Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WORK FUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Hybrid-mode thermionic converter

Converter's collector electrode has uniform low work-function surface and operates at sufficiently low temperature to produce negligible electron emission. Emitter electrode has main region which has intermediate work-function and auxiliary region which has relatively high work-function surface.

Rasor, N. S.↗

Thermionic noise measurements for on-line dispenser cathode diagnostics for linear beam microwave tubes

A test stand has been set up to measure the current fluctuation noise properties of B- and M-type dispenser cathodes in a typical TWT gun structure. Noise techniques were used to determine the work function distribution on the cathode surfaces. Significant differences between the B and M types and significant changes in the work function distribution during activation and life are found. In turn, knowledge of the expected work function can be used to accurately determine the cathode-operating temperatures in a TWT structure. Noise measurements also demonstrate more sensitivity to space charge effects than the Miram method. Full automation of the measurements and computations is now required to speed up data acquisition and reduction. The complete set of equations for the space charge limited diode were programmed so that given four of the five measurable variables (J, J sub O, T, D, and V) the fifth could be computed. Using this program, we estimated that an rms fluctuation in the diode spacing d in the frequency range of 145 Hz about 20 kHz of only about 10 to the -5 power A would account for the observed noise in a space charge limited diode with 1 mm spacing.

Holland, C.↗

Fermi level pinning induced electrostatic fields and band bending at organic heterojunctions

The energy level alignment at interfaces between organic semiconductors is of direct relevance to understand charge carrier generation and recombination in organic electronic devices. Commonly, work function changes observed upon interface formation are interpreted as interface dipoles. In this study, using ultraviolet and X-ray photoelectron spectroscopy, complemented by electrostatic calculations, we find a huge work function decrease of up to 1.4 eV at the C{sub 60} (bottom layer)/zinc phthalocyanine (ZnPc, top layer) interface prepared on a molybdenum trioxide (MoO{sub 3}) substrate. However, detailed measurements of the energy level shifts and electrostatic calculations reveal that no interface dipole occurs. Instead, upon ZnPc deposition, a linear electrostatic potential gradient is generated across the C{sub 60} layer due to Fermi level pinning of ZnPc on the high work function C{sub 60}/MoO{sub 3} substrate, and associated band-bending within the ZnPc layer. This finding is generally of importance for understanding organic heterojunctions when Fermi level pinning is involved, as induced electrostatic fields alter the energy level alignment significantly.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Top-grid monolayer graphene/Si Schottkey solar cell

Monolayer graphene/Si Schottkey solar cell was fabricated using a top-grid structure. In comparison with the prevailing “top-window” structure, the newly-designed device structure has simplified the fabrication procedures to avoid ultraviolet (UV) photolithography and SiO{sub 2}-eching. We systematically investigated the effect of chemical doping as well as device area on the device performance. It was found that a power conversion efficiency (PCE) of 5.9% can be achieved by engineering the work function of graphene through chemical doping. Our study indicates that top grid structure is suitable to make low-cost, large area and high efficiency graphene/Si Schottkey solar cell. - Graphical abstract: The engineering of the work function of graphene through chemical doping is an effective approach to improve the performance of monolayer graphene/Si Schottky solar cell. - Highlights: • Monolayer graphene/Si Schottkey solar cell was fabricated. • Chemical doping can effectively tune the work function of graphene film. • Chemical doping has significant effect on the device performance. • The top-grid device structure with graphene is promising with low-cost and high efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Low energy electron microscopy and Auger electron spectroscopy studies of Cs-O activation layer on p-type GaAs photocathode

Work function, photoemission yield, and Auger electron spectra were measured on (001) p-type GaAs during negative electron affinity (NEA) surface preparation, surface degradation, and heating processes. The emission current sensitively depends on work function change and its dependence allows us to determine that the shape of the vacuum barrier was close to double triangular. Regarding the NEA surface degradation during photoemission, we discuss the importance of residual gas components the oxygen and hydrogen. We also found that gentle annealing (≤100 °C) of aged photocathodes results in a lower work function and may offer a patch to reverse the performance degradation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Characteristics of ITO films with oxygen plasma treatment for thin film solar cell applications

Graphical abstract: The effect of O{sub 2} plasma treatment on the surface and the work function of ITO films. - Highlights: • ITO films were prepared on the glass substrate by RF magnetron sputtering method. • Effects of O{sub 2} plasma treatment on the properties of ITO films were investigated. • The work function of ITO film was changed from 4.67 to 5.66 eV by plasma treatment. - Abstract: The influence of oxygen plasma treatment on the electro-optical and structural properties of indium-tin-oxide films deposited by radio frequency magnetron sputtering method were investigated. The films were exposed at different O{sub 2} plasma powers and for various durations by using the plasma enhanced chemical vapor deposition (PECVD) system. The resistivity of the ITO films was almost constant, regardless of the plasma treatment conditions. Although the optical transmittance of ITO films was little changed by the plasma power, the prolonged treatment slightly increased the transmittance. The work function of ITO film was changed from 4.67 eV to 5.66 eV at the plasma treatment conditions of 300 W and 60 min.

36 MATERIALS SCIENCE↗

Rotation magnet sputtering: Damage-free novel magnetron sputtering using rotating helical magnet with very high target utilization

Novel magnetron-sputtering equipment, called rotation magnet sputtering (ROT-MS), was developed to overcome various disadvantages of current magnetron-sputtering equipment. Disadvantages include (1) very low target utilization of less than 20%, (2) difficulty in obtaining uniform deposition on the substrate, and (3) charge-up damages and ion-bombardment-induced damages resulting from very high electron temperature (>3 eV) and that the substrate is set at the plasma excitation region. In ROT-MS, a number of moving high-density plasma loops are excited on the target surface by rotating helical magnets, resulting in very high target utilization with uniform target erosion and uniform deposition on the substrate. This excellent performance can be principally maintained even if equipment size increases for very large-substrate deposition. Because strong horizontal magnetic fields (>0.05 T) are produced within a very limited region just at the target surface, very low electron-temperature plasmas (<2.5 eV for Ar plasma and <1 eV for direct-current-excited Xe plasma) are excited at the very limited region adjacent to the target surface with a combination of grounded plate closely mounted on the strong magnetic field region. Consequently, the authors can establish charge-up damage-free and ion-bombardment-induced damage-free processes. ROT-MS has been applied for thin-film formation of LaB{sub 6}, which is well known as a stable, low-work-function bulk-crystal material for electron emissions. The work function of the LaB{sub 6} film decreased to 2.8 eV due to enhanced (100)-orientation crystallinity and reduced resistivity realized by adjusting the flux of low-energy bombarding ions impinging on the depositing surface, which work very efficiently, improving the performance of the electron emission devices.

36 MATERIALS SCIENCE↗

Effects of Contact-Induced Doping on the Behaviors of Organic Photovoltaic Devices

Substrates can significantly affect the electronic properties of organic semiconductors. In this paper, we report the effects of contact-induced doping, arising from charge transfer between a high work function hole extraction layer (HEL) and the organic active layer, on organic photovoltaic device performance. Employing a high work function HEL is found to increase doping in the active layer and decrease photocurrent. Combined experimental and modeling investigations reveal that higher doping increases polaron–exciton quenching and carrier recombination within the field-free region. Consequently, there exists an optimal HEL work function that enables a large built-in field while keeping the active layer doping low. This value is found to be ~0.4 eV larger than the pinning level of the active layer material. As a result, these understandings establish a criterion for optimal design of the HEL when adapting a new active layer system and can shed light on optimizing performance in other organic electronic devices.

14 SOLAR ENERGY↗

Development of chemically vapor deposited rhenium emitters of (0001) preferred crystal orientation

Rhenium thermionic emitters were prepared by the pyrolysis of rhenium chlorides formed by the chlorination of rhenium pellets. The impurity contents, microstructures, degrees of (0001) preferred crystal orientation, and vacuum electron work functions of these emitters were determined as a function of deposition parameters, such as substrate temperature, rhenium pellet temperature and chlorine flow rate. A correlation between vacuum electron work function and degree of (0001) preferred crystal orientation was established. Conditions for depositing porosity-free rhenium emitters of high vacuum electron work functions were defined. Finally, three cylindrical rhenium emitters were prepared under the optimum deposition conditions.

Yang, L.↗

Elucidating the Influence of Residual Polymer and Gas Environment on the Electronic Structure of a Graphene Layer Using in Situ APXPS

We use in situ ambient pressure X-ray photoelectron spectroscopy (APXPS) and ultraviolet photoelectron spectroscopy (UPS) to develop an effective method for studying changes in the graphene (Gr) electronic structure according to certain circumstance. The amount of polymethyl methacrylate (PMMA) residual polymer (RP), inevitably generated during the Gr transfer process, is significantly reduced from Gr surface by thermal annealing. This processed Gr is then sequentially exposed to specific gas environments (Ar, N 2 , O 2 , and CO 2 ), and APXPS or UPS is carried out to investigate the variations in the Gr electronic structure including the work function. When the amount of PMMA RP on Gr is reduced, the position of the main carbon peak shifts by more than 0.4 eV to a higher binding energy (in XPS spectra), and the secondary electron cutoff moves by about 0.2 eV to a lower binding energy (in UPS spectra). These changes are generally caused by a decrease in the Gr work function. On the other hand, exposure to the gas environments at different temperatures that we investigated did not produce significant changes in the work function and chemical states of Gr. These results confirm that the material in contact with Gr should be considered to achieve the desired Gr performance in electronics.

36 MATERIALS SCIENCE↗

Transmission Electron Microscopy and Electron Energy-Loss Spectroscopy Studies of Hole-Selective Molybdenum Oxide Contacts in Silicon Solar Cells

In this study, substochiometric hole-selective molybdenum oxide (MoO x ) contacts in crystalline silicon (c-Si) solar cells were investigated by a combination of transmission electron microscopy (TEM) and spatially resolved electron energy-loss spectroscopy (SR-EELS). It was observed that a ≈ 4 nm SiO x interlayer grows at the MoO x /c-Si interface during the evaporation of MoO x over a c-Si substrate. SR-EELS analyses revealed the presence of a 1.5 nm diffused MoO x /indium tin oxide (ITO) interface in both as-deposited and annealed samples. Moreover, the presence of a 1 nm thin layer with a lower oxidation state of Mo was detected at the SiO x /MoO x interface in an as-deposited state, which disappears upon annealing. Altogether, it was evident that no hole-blocking interlayer is formed at the MoO x /ITO interface during annealing and homogenization of the MoO x layer takes place during the annealing process. Furthermore, device simulations revealed that efficient hole collection is dependent on MoO x work function and that reduction in the work function of MoO x results in loss of band bending and negatively impacts hole selectivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Studies of thermionic materials for space power applications

The effect of microstructures of tungsten cladding on the transport rates of carbide fuel components was studied at 2073 K. hyperstoichiometric 90UC-10ZrC containing 4 wt% tungsten was clad with six types of tungsten material of 40 mil thickness. Screening tests of 1000 hours were carried out, and then selected samples were subjected to long-term tests up to 10,000 hours. The results indicate that the microstructures strongly affect the transport rates of carbide fuel components. The conditions for preparing (110) oriented cylindrical chloride tungsten emitters of high vacuum work functions were also investigated. Specimen sets were deposited on fluoride tungsten substrates for evaluating the effects of various deposition parameters on the degree and uniformity of the (110) preferred orientation and the vacuum work function. Long-term tests showed that the high vacuum work function of a cylindrical emitter was stable and the chloride tungsten to fluoride tungsten bond remained in excellent shape after 4850 hours at 2073 K.

Source record↗

Tuning of electronic properties of fullerene-oligothiophene layers

Electronic properties of fullerene derivatives containing oligothiophene pendant chain (1–3 thiophene moieties) were investigated using the Kelvin probe technique and quantum chemistry methods. For electrochemical examination of these systems, Langmuir–Blodgett (LB) layers were prepared by the deposition on a gold substrate. The analysis of the experimental data shows that the value of the work function depends strongly on the length of oligothiophene chain. Similar dependence was also found for the surface photovoltage measurements conducted for the layers consisting of multiple LB films of the examined compounds deposited on gold surfaces. The assumption has been made that these changes are associated with the influence of oligothiophene chain on the electrostatic potential distribution near the surface of the sample. The hypothesis was confirmed by the results of DFT calculations, which revealed that the value of Fermi level energy shifts in the opposite direction to the determined work function. The key highlights of this study are as follows: electronic structure tuning by oligothiophene side chain; DFT calculation on fullerene-thiophene system; work function measurements of thin molecular layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Kelvin probe force microscopy for high-resolution imaging of hydrogen in steel alloys [Poster]

Kelvin probe force microscopy (KPFM) was used to image and co-locate the presence of hydrogen in stainless steel (SS) with microstructure. Various SS samples were investigated, including forged, welded, LENS® fabricated, and pinch welded materials. KPFM images the local work function of a surface as a function of spatial position using atomic force microscopy. KPFM is capable of delivering high spatial (~10 nm) and potential (~5mV) resolution maps characterizing the microstrucure and the locally varying work function of surfaces. Hydrogen segregated at the surface of SS increases the local work function by either reducing tensile strain or by reducing the chemical potential of surface species. In a process known as hydrogen embrittlement, hydrogen segregates to and becomes trapped at extended defects (e.g. dislocations, boundaries, pores) which leads to the initiation of cracking and can result in structural failure. Hydrogen storage necessitates a proper understanding of the mechanisms of hydrogen embrittlement in SS. Developing advanced characterization techniques for hydrogen embrittlement is critical to identify long term solutions for materials exposed to hydrogen. Current techniques of observing hydrogen embrittlement involve mechanical testing, and optical microscopy with low resolution. Advance microstructural imaging techniques capable of resolving features down to the nanometer scale are needed. KPFM provides high resolution imaging for the characterization and development of SS components for hydrogen storage.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modeling the flux of high energy negative ions during reactive magnetron sputtering

The negative ion flux during reactive sputtering from planar and rotating cylindrical magnetrons has been studied. Energy resolved mass spectrometry was used to measure the energy and mass distribution of the negative ions. Also the angular distribution of the high energy ions was characterized for planar as well as for rotating cylindrical magnetrons. Besides these measurements, a binary collision Monte Carlo simulation code, SiMTRA, was adapted in order to simulate the energy, mass, and angular distribution of the high energy negative ions. All simulated distributions, for both planar and rotating cylindrical magnetrons, were in excellent correspondence with the experimental observations. Also a model for the amount of high energy negative O{sup -} ions was proposed. Indeed, the logarithm of the amount of high energy negative O{sup -} ions is shown to be related to the secondary electron emission yield of the oxide target, and these two parameters are known to be related to the work function. The SiMTRA simulations, in combination with knowledge of the work function or secondary electron emission yield of the target, allow modeling the flux of high energy negative ions during reactive magnetron sputtering.

36 MATERIALS SCIENCE↗

Adsorption Structures and Electronic Properties of 1,4-Phenylene Diisocyanide on the Au(111) Surface

The adsorption structures and electronic properties of 1,4-phenylene diisocyanide (PDI) on a Au(111) surface have been studied using temperature programmed desorption (TPD), two-photon photoemission (2PPE), and scanning tunneling microscopy (STM). As deposited at 95 K, PDI molecules form disordered islands and short one-dimensional chains on Au(111) terraces. The work function decreases with increasing PDI coverage, and an occupied electronic state appears at 0.88 eV below the Fermi level. Annealing to 300 K causes the PDI molecules to reorganize on the surface and form ordered, one-dimensional molecular chains that extend for many tens of nanometers across the Au(111) terraces. The repeating structure of the molecular chains is consistent with a recently proposed [-Au-PDI-]{sub n} structure in which PDI molecules lie parallel to the surface and are interconnected by Au adatoms released from the Au(111) surface. The formation of the molecular chains is accompanied by a large drop in the work function which we attribute to an increase in the number and magnitude of interfacial dipoles. The electronic structure of the molecular chains is also characterized by occupied and unoccupied states at -0.88 eV below and +3.32 eV above the Fermi level, respectively. The latter are most prominent after annealing a PDI/Au(111) surface to 300 K, indicating that they are associated with interfacial states of the one-dimensional molecular chains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Back-gated graphene anode for more efficient thermionic energy converters

Thermionic energy converters (TECs) are a direct heat-to-electricity conversion technology with great potential for high efficiency and scalability. However, space charge barrier in the inter-electrode gap and high anode work function are major obstacles toward realizing high efficiency. Here, we demonstrate for the first time a prototype TEC using a back-gated graphene anode, a barium dispenser cathode, and a controllable inter-electrode gap as small as 17 µm, which simultaneously addresses these two obstacles. This leads to an electronic conversion efficiency of 9.8% at cathode temperature of 1000 °C, the highest reported by far. We first demonstrate that electrostatic gating of graphene by a 20 nm HfO 2 dielectric layer changes the graphene anode work function by 0.63 eV, as observed from the current-voltage characteristics of the TEC. Next, we show that the efficiency increases by a factor of 30.6 by reducing the gap from 1 mm down to 17 µm, after a mono-layer of Ba is deposited on graphene by the dispenser cathode. Lastlu, we show that electrostatic gating of graphene further reduces the graphene work function from 1.85 to 1.69 eV, leading to an additional 67% enhancement in TEC efficiency. Note that the overall efficiency using the back-gated graphene anode is 6.7 times higher compared with that of a TEC with a tungsten anode and the same inter-electrode gap.

30 DIRECT ENERGY CONVERSION↗

Comment on “Tunneling-tip-induced collapse of the charge gap in the excitonic insulator Ta 2 NiSe 5 ”

In this study, we investigate the discrepancy between the estimate of Q. He [], who observed a remarkable collapse of the exciton gap in Ta 2 NiSe 5 due to the electrostatic field between the scanning tunneling microscope (STM) tip and the sample, and that of a recent angle-resolved photoemission spectroscopy investigation [C. Chen , ]. It is proposed that a critical factor contributing to this discrepancy is due to He 's assumption of a constant work function of the STM tip. This assumption led to an underestimation of the tip-induced electric field. Using a literature value for the sample work function, a more substantial electric field strength is obtained, which resolves the apparent conflict between the doping estimates of these two techniques. Furthermore, our findings highlight the importance of the STM tip condition, which can significantly impact the tip work function and, consequently, influence the doping estimation in experiments involving tip-induced electric fields. Published by the American Physical Society 2024

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗