Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wind shear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Virtual Flight Demonstration of the Stratospheric Dual-Aircraft Platform

A baseline configuration for the dual-aircraft platform (DAP) concept is described and evaluated in a physics-based flight dynamics simulations for two month-long missions as a communications relay in the lower stratosphere above central Florida, within 150-miles of downtown Orlando.The DAP configuration features two large glider-like (130 ft wing span) unmanned aerial vehicles connected via a long adjustable cable (total extendible length of 3000 ft) which effectively sail without propulsion using available wind shear. Use of onboard LiDAR wind profilers to forecast wind distributions are found to be necessary to enable the platform to efficiently adjust flight conditions to remain sailing by finding sufficient wind shear across the platform. The aircraft derive power from solar cells, like a conventional solar aircraft, but also extract wind power using the propeller as a turbine when there is an excess of wind shear available.Month-long atmospheric profiles (at 3-5 min intervals) in the vicinity of 60,000-ft are derived from archived data measured by the 50-Mhz Doppler Radar Wind Profiler at Cape Canaveral and used in the DAP flight simulations. A cursory evaluation of these datasets show that sufficient wind shear for DAP sailing is persistent, suggesting that DAP could potentially sail over 90% of the month-long durations even when limited by modest ascent/descent rates.DAP's novel guidance software uses a non-linear constrained optimization technique to define waypoints such that sailing mode of flight is maintained where possible, and minimal thrust is required where sailing is not practical. A set of constraints are identified which result in waypoints that enable efficient flight (i.e., minimal use of propulsion) over the two month-long flight simulations. Waypoint solutions may need to be tabulated for a wide range of potential atmospheric conditions and stored onboard for quick retrieval on a real DAP.DAP's flight control software uses an unconventional mixture of spacecraft and aircraft control techniques. Flight simulations confirms that this controls approach enables the platform to consistently reach successive waypoints over the month-long flight simulations.The ability of DAP to transition between the sailing mode (i.e., cable tension is high) and standard formation flight (i.e., cable tension is low) is a vital capability (e.g., to enable intermittent turns while stationkeeping). A new method to perform these transitions has been identified and characterized with flight simulation which requires special aircraft modifications.The energy-usage of the DAP configuration during two month-long stationkeeping missions over central Florida (i.e., stationkeeping over Orlando) is evaluated and compared to that of a pure solar aircraft of the same weight and aerodynamic performance. DAP is shown to consistently reduce net propulsion usage while simultaneously increasing solar energy capture.A baseline 700 GHz communications system is described and its performance evaluated for the proposed mission over central Florida. It is found that the variable roll orientation of the aircraft would increase the power required to maintain coverage over the stationkeeping radius of 150 miles (e.g., by as much as 100% when DAP is 150 miles from Orlando), compared to level flight. This effect can be mitigated via additional antenna design complexity or a more restricted stationkeeping radius.

Demonstrations↗

Magnitude and frequency of wind speed shears and associated downdrafts

Data are presented indicating the frequency of occurrence of wind shear and downdrafts together with information on the simultaneous occurrence of these two phenomena. High resolution wind profile measurements recorded at a 150 meter ground winds tower facility were used for the analysis. From instantaneous measurements during horizontal wind speeds of gale-force and below intensity, vertical motion at the 10, 60, and 150 m levels was approximately 60 percent downward and 40 percent upward. At the 18 level the percentages were reversed. Updraft maxima were an order of magnitude or two greater than downdrafts at all levels. Frequency of vertical motion or = 9.7 kts for a year at four levels was 338 occurrences upward and 274 downward. Approximately 90 percent of these updrafts occurred at the 18 m level almost equally during summer and winter, and 65 percent of the downdrafts were at the 150 m level during summer.

Alexander, M. B.↗

Flight test operations

Flight test operations concerning the Joint NASA/FAA Airborne Wind Shear Detection and Avoidance Program 1991 Flight Experiments are presented in viewgraph form and include the following: research aircraft sensor installations; wind shear reactive sensor operation; wind shear IR sensor operation; wind shear radar sensor operation; wind shear lidar sensor operation; and 1991 flight test summary.

Lewis, Michael S.↗

Environmental sensitivities of shallow-cumulus dilution – Part 2: Vertical wind profile

This second part of a numerical study on shallow-cumulus dilution focuses on the sensitivity of cloud dilution to changes in the vertical wind profile. Insights are obtained through large-eddy simulations of maritime and continental cloud fields. In these simulations, the speed of the initially uniform geostrophic wind and the strength of geostrophic vertical wind shear in the cloud and subcloud layer are varied. Increases in the cloud-layer vertical wind shear (up to 9 ms -1 km -1 ) lead to 40%–50% larger cloud-core dilution rates compared to their respective unsheared counterparts. When the background wind speed, on the other hand, is enhanced by up to 10 ms -1 and subcloud-layer vertical wind shear develops or is initially prescribed, the dilution rate decreases by up to 25%. The sensitivities of the dilution rate are linked to the updraft strength and the properties of the entrained air. Increases in the wind speed or vertical wind shear result in lower vertical velocities across all sets of experiments with stronger reductions in the cloud-layer wind shear simulation (27%–47%). Weaker updrafts are exposed to mixing with the drier surrounding air for a longer time period, allowing more entrainment to occur (i.e., the “core-exposure effect”). However, reduced vertical velocities, in concert with increased cloud-layer turbulence, also assist in widening the humid shell surrounding the cloud cores, leading to entrainment of more humid air (i.e., the “core–shell dilution effect”). In the experiments with cloud-layer vertical wind shear, the core-exposure effect dominates and the cloud-core dilution increases with increasing shear. Conversely, when the wind speed is increased and subcloud-layer vertical wind shear develops or is imposed, the core–shell dilution effect dominates to induce a buffering effect. The sensitivities are generally stronger in the maritime simulations, where weaker sensible heat fluxes lead to narrower, more tilted, and, therefore, more suppressed cumuli when cloud-layer shear is imposed. Moreover, in the experiments with subcloud wind shear, the weaker baseline turbulence in the maritime case allows for a larger turbulence enhancement, resulting in a widening of the transition zones between the cores and their environment, leading to the entrainment of more humid air.

54 ENVIRONMENTAL SCIENCES↗

Integrated display of multi-sensor geophysical and electromagnetic flight data

Low-altitude wind shear has been identified by several aviation interests as a significant hazard to the safety of flying. The hazard may be greatest when the wind shear is due to an unpredicted and short-lived microburst occurring in the immediate flight path of an aircraft during takeoff or landing. Researchers from the NASA Langley Research Center have investigated wind shear by developing a suite of remote sensing instruments and then using these instruments in an airborne wind shear detection flight program. Among these instruments were a Doppler radar, a lidar, and an infrared sensor; these were supported by in situ measurements of aircraft and environmental parameters and by ground-based Doppler radars. The basic problem addressed was the airborne detection and measurement of meteorologically-induced wind shear sufficiently ahead of the aircraft to allow avoidance. If the remote measurements of the shear and its associated radar reflectivity did not exceed set limits, the airplane then continued through the wind shear so that in situ measurements could be made for comparison. Initial detection and vectoring to the wind shear was normally given from a ground-based Doppler weather radar and most of the wind shear events were due to microbursts, both wet and dry. This paper considers the problems of sampling the wind shear event, time and space registration among the various sensors, coordination of the various sensors' beams and sampling volumes, and also various techniques for portraying the data, both for research and for presentation. Examples are given based on data from the 1991 and 1992 NASA/FAA wind shear flights, and the results and conclusions are generalized to other flight experiments involving multi-sensor electromagnetic data sets.

Delnore, V. E.↗

Comparison of the Dispersion of the Mt. Pinatubo and El Chichon Stratospheric Aerosol Clouds

Insights into stratospheric transport and the climatic effects of large volcanic eruptions can be obtained by studying the dispersion of two of the largest volcanic eruptions this century, Mt. Pinatubo and El Chichon. Although both eruptions were located between 15 and 20 N latitude, and occurred either in spring or early summer (April vs June), the two volcanic clouds evolved differently in terms of dispersion of the volcanic aerosols. The El Chichon cloud stayed essentially confined to between 30 N and the equator until fall season following the eruption, whereas the Mt. Pinatubo cloud spread more rapidly into the southern hemisphere. Three dimensional stratospheric interactive tracer simulations for the particular years of the eruptions are reported. Radiative heating of the volcanic clouds due to upwelling IR radiation from the troposphere is important for understanding the dispersion of the volcanic aerosols, especially for Mt. Pinatubo. However, radiative heating alone does not explain the qualitative difference in meridional dispersion of the two volcanic clouds. The rate at which the aerosol clouds are sheared apart by wind shear limits the effectiveness of the radiative heating in producing meridional dispersion, and the wind shear is a function of the particular year of each eruption.

Young, R. E.↗

Analysis of low-altitude wind speed and direction shears

Horizontal wind profile measurements recorded at the NASA 150-Meter Ground Winds Tower Facility at the Kennedy Space Center, Fla., are analyzed to evaluate wind shears known to be hazardous to the ascent and descent of conventional aircraft and the Space Shuttle. Twenty 5-s intervals of high (between 10 and 18 m/s) and gale force (18 to 33 m/s) surface winds provided instantaneous recordings every 0.1 s per speed, direction, and tower level from 3-150 m. Mathematical (maximum, mean, standard deviation) and graphical (percentage frequency distribution) descriptions of absolute, positive, and negative speed and direction shears with altitude (six vertical layers) and along flight path (one horizontal distance) are presented as functions of the intensity categories and significant values.

Alexander, M. B.↗

Quasi-Equilibrium States in the Tropics Simulated by a Cloud-Resolving Model: Specific Features and Budget Analysis - Part 1

A series of long-term integrations using the two-dimensional Goddard Cumulus Ensemble (GCE) model were performed by altering imposed environmental components to produce various quasi-equilibrium thermodynamic states. Model results show that the genesis of a warm/wet quasi-equilibrium state is mainly due to either strong vertical wind shear (from nudging) or large surface fluxes (from strong surface winds), while a cold/dry quasi-equilibrium state is attributed to a remarkably weakened mixed-wind shear (from vertical mixing due to deep convection) along with weak surface winds. In general, latent heat flux and net large-scale temperature forcing, the two dominant physical processes, dominate in the beginning stage of the simulated convective systems, then considerably weaken in the final stage, which leads to quasi-equilibrium states. A higher thermodynamic regime is found to produce a larger rainfall amount, as convective clouds are the leading source of rainfall over stratiform clouds even though the former occupy much less area. Moreover, convective clouds are more likely to occur in the presence of strong surface winds (latent heat flux), while stratiform clouds (especially the well-organized type) are favored in conditions with strong wind shear (large-scale forcing). The convective systems, which consist of distinct cloud types due to the variation in horizontal winds, are also found to propagate differently. Accordingly, convective systems with mixed-wind shear generally propagate in the direction of shear, while the system with strong (multidirectional) wind shear propagates in a more complex way. Based on the results from the temperature (Q1) and moisture (Q2) budgets, cloud-scale eddies are found to act as a hydrodynamic 'vehicle' that cascades the heat and moisture vertically. Several other specific features such as atmospheric stability, CAPE, and mass fluxes are also investigated and found to be significantly different between diverse quasi-equilibrium states. Detailed comparisons between the various states are presented.

Shie, C.-L.↗

Winds aloft statistical analysis in support of day of launch Shuttle systems evaluation

In connection with the development of the Meteorological Interactive Data Display System (MIDDS) for utilization by the Launch Systems Evaluation Advisory Team (LSEAT), requirements have been established to expand the pre-launch analysis of winds aloft for the Space Shuttle. Statistical analyses developed for the system include: comparison of pre-launch wind component profiles to wind component extremes at each altitude calculated from launch site historical data; conditional probability ellipses for wind vectors at a future time given the wind vector at an initial time; comparison of observed extreme wind shear and associated wind speed with launch site historical data utilizing the bivariate extreme value (Gumbel) distribution; estimation of extremes of wind speed or wind shear at a future time given the extremes of either variable at an initial time, utilizing the conditional extreme value distribution; power spectrum analysis for tracking wind perturbation energy in sequential pre-launch Jimsphere wind profiles.

Adelfang, S. I.↗

NASA/LMSC coherent LIDAR airborne shear sensor: System capabilities and flight test plans

The primary objective of the NASA/LMSC Coherent Lidar Airborne Shear Sensor (CLASS) system flight tests is to evaluate the capability of an airborne coherent lidar system to detect, measure, and predict hazardous wind shear ahead of the aircraft with a view to warning flight crew of any impending dangers. On NASA's Boeing 737 Transport Systems Research Vehicle, the CLASS system will be used to measure wind velocity fields and, by incorporating such measurements with real-time aircraft state parameters, identify regions of wind shear that may be detrimental to the aircraft's performance. Assessment is to be made through actual wind shear encounters in flight. Wind shear measurements made by the class system will be compared to those made by the aircraft's in situ wind shear detection system as well as by ground-based Terminal Doppler Weather Radar (TDWR) and airborne Doppler radar. By examining the aircraft performance loss (or gain) due to wind shear that the lidar predicts with that actually experienced by the aircraft, the performance of the CLASS system as a predictive wind shear detector will be assessed.

Robinson, Paul↗

Wind Shear/Turbulence Inputs to Flight Simulation and Systems Certification

The purpose of the workshop was to provide a forum for industry, universities, and government to assess current status and likely future requirements for application of flight simulators to aviation safety concerns and system certification issues associated with wind shear and atmospheric turbulence. Research findings presented included characterization of wind shear and turbulence hazards based on modeling efforts and quantitative results obtained from field measurement programs. Future research thrusts needed to maximally exploit flight simulators for aviation safety application involving wind shear and turbulence were identified. The conference contained sessions on: Existing wind shear data and simulator implementation initiatives; Invited papers regarding wind shear and turbulence simulation requirements; and Committee working session reports.

Bowles, Roland L.↗

Atmospheric Constraints on Landing Site Selection

The Martian atmosphere is a significant part of the environment that the Mars Exploration Rovers (MER) will encounter. As such, it imposes important constraints on where the rovers can and cannot land. Unfortunately, as there are no meteorological instruments on the rovers, there is little atmospheric science that can be accomplished, and no scientific preference for landing sites. The atmosphere constrains landing site selection in two main areas, the entry descent and landing (EDL) process and the survivability of the rovers on the surface. EDL is influenced by the density profile and boundary layer winds (up to altitudes of 5 to 10 km). Surface survivability involves atmospheric dust, temperatures and winds. During EDL, the atmosphere is used to slow the lander down, both ballistically and on the parachute. This limits the maximum elevation of the landing site to -1.3 km below the MOLA reference aeroid. The landers need to encounter a sufficiently dense atmosphere to be able to stop, and the deeper the landing site, the more column integrated atmosphere the lander can pass through before reaching the surface. The current limit was determined both by a desire to be able to reach the hematite region and by a set of atmosphere models we developed for EDL simulations. These are based on Thermal Emission Spectrometer (TES) atmospheric profile measurements, Ames Mars General Circulation Model (MGCM) results, and the 1-D Ames GCM radiative/convective model by J. Murphy. The latter is used for the near surface diurnal cycle. The current version of our model encompasses representative latitude bands, but we intend to make specific models for the final candidate landing sites to insure that they fall within the general envelope. The second constraint imposed on potential landing sites through the EDL process is the near surface wind. The wind in the lower approximately 5 km determines the horizontal velocity that the landers have when they land. Due to the mechanics of the landing process, the total velocity (including both the horizontal and vertical components) determines whether or not the landers are successful. Unfortunately, the landing system has no easy way to nullify any horizontal velocity imparted by the wind, so the landing sites selected need to have as little wind as possible. In addition to the mean wind velocity, the landing system is sensitive to vertical wind shear in the lowest kilometer or so. Wind shear can deflect the retro rockets (RADs) from their nominal vertical orientation producing unwanted horizontal spacecraft velocities. Both mean velocity and wind shear are dominated by the the local topography and other surface properties (in particular albedo and thermal inertia which control the surface temperature). This is seen even in simplified 2-D mesoscale models. The effects in a fully 3-D model are expected to he even more topographically dependent. In particular there is potential for wind channeling in canyons and other terrain features. Boundary layer winds and wind shear are currently being modeled based on terrestrial data and boundary layer scaling laws modified for Martian conditions. We hope to supplement this with mesoscale model results (from several sources) once the number of landing sites is reduced to a manageable number.

Kass, David M.↗

Cockpit display of hazardous weather information

Information transfer and display issues associated with the dissemination of hazardous weather warnings are studied in the context of wind shear alerts. Operational and developmental wind shear detection systems are briefly reviewed. The July 11, 1988 microburst events observed as part of the Denver Terminal Doppler Weather Radar (TDWR) operational evaluation are analyzed in terms of information transfer and the effectiveness of the microburst alerts. Information transfer, message content and display issues associated with microburst alerts generated from ground based sources (Doppler Radar, Low Level Wind Shear Alert System, and Pilot Reports) are evaluated by means fo pilot opinion surveys and part task simulator studies.

Hansman, R. John, Jr.↗

Effect of shear on aircraft landing

A simulation study was conducted to determine the effect of wind shear on aircraft landings. The landing of various type of commercial and military aircraft was digitally simulated starting from an initial altitude of 300 feet. Assuming no pilot feedback during descent, the deviation in touchdown point due to vertical profiles of wind shear was determined. The vertical profiles of wind shear are defined in terms of surface roughness, Z sub 0, and stability, L, parameters. The effects on touchdown due to Z sub 0 and L have been calculated for the different type aircraft. Comparisons were made between the following types of aircraft: (1) C-130E, (2) C-135A, (3) C-141, (4) DC-8, (5) Boeing 747, and (6) an augmentor-wing STOL. In addition, the wind shear effect on touchdown resulting from different locations of the center of gravity and gross weights was also analyzed.

Luers, J. K.↗

Pseudo-wavelet analysis of turbulence patterns in three vegetation layers

Ramp patterns in scalar traces such as temperature are the signature of coherent structures. A pseudo-wavelet analysis technique was developed in which ideal saw-tooth patterns of varying size were used as basis functions and fitted to temperature and velocity data. Data recorded from three very different vegetation stands were examined in this study. It was found that the most probable structure duration for the forest canopy was in the range 35-40 s, for the orchard canopy it was 20-25 s and for the maize it was 15-20 s. When expressed in non-dimensional form, the structure duration probability distribution for the maize canopy was about a decade larger than for the forest canopy, with the orchard canopy intermediate. The mean eddy duration versus wind shear relation falls on a narrow band for all three canopies, indicating that wind shear at the canopy top is the determining factor for the scale of the coherent eddies. The inverse of duration and intermittency of coherent structures exhibits a tendency of independence from wind shear at higher wind shear values. Coherent structures transport heat in a more efficient way than do smaller scale, less coherent motions. In all the canopies, the heat flux fractions associated with coherent structures are at least 10% higher than the corresponding time fraction.

Qiu, Jie↗

Simulator systems integration

The implementation of available wind shear data into general aviation flight training simulators is discussed. Currently, there are 11 simulators with wind shear models installed involving some 9 different aircraft models. Retrofits to other systems that were put out earlier are currently underway, and all the new simulators will have wind shear available for the instructors to use for demonstrations and training. There are three types of computer systems involved, and two different types of instructor stations. Most of the systems with wind shear are the CRT-type displays. The integration of wind shear models in flight simulators is discussed in detail.

Shipman, Keith W.↗

Various Numerical Applications on Tropical Convective Systems Using a Cloud Resolving Model

In recent years, increasing attention has been given to cloud resolving models (CRMs or cloud ensemble models-CEMs) for their ability to simulate the radiative-convective system, which plays a significant role in determining the regional heat and moisture budgets in the Tropics. The growing popularity of CRM usage can be credited to its inclusion of crucial and physically relatively realistic features such as explicit cloud-scale dynamics, sophisticated microphysical processes, and explicit cloud-radiation interaction. On the other hand, impacts of the environmental conditions (for example, the large-scale wind fields, heat and moisture advections as well as sea surface temperature) on the convective system can also be plausibly investigated using the CRMs with imposed explicit forcing. In this paper, by basically using a Goddard Cumulus Ensemble (GCE) model, three different studies on tropical convective systems are briefly presented. Each of these studies serves a different goal as well as uses a different approach. In the first study, which uses more of an idealized approach, the respective impacts of the large-scale horizontal wind shear and surface fluxes on the modeled tropical quasi-equilibrium states of temperature and water vapor are examined. In this 2-D study, the imposed large-scale horizontal wind shear is ideally either nudged (wind shear maintained strong) or mixed (wind shear weakened), while the minimum surface wind speed used for computing surface fluxes varies among various numerical experiments. For the second study, a handful of real tropical episodes (TRMM Kwajalein Experiment - KWAJEX, 1999; TRMM South China Sea Monsoon Experiment - SCSMEX, 1998) have been simulated such that several major atmospheric characteristics such as the rainfall amount and its associated stratiform contribution, the Qlheat and Q2/moisture budgets are investigated. In this study, the observed large-scale heat and moisture advections are continuously applied to the 2-D model. The modeled cloud generated from such an approach is termed continuously forced convection or continuous large-scale forced convection. A third study, which focuses on the respective impact of atmospheric components on upper Ocean heat and salt budgets, will be presented in the end. Unlike the two previous 2-D studies, this study employs the 3-D GCE-simulated diabatic source terms (using TOGA COARE observations) - radiation (longwave and shortwave), surface fluxes (sensible and latent heat, and wind stress), and precipitation as input for the Ocean mixed-layer (OML) model.

Shie, C.-L.↗

Tornadoes in Southeast South America: Mesoscale to Planetary-Scale Environments

Abstract A multiscale analysis of the environment supporting tornadoes in southeast South America (SESA) was conducted based on a self-constructed database of 74 reports. Composites of environmental and convective parameters from ERA5 were generated relative to tornado events. The distribution of the reported tornadoes maximizes over the Argentine plains, while events are rare close to the Andes and south of Sierras de Córdoba. Events are relatively common in all seasons except in winter. Proximity environment evolution shows enhanced instability, deep-layer vertical wind shear, storm-relative helicity, reduced convective inhibition, and a lowered lifting condensation level before or during the development of tornadic storms in SESA. No consistent signal in low-level wind shear is seen during tornado occurrence. However, a curved hodograph with counterclockwise rotation is present. The Significant Tornado Parameter (STP) is also maximized prior to tornadogenesis, most strongly associated with enhanced CAPE. Differences in the convective environment between tornadoes in SESA and the U.S. Great Plains are discussed. On the synoptic scale, tornado events are associated with a strong anomalous trough crossing the southern Andes that triggers lee cyclogenesis, subsequently enhancing the South American low-level jet (SALLJ) that increases moisture advection to support deep convection. This synoptic trough also enhances vertical shear that, along with enhanced instability, sustains organized convection capable of producing tornadic storms. At planetary scales, the tornadic environment is modulated by Rossby wave trains that appear to be forced by convection near northern Australia. Madden–Julian oscillation phase 3 preferentially occurs 1–2 weeks ahead of tornado occurrence. Significance Statement The main goal of this study is to describe what atmospheric conditions (from local to global scales) are present prior to and during tornadic storms impacting southeast South America (SESA). Increasing potential for deep convection, wind shear, and potential for rotating updrafts, as well as reducing convective inhibition and cloud-base height, are predominant a few hours before and during the events in connection to low-level northerly winds enhancing moisture transport to the region. Remote convective activity near northern Australia appears to influence large-scale atmospheric circulation that subsequently triggers convective storms supporting tornadogenesis 1–2 weeks later in SESA. Our findings highlight the importance of accounting for atmospheric processes occurring at different scales to understand and predict tornado occurrences.

Meteorology & Atmospheric Sciences↗