Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRANSITION TEMPERATURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Study of deposition of YBa2Cu3O7-x on cubic zirconia

Films of YBa2Cu3O7-x were grown on (100) cubic zirconia with 8 percent yttria by laser ablation from sintered targets of YBa2Cu3O7-x. The temperature of the zirconia substrate during growth was varied between 700 and 780 C. The atmosphere during growth was 170 mtorr of O2. The films were subsequently slowly cooled in-situ in 1 atm of O2. The best films were c-axis aligned and had a transition temperature of 87.7 K. The superconducting transition temperature and the X-ray diffraction analysis is reported as a function of the substrate temperature and of the angle between the laser beam and the target's normal.

Warner, Joseph D.↗
NASA NTRS1985

Deconfining phase transition and the continuum limit of lattice quantum chromodynamics

A large-scale Monte Carlo calculation is presented of the deconfining phase-transition temperature in lattice quantum chromodynamics without fermions. By using the Wilson action, it is found that the transition temperature as a function of the lattice coupling g is consistent with scaling behavior dictated by the perturbative beta function for 6/g-squared greater than 6.15.

Gottlieb, S. A.↗
DOE OSTI2025

Superconducting dome and structural changes in LaRu 3 ⁢Si 2 under pressure

LaRu 3 ⁢Si 2 is of current research interest as a kagome metal with a superconducting transition temperature, 𝑇 𝑐 ∼7 K, and higher-temperature charge density wave orders. Here we report on electrical transport and x-ray diffraction measurements on LaRu 3 ⁢Si 2 under pressure up to 65 GPa and 35 GPa, respectively. The superconducting transition temperature 𝑇 𝑐 first gets slightly enhanced and reaches a maximum ∼8.7 K at ∼8.5 GPa. With further applied pressure, 𝑇 𝑐 is initially gradually suppressed, then more rapidly suppressed, followed by gradual suppression, revealing a superconducting dome. Two possible pressure-induced structural phase transitions are also observed at room temperature, from the original hexagonal phase to another hexagonal structure above ∼11.5 GPa, and further to a structure with lower symmetry above ∼23.5 GPa. These transition pressures roughly correlate with features found in our pressure-dependent transport data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1972

Mechanical properties of electron-beam-melted molybdenum and dilute molybdenum-rhenium alloys

A study of molybdenum and three dilute molybdenum-rhenium alloys was undertaken to determine the effects of rhenium on the low temperature ductility and other mechanical properties of molybdenum. Alloys containing 3.9, 5.9, and 7.7 atomic percent rhenium exhibited lower ductile-brittle transition temperatures than did the unalloyed molybdenum. The maximum improvement in the annealed condition was observed for molybdenum - 7.7 rhenium, which had a ductile-brittle transition temperature approximately 200 C (360 F) lower than that for unalloyed molybdenum. Rhenium additions also increased the low and high temperature tensile strengths and the high temperature creep strength of molybdenum. The mechanical behavior of dilute molybdenum-rhenium alloys is similar to that observed for dilute tungsten-rhenium alloys.

Klopp, W. D.↗
NASA NTRS1992

The effect of strain rate and temperature on the tensile properties of NiAl

Tensile testing of cast and extruded binary NiAl was performed from 300 to 900 K at strain rates of 0.00014 to 0.14/s. The brittle-to-ductile transition temperature (BDTT) was dependent on strain rate, with a three-order-of-magnitude increase in strain rate resulting in approximately a 200-K increase in transition temperature. Regardless of strain rate, at temperatures just above the BDTT the fracture strength increased significantly and the fracture morphology changed from mostly intergranular to predominantly transgranular. It was also determined that the mechanism responsible for the brittle-to-ductile transition in NiAl had an apparent activation energy of approximately 118 kJ/mol. These results support the argument that the mechanism for the brittle-to-ductile transition in NiAl is associated with the onset of thermally activated deformation process. This process is probably dislocation climb controlled by short circuit diffusion.

Noebe, R. D.↗
DOE OSTI2023

Segmental relaxation of sequence defined polymers

For this work, the dynamical behavior of sequence defined polymers, P(C n EG 4 ), was studied using dielectric spectroscopy showing one segmental relaxation in addition to a secondary relaxation. In case of segmental relaxation, the relaxation times strongly depend on the molecular weight at low temperatures, while at higher temperatures, unlike to linear homo polymers, this effect levels out. With increasing length of C-units, the segmental relaxation accelerates. This is also reflected in the glass transition temperature, extracted from dielectric spectroscopy. With increasing length of C-units the glass transition temperature decreases, compatible with the accelerated segmental relaxation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Role of Intra-Domain Heterogeneity on Ion and Polymer Dynamics in Block Polymer Electrolytes: An Approach for Spatially Resolving Dynamics and Ion Transport

The design of safe and high-performance, nanostructured, block polymer (BP) electrolytes for lithium-ion batteries requires a thorough understanding of the key parameters that govern local structure and dynamics. Yet, the interfaces between microphase separated domains can introduce complexities in this local behavior that can be challenging to quantify. Herein, the local polymer, cation (Li + ), and anion dynamics were described in salt-doped polystyrene block poly(oligo-oxyethylene methyl ether methacrylate) (PS-b-POEM) through a quantitative framework that considered the effects of polymer architecture, segmental mixing, chain stretching, and confinement on polymer mobility and ion transport. This framework was validated through nuclear magnetic resonance (NMR) spectroscopy measurements on solid (dry) polymer electrolyte samples. Notably, a mobility transition temperature (T mobility ) was identified through NMR spectroscopy that captured the local dynamics more accurately than the thermal glass transition temperature. Additionally, the approach quantitatively described the mobility gradient across a domain when segmental mixing effects were combined with chain stretching and confinement information, especially at higher segregation strengths – facilitating the assessment of local ion diffusion and conductivity. As a result, spatially averaged local ion diffusion predictions quantitatively matched NMR-measured ion diffusivities in the BP samples, while spatially summed ionic conductivity predictions across a domain qualitatively captured trends in the measured ionic conductivities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1992

Development of high T(sub c) (greater than 110 K) Bi, Tl, and Y-based materials as superconducting circuit elements

Experimental work has continued on the development and characterization of bulk and hot pressed powders and tapecast materials in the Bi-Sr-Ca-Cu-O and Tl-Ba-Ca-Cu-O systems. A process for producing warp-free, sintered, superconducting tapes of Bi composition Bi2Sr2Ca2Cu3O(x) with a mixed oxide process was established. This procedure required a triple calcination at 830 C for 24 hours and sintering at 845 C from 20 to 200 hours. Hot pressing the triple calcined powder at 845 C for 6 hours at 5000 psi yielded a dense material which on further heat treatment at 845 C for 24 hours exhibited a Tc of 108.2 K. A further improvement in the processing of the bismuth materials was achieved via a chemical coprecipitation process wherein the starting nitrate materials were coprecipitated with oxalic acid, thus yielding a more chemically homogeneous, more reactive powder. With the coprecipitated powders, only one calcine at 830 C for 12 hours and a final sinter at 845 C for 30 hours was sufficient to produce a bulk superconducting material with a Tc of 108.4 K. SAFIRE-type grounding links were successfully fabricated from sintered, tapecast, coprecipitated BSCCO 2223 powders. Compositional and processing investigations were continued on the Tl-based superconductors. Manganese and lithium additions and sintering temperature and time were examined to determine their influence on superconducting properties. It was found that lithium substitutions for copper enhance the transition temperatures while manganese additions produced deleterious effects on the superconducting properties. A suitable procedure for producing reproducible bulk and tapecast material of Tl composition Tl2Ba2Ca2Cu3O(x) was developed and used in fabricating uniform superconducting tapes. The highest transition temperature for Tl-based tapes was measured at 110.2 K. Thallium superconducting SAFIRE-type grounding links were fabricated from the tapes.

Haertling, Gene H.↗
DOE OSTI2021

Charpy impact tests of tungsten fiber–reinforced composite from -150 °C to 1000 °C

Tungsten features a unique combination of properties that makes it a favorable plasma-facing material in fusion reactors. The main drawbacks of tungsten are its brittleness at room temperature and the potential embrittlement during operation. Tungsten fiber–reinforced composites have the potential to overcome these limitations. Charpy impact tests ranging from -150 °C to 1000 °C have been performed. To identify the ductile-to-brittle transition temperature and understand the behavior at high temperature a detailed microscopic investigation was used to identify the transition temperature of fiber and matrix, which was between -100 °C to -50 °C and 1000 °C, respectively.

36 MATERIALS SCIENCE↗
NASA NTRS1972

A proposed magnetic digital temperature transducer, volume 1

A study has been made of the feasibility of using the discontinuous permeability versus temperature characteristics of some magnetic materials for a digital temperature transducer and a thermally controlled ON-OFF switch. Simple logic converts the number of output pulse to a digital word recognizable by the system. Efforts have been concentrated on materials with Curie temperatures between 0 and 100 C. One compound has the composition Mn(5-x)Fe(x)Ge3 where the amount of iron determines the transition temperature. The other compound is Ni-Zn ferrite and has the compositon Ni(1-x)Zn(x)Fe(1.95)O4 where the nickel: zinc ratio determines the transition temperature. A detailed report of materials prepared is presented. Toroidal inductors of the material have been constructed and the change in inductance with temperature measured. In view of these initial measurements, it is felt that a transducer utilizing the permeability versus temperature characteristics of these materials has promise as a reliable and sensitive solid state digital temperature transducer.

Collier, T. E.↗
DOE OSTI2025

Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites

This study investigates the hygrothermal aging behavior and thermomechanical properties of as-manufactured glass fiber-reinforced epoxy and thermoplastic composite tidal turbine blades. The blades were previously deployed in a marine environment and subsequently analyzed through a comprehensive suite of material characterization techniques, including hygrothermal aging, dynamic mechanical analysis (DMA), tensile testing and X-ray computed tomography (XCT). Hygrothermal aging experiments revealed that while thermoplastic composites exhibited lower overall water absorption (0.78% vs. 0.47%), they had significantly higher diffusion coefficients than epoxy (2.1 vs. 12.1 × 10 −13 m 2 s −1 ), suggesting faster saturation in operational environments. DMA results demonstrated that water ingress caused plasticization in epoxy matrices, reducing the glass transition temperature and increasing damping (112 °C to 104 °C), while thermoplastic composites showed more stable thermal behavior (87 °C glass transition temperature). Tensile testing revealed substantial reductions in ultimate strength (>40%) for both materials after prolonged water exposure, with minimal change in elastic modulus, highlighting the role of matrix degradation over fiber reinforcement. XCT image analysis showed that both composites were manufactured with high quality: no large voids or cracks were present, and the degree of misalignment was low. These findings inform future marine renewable energy composite designs by emphasizing the critical influence of moisture on long-term structural integrity and the need for optimized material systems in harsh marine environments. This work provides a rare real-world comparison of epoxy and recyclable thermoplastic tidal turbine blades, showing how laboratory aging tests and advanced imaging reveal the influence of material and manufacturing choices on long-term marine durability.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Variable-Temperature Scattering and Spectroscopy Characterizations for Temperature-Dependent Solution Assembly of PffBT4T-Based Conjugated Polymers

The solution structure of conjugated polymers (CPs) from which the films are cast is critical for tailoring the thin-film morphology thus device performance. Here, we used multimodal variable-temperature scattering and spectroscopy tools to fully quantify the solution assembly of poly[(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3'''-dialkyl-2,2';5',2'';5'',2'''-quaterthiophen-5,5'''-diyl)] (PffBT4T) polymers with varying side-chain lengths at different assembly temperatures. The conformational and aggregation behaviors for PffBT4T-based CPs were found to be very sensitive to both temperature and side chain length using ultraviolet–visible (UV–vis) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, dynamic light scattering (DLS), and small-angle neutron scattering (SANS). We found that with slightly increasing side chain length from 2-octyldodecyl (C8C12) to 2-nonyltridecyl (C9C13), PffBT4T-based CPs show a significant decrease in aggregation-to-dissolved chain transition temperature (10 °C), degree of aggregation, enthalpy change of aggregation, and size of the aggregates in solution. At room temperature, PffBT4T polymer strongly aggregated to form fabric structure with the film thickness of a few nanometers in thickness and hundreds of nanometers in length, as probed by atomic force microscopy (AFM), transmission electronic microscopy (TEM), and dynamic light scattering (DLS). At the elevated temperature above the aggregation-to-dissolved chain transition temperature, PffBT4T is fully dissolved and adopts a semiflexible coil conformation with the persistence length of 3.1 nm for PffBT4T-C8C12 and a slightly increased persistence length of 3.4 nm for PffBT4T-C9C13, according to temperature-dependent SANS measurements. Longer side chains of PffBT4T-C9C13 also lead to less aggregation enthalpy gain compared with PffBT4T-C8C12. This work provides a solution structure manipulating strategy of CPs and thus will inspire the molecular design and processing protocols of CPs toward higher performance electronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Multiaxial Temperature- and Time-Dependent Failure Model

A temperature- and time-dependent mathematical model predicts the conditions for failure of a material subjected to multiaxial stress. The model was initially applied to a filled epoxy below its glass-transition temperature, and is expected to be applicable to other materials, at least below their glass-transition temperatures. The model is justified simply by the fact that it closely approximates the experimentally observed failure behavior of this material: The multiaxiality of the model has been confirmed (see figure) and the model has been shown to be applicable at temperatures from -20 to 115 F (-29 to 46 C) and to predict tensile failures of constant-load and constant-load-rate specimens with failure times ranging from minutes to months..

Richardson, David↗
DOE OSTI2023

Unreliability of two-band model analysis of magnetoresistivities in unveiling temperature-driven Lifshitz transition

Recently, anomalies in the temperature dependences of the carrier density and/or mobility derived from analysis of the magnetoresistivities using the conventional two-band model have been used to unveil intriguing temperature-induced Lifshitz transitions in various materials. For instance, two temperature-driven Lifshitz transitions were inferred to exist in the Dirac nodal-line semimetal ZrSiSe, based on two-band model analysis of the Hall magnetoconductivities where the second band exhibits a change in the carrier type from holes to electrons when the temperature decreases below T=106K and a dip is observed in the mobility vs temperature curve at T=80K. Here, in this study, we revisit the experiments and two-band model analysis on ZrSiSe. We show that the anomalies in the second band may be spurious because the first band dominates the Hall magnetoconductivities at T>80K, making the carrier type and mobility obtained for the second band from the two-band model analysis unreliable. That is, care must be taken in interpreting these anomalies as evidence for temperature-driven Lifshitz transitions. Our skepticism on the existence of such phase transitions in ZrSiSe is further supported by the validation of Kohler's rule for magnetoresistances for T≤180K. In this paper, we showcase potential issues in interpreting anomalies in the temperature dependence of the carrier density and mobility derived from the analysis of magnetoconductivities or magnetoresistivities using the conventional two-band model.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Adhesion of Self-Complementary, Sinusoidal Surfaces Fabricated Using Two-Photon Polymerization

Microscale, pick-and-place assembly is a non-lithographic assembly method poised to impact diverse fields including flexible electronics, microfluidics and robotics. However, a major technological challenge is the need to deterministically control adhesion between parts. Here, switchable adhesion involving 3D-printed, self-complementary surfaces is demonstrated. Mechanical properties of metasurfaces pressed against flat, rigid substrates are modeled using finite element methods. A series of flat slabs and metastructured slabs with 2D sinusoidal surfaces are printed using two-photon polymerization (2PP) of a shape-memory resin. The surface frequency of featured slabs was varied between $3.\bar3$ mm −1 and $26.\bar6$ mm −1 with similar amplitudes. Adhesion between printed metasurfaces and glass and between printed, self-complementary metasurfaces is studied above and below the cured resin’s glass transition temperature (∼45 °C). Simple heating of adhering surfaces to above 60 °C lowers adhesion, and compression of surfaces while above the glass transition temperature followed by cooling to room temperature elevates adhesion. The nominal adhesive strength between printed, self-complementary surfaces, as determined by the maximum observable pull-off stress, exceeds 3 MPa. Further tailoring complementary surfaces for adhesion control may facilitate microscale disassembly for recovery of components or precious metals.

amorphous materials↗
NASA NTRS2014

Properties of Superconducting Mo, Mo2n and Trilayer Mo2n-Mo-Mo2n Thin Films

We present measurements of the properties of thin film superconducting Mo, Mo2N and Mo2N/Mo/Mo2N trilayers of interest for microwave kinetic inductance detector (MKID) applications. Using microwave resonator devices, we investigate the transition temperature, energy gaps, kinetic inductance, and internal quality factors of these materials. We present an Usadel-based interpretation of the trilayer transition temperature as a function of trilayer thicknesses, and a 2-gap interpretation to understand the change in kinetic inductance and internal resonance quality factor (Q) as a function of temperature.

Superconducting↗
DOE OSTI2021

Giant and Reversible Barocaloric Effect in Trinuclear Spin–Crossover Complex Fe 3 (bntrz) 6 (tcnset) 6

A giant barocaloric effect (BCE) in a molecular material Fe 3 (bntrz) 6 (tcnset) 6 (FBT) is reported, where bntrz = 4-(benzyl)-1,2,4-triazole and tcnset = 1,1,3,3-tetracyano-2-thioethylepropenide. The crystal structure of FBT contains a trinuclear transition metal complex that undergoes an abrupt spin-state switching between the state in which all three FeII centers are in the high-spin (S = 2) electronic configuration and the state in which all of them are in the low-spin (S = 0) configuration. Despite the strongly cooperative nature of the spin transition, it proceeds with a negligible hysteresis and a large volumetric change, suggesting that FBT should be a good candidate for producing a large BCE. Powder X-ray diffraction and calorimetry reveal that the material is highly susceptible to applied pressure, as the transition temperature spans the range from 318 at ambient pressure to 383 K at 2.6 kbar. Despite the large shift in the spin-transition temperature, its nonhysteretic character is maintained under applied pressure. Such behavior leads to a remarkably large and reversible BCE, characterized by an isothermal entropy change of 120 J kg –1 K –1 and an adiabatic temperature change of 35 K, which are among the highest reversible values reported for any caloric material thus far.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Evolution of charge density wave soft phonon modes in Pd 𝑥 ⁢ErTe 3

Here, we investigated the lattice dynamics of quasi-two-dimensional Pd-intercalated ErTe 3 in relation to its charge-density-wave (CDW) transitions by means of x-ray diffuse and meV-resolution inelastic x-ray scattering. In pristine ErTe 3 , CDW order develops at orthogonal in-plane wave vectors q$^𝑐_1$ =(0,0,0.29) (the 𝑐−CDW ) and q$^𝑎_2 $= (0.31,0,0) (the 𝑎−CDW ), with transition temperatures $𝑇^𝑐_1$ = 270K and $𝑇^𝑎_2$ = 160K, respectively. Remarkably, we observe diffuse x-ray scattering already near the higher transition temperature $𝑇^𝑐_1$ along 𝑎−CDW but at a slightly different wave vector q$^𝑎_1$ = (0.29,0,0). Inelastic x-ray scattering for Pd 0.01 ⁢ErTe 3 shows that a partial phonon softening at q$^𝑎_1$, underscoring the strong competition between ordering tendencies along the nearly equivalent in-plane axes of the orthorhombic lattice. For intercalation levels 𝑥 ≥ 0.02, the 𝑎−CDW state is suppressed. Nevertheless, a similar correlation between phonon softening and diffuse scattering persists along the [100] direction, again observed at q$^𝑎_1$ = (0.29,0,0) and $𝑇^𝑐_1$. These findings suggest that the 𝑎−CDW is fully suppressed for 𝑥 ≥ 0.02, and that the residual diffuse scattering at originates from the partial phonon softening associated with the 𝑐−CDW, reflected by the near equality of the absolute size of q$^𝑐_1$ and q$^𝑎_1$.

Maity, Avishek [Technische Univ. München, Garching↗