Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transitional flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Effects of mass addition on blunt-body boundary-layer transition and heat transfer

The model bodies tested at Mach number 7.32 were hemispheres, blunt cones, and spherical segments. The mass addition consisted of air ejected through porous forward surfaces of the models. The experimental data consisted of heat transfer measurements from which boundary layer transitions were deduced. The data verified various applicable boundary layer codes in the laminar and transitional flow regimes. Empirical heating rate data correlations were developed for the laminar and turbulent flow regimes.

Kaattari, G. E.↗

Method for calculating convective heat-transfer coefficients over turbine vane surfaces

A method for calculating laminar, transitional, and turbulent convective heat-transfer coefficients for turbine vane surfaces is described. An approximate integral solution method produced results in good agreement with a finite-difference solution. Comparisons between the two are presented. The integral solution results agreed well with the finite-difference solution results in the laminar and turbulent regions. Differences in calculating the start of transition produced a later starting point for the approximate integral solution's transitional flow regime.

Gauntner, D. J.↗

Correlation of turbulent shear layer attachment peak heating near Mach 6

A correlation of new turbulent two-dimensional data and peak heating data for attaching free shear layers is presented for a 2.54-cm and 5.08-cm diam cylindrical leading-edge slab 25.4 cm long, and 7.62 and 10.16 cm wide. A 30.48 x 25.4 cm sharp leading-edge flat plate set at 15 and 20 deg is used to generate plane impinging shocks. The freestream Mach number is 6 and the freestream Reynolds number varies from 3,300,000 to 25,600,000/m. Peak heating is measured on silica-based epoxy models with a phase change coating technique. A comparison of the free shear layer data with the transition data of Birch and Keyes (1972) reveals that the shear layer data are turbulent at attachment. The trend of the data shows that peak heating is strongly affected by the state of development at attachment. As the free shear layers become more fully developed, the data approach the two-dimensional correlation. Persistence of transitional flow structures for supersonic free shear flows is pointed out.

Keyes, J. W.↗

Comparison of quick-look plume heating calculations and Monte Carlo direct simulation

A quick-look method has been developed for estimating convective heat flux due to plume impingement in the transition flow regime on a concave surface surrounding a rocket nozzle. Comparison with the flowfield and heat fluxes computed by the Monte Carlo Direct Simulation Method show the quick-look method to be conservative. Assumptions regarding the nature of the flowfield based on engineering judgment were shown to be essentially valid. Further, the assumption of free molecular impingement was shown to be non-conservative for portions of the surface. Potential refinements of the quick-look method are discussed.

Guernsey, C. S.↗

Energy efficient engine, low-pressure turbine boundary layer program

A study was conducted to investigate development of boundary layers under the influence of velocity distributions simulating the suction side of two state-of-the-art turbine airfoils: a forward loaded airfoil (squared-off design) and an aft loaded airfoil (aft-loaded design). These velocity distributions were simulated in a boundary layer wind tunnel. Detailed measurements of boundary layer mean velocity and turbulence intensity profiles were obtained for an inlet turbulence level of 2.4 percent and an exit Reynolds number of 800,000. Flush-mounted hot film probes identified the boundary layer transition regimes in the adverse pressure gradient regions for both velocity distributions. Wall intermittency data showed good agreement with the correlations of Dhawan and Narasimha for the intermittency factor distribution in transitional flow regimes.

Gardner, W. B.↗

Aerodynamic heating on the corrugated surface of a 10.2 deg half-angle blunted cone at Mach 6.7

A 10.2 deg half-angle blunted cone with corrugated surfaces was tested in the Langley 8-foot high-temperature structures tunnel to measure the aerodynamic heating of its surfaces. The tests were made in a turbulent boundary layer at angles of attack of 0 deg, 5 deg, and 10 deg. Heating of the windward side was in reasonable agreement with theoretical turbulent predictions for a smooth cone, while heating on the leeward side was between laminar and turbulent predictions as a result of local transitional flow or flow separation produced by high lee-side pressures. Localized heating measurements indicated a significant increase in heating at large cross-flow angles, with the maximum heating rates occurring where the flow reattaches on the upstream side of the corrugation crest and the minimum occurring on the downstream side where the flow is separated.

Weinstein, I.↗

The Shuttle Orbiter high resolution accelerometer package experiment - Preliminary flight results

A description of the High Resolution Accelerometer Package (HiRAP) experiment, designed to measure rarefied flow aerodynamic accelerations, is given. The ground test calibration factors, as well as post-flight data processing techniques to extract aerodynamic accelerations, are discussed and applied to the recorded reentry data of the recent STS-6 Shuttle Orbiter flight. The ratio of the measured normal-to-axial aerodynamic accelerations during reentry is used to obtain the first flight measurement of the lift-to-drag ratio (L/D) of a winged entry vehicle in the rarefied flow flight regime. The preliminary result for the free-molecule flow L/D is 0.10 + or - 0.03. The initial flight results on L/D are compared with current predictions which are based upon theoretical and empirical considerations. The measured free-molecule flow L/D value is higher than predicted by a factor of about three, indicating that surface reflection is not completely diffuse as currently assumed. In the rarefied flow transition regime, the Shuttle data book-bridging formula fits the flight data adequately. Upper altitude density profiles are also deduced from the measurements and presented. The density profiles show a wave phenomena with amplitude of about 60 percent, relative to a standard model.

Blanchard, R. C.↗

Shuttle Continuous Open Wind Tunnel (SCOWT)

The aerodynamic and heat transfer coefficients are studied within the range of thermo-fluid-dynamic conditions experienced by a satellite during Tethered Satellite System (TSS) atmospheric flights. The gasdynamic processes occuring downstream of the bow wave standing in front of the satellite are also studied. The knowledge of the chemistry and physics of the upper atmosphere related to satellite aerothermodynamics is furthered. The existence of an overshooting of the air drag coefficient of the sphere in the transition regime is validated. A complete set of measurements is performed in order to provide the data base to develop and validate theoretical models of free molecule transition flow fields.

Carlomagno, G. M.↗

Flow regimes in a shallow rotating cylindrical annulus with temperature gradients imposed on the horizontal boundaries

Experimental flow regime diagrams are determined for a new rotating cylindrical annulus configuration which permits a measure of control over the internal vertical temperature gradient. The new annulus has radial temperature gradients imposed on plane horizontal thermally conducting endwalls (with the cylindrical sidewalls as insulators) and is considered to be more relevant to atmospheric dynamics studies than the classical cylindrical annulus. Observations have revealed that, in addition to the axisymmetric flow and nonaxisymmetric baroclinic wave flow which occur in the classical annulus, two additional nonaxisymmetric flow types occur in the new annulus: boundary-layer thermal convection and deep thermal convection. Flow regime diagrams for three different values of the imposed vertical temperature difference are presented, and explanations for the flow transitions are offered. The new annulus provides scientific backup for the proposed Atmospheric General Circulation Experiment for Spacelab. The apparatus diagram is included.

Hathaway, D. H.↗

Advances and future directions of research on spectral methods

Recent advances in spectral methods are briefly reviewed and characterized with respect to their convergence and computational complexity. Classical finite element and spectral approaches are then compared, and spectral element (or p-type finite element) approximations are introduced. The method is applied to the full Navier-Stokes equations, and examples are given of the application of the technique to several transitional flows. Future directions of research in the field are outlined.

Patera, A. T.↗

An aerothermodynamic study of slender conical vehicles

A numerical study was performed to assess the applicability of some current techniques which can be used for aerothermal predictions over slender spherically blunted cones. Predictions using a viscous-shock-layer method and several engineering approaches were compared with experimental results from flight and ground-based tests, with each other, and with other detailed results. Good agreement was obtained in comparisons with laminar and turbulent heating data from the Reentry F flight vehicle and with the wind-tunnel data. In particular, the viscous-shock-layer method was shown to yield excellent comparisons and should be useful in providing detailed flowfield and surface values for slender blunted cones. Additional predictions were obtained with these methods for two 5-deg half-angle cones with different nose radii to illustrate the effects of nose bluntness and angle of attack on drag and heat transfer. These results demonstrate the benefit of nose blunting with respect to heating and drag for laminar and transitional flow at zero-lift conditions and the benefit of heating reduction at angle of attack. Detailed comparison of the engineering code predictions with the viscous-shock-layer results for these additional cases generally showed good agreement except for the laminar prodictions at angle of attack on the forward cone surface. Nonequilibrium calculations at 0-deg angle of attack showed that substantial benefits of low surface catalysis existed only in the nose-dominated region.

Thompson, R. A.↗

Petrov-Galerkin methods for natural convection in directional solidification of binary alloys

A Petrov-Galerkin finite element method is presented for calculation of the steady, axisymmetric thermosolutal convection and interface morphology in a model for vertical Bridgman crystal growth of nondilute binary alloys. The Petrov-Galerkin method is based on the formulation for biquadratic elements developed by Heinrich and Zienkiewicz and is introduced into the calculation of the velocity, temperature and concentration fields. The algebraic system is solved simultaneously for the field variables and interface shape by Newton's method. The results of the Petrov-Galerkin method are compared critically with those of Galerkin's method using the same finite element grids. Significant improvements in accuracy are found with the Petrov-Galerkin method only when the mesh is refined and when the formulation of the residual equations is modified to account for the mixed boundary conditions that arise at the solidification interface. Calculations for alloys with stable and unstable solute gradients show the occurrence of classical flow transitions and morphological instabilities in the solidification system.

Adornato, Peter M.↗

Analysis of a second-order-accurate finite-volume method for temporally-growing compressible shear layers

A finite-volume method for solving the compressible laminar Navier-Stokes equation in two dimensions is assessed for use in the simulation of transitional flows. The method is second-order-accurate, uses alternating-direction-implicit time integration, and a total-variation-diminishing smoothing operator in the inviscid flux terms. The test problem was a free shear layer with a forced periodicity in x at a specified wavelength and with the parallel mean flow specified as a hyperbolic-tangent profile. A grid refinement investigation verified this method to be second-order-accurate with less than 4 percent error in the growth rate of isolated modes on a 32 by 64 grid. The interaction between modes of similar amplitude was small, less than 1 percent. However, in cases where there was a dominant mode, numerical phase error pumped energy into all other modes. This error results in nonphysical growth rate for modes whose energy content is several orders of magnitude below the dominant mode. In the case when the dominant mode saturates, the pumping action stops and the growth rate of the next largest growing mode regains physical significance.

Atkins, H. L.↗

Aeroassist flight experiment aerodynamics and aerothermodynamics

The problem is to determine the transitional flow aerodynamics and aerothermodynamics, including the base flow characteristics, of the Aeroassist Flight Experiment (AFE). The justification for the computational fluid dynamic (CFD) Application stems from MSFC's system integration responsibility for the AFE. To insure that the AFE objectives are met, MSFC must understand the limitations and uncertainties of the design data. Perhaps the only method capable of handling the complex physics of the rarefied high energy AFE trajectory is Bird's Direct Simulation Monte Carlo (DSMC) technique. The 3-D code used in this analysis is applicable only to the AFE geometry. It uses the Variable Hard Sphere (VHS) collision model and five specie chemistry model available from Langley Research Center. The code is benchmarked against the AFE flight data and used as an Aeroassisted Space Transfer Vehicle (ASTV) design tool. The code is being used to understand the AFE flow field and verify or modify existing design data. Continued application to lower altitudes is testing the capability of the Numerical Aerodynamic Simulation Facility (NASF) to handle 3-D DSMC and its practicality as an ASTV/AFE design tool.

Brewer, Edwin B.↗

Use of finite volume schemes for transition simulation

The use of finite-volume methods in the study of spatially and temporally evolving transitional flows over a flat plate is investigated. Schemes are developed with both central and upwind differencing. The compressible Navier-Stokes equations are solved with a Runge-Kutta time stepping scheme. Disturbances are determined using linear theory and superimposed at the inflow boundary. Time accurate integration is then used to allow temporal and spatial disturbance evolution. Characteristic-based boundary conditions are employed. The requirements of using finite-volume algorithms are studied in detail. Special emphasis is placed on difference schemes, grid resolution, and disturbance amplitudes. Moreover, comparisons are made with linear theory for small amplitude disturbances. Both subsonic and supersonic flows are considered, and it is shown that the locations of branch 1 and branch 2 of the neutral stability curve are well predicted, given sufficient resolution.

Fenno, Charles C., Jr.↗

Static pressure measurements in A 30 kWe class arcjet

A series of cold and hot flow static pressure measurements have been made as a function of distance along the principal axis of a 30 kWe arcjet. During these experiments, the background pressure was varied from atmospheric pressure to less than 1 Torr. The experimental arcjet used in these tests had the same constrictor and conical nozzle dimensions as the baseline MOD-1 ammonia arcjet developed at NASA-JPL, but used nitrogen as the propellant gas. Comparison of the measured static pressure profiles with the arc erosion patterns on the anode surface showed that anode arc attachment points directly coincided with the minimum static pressure points. The dual voltage modes commonly observed in 30 kWe class arcjet thrusters are also believed to be caused by the presence of two pressure minima in the arcjet, one at the constrictor entrance and the other in the expansion nozzle. The static pressure profiles also suggest that the sonic flow transition occurs at the entrance to the nozzle, indicating the existence of very thick boundary layers in the arcjet constrictor.

Harris, William J.↗

Plasma motion in the Venus ionosphere - Transition to supersonic flow

A remarkable feature of the ionosphere of Venus is the presence of nightward supersonic flows at high altitude near the terminator. In this paper it is shown that the relatively high pressure dayside plasma wells up slowly, and at high altitude it is accelerated horizontally through a relatively constricted region near the terminator toward the low-density nightside. In effect, the plasma flows through a 'nozzle' that is first converging, then diverging, permitting the transition to supersonic flow. The model plasma accelerates to supersonic speeds, reaching sonic speed just behind the terminator. The ion transport rates are sufficient to produce and maintain the nightside ionosphere.

Whitten, R. C.↗

STS-40 orbital acceleration research experiment flight results during a typical sleep period

The Orbital Acceleration Research Experiment (OARE), an electrostatic accelerometer package with complete on-orbit calibration capabilities, was flown for the first time aboard the Space Shuttle on STS-40. This is also the first time an accelerometer package with nano-g sensitivity and a calibration facility has flown aboard the Space Shuttle. The instrument is designed to measure and record the Space Shuttle aerodynamic acceleration environment from the free molecule flow regime through the rarified flow transition into the hypersonic continuum regime. Because of its sensitivity, the OARE instrument defects aerodynamic behavior of the Space Shuttle while in low-earth orbit. A 2-hour orbital time period on day seven of the mission, when the crew was asleep and other spacecraft activities were at a minimum, was examined. During the flight, a 'trimmed-mean' filter was used to produce high quality, low frequency data which was successfully stored aboard the Space Shuttle in the OARE data storage system. Initial review of the data indicated that, although the expected precision was achieved, some equipment problems occurred resulting in uncertain accuracy. An acceleration model which includes aerodynamic, gravity-gradient, and rotational effects was constructed and compared with flight data. Examination of the model with the flight data shows the instrument to be sensitive to all major expected low frequency acceleration phenomena; however, some erratic instrument bias behavior persists in two axes. In these axes, the OARE data can be made to match a comprehensive atmospheric-aerodynamic model by making bias adjustments and slight linear corrections for drift. The other axis does not exhibit these difficulties and gives good agreement with the acceleration model.

Blanchard, R. C.↗