Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structural variation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Hyperspectral Remote Sensing of Foliar Nitrogen Content

A strong positive correlation between vegetation canopy bidirectional reflectance factor (BRF) in the near infrared (NIR) spectral region and foliar mass-based nitrogen concentration (%N) has been reported in some temperate and boreal forests. This relationship, if true, would indicate an additional role for nitrogen in the climate system via its influence on surface albedo and may offer a simple approach for monitoring foliar nitrogen using satellite data. We report, however, that the previously reported correlation is an artifact - it is a consequence of variations in canopy structure, rather than of %N. The data underlying this relationship were collected at sites with varying proportions of foliar nitrogen-poor needleleaf and nitrogen-rich broadleaf species, whose canopy structure differs considerably. When the BRF data are corrected for canopy-structure effects, the residual reflectance variations are negatively related to %N at all wavelengths in the interval 423-855 nm. This suggests that the observed positive correlation between BRF and %N conveys no information about %N. We find that to infer leaf biochemical constituents, e.g., N content, from remotely sensed data, BRF spectra in the interval 710-790 nm provide critical information for correction of structural influences. Our analysis also suggests that surface characteristics of leaves impact remote sensing of its internal constituents. This further decreases the ability to remotely sense canopy foliar nitrogen. Finally, the analysis presented here is generic to the problem of remote sensing of leaf-tissue constituents and is therefore not a specific critique of articles espousing remote sensing of foliar %N.

Knyazikhin, Yuri↗

Belt-zone variations in the Jovian cloud structure

Voyager Infrared Interferometer Spectrometer (IRIS) observations of Jupiter in the far infrared (180-1200/cm) are sensitive to emission originating from pressures less than 2 bars, while the 5-micrometer (1800-2300/cm) observations are primarily sensitive to emission originating from pressures greater than 2 bars. We use these differences in the location of the peak emission level to constrain the properties of the upper tropospheric cloud structure from the far-infrared observations and then use the 5-micrometer observations, with the upper tropospheric cloud structure fixed, to constrain the deep cloud structure. The relationship between observed 45- and 5-micrometer brightness temperatures reveals three distinct regions between +/- 25 deg latitude: North Equatorial Belt hot spots, which are 'hot' at both 45 and 5 micrometers; Equatorial Zone spectra, which are 'warm' at 45 micrometers and 'cold' at 5 micrometers; and North Tropical Zone spectra, which are 'cold' at both 45 and 5 micrometers. We find that the hot extreme spectral ensemble is unique to belts, and the cold extreme spectral ensembles are unique to zones, but that all other intermediate spectral ensembles are common to both regions. Analyses of these spectra using an anisotropic multiple scattering radiative transfer model reveal that the primary difference between belts and zones is the increased opacity and vertical extent of clouds in zones relative to their belt counterparts. In addition, we find a shift in the location of the para hydrogen gradient toward lower pressures in zones, with an increase in the 'equilibrated' cloud-top para fraction. We suggest that all of the variations in gas abundance profiles, temperature, and cloud structure are consistent with the effects of a simple mean circulation and large-scale wave motions.

Carlson, Barbara E.↗

Computational simulation of damping in composite structures

A computational methodology is developed for the prediction of passive damping in composite structures. The method involves multiple levels of damping modeling by integrating micromechanics, laminate, and structural damping theories. The effects of temperature and moisture on structural damping are included. The simulation of damping in the structural level is accomplished with finite-element discretization. Applications are performed on graphite/epoxy composite beams, plates, and shells to illustrate the methodology. Additional parametric studies demonstrate the variation of structural modal damping with respect to ply angles, fiber volume ratio, and temperature.

Saravanos, D. A.↗

Computational simulation of damping in composite structures

A computational methodology is developed for the prediction of passive damping in composite structures. The method involves multiple levels of damping modeling by integrating micromechanics, laminate, and structural damping theories. The effects of temperature and moisture on structural damping are included. The simulation of damping in the structural level is accomplished with finite-element discretization. Applications are performed on graphite/epoxy composite beams, plates, and shells to illustrate the methodology. Additional parametric studies demonstrate the variation of structural modal damping with respect to ply angles, fiber volume ratio, and temperature.

Saravanos, D. A.↗

Using BEEM To Probe Strains In Semiconductors

Ballistic-electron-emission microscopy (BEEM) useful in determining strains in semiconductors under some conditions. More specifically, BEEM is variant of scanning tunneling microscopy and sensitive to electronic structure of probed material. In present approach, BEEM used to obtain data on those aspects of variations in electronic structures related to variations in strains. Then by use of mathematical modeling of relationships between electronic structures and strains, variations in strains deduced from BEEM data.

Bell, L. Douglas↗

The use of radar and visual observations to characterize the surface structure of the planet Mercury

An analysis is conducted of available topographic profiles and scattering parameters derived from earth-based S- and X-band radar observations of Mercury, in order to determine the nature and origin of regional surface variations and structures that are typical of the planet. Attention is given to the proposal that intercrater plains on Mercury formed from extensive volcanic flooding during bombardment, so that most craters were formed on a partially molten surface and were thus obliterated, together with previously formed tectonic features.

Clark, P. E.↗

Synthesis and spectroscopic characterization of actinyl(VI) tetrahalide coordination compounds containing 2, 2'-bipyridine

A series of three new actinide tetrahalide coordination compounds containing 2,2'-bipyridinium (H 2 bpy) have been synthesized by room temperature evaporation and characterized via single crystal X-ray diffraction, Raman spectroscopy, and infrared spectroscopy. The solid-state compounds (Np1, U1, and U2) contain the AnO 2 2+ cation coordinated to four halide (chloride or bromide) atoms to form the anionic tetrahalide molecular unit [AnO 2 X 4 ] 2– (X = Cl, Br) and are charge balanced by the 2,2'-bipyridinium cations that engage in electrostatic interactions with the actinyl complex. Np1 (N 2 C 10 H 10 )[NpO 2 Cl 4 ] contains 2,2'-bipyridine in the cis conformation where both the nitrogen atoms are directed towards the [NpO 2 Cl 4 ] 2– monomer. Within U1 (N 2 C 10 H 9 )[UO 2 Cl 4 ], the 2,2'-bipyridine is in a trans conformation, and found in the same orientation in the isomorphous structure U2 (N 2 C 10 H 9 )[UO 2 Br 4 ]. The compounds were further characterized by vibrational spectroscopy with specific interest in the actinyl cation. Raman spectroscopy provided information on the actinyl symmetric stretch (ν 1 ) whereas IR spectroscopy is used to determine the location of the asymmetric stretch (ν 3 ). Here, spectral similarities are observed between the two isomorphous structures, but slight variations across the series of structures are found to be associated with bipyridine bands in the various conformations. Additional analysis of these vibrational features in U1 and U2 provided information on the actinyl force constants, allowing insight into the relative uranyl bond strength that was compared to similar tetrahalide compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural behavior of composites with progressive fracture

The objective of the study is to unify several computational tools developed for the prediction of progressive damage and fracture with efforts for the prediction of the overall response of damaged composite structures. In particular, a computational finite element model for the damaged structure is developed using a computer program as a byproduct of the analysis of progressive damage and fracture. Thus, a single computational investigation can predict progressive fracture and the resulting variation in structural properties of angleplied composites.

Minnetyan, L.↗

Observation of pressure ridges in SAR images of sea ice: Scattering theory and comparison with observations

Ridges and keels (hummocks and bummocks) in sea ice flows are important in sea ice research for both scientific and practical reasons. Sea ice movement and deformation is driven by internal and external stresses on the ice. Ridges and keels play important roles in both cases because they determine the external wind and current stresses via drag coefficients. For example, the drag coefficient over sea ice can vary by a factor of several depending on the fluid mechanical roughness length of the surface. This roughness length is thought to be strongly dependent on the ridge structures present. Thus, variations in ridge and keel structure can cause gradients in external stresses which must be balanced by internal stresses and possibly fracture of the ice. Ridging in sea ice is also a sign of fracture. In a practical sense, large ridges form the biggest impediment to surface travel over the ice or penetration through sea ice by ice-strengthened ships. Ridges also play an important role in the damage caused by sea ice to off-shore structures. Hence, observation and measurement of sea ice ridges is an important component of sea ice remote sensing. The research reported here builds on previous work, estimating the characteristics of ridges and leads in sea ice from SAR images. Our objective is to develop methods for quantitative measurement of sea ice ridges from SAR images. To make further progress, in particular, to estimate ridge height, a scattering model for ridges is needed. Our research approach for a ridge scattering model begins with a survey of the geometrical properties of ridges and a comparison with the characteristics of the surrounding ice. For this purpose we have used airborne optical laser (AOL) data collected during the 1987 Greenland Sea Experiment. These data were used to generate a spatial wavenumber spectrum for height variance for a typical ridge - the typical ridge is the average over 10 large ridges. Our first-order model radar scattering includes both the quasi-specular and Bragg resonant scatter mechanisms. This model is extended to include contributions from volume scatter and scatter from discrete objects. Geometrical characteristics from the AOL survey and model calculations imply that for radar wavelengths and observation geometries that are dominated by the quasi-specular scattering mechanism radar backscatter from a ridge is a measure of peak ridge height. We present scattering model results and compare them with ridges observed during the LEADEX experiment of March-April 1992 when both X, C, and L-band aircraft SAR and the ERS-1 satellite SAR observed a region in the Beaufort Sea near 86 deg N, 10 deg W. Data were also collected documenting ridge characteristics on the surface. The surface data are used to generate a SAR signature via the scattering model described above. The predicted SAR signatures compare well with the SAR observations.

Vesecky, J. F.↗

Effects of model deficiencies on parameter estimation

Reliable structural dynamic models will be required as a basis for deriving the reduced-order plant models used in control systems for large space structures. Ground vibration testing and model verification will play an important role in the development of these models; however, fundamental differences between the space environment and earth environment, as well as variations in structural properties due to as-built conditions, will make on-orbit identification essential. The efficiency, and perhaps even the success, of on-orbit identification will depend on having a valid model of the structure. It is envisioned that the identification process will primarily involve parametric methods. Given a correct model, a variety of estimation algorithms may be used to estimate parameter values. This paper explores the effects of modeling errors and model deficiencies on parameter estimation by reviewing previous case histories. The effects depend at least to some extent on the estimation algorithm being used. Bayesian estimation was used in the case histories presented here. It is therefore conceivable that the behavior of an estimation algorithm might be useful in detecting and possibly even diagnosing deficiencies. In practice, the task is complicated by the presence of systematic errors in experimental procedures and data processing and in the use of the estimation procedures themselves.

Hasselman, T. K.↗

Spectroscopic measurements of element abundances in the solar corona: Variations on the FIP theme

Solar wind and solar energetic particle (SEP) data yield systematic differences between elemental abundances in the corona and in the photosphere related to the first ionization potential (FIP) of the elements: low-FIP elements are preferentially enhanced relative to high-FIP elements by about a factor of four. Spectroscopic studies of the inner corona show that such a pattern may apply on average but not in detail for coronal loops: substantial abundance differences occur between different types of coronal structures, and variations have been found from flare to flare, from one active region to another, and over time in the same region; further, in some flares, anomalies such as enhanced Ne:O ratios, distinctly at odds with the FIP pattern, show that a competing element selection mechanism sometimes operates. Details of the observed abundance variability -- such as the magnitude of the variations, the relevant temporal and spatial scales, and correlations with other properties of the given coronal structure -- may give important clues to the processes which supply and heat the corona, or they may reflect the changing physical conditions or locations where those processes take place. However, many such details remain to be established definitively. At present, abundance variability is primarily a major complication to data analysis and interpretation. However, once it is better understood, it may provide a new diagnostic tool for probing the lower layers of the solar atmosphere.

Saba, J. L. R.↗

Vegetation structural complexity and biodiversity in the Great Smoky Mountains

Vegetation structural complexity and biodiversity tend to be positively correlated, but understanding of this relationship is limited in part by structural metrics tending to quantify only horizontal or vertical variation, and that do not reflect internal structure. We developed new metrics for quantifying internal vegetation structural complexity using terrestrial LiDAR scanning and applied them to 12 NEON forest plots across an elevational gradient in Great Smoky Mountains National Park, USA. We asked (1) How do our newly developed structure metrics compare to traditional metrics? (2) How does forest structure vary with elevation in a high-biodiversity, high topographic complexity region? (3) How do forest structural metrics vary in the strength of their relationships with vascular plant biodiversity? Our new measures of canopy density (Depth) and structural complexity (σDepth), and their canopy height-normalized counterparts, were sensitive to structural variations and effectively summarized horizontal and vertical dimensions of structural complexity. Forest structure varied widely across plots spanning the elevational range of GRSM, with taller, more structurally complex forests at lower elevation. Vascular plant biodiversity was negatively correlated with elevation and more strongly positively correlated with vegetation structure variables. The strong correlations we observed between canopy structural complexity and biodiversity suggest that structural complexity metrics could be used to assay plant biodiversity over large areas in concert with airborne and spaceborne platforms.

Jonathan A. Walter↗

Buckling of Thermoviscoelastic Structures Under Temporal and Spatial Temperature Variations

The problem of lateral instability of a viscoelastic in-plane loaded structure is considered in terms of thermorheolgically simple materials. As an example of a generally in-plane loaded structure, we examine the simple column under axial load: Both cyclic loading is considered (with constant or in-phase variable temperature excursions) as well as the case of constant load in the presence of thermal gradients through the thickness of the structure. The latter case involves a continuous movement of the neutral axis from the center to the colder side and then back to the center. In both cases, temperature has a very strong effect on the instability evolution, and under in-phase thermal cycling the critical loads are reduced compared to those at constant temperatures. The primary effect of thermal gradients beyond that of thermally-induced rate accelerations is occasioned by the generation of an "initial imperfection" or "structural bowing." Because the coefficient of thermal expansion tends to be large for many polymeric materials, it it may be necessary to take special care in lay-up design of composite structures intended for use under compressive loads in high-temperature applications. Finally, the implications for the temperature sensitivities of composites to micro-instability (fiber crimping) are also apparent from the results delineated here.

Tsuyuki, Richard↗

Correlations and contrasts in structural history and style between an Archaean greenstone belt and adjacent gneiss belt, NE Minnesota

An analysis of the deformation along the boundary between the Vermilion Granitic Complex (VGC) and the Vermilion district indicates that the two terranes have seen a similar deformation history since the earliest stages of folding in the area. Despite this common history, variations in structural style occur between the two terranes, such as the relative development of D sub 1 fabrics and D sub 2 shear zones, and these can be attributed to differences in the crustal levels of the two terranes during the deformation. Similarly, the local development of F sub 3 folds in the VGC, but not in the Vermilion district, is interpreted to be a result of later-D sub 2 pluton emplacement which was not significant at the level of exposure of ther Vermilion district.

Bauer, R. L.↗

High polarization InAlGaAs/AlGaAs photocathodes grown using MBE

Strained superlattices of GaAs/GaAsP grown using molecular beam epitaxy (MBE) have been used for more than 20 years to generate high polarization electron beams for nuclear physics. GaAs/GaAsP superlattices have several manufacturing challenges, including the thick graded layer required for the virtual GaAsP substrate, the significant difference in optimal growth temperatures for GaAs and GaAsP, and the scarcity of MBE systems using phosphorus. InAlGaAs/AlGaAs strained superlattice photocathode are an alternative structure that eliminates many of hurdles to growing GaAs/GaAsP in MBE systems. Measurements of quantum efficiency and polarization from InAlGaAs/AlGaAs will be presented. These include studies on a variety of growth parameters to optimize performance, including digital alloys, growth temperature variations, and variation in structure.

Stutzman, Marcy L↗

Integrated aeroservoelastic tailoring of lifting surfaces

An approach to the integration of two design activities, structural design and active control design, for a highly idealized aeroservoelastic system is presented. The particular design goal for this study is the maximization of the stable airspeed envelope of an idealized model of an aeroservoelastic system through rational and systematic variation of structural and control design parameters. The steady-state linear quadratic regulator is used to model the control subsystem; the structural subsystem is assigned characteristic design parameters, such as shear center position. The application of the procedure described here produces optimally controlled structures with stability characteristics superior to those of open-loop and initial closed-loop designs.

Zeiler, T. A.↗

Solution accuracies of finite element reentry heat transfer and thermal stress analyses of Space Shuttle Orbiter

Accuracies of solutions (structural temperatures and thermal stresses) obtained from different thermal and structural FEMs set up for the Space Shuttle Orbiter (SSO) are compared and discussed. For studying the effect of element size on the solution accuracies of heat-transfer and thermal-stress analyses of the SSO, five SPAR thermal models and five NASTRAN structural models were set up for wing midspan bay 3. The structural temperature distribution over the wing skin (lower and upper) surface of one bay was dome shaped and induced more severe thermal stresses in the chordwise direction than in the spanwise direction. The induced thermal stresses were extremely sensitive to slight variation in structural temperature distributions. Both internal convention and internal radiation were found to have equal effects on the SSO.

Ko, William L.↗

Structural behavior of composites with progressive fracture

Structural characteristics such as natural frequencies and buckling loads with corresponding mode shapes were investigated during progressive fracture of multilayer, angle-plied polymer matrix composites. A computer program was used to generate the numerical results for overall mechanical response of damaged composites. Variations in structural characteristics as a function of the previously applied loading were studied. Results indicate that most of the overall structural properties were preserved throughout a significant proportion of the ultimate fracture load. For the cases studied, changes in structural behavior began to occur after 70 percent of the ultimate fracture load was applied. However, the individual nature of the structural change was rather varied depending on the laminate configuration, fiber orientation, and the boundary conditions.

Minnetyan, Levon↗