD, highlighting the capabilities of the mid-fidelity code and identifying the areas where a high-fidelity approach is needed.

CFD↗

DOE OSTI2020

Preliminary Introduction of a Free Vortex Wake Method Into OpenFAST

Increasing wind turbine size can have substantial economic benefits. However, increasing wind turbine turbine size requires the use of models that accurately capture the aerodynamic response to large deflections and nonstraight blade geometries. Additionally, the installation of offshore floating turbines requires turbine models that can handle large rotor motion. Free vortex wake (FVW) methods are capable of modeling this type of complex physics while remaining computationally tractable to perform the many simulations necessary for turbine design. In this work, a FVW model is added to the National Renewable Energy Laboratory engineering tool OpenFAST to allow for the aerodynamic modeling of highly flexible turbines along with the aero-hydro-servo-elastic response capabilities of OpenFAST. Code implementation is not complete and thus no results are presented. However, areas of potential modeling improvement are discussed, such as modifications to the circulation calculation and the need for different FVW input model specifications when high-thrust cases are being modeled.

17 WIND ENERGY↗

DOE OSTI2022

Current state and future trends in boundary layer control on lifting surfaces

Successful flow control may bring numerous benefits, such as flow stabilization, flow reattachment, separation delay, drag reduction, lift increase, aerodynamic performance improvement, energy efficiency increase, shock delay or weakening, noise reduction, etc. For these purposes, many different flow control devices, which can be classified as passive, semi-active and active, have been designed and tested. This review paper aims to highlight the most promising and commonly employed boundary layer control methods as well as outline their potential in specific applications in aerospace and energy engineering. Referenced studies, performed on various geometries (flat plates, channels, airfoils, wings, blades, cylinders), are primarily numerical or experimental. Although enhanced aerodynamic performance is achieved in many cases, further research is required to draw general conclusions. This paper aims to demonstrate that, in the future, we may expect further developments of flow control actuators, as well as their increased application.

42 ENGINEERING↗

DOE OSTI2020

High Temperature, High AN2 Last Stage Blade for 65% Efficiency (Phase I Final Report)

GE Power (GEP), in partnership with GE Global Research (GEGR)(GEP and GEGR are divisions of General Electric Company) have hot and large Last Stage Blade (LSB) technologies necessary for state-of-the art gas turbines to successfully realize ~3100°F turbine inlet temperatures (TIT), an essential element to reaching the DOE goal of 65% combined cycle efficiency (CCeff). The objective of this project was to develop conceptual LSB designs and advance the technological understanding of synchronous vibrations (SV), nonsynchronous vibrations (NSV), and damping that limit the current state-of-the-art LSB designs and applications. In the Phase I project GE Power leveraged existing design and analysis knowledge and techniques for LSB design and performed extensive analytical evaluations to identify and characterize conceptual design concepts. The most promising designs are the basis for development and testing in a potential Phase II project.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2021

AOI [1]: Passive Wireless Sensor Systems Fabricated by Direct-Writing for Temperature and Health Monitoring of Energy Systems in Harsh-Environments (Final Report)

Researchers at West Virginia University (WVU) propose to demonstrate a wireless, high-temperature sensor system for monitoring the temperature and health of energy-system components. The active sensor and electronics for wireless communication will be composed entirely of an electroceramic materials (conductive ceramics) which are capable of withstanding the harsh-environments required for fossil energy-based technologies. This work will focus primarily on the fabrication and testing of temperature (thermocouples and thermistors) and health (strain/stress and crack propagation sensors) that function at extreme temperatures (up to 700-1700ºC). The electronics will accompany the high-temperature sensor, which will include a passive wireless communication circuit that allows the transmission of the data based on the LCR resonance principle to a near-by reader antenna. This passive transmission of data will reduce the need for interconnect wires near the active, and possibly rotating, energy-system component. The research will include process development to permit the 2D/3D direct-writing of the entire sensor and communication circuit onto the energy-system component. The direct-writing will be facilitated by using silicon-based polymer-derived precursors to form the high-temperature, stable electroceramic compositions. In addition, methods for direct-writing the circuit onto a fugitive carrier substrate will be completed, which will permit a “peel-and-stick”-like transfer of the sensor circuit to the energy-system component. This feature will allow the economical and precise placement of the sensor circuit onto components of various shapes and locations, without altering the geometry and active features of the manufactured component, or the removal (or decommissioning) of the component for installation. The proposed work will be directed at the following areas: 1) Investigation of phase formation, sintering/grain growth, and electrical properties of polymer-derived electroceramic composites; 2) Definition of processes to direct-write through ink-jet and robo-casting the polymer-derived electroceramic composites onto oxide and polymer surfaces; 3) Development of methods to form monolithic "peel-and-stick" preforms that will efficiently transfer the sensor circuit to ceramic surfaces after thermal treatment; 4) Design of passive wireless LCR circuits and receiver (reader) antennas for communication and testing at high temperatures; 5) Investigation of the passive wireless sensor system developed (and method of transferring sensor system) for temperature and stress/strain measurements on a SOFC repeat unit and a singular gas turbine blade prototype as example applications.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Extreme hardness at high temperature with a lightweight additively manufactured multi-principal element superalloy

Materials are needed that can tolerate increasingly harsh environments, especially ones that retain high strength at extreme temperatures. Higher melting temperature alloys, like those consisting primarily of refractory elements, can greatly increase the efficiency of turbomachinery used in grid electricity production worldwide. Existing alloys, including Ni- and Co-based superalloys, used in components like turbine blades, bearings, and seals, remain a performance limiting factor due to their propensity, despite extensive optimization efforts, for softening and diffusion-driven elongation at temperatures often well above half their melting point. To address this critical materials challenge, we present results from integrating additive manufacturing and alloy design to guide significant improvements in performance via traditionally difficult-to-manufacture refractory alloys. We present an example of a multi-principal element alloy (MPEA), consisting of five refractory elements and aluminum, that exhibited high hardness and specific strength surpassing other known alloys, including superalloys. The alloy shows negligible softening up to 800°C and consists of four compositionally distinct phases, in distinction to previous work on MPEAs. Density functional theory calculations reveal a thermodynamic explanation for the observed temperature-independent hardness and favorability for the formation of this multiplicity of phases.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Heat Transfer Experiments of Ribbed, Serpentine Cooling Passages with Supercritical CO2

The results of heat transfer experiments with supercritical CO2 (sCO2) to capture the performance of ribbed, serpentine cooling passages for Reynolds numbers in the range of 100,000 - 400,000 are presented. The oxy-combustion turbine operating in an Allam-Fetvedt cycle has a turbine inlet temperature exceeding 1100°C, necessitating internally cooled turbine blades due to material creep strength limits. Reynolds numbers for sCO2, with its combination of high fluid density and low viscosity, can be up to an order of magnitude higher than comparable internal cooling conditions for an air-breathing engine where the majority of experimental data exists. To improve the prediction of cooling performance through turbulated passages, a test rig was designed and constructed with interchangeable insert capability for operation in sCO2 with heat transfer from a heater outlet flow stream to a lower temperature recuperator outlet flow stream. The inserts included serpentine passage geometry with five passes, one of the inserts including chevron ribs and the other a plain wall. The multi-pass serpentine geometry allowed for the evaluation of the effects 180 deg. tip turns have on the return passage flow characteristics, as they can depart significantly from fully-developed flow characteristics. The test procedure included the use of a modified Wilson plot method, with hot flow stream conditions kept effectively constant so that monitored changes in the overall thermal resistance could be attributed to manipulations in cooling flow stream conditions. Conditions during testing consisted of test section pressures of approximately 180 bar, cooling flow stream temperature of 175°C and hot flow stream temperature of 410°C. Test points at discrete cool flow Reynolds numbers up to 400,000 demonstrated an expected trend of decreased fluid thermal resistance with increasing Reynolds number, while at comparable Reynolds number there was an exhibited lower thermal resistance and higher passage pressure drop for the ribbed insert compared to the plain-walled insert. Processing of test data included establishment of Nusselt number enhancement ratios, so that for different internal cooling passage dimensions in the actual turbine blade at comparable Reynolds number the ratio could be applied to predict cooling performance.

Marshall, Michael↗

DOE OSTI2021

Flexing the Limits of Land-Based Wind Turbine Rotor Growth

The Big Adaptive Rotor (BAR) project aims to design and enable the next generation of land-based wind turbines with 206-meter (m) rotors, which will increase capacity factors by 10% or more over a typical land-based turbine. High-energy-capture turbines have many advantages, but the length and width of larger turbine blades to enable these machines creates transportation challenges that must be overcome to make true on the adage, bigger is better.

49 EE - Wind and Water Power Program - Wind (EE-4W↗

DOE OSTI2021

Controlled Pyrolysis: A Robust Scalable Composite Recycling Technology

The reinforced composites industry is facing significant challenges in handling the scrap composite material from automobile manufacturing, the wind turbine industry, and others. The fibers in the material, whether they be carbon, glass, or other materials have commercial value if they can be recovered successfully. Successfully means the fibers are clean with no sizing or other binders and have adequate strength and physical properties that would allow them to be economically reprocessed into valuable product. The composites recycling project was an industry-collaborative effort to develop a composite recycling technology using controlled pyrolysis. Through the recycling of scrap and end-of-life (EOL) cured composite materials, this pilot study was intended to create a business case by realizing a cost-effective means for recycling EOL and production scrap composite materials, ultimately reducing the volume of composite materials destined for landfill. The project was led by the Institute for Advanced Composites Manufacturing Innovation (IACMI), the American Composites Manufacturers Association (ACMA), Oak Ridge National Laboratory (ORNL), Continental Structural Plastics (CSP) a Teijin Group Company, CHZ Technologies, and A. Schulman with support from Owens Corning, John Deere, General Electric (GE), Ashland LLC, and Plastics Europe (CEFIC). The team studied and tested CHZ Technologies’ controlled pyrolysis system, known as the Thermolyzer TM , which operates on a scalable basis to convert organic polymer materials into a clean synthesis gas and char containing the recoverable carbon and glass fiber reinforcement. The recoverable energy contained in the input polymers creates the synthesis gas that can be used to provide heat to the Thermolyzer TM primary reactor in a sustainable manner. That is, once the Thermolyzer TM is started with a small amount of external natural gas, the synthesis gas that is created from the polymers will continue to operate the burners so long as feedstock is supplied. The reinforcing fiber materials remaining in the solid phase char were separated and cleaned for re-use in other polymer systems based on the retained properties of the fibers. The study created reports (attached in the appendix) on the Mass and Energy Balances, syngas analytics, VOC assessment, yield analysis and other analytics necessary for a Techno-Economic Analysis (TEA) to quantify the economic impact of the recovery and sustainable re-use of the carbon and glass fibers. The process consisted of 4 steps: Selection of 4 samples of cured composite waste materials from project partners interested in materials recycling and recovering the reinforcing fibers for best case re-use. The materials included glass fiber (GF) polyester/vinyl ester automotive SMC from CSP, GF epoxy balsa/PVC foam wind blades from GE, carbon fiber (CF) epoxy wind blade laminated spar caps from GE, and GF/CF epoxy hybrid assembly from John Deere. Processing the waste composite samples into 1-2” shreds. Packaging the shredded composites into bulk sacks on international shipping pallets for shipment to KUG in Forst (Lausitz), Germany. Pyrolysis of the shredded composites under controlled conditions designed for each polymer system. Collecting samples of the gas and char for analysis. Shipping the char containing the CF/GF back to the US for the next steps of testing the fibers and developing protocols for sustainable re-use of the fibers in composite applications.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Difference in load predictions obtained with effective turbulence vs. a dynamic wake meandering modeling approach

Abstract. According to the international standard for wind turbine design, the effects of wind turbine wakes on structural loads can be considered in two ways: (1) by augmenting the ambient turbulence levels with the effective turbulence model (EFF) and then calculating the resulting loads and (2) by performing dynamic wake meandering (DWM) simulations, which compute wake effects and loads for all turbines on a farm at once. There is no definitive answer in scientific literature as to the consequences of choosing one model over the other, but the two approaches are unarguably very different. The work presented here expounds on these differences and investigates to what extent they affect the simulated structural loads. We consider an idealized 4×4 rectangular array of National Renewable Energy Laboratory 5 MW wind turbines with a spacing of 5 by 8 rotor diameters and three wind speed scenarios at high ambient turbulence. Load simulations are performed in OpenFAST with EFF and in FAST.Farm with the DWM implementation. We compare ambient turbulence, wind farm turbulence, and loads between both approaches. When omnidirectional results are compared, EFF wind farm turbulence intensity is consistently higher by 0.2 % (above-rated wind speed) to 2.7 % (below-rated wind speed). However, for certain wind directions, the EFF turbulence can be lower than FAST.Farm by almost 9 %. Wind speeds within the farm were found to differ by up to 3 m s−1 due to the lack of wake deficits in the EFF approach, leading to longer tails toward low values in the FAST.Farm mean load distributions. Consistent with the turbulence results, the median EFF load standard deviations are also consistently higher, by a maximum of 20 % and 17 % for blade-root out-of-plane and tower-base fore-aft moments, respectively.

17 WIND ENERGY↗

DOE OSTI2023

2022 Prototype Manufacture and Installation Awardee: Sonsight Wind

The Sonsight Wind 3.5-kilowatt (kW) prototype turbine is designed to compete with solar power, meeting energy needs for a wide range of smaller-scale applications, such as powering individual homes and irrigation systems on farms and ranches in remote areas. The technology's innovative high-torque, low-rotations-per-minute generator permits the use of longer blades that, at moderate wind speed sites, generate the energy of a 5-kW turbine with lower thrust forces than similarly rated turbines. The 3.5-kW turbine is projected to ofer greater durability at a signifcantly lower levelized cost of energy. Sonsight Wind advanced the development of the prototype with a previous Competitiveness Improvement Project (CIP) funding award.

competitiveness improvement project↗

DOE OSTI2026

Power performance and loads characterization of laboratory-scale cross-flow rotors fabricated using additive manufacturing

Tidal energy conversion is a relatively new application for additive manufacturing (AM), where the focus has been on fabricating axial-flow turbine blades. AM techniques add material precisely where it is needed, creating more complex shapes with less waste. Cross-flow rotor geometry presents an opportunity for AM to improve rotor performance by fabricating features that cannot be created economically via conventional manufacturing. The challenges associated with using AM in cross-flow design include water resistance and degradation over time while retaining a level of quality equivalent to conventionally machined parts. In this work, AM materials were tested by environmentally conditioning samples in a seawater tank for 5 months, followed by performance and phase-resolved load testing of laboratory-scale rotors in a hydraulic flume. We found that while metals like titanium and Inconel have excellent performance in marine environments, achieving the desired geometry and performance is difficult. Thermoplastics degraded in seawater but were easier to form into desired geometries and could exceed the performance of an aluminum control rotor. Warping and surface finish were significant detractors from AM rotor performance. These results suggest that the primary benefits of using AM for cross-flow rotors is to quickly fabricate and test unconventional rotor geometries.

16 TIDAL AND WAVE POWER↗

DOE OSTI2024

2024 OES-Environmental 2024 State of the Science Report, Chapter 9: Beyond Single Marine Renewable Energy Devices: A System-wide Effects Approach

Global expansion of renewable energy, including marine renewable energy (MRE) technology development is necessary to mitigate the effects of climate change, facilitate a sustainable transition from carbon-based energy sources, and satisfy national energy security needs using locally produced electricity (European Commission 2022; IPCC 2023; IRENA 2020). As MRE engineering and research continue to focus on designing devices for deployment in nearshore and offshore waters around the world, researchers are also examining potential environmental effects on marine animals, habitats, and ecosystem processes. To date, the focus has been on interactions between small numbers of MRE devices (1-6) and the environment, such as collisions between animals and turbine blades, the effects of underwater noise and electromagnetic field (EMF) emissions, changes in habitats and oceanographic processes, risk of entanglement of animals, and displacement of animals (Boehlert & Gill 2010; Copping & Hemery 2020) (see Chapter 3).

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

A Power Takeoff Device for a Small Marine Hydrokinetic Turbine Deployed from an Unmanned Floating Platform

The design, development, and field-testing of a power takeoff (PTO) device equipped with a ball-type continuously-variable transmission (B-CVT) for a small marine hydrokinetic (MHK) turbine deployed from a floating unmanned autonomous mobile catamaran platform is described. The turbine is a partially-submerged multi-blade undershot waterwheel (USWW). The objective is to develop a PTO for the optimal conversion of the MHK energy harnessed by the turbine to electric power, which is stored in battery banks onboard the MHK platform. Modeling, simulation, and bench testing of the USWW and PTO show the feasibility of utilizing the B-CVT's variable gear ratio to decouple the USWW and generator speeds, maintaining the waterwheel within its optimal tip speed ratio (TSR) while varying the generator speed, thereby increasing the efficiency of the PTO. Results of bench and field testing in support of characterizing the power conversion capabilities of the PTO are described. The system being developed is in support of potential self-powered autonomous mobile recharge stations for unmanned aerial vehicles (U A V s) operating in coastal zones. Field tests of the complete MHK platform with 9 blades on the waterwheel and wheel sub mergences of 10 and 12 inches (full blade submergence) were performed. The overall proof-of-concept was successfully demonstrated, with the system satisfactorily capturing and converting water flow energy into electricity. The feasibility of utilizing the B-CVT as a means of increasing the PTO power capture capabilities and efficiency is analyzed.

Pimentel, Hugo↗

DOE OSTI2023

TEAMER: Experimental performance characterization of a shrouded axial-flow turbine

Sitkana has developed a shrouded hydrokinetic turbine with a modular, low-cost design that can be scaled to meet the needs of remote communities. With technical support from the University of Washington, Sitkana sought to experimentally characterize the mechanical power and structural loads of various 1:3.3 scale rotor geometries. In all, 11 different rotor geometries were characterized with variations in height-to-diameter ratio, blade number, and blade type (foiled versus flat). All tests were conducted in Reynolds-independent flow conditions in the Alice C. Tyler Flume at the University of Washington. Results allow Sitkana to (1) refine the optimal rotor geometry, (2) validate numerical models, and (3) predict power output for a full-scale system. This project is part of the TEAMER RFTS 8 (request for technical support) program.

16 TIDAL AND WAVE POWER↗

DOE OSTI2022

The Circular Economy Lifecycle Assessment and Visualization Framework - CELAVI

A circular economy (CE) aims to decouple human activities from economic growth and resource use, and its overall goal is reducing or avoiding negative environmental externalities. The newly developed Circular Economy Lifecycle Assessment and Visualization (CELAVI) framework simulates changes in supply chain environmental impacts as it transitions toward circularity. This study expands CELAVI by incorporating detailed spatial resolution and real-world road routes connecting all facilities within the system. The case study on end-of-life decision making of wind turbine blades in the states of Iowa and Missouri explores how supply chain circularity and environmental impacts are affected by pathway costs and level of wind turbine installations. It demonstrates how high circularity costs might be beneficial for circularity transitions given revenue generated from circular pathways. Finally, impacts have important contributions to the supply chain design and thus show the importance of including detailed spatial resolution in CELAVI and CE studies in general.

circular economy↗