Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Unsteady Turbine Blade and Tip Heat Transfer Due to Wake Passing

The geometry and the flow conditions of the first stage turbine blade of GE s E3 engine have been used to obtain the unsteady three-dimensional blade and tip heat transfer. The isothermal wall boundary condition was used. The effect of the upstream wake of the first stage vane was of interest and was simulated by provision of a gust type boundary condition upstream of the blades. A one blade periodic domain was used. The consequence of this choice was explored in a preliminary study which showed little difference in the time mean heat transfer between 1:1 and 2:3 vane/blade domains. The full three-dimensional computations are of the blade having a clearance gap of 2 percent the span. Comparison between the time averaged unsteady and steady heat transfer is provided. It is shown that there is a significant difference between the steady and time mean of unsteady blade heat transfer in localized regions. The differences on the suction side of the blade in the near hub and near tip regions were found to be rather significant. Steady analysis underestimated the blade heat transfer by as much as 20 percent as compared to the time average obtained from the unsteady analysis. As for the blade tip, the steady analysis and the unsteady analysis gave results to within 2 percent.

Ameri, Ali A.↗
NASA NTRS1951

Coolant-Flow Calibrations of Three Simulated Porous Gas-Turbine Blades

An investigation was conducted at the NACA Lewis laboratory to determine whether simulated porous gas-turbine blades fabricated by the Eaton Manufacturing Company of Cleveland, Ohio would be satisfactory with respect to coolant flow for application in gas-turbine engines. These blades simulated porous turbine blades by forcing the cooling air onto the blade surface through a large number of chordwise openings or slits between laminations of sheet metal or wire. This type of surface has a finite number of openings, whereas a porous surface has an almost infinite number of smaller openings for the coolant flow. The investigation showed that a blade made of sheet-metal laminations stacked on a support member that passed up through the coolant passage was completely unsatisfactory because of extremely poor coolant flow distribution over the blade surface. The flow distribution for two wire-wound blades was more uniform, but the pressure drop between the coolant supply pressure and the local pressure on the outside of the blades was too low by a factor ranging from 3 to 3.5 for the required coolant flow rates. The pressure drop could be increased by forcing the wires closer together during blade fabrication.

Esger, Jack B.↗
NASA NTRS2012

Application of Out-of-Plane Warping to Control Rotor Blade Twist

The goal of this ongoing study is to develop and demonstrate the feasibility of a blade actuation system to dynamically change the twist, and/or the camber, of an airfoil section and, consequently, alter the in-flight aerodynamic loading on the blade for efficient flight control. The required analytical and finite element tools are under development to enable an accurate and comprehensive aeroelastic assessment of the current Full-Blade Warping and 3D Warping Actuated Trailing Edge Flap concepts. The feasibility of the current concepts for swashplateless rotors and higher harmonic blade control is also being investigated. In particular, the aim is to complete the following objectives, some of which have been completed (as noted below) and others that are currently ongoing: i) Develop a Vlasov finite element model and validate against the ABAQUS shell models (completed). ii) Implement the 3D warping actuation concept within the comprehensive analysis code DYMORE. iii) Perform preliminary aeroelastic simulations of blades using DYMORE with 3D warping actuation: a) Investigate the blade behavior under 1 per/rev actuation. Determine whether sufficient twist can be generated and sustained to achieve primary blade control. b) Investigate the behavior of a trailing edge flap configuration under higher harmonic excitations. Determine how much twist can be obtained at the harmonics 2-5 per/rev. iv) Determine actuator specifications such as the power required, load and displacements, and identify the stress and strain distributions in the actuated blades. In general, the completion of Item ii) above will give an additional research capability in rotorcraft dynamics analyses, i.e., the capability to calculate the rotor blade twist due to warping, something that is not currently available in any of the existing comprehensive rotorcraft analyses.

VanWeddingen, Yannick↗
NASA NTRS2014

Optimization of an Active Twist Rotor Blade Planform for Improved Active Response and Forward Flight Performance

A study was conducted to identify the optimum blade tip planform for a model-scale active twist rotor. The analysis identified blade tip design traits which simultaneously reduce rotor power of an unactuated rotor while leveraging aeromechanical couplings to tailor the active response of the blade. Optimizing the blade tip planform for minimum rotor power in forward flight provided a 5 percent improvement in performance compared to a rectangular blade tip, but reduced the vibration control authority of active twist actuation by 75 percent. Optimizing for maximum blade twist response increased the vibration control authority by 50 percent compared to the rectangular blade tip, with little effect on performance. Combined response and power optimization resulted in a blade tip design which provided similar vibration control authority to the rectangular blade tip, but with a 3.4 percent improvement in rotor performance in forward flight.

Sekula, Martin K↗
NASA NTRS1960

Shock Losses in Transonic Compressor Blade Rows

The rather extensive study of the shock losses in transonic compressors can he summarized by the following remarks: 1. A simple flow model can be used to estimate shock losses at the design point for transonic compressor blade rows and results iii reasonable correlation of loss data. It is indicated that shock losses can constitute a sizable portion of the total losses in it transonic compressor rotor. This includes all blade elements at which sonic or higher relative velocities are obtained. 2. Shock losses can he shown to exist across the blade passage (free-stream loss) and by the method of superposition with the blade profile losses result in an estimated design total loss coefficient. 3. The shock configuration was experimentally determined by the rapid pressure rise between the blades as measured by the use of barium titanate crystals. At the minimum loss operating conditions the shock is very similar to that assumed in the simple How model. 4. Shock losses obtained from a more detailed flow model were compared with the losses obtained by the simple flow model. Measured loss distribution from blade to blade closely approaches the analytical shock loss distribution. The measured distribution shows the effect of a shock boundary layer interaction. 5. The analytical method (from the detailed flow model) of determining the shock location ahead of the blade seems to apply reasonably well over a range of incidence angles. The analytical shock losses do not vary a great deal with blade element incidence angles.

Miller, Genevieve R.↗
NASA NTRSDate not supplied

Blade Displacement Measurements of a Rotor in Forward Flight in the Langley 14- by 22-Ft Wind Tunnel

Stereo photogrammetry was used to measure the elastic bending and twist of a three-bladed rotor in forward flight in the NASA Langley 14-by 22-Ft Subsonic Wind Tunnel. The rotor was imaged from below by two cameras mounted at windows of a large turntable in the floor of the test section. At each test condition, the turntable and cameras were rotated and the cameras were triggered to allow measurements over a range of blade azimuth angles. Retro-reflective targets were applied along the leading and trailing edges of the lower surface of each blade. Image blur due to blade motion was minimized by illuminating the targets with high-intensity LED flash lamps mounted next to each camera. The cameras were re-calibrated at each angular position of the turntable using the positions in each image of retro-reflective targets on the ceiling of the test section whose spatial coordinates had been very accurately measured. The blade displacement measurements yielded elastic bending and twist along each blade as functions of blade azimuth, thrust coefficient, and advance ratio, all at a constant rotor angle-of-attack. In addition, the measurements produced estimates of the rigid-body blade pitch, flap, and lag angles.

rotor blade displacement↗
NASA NTRSDate not supplied

Blade Displacement Measurements of a Rotor in Forward Flight in the Langley 14-by 22-Foot Wind Tunnel

Stereo photogrammetry was used to measure the elastic bending and twist of a three-bladed rotor in forward flight in the NASA Langley 14-by 22-Ft Subsonic Wind Tunnel. The rotor was imaged from below by two cameras mounted at windows of a large turntable in the floor of the test section. At each test condition, the turntable and cameras were rotated and the cameras were triggered to allow measurements over a range of blade azimuth angles. Retro-reflective targets were applied along the leading and trailing edges of the lower surface of each blade. Image blur due to blade motion was minimized by illuminating the targets with high-intensity LED flash lamps mounted next to each camera. The cameras were re-calibrated at each angular position of the turntable using the positions in each image of retro-reflective targets on the ceiling of the test section whose spatial coordinates had been very accurately measured. The blade displacement measurements yielded elastic bending and twist along each blade as functions of blade azimuth, thrust coefficient, and advance ratio, all at a constant rotor shaft angle. In addition, the measurements produced estimates of the rigid-body blade pitch, flap, and lag angles.

rotor↗
NASA NTRSDate not supplied

Structural Design and Aeromechanical Analysis of Unconventional Blades for Future Mars Rotorcraft

The structural design for rotor blades with thin, unconventional airfoils for Earth-based testing is obtained using three-Dimensional (3D) aeromechanical analysis. This analysis is in support of the NASA ROAMX project. The outer mold was provided by NASA, but the internal structural design was developed at the University of Maryland and is presented here, along with a thorough aeromechanical analysis. The main objectives are to verify the structural integrity of the design and understand the unique aeroelastic behavior of the non-conventional airfoils designed for low-Reynolds number and high-Mach number flow. Six different blade models are considered, with the pitch axis varied from quarter-chord to mid-chord to determine the effect of C.G. offset on natural frequencies, blade deformations, root loads, and 3D stresses. All six blade designs are first studied under rotation in pure vacuum, and significant reductions in root loads and 3D stresses are achieved by moving the pitch axis closer to mid-chord to reduce the C.G. offset. Based on the vacuum analysis, the blade design with the pitch axis at 40% chord is selected for aerodynamic analysis. The blade control load, airloads, deformations, and 3D stresses are studied for steady hover. Dynamic control load and dynamic 3D stresses are studied for unsteady hover achieved using cyclic. Significant elastic twist is observed due to the trapeze effect and propeller moment, affecting the spanwise distribution of aerodynamic loads on the blades. However, the effect of aerodynamic loads on 3D stresses and the blade control load is found to be minimum. The dynamic control load is found to increase significantly due to inertial coupling from the C.G. offset. The dynamic stresses also increase, although still have factors of safety greater than two for both tensile and compressive stress.

Structural Design↗
NASA NTRS1948

Cooling of gas turbines IX : cooling effects from use of ceramic coatings on water-cooled turbine blades

The hottest part of a turbine blade is likely to be the trailing portion. When the blades are cooled and when water is used as the coolant, the cooling passages are placed as close as possible to the trailing edge in order to cool this portion. In some cases, however, the trailing portion of the blade is so narrow, for aerodynamic reasons, that water passages cannot be located very near the trailing edge. Because ceramic coatings offer the possibility of protection for the trailing part of such narrow blades, a theoretical study has been made of the cooling effect of a ceramic coating on: (1) the blade-metal temperature when the gas temperature is unchanged, and (2) the gas temperature when the metal temperature is unchanged. Comparison is also made between the changes in the blade or gas temperatures produced by ceramic coatings and the changes produced by moving the cooling passages nearer the trailing edge. This comparison was made to provide a standard for evaluating the gains obtainable with ceramic coatings as compared to those obtainable by constructing the turbine blade in such a manner that water passages could be located very near the trailing edge.

HEAT TRANSMISSION - METALS↗
NASA NTRS1973

Rotating-blade vortex noise

An experimental investigation has been made of the Langley full-scale tunnel and outdoors to investigate some of the characteristics of vortex noise generated on a rotating-blade system. Acoustic measurements were made at several microphone positions for two different blade sections with several tip shapes and spoiler configurations. The blades were operated only at zero lift at each radial station, both for operating in their own wake and for operating with the wake blown downstream. Rotors with cylindrical blades generally created more noise throughout the noise spectrum than the rotor with NACA 0012 blades. Blowing the shed wake from the rotor with cylindrical blades did not have an appreciable effect on the frequency-amplitude spectrum. The tip shape changes had very little effect on the frequency-amplitude spectrum of the noise. Spoilers applied to the rotor with NACA 0012 blades increased the amplitude of the spectrum and decreased the number of harmonics of blade passage frequency.

Scheiman, J.↗
NASA NTRS1974

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors, part 8

An experimental investigation was conducted with an 0.8 hub/tip ratio, single-stage, axial flow compressor to determine the potential of tandem-airfoil blading for improving the efficiency and stable operating range of compressor stages. The investigation included testing of a baseline stage with single-airfoil blading and two tandem-blade stages. The overall performance of the baseline stage and the tandem-blade stage with a 20-80% loading split was considerably below the design prediction. The other tandem-blade stage, which had a rotor with a 50-50% loading split, came within 4.5% of the design pressure rise (delta P(bar)/P(bar) sub 1) and matched the design stage efficiency. The baseline stage with single-airfoil blading, which was designed to account for the actual rotor inlet velocity profile and the effects of axial velocity ratio and secondary flow, achieved the design predicted performance. The corresponding tandem-blade stage (50-50% loading split in both blade rows) slightly exceeded the design pressure rise but was 1.5 percentage points low in efficiency. The tandem rotors tested during both phases demonstrated higher pressure rise and efficiency than the corresponding single-airfoil rotor, with identical inlet and exit airfoil angles.

Brent, J. A.↗
NASA NTRS1975

Laser velocimeter measurements of rotor blade loads and tip vortex rollup

A method for obtaining and analyzing the instantaneous velocities of helicopter rotor flow fields through use of a laser velocimeter capable of simultaneously sensing two components of velocity is described. Rotor blade aerodynamic loads may be computed from the velocity distributions near the blades. The experiment was conducted with a 2.13 m (7 ft) diameter model helicopter rotor operating in a wind tunnel. Velocity distributions are presented which document the flow field near the advancing blade. Circulation is calculated from the velocity measurements, and the radial distribution of circulation is discussed. The influence of the tip vortex from the preceding blade is apparent in this distribution. Tip vortex rollup on the advancing blade was documented by making a series of measurements at various distances behind the blade. Effects of blade drag are evident in the velocities behind the blade trailing edge.

Biggers, J. C.↗
NASA NTRS1977

FORTRAN program for calculating leading and trailing-edge geometry of turbomachine blades

A FORTRAN IV program which calculates leading- and trailing-edge circle radii, tangency angles on the leading- and trailing-edge circles, and stagger angles of turbomachinery blade sections using only spline points defining the blade surfaces is described. The program shifts the origin of the blade coordinates to the leading edge of the blade. Required input includes (m, theta) coordinates of a sufficient number of spline points to adequately define the two surfaces of the blade. Other required input are the radii from the axis of rotation of the leading- and trailing-edges. The output from this program is used directly as the geometrical input for a NASA developed program for calculating transonic velocities on a blade-to-blade stream surface of a turbomachine. The program is used for axial, radial, and mixed flow turbomachine blades.

Schumann, L. F.↗
NASA NTRS1976

A critical examination of the flap-lag dynamics of helicopter rotor blades in hover and in forward flight

A critical examination of flap-lag stability of a centrally hinged, spring-restrained rigid blade in both hover and forward flight is presented. Several differences in the equations of motion for blade flap-lag stability in the existing literature are identified. A rigorous and systematic development of these equations for a rigid articulated blade in forward flight shows the existence of some linear aerodynamic coupling terms associated with blade steady-state flapping and lagging in the perturbation equations. The differences identified are shown to be associated with the order in which the flap and lag transformations are taken in developing the equations of motion. The implications of these differences on stability are examined, and it is shown that the pitch-lag coupling terms associated with a flap-lag hinge transformation sequence have a marked influence on flap-lag stability. Some qualitative considerations on the role of the assumed transformation sequence in the development of the flap-lag equations for a hingeless elastic blade are also given. On the basis of these considerations, it is shown that aerodynamic coupling terms associated with blade steady-state flapping and lagging similar to those found for the rigid blade will also appear in the equations for the elastic blade.

Kaza, K. R. V.↗
NASA NTRS1977

Containment of composite fan blades

The development of containment concepts for use with large composite fan blades, taking into account the frangible nature of composite blades is considered. Aspects of the development program include; (1) an analysis to predict the interaction between a failed fan blade and the blade containment structure; (2) scaling factors to allow impact testing using subscale containment rings and simulated blades; (3) the design and fabrication of containment systems for further evaluation in a rotating rig test facility; (4) evaluate the test data against the analytically predicted results; and (5) determine overall systems weights and design characteristics of a composite fan stage installation and compare to the requirements of an equivalent titanium fan blade system. Progress in the blade impact penetration tests and the design and fabrication of blade containment systems is reported.

Coppa, A. P.↗
NASA NTRS1975

Quiet Clean Short-haul Experimental Engine (QCSEE) under-the-wing engine composite fan blade design

The design and analysis of a composite fan blade for the under the wing (UTW) QCSEE is presented. The blade is designed for a variable pitch, 18 bladed rotor and is constructed from a hybrid composite combination of materials consisting of Kevlar-49, type AS graphite, boron, and S-glass fibers in a PR288 epoxy resin matrix. The blade has an attached platform which is constructed of AS-graphite, PR288 epoxy resin matrix and aluminum honeycomb. The blade is designed to satisfy aerostability and cyclic life and strength requirements with a light weight construction. The attached platform is designed for a fail-safe condition in that it is retainable by the blade, under centrifugal force loading, even in the event of blade to platform bond separation. Details of the blade design and the results of stress, vibration, and impact analysis are included.

Source record↗
NASA NTRS1980

Experimental study of low aspect ratio compressor blading

The paper presents a study of low aspect blading for the inlet stages of a high pressure ratio, high-speed core compressor. The basic overall design variables were stage pressure ratio and blade aspect ratio; these four stages represent two levels of total pressure ratio, two levels of rotor blade aspect ratio, and two levels of stator vane aspect ratios. Comparisons of the overall performance, radial distributions of performance parameters, diffusion factors at the near-stall conditions, blade element data, and the axial distribution of rotor tip static pressures yielded the following results: (1) higher peak pressure ratio, high stage and rotor efficiencies, and greater stall margin were obtained with the lower aspect ratio blading, (2) the lower aspect ratio blading showed improved performance over the entire blade span, and (3) the lower aspect ratio rotors operated at higher diffusion factors and higher incidence angles over the entire blade span.

Reid, L.↗
NASA NTRS1948

Icing and De-Icing of a Propeller with Internal Electric Blade Heaters

An investigation has been made in the NACA Cleveland icing research tunnel to determine the de-icing effectiveness of an experimental configuration of an Internal electric propeller-blade heater. Two atmospheric Icing conditions and two propeller operating conditions were Investigated, In experiments with unheated blades and with heat applied to the blades both continuously and cyclically. Data are presented to show the effect of propeller speed., ambient air temperature and liquid-water concentration, and the duration of the heat-on and cycle times on the power requirements and de-Icing performance of the blade heaters. The extent of ice-covered area on the blades for various icing ax4 operating conditions has been determined. The largest iced area was obtained at the higher ambient-air temperatures and at low propeller speed. The ohord.wise extent of Icing In practically every case was greater than that covered by blade heaters. Adequate de-icing in the heated area with continuous application of heat was obtained with the power available but a maximum power, input of 1250 watts per blade was insufficient for cyclic de-Icing for the range of conditions investigated. Blade-surface temperature rates of rise of 0.2 to 0.7 F per second were obtained and the minimum cooling period for cyclic de-icing was found to be approximately 2-1/2 times the heating period.

Lewis, James P.↗