Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Surfaced Polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

X-ray Photon Correlation Spectroscopy Studies of Surfaces and Thin Films

The technique of X-ray Photon Correlation Spectroscopy (XPCS) is reviewed as a method for studying the relatively slow dynamics of materials on time scales ranging from microseconds to thousands of seconds and length scales ranging from microns down to nanometers. We focus on the application of this technique to study dynamical fluctuations of surfaces, interfaces and thin films. We first discuss instrumental issues such as the effects of partial coherence (or alternatively finite instrumental resolution) and optimization of signal-to-noise ratios in the experiments. We then review what has been learned from recent XPCS studies of capillary wave fluctuations on liquid surfaces and polymer films, of nanoparticles used as probes to study the interior dynamics of polymer films, of liquid crystals and multilamellar surfactant films, and of metal surfaces, and magnetic domain wall fluctuations in antiferromagnets. We then discuss studies of non-equilibrium dynamics described by 2-time correlation functions. Finally, we briefly speculate on possible future XPCS experiments at new synchrotron sources currently under development including studies of dynamics on time scales down to femtoseconds.

Sinha, Sunil K.↗

Electronic structure changes during the surface-assisted formation of a graphene nanoribbon

High conductivity and a tunability of the band gap make quasi-one-dimensional graphene nanoribbons (GNRs) highly interesting materials for the use in field effect transistors. Especially bottom-up fabricated GNRs possess well-defined edges which is important for the electronic structure and accordingly the band gap. In this study we investigate the formation of a sub-nanometer wide armchair GNR generated on a Au(111) surface. The on-surface synthesis is thermally activated and involves an intermediate non-aromatic polymer in which the molecular precursor forms polyanthrylene chains. Employing angle-resolved two-photon photoemission in combination with density functional theory calculations we find that the polymer exhibits two dispersing states which we attribute to the valence and the conduction band, respectively. While the band gap of the non-aromatic polymer obtained in this way is relatively large, namely 5.25 ± 0.06 eV, the gap of the corresponding aromatic GNR is strongly reduced which we attribute to the different degree of electron delocalization in the two systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interaction of Long-lived Reactive Species from Cold Atmospheric Pressure Plasma with Polymers: Chemical Modification by Ozone and Reactive Oxygen-Nitrogen Species

Atmospheric pressure plasma (APP) sources are able to generate a variety of reactive species that have different effects on materials, such as functionalization, etching and deposition. In this article, we study the effect of long-lived reactive neutral species on polymers using a model plasma-surface interaction (PSI) system that consists of ultra-thin (~10 nm) polystyrene (PS) films and a surface micro-discharge (SMD) reactor operated with various N 2 /O 2 working gas mixtures. We characterized and quantified the reactive species generated by SMD using IR and UV absorption, and we found that O 3 , N 2 O 5 , N 2 O and HNO 3 are the dominant long-lived reactants near the target surface. When exposing PS films to these reactive species, we observed material responses including film thickness expansion, surface and bulk oxidation, and surface organic nitrate formation. The quantity of these changes varied with the N 2 /O 2 working gas composition. By correlating material response with gas phase species, we find that the chemical modification of PS strongly depends on the density of O 3 in the gas phase, which is indicative of an essential role of O 3 in the remote APP treatment of polymers. Our results show that O 3 causes polymer surface oxidation, participates in the diffusion-reaction process in the polymer bulk, and results in aromatic ring cleavage and the formation of carbonyl groups. In contrast, we did not find a correlation between surface organic nitrate and individual long-lived reactive species mentioned above. This indicates that surface organic nitrate formation on polymer surfaces might result from the interaction of multiple reactive species, including O 3 and nitrogen containing species. A model for the interphase mass transfer of reactive species from gas to solid was also described.

36 MATERIALS SCIENCE↗

End-exclusion zones in strongly stretched, molten polymer brushes of arbitrary shape

Theories of strongly stretched polymer brushes, particularly the parabolic brush theory, are valuable for providing analytically tractable predictions for the thermodynamic behavior of surface-grafted polymers in a wide range of settings. Furthermore, the parabolic brush limit fails to describe polymers grafted to convex curved substrates, such as the surfaces of spherical nanoparticles or the interfaces of strongly segregated block copolymers. It has previously been shown that strongly stretched curved brushes require a boundary layer devoid of free chain ends, requiring modifications of the theoretical analysis. While this “end-exclusion zone” has been successfully incorporated into the descriptions of brushes grafted onto the outer surfaces of cylinders and spheres, the behavior of brushes on surfaces of arbitrary curvature has not yet been studied. We present a formulation of the strong-stretching theory for molten brushes on the surfaces of arbitrary curvature and identify four distinct regimes of interest for which brushes are predicted to possess end-exclusion zones, notably including regimes of positive mean curvature but negative Gaussian curvature. Through numerical solutions of the strong-stretching brush equations, we report predicted scaling of the size of the end-exclusion zone, the chain end distribution, the chain polarization, and the free energy of stretching with mean and Gaussian surface curvatures. Through these results, we present a comprehensive picture of how the brush geometry influences the end-exclusion zones and exact strong-stretching free energies, which can be applied, for example, to model the full spectrum of brush geometries encountered in block copolymer melt assembly.

36 MATERIALS SCIENCE↗

Stability and Surface Topography Evolution in Nanoimprinted Polymer Patterns under a Thermal Gradient

Nanostructures created in polymer films by nanoimprint lithography are subject to large stresses, both those from the imprinting processes as well as stresses arising from the intrinsic thermodynamic instabilities. These stresses can induce nanostructure deformation that can compromise the intended function of the imprinted pattern. Controlling these stresses, and thus the stability of the imprinted patterns, is a key scientific issue for this technology. The requirement of film stability against dewetting requires the use of entangled polymer films, which necessitates an understanding of complex viscoelastic response of these materials to large stresses. Here we investigate the evolution of the surface topography of nanoimprinted patterns in polystyrene films through a high throughput annealing approach in which the patterns are annealed for a fixed time on a controlled temperature gradient. Using principles of time-temperature superposition we systematically explore the effect of varying basic system variables such as pattern feature size, polymer molecular mass, imprinting temperature, on nanopattern stability and on the evolution of imprinted patterns driven by surface tension and internal stress. Nanostructure collapse generally occurs through a combination of a "slumping" instability, where the imprinted film simply relaxes towards a planar film and the film height decreases with time, and a lateral "zigzag" instability in the nanoimprinted lines.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Functionalization of polymer powders for SLS-processes using an atmospheric plasma jet in a fluidized bed reactor

Recently additive manufacturing processes such as selective laser sintering (SLS) of polymers have gained more importance for industrial applications [1]. Tailor-made modification of polymers is essential in order to make these processes more efficient and to cover the industrial demands. The so far used polymer materials show weak performance regarding the mechanical stability of processed parts. To overcome this limitation, a new route to functionalize the surface of commercially available polymer particles (PA12; PE-HD; PP) using an atmospheric plasma jet in combination with a fluidized bed reactor has been investigated. Consequently, an improvement of adhesion and wettability [2] of the polymer surface without restraining the bulk properties of the powder is achieved. The atmospheric plasma jet process can provide reactive species at moderate temperatures which are suitable for polymer material. The functionalization of the polymer powders improves the quality of the devices build in a SLS-process.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Recent Advances in LIBS for Real-Time Detection of Silicone Contaminants on CFRP Surfaces

Laser induced breakdown spectroscopy (LIBS) is a materials characterization technique that has been advanced and refined to provide in situ, real-time quality control of carbon fiber reinforced polymer (CFRP) surfaces. As part of an effort to improve process control for adhesive bonding, a LIBS system was designed and assembled at NASA Langley Research Center (LaRC) to enable detection of ultralow concentrations of silicone contamination on CFRP adherends. The LIBS instrument provides high sensitivity detection and quasi-nondestructive surface characterization of CFRP adherends prior to adhesive bonding. This review focuses on the advancements at LaRC using LIBS as a quality control tool for the detection of silicone contaminants for improved adhesive bonding reliability of CFRP materials. This work describes how the LIBS technique was advanced by analyzing the laser parameters, studying the laser-matter interactions, and performing time-resolved measurements to determine the optimal plasma conditions for elemental detection. In addition, LIBS results were compared to X-ray photoelectron spectroscopy data to enable quantitative analysis from analytical calibration curves. Examples are shown of how to perform surface mapping of silicone contamination. Finally, a brief discussion is also presented on LIBS instrumentation, recommendations for laser parameters and instrumentation components, and LIBS technique maturity.

Surface characterization, Carbon fiber reinforced ↗

Characterization of polymer decomposition products by laser desorption mass spectrometry

Laser desorption mass spectrometry has been used to characterize the ash-like substances formed on the surfaces of polymer matrix composites (PMC's) during exposure on LDEF. In an effort to minimize fragmentation, material was removed from the sample surfaces by laser desorption and desorbed neutrals were ionized by electron impact. Ions were detected in a time-of-flight mass analyzer which allows the entire mass spectrum to be collected for each laser shot. The method is ideal for these studies because only a small amount of ash is available for analysis. Three sets of samples were studied including C/polysulfone, C/polyimide and C/phenolic. Each set contains leading and trailing edge LDEF samples and their respective controls. In each case, the mass spectrum of the ash shows a number of high mass peaks which can be assigned to fragments of the associated polymer. These high mass peaks are not observed in the spectra of the control samples. In general, the results indicate that the ash is formed from decomposition of the polymer matrix.

Pallix, Joan B.↗

Durable and Versatile Immobilized Carbonic Anhydrase on Textile Structured Packing for CO 2 Capture

High-performance carbon dioxide (CO 2 )-capture technologies with low environmental impact are necessary to combat the current climate change crisis. Durable and versatile “drop-in-ready” textile structured packings with covalently immobilized carbonic anhydrase (CA) were created as efficient, easy to handle catalysts for CO 2 absorption in benign solvents. The hydrophilic textile structure itself contributed high surface area and superior liquid transport properties to promote gas-liquid reactions that were further enhanced by the presence of CA, leading to excellent CO 2 absorption efficiencies in lab-scale tests. Mechanistic investigations revealed that CO 2 capture efficiency depended primarily on immobilized enzymes at or near the surface, whereas polymer entrapped enzymes were more protected from external stressors than those exposed at the surface, providing strategies to optimize performance and durability. Textile packing with covalently attached enzyme aggregates retained 100% of the initial 66.7% CO 2 capture efficiency over 71-day longevity testing and retained 85% of the initial capture efficiency after 1-year of ambient dry storage. Subsequent stable performance in a 500 h continuous liquid flow scrubber test emphasized the material robustness. Biocatalytic textile packings performed well with different desirable solvents and across wide CO 2 concentration ranges that are critical for CO 2 capture from coal and natural gas-fired power plants, from natural gas and biogas for fuel upgrading, and directly from air.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Method of printing and implementing refractive X-ray optical components

A method of fabricating a refractive optical element on a substrate may provide less expensive and more compact optics for an X-ray system. The method includes coating the substrate with a resin and providing radiation to a portion of the resin to cause two photon polymerization of the resin. The method further includes forming, by two photon polymerization, a first surface of a polymer refractive optical element from the resin. The first surface is disposed along an optical axis of the refractive optical element and the first surface has a roughness of less than 100 nanometers. Further, the method includes forming, by two photon polymerization, a second surface of the polymer refractive optical element. The second surface is disposed along the optical axis of the refractive optical element and the second surface has a roughness of less than 100 nanometers.

Jiang, Zhang↗

Dispersion of modified fumed silica in elastomeric nanocomposites

In polymer nanocomposites, surface modification of silica aggregates can shield Coulombic interactions that inhibit agglomeration and formation of a network of agglomerates. Surface modification is usually achieved with silane coupling agents although carbon-coating during pyrolytic silica production is also possible. Pyrogenic silica with varying surface carbon contents were dispersed in styrene-butadiene (SBR) rubber to explore the impact on hierarchical dispersion, the emergence of meso-scale structures, and the rheological response. Pristine pyrogenic silica aggregates at concentrations above a critical value (related to the Debye screening length) display correlated meso-scale structures and poor filler network formation in rubber nanocomposites due to the presence of silanol groups on the surface. Here, in the present study, flame synthesized silica with sufficient surface carbon monolayers can mitigate the charge repulsion thereby impacting network structural emergence. The impact of the surface carbon on the van der Waals enthalpic attraction, a * , is determined. The van der Waals model for polymer nanocomposites is drawn through an analogy between thermal energy, k B T, and the accumulated strain, γ. The rheological response of the emergent meso-scale structures depends on the surface density of both carbon and silanol groups.

36 MATERIALS SCIENCE↗

Extreme Nanoconfinement Dramatically Enhances Small Molecule Solubility in Nonpolar Polymers

Elucidating gas solubility in confined polymer systems addresses a fundamental gap in polymer physics and has important implications for gas barrier and separation technologies and polymer upcycling reactions. In this study, we examine the solubility of methanol and n-hexane in polystyrene and low-density polyethylene confined within the interstitial pores of disordered silica nanoparticle packings. Using capillary rise infiltration, these polymers are infiltrated into the nanoparticle packings. Gas solubility in these confined polymers is measured using a quartz crystal microbalance. Remarkably, confinement leads to a 10- to ∼100-fold increase in gas solubility. Systematic experiments reveal that pore size plays a dominant role in increasing solubility. In contrast, the molecular weight of the polymer and the surface wetting characteristics of the nanoparticles, achieved by hydrophobically modifying the nanoparticles, have minimal effects. By systematically varying penetrant polarity, polymer crystallinity, pore size, and nanopore surface chemistry, this study isolates geometric nanoconfinement as the dominant factor governing solubility enhancement in confined polymers. Atomistic simulations revealed that confinement and surface−polymer interactions both contribute to enhanced solubility, with polymer packing playing a significant role in modulating gas uptake. Here, these results suggest that the changes in the molecular arrangements of polymer segments underlie the observed trends. This study highlights the potential of confined polymers in engineering the separation performance of membranes and heterogeneously catalyzed polymer upcycling reactions.

alcohols↗

Investigation of Polymetric Biofilms Formed by Dangerous Pathogens, and the Prevention of Their Formation by Disinfectants and Bacteriophages (CRADA Final Report)

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Intralytix Inc., to study biofilms formed on the surfaces of polymers by especially dangerous pathogens and nosocomial infections, to explore the possibility of decontamination of surfaces using different classes of disinfectants and specific bacteriophages. The research was conducted under the Global Initiative for Proliferation Prevention (GIPP) Program of DOE, the United States Industry Coalition, Inc. (USIC), and cooperating New Independent States (NIS) of the Former Soviet Union (FSU). The Russian institutes involved with this project were from Ukrainian I.I.Mechnikov Anti-Plague Science Research Institute (UAPRI), Odessa, Ukraine; and G. Eliava Institute of Bacteriophage, Microbiology and Virology of the Georgian Academy of Sciences (Eliava Institute), Tbilisi, Georgia. The technical objectives of this CRADA project were to develop novel bacteriophage preparations with polyvalent characteristics for use in variety of applications and useful for the treatment of antibiotic resistant pathogens and those associated with biofilm matrices. This would be achieved through the identification, testing and improvement of bacteriophages capable of lysing specific, targeted nosocomial and other pathogens with the above described properties.

Garcia, Emilio↗

Investigation of Polymetric Biofilms Formed by Dangerous Pathogens, and the Prevention of Their Formation by Disinfectants and Bacteriophages Final Report CRADA No. TC02145.0

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Intralytix Inc., to study biofilms formed on the surfaces of polymers by especially dangerous pathogens and nosocomial infections, to explore the possibility of decontamination of surfaces using different classes of disinfectants and specific bacteriophages.

59 BASIC BIOLOGICAL SCIENCES↗

An investigation of adhesive/adherend and fiber/matrix interactions. Part A: Surface characterization of titanium dioxide, titantium and titanium 6% Al to 4% V powders: Interaction with water, hydrogen chloride and polymers

The titanium dioxide surface is discussed. Polymer adhesive are also discussed. Titanium powders are considered. Characterization techniques are also considered. Interactions with polymers, water vapor, and HCl are reported. Adsorbents are characterized.

Siriwardane, R. V.↗