Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Microstructural development and mechanical properties of a near-eutectic directionally solidified Sn–Bi solder alloy

Sn–Bi solders may be applied for electronic applications where low-temperature soldering is required, i.e., sensitive components, step soldering and soldering LEDs. In spite of their potential to cover such applications, the mechanical response of soldered joints of Sn–Bi alloys in some cases does not meet the strength requirements due to inappropriate resulting microstructures. Hence, careful examination and control of as-soldered microstructures become necessary with a view to pre-programming reliable final properties. The present study aims to investigate the effects of solidification thermal parameters (growth rate — V{sub L} and cooling rate — T-dot{sub L}) on the microstructure of the Sn–52 wt.%Bi solder solidified under unsteady-state conditions. Samples were obtained by upward directional solidification (DS), followed by characterization through metallography and scanning electron microscopy (SEM). The microstructures are shown to be formed by Sn-rich dendrites decorated with Bi precipitates surrounded by a complex regular eutectic mixture, with alternated Bi-rich and Sn-rich phases. Experimental correlations of primary (λ{sub 1}), secondary (λ{sub 2}), tertiary (λ{sub 3}) dendritic and eutectic spacings (λ{sub coarse} and λ{sub fine}) with cooling rate and growth rate are established. Two ranges of lamellar eutectic sizes were determined, described by two experimental equations λ = 1.1 V{sub L}{sup −1/2} and λ = 0.67 V{sub L}{sup −1/2}. The onset of tertiary branches within the dendritic array along the Sn–52 wt.%Bi alloy DS casting is shown to occur for cooling rates lower than 1.5 °C/s. - Highlights: • The Sn–52 wt.%Bi solder was shown to have two eutectic sizes. • The fishbone eutectic is preferably located adjacent to the Bi-rich lamellar phases. • The onset of tertiary dendritic branches in Sn–Bi is associated with T-dot{sub L} < 1.5 °C/s. • Higher eutectic fraction and λ{sub 3} provoked a reverse increase in σ{sub u} and σ{sub y}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multiscale Modeling of Microstructural Evolution in Fused-Coating Additive Manufacturing

A quantitative phase field model with adaptive-computational-domain-expansion (ACDE) method was developed to simulate the microstructural evolution in fused-coating additive manufacturing process. A heat transfer and fluid flow model was established to investigate the solidification behavior of the molten pool in a single deposited layer. The solidification parameters such as temperature gradient and solidification rate were calculated from the macroscopic model and then fed into the phase field model to get the microstructure at different positions within a single deposited layer. Columnar dendrites were formed at the bottom of the deposited layer, and equiaxed dendrites appeared in the upper part of the layer. The ACDE method is used to improve the simulation efficiency. The metallographic experiments and energy-dispersive spectrometer analysis for composition were conducted on the fused-coating specimen, and the results were in good accordance with the simulations.

36 MATERIALS SCIENCE↗

Small-scale mechanical behavior of intermetallics and their composites

To model and predict the mechanical behavior of composite materials, knowledge of the properties of their constituent phases as well as how they interact with each other is required. Although these mechanical properties can sometimes be deduced from measurements on bulk specimens, it is not always possible due to difficulties in producing bulk materials with compositions and structures similar to those of the individual phases in the composite. In such cases, in situ measurements of mechanical properties are needed. We review here our recent work on the application of nanoindentation and neutron diffraction to investigate the in situ mechanical responses of Cr-Cr{sub 3}Si and NiAl-Mo, two model eutectic composites that were chosen because they can be processed by directional solidification to yield well-aligned lamellar and fibrous microstructures. Phase-specific mechanical properties were measured and correlated with bulk behavior. We will discuss recently developed techniques that improve the accuracy of mechanical property measurements at small microstructural length scales.

36 MATERIALS SCIENCE↗

Fracture toughness and corrosion resistance of semisolid AlSi5 alloy

The aim of this work was to investigate fracture toughness and corrosion resistance of semisolid AlSi5 castings, compared to samples obtained from conventional casting operations. In order to have a semisolid microstructure, the melt alloy was treated by means of ultrasound during solidification and then poured into permanent moulds. Mechanical properties of semisolid and conventional castings were compared by means of ultimate tensile strength (R{sub m}), yield stress (Rp{sub 02}) and hardness (HV) measurements. Fracture mechanics tests were carried out on Single Edge Notched Bend (SENB) specimens, machined from castings, and pre-cracked by fatigue. These tests were performed to determine the effect of the microstructure on the J-Integral resistance (J-R) behavior and to deeply understand the ductile fracture behaviour of semisolid parts. The J-Integral versus spaced crack extension (J-{Delta}a) curves showed an improved resistance of the semisolid microstructure, due to the higher ductility. Finally, the corrosion behaviour of semisolid samples was compared to that of castings coming from solidification of fully liquid alloy by means of electrochemical potentiodynamic polarization tests. It was observed that the globular microstructure offers better quality, in terms of higher mechanical properties, as a consequence of a more uniform distribution of the solute.

36 MATERIALS SCIENCE↗

Examination of the solidification macrostructure of spheroidal and flake graphite cast irons using DAAS and ESBD

This investigation focuses on the study of the solidification macrostructure of sand cast flake and spheroidal graphite cast irons. The macrostructure is revealed by using a special technique developed earlier by the authors, called Direct Austempering After Solidification. The observations make use of conventional metallography and Electron Back Scattering Diffraction. The latter technique allows a more detailed observation of the morphology of the austenite grains and the microstructure of the matrix. The results of Electron Back Scattering Diffraction validate the observations made using the macrographic technique. It is verified that the solidification of both flake and spheroidal graphite cast irons is dominated by the growth of large austenite dendrites that form a grain pattern similar to that usually found in most metallic alloys.

36 MATERIALS SCIENCE↗

Effect of process parameters on hardness, temperature profile and solidification of different layers processed by direct metal laser sintering (DMLS)

In DMLS process objects are fabricated layer by layer from powdered material by melting induced by a controlled laser beam. Metallic powder melts and solidifies to form a single layer. Solidification map during layer formation is an important route to characterize micro-structure and grain morphology of sintered layer. Generally, solidification leads to columnar, equiaxed or mixture of these two types grain morphology depending on solidification rate and thermal gradient. Eutectic or dendritic structure can be formed in fully equiaxed zone. This dendritic growth has a large effect on material properties. Smaller dendrites generally increase ductility of the layer. Thus, materials can be designed by creating desired grain morphology in certain regions using DMLS process. To accomplish this, hardness, temperature distribution, thermal gradient and solidification cooling rate in processed layers will be studied under change of process variables by using finite element analysis, with specific application to Ti-6Al-4V.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Phase-field investigation on the non-equilibrium interface dynamics of rapid alloy solidification

The research program reported here is focused on critical issues that represent conspicuous gaps in current understanding of rapid solidification, limiting our ability to predict and control microstructural evolution (i.e. morphological dynamics and microsegregation) at high undercooling, where conditions depart significantly from local equilibrium. More specifically, through careful application of phase-field modeling, using appropriate thin-interface and anti-trapping corrections and addressing important details such as transient effects and a velocity-dependent (i.e. adaptive) numerics, the current analysis provides a reasonable simulation-based picture of non-equilibrium solute partitioning and the corresponding oscillatory dynamics associated with single-phase rapid solidification and show that this method is a suitable means for a self-consistent simulation of transient behavior and operating point selection under rapid growth conditions. Moving beyond the limitations of conventional theoretical/analytical treatments of non-equilibrium solute partitioning, these results serve to substantiate recent experimental findings and analytical treatments for single-phase rapid solidification. The departure from the equilibrium solid concentration at the solid-liquid interface was often observed during rapid solidification, and the energetic associated non-equilibrium solute partitioning has been treated in detail, providing possible ranges of interface concentrations for a given growth condition. Use of these treatments for analytical description of specific single-phase dendritic and cellular operating point selection, however, requires a model for solute partitioning under a given set of growth conditions. Therefore, analytical solute trapping models which describe the chemical partitioning as a function of steady state interface velocities have been developed and widely utilized in most of the theoretical investigations of rapid solidification. However, these solute trapping models are not rigorously verified due to the difficulty in experimentally measuring under rapid growth conditions. Moreover, since these solute trapping models include kinetic parameters which are difficult to directly measure from experiments, application of the solute trapping models or the associated analytic rapid solidification model is limited. These theoretical models for steady state rapid solidification which incorporate the solute trapping models do not describe the interdependency of solute diffusion, interface kinetics, and alloy thermodynamics. The phase-field approach allows calculating, spontaneously, the non-equilibrium growth effects of alloys and the associated time-dependent growth dynamics, without making the assumptions that solute partitioning is an explicit function of velocity, as is the current convention. In the research described here, by utilizing the phase-field model in the thin-interface limit, incorporating the anti-trapping current term, more quantitatively valid interface kinetics and solute diffusion across the interface are calculated. In order to sufficiently resolve the physical length scales (i.e. interface thickness and diffusion boundary length), grid spacings are continually adjusted in calculations. The full trajectories of transient planar growth dynamics under rapid directional solidification conditions with different pulling velocities are described. As a validation of a model, the predicted steady state conditions are consistent with the analytic approach for rapid growth. It was confirmed that rapid interface dynamics exhibits the abrupt acceleration of the planar front when the effect of the non-equilibrium solute partitioning at the interface becomes signi ficant. This is consistent with the previous linear stability analysis for the non-equilibrium interface dynamics. With an appropriate growth condition, the continuous oscillation dynamics was able to be simulated using continually adjusting grid spacings. This oscillatory dynamics including instantaneous jump of interface velocities are consistent with a previous phenomenological model by and a numerical investigation, which may cause the formation of banded structures. Additionally, the selection of the steady state growth dynamics in the highly undercooled melt is demonstrated. The transition of the growth morphology, interface velocity selection, and solute trapping phenomenon with increasing melt supersaturations was described by the phase-field simulation. The tip selection for the dendritic growth was consistent with Ivantsov's function, and the non-equilibrium chemical partitioning behavior shows good qualitative agreement with the Aziz's solute trapping model even though the model parameter(V D ) remains as an arbitrary constant. This work is able to show the possibility of comprehensive description of rapid alloy growth over the entire time-dependent non-equilibrium phenomenon.

36 MATERIALS SCIENCE↗

Developing of nano sized fibrous eutectic silicon in hypereutectic Al–Si alloy by laser remelting

Laser surface melting followed by rapid solidification is an effective means to produce very fine microstructures with desirable surface properties because of the high rates of cooling associated with it. In the present study, the effect of rapid cooling on the silicon particle size, distribution, and morphology of hypereutectic Al–17wt.%Si and Al–20wt.%Si alloys have been investigated. A continuous-wave CO2 laser of wavelength 10.6 μm and a Trumpf Yb-YAG disk laser of wavelength 1.030 μm were used with a beam diameter of 1 mm and scanning speeds ranging from 5 to 100 mm/s. Rapid solidification increased the solubility of silicon in aluminum to approximately 5wt% and induced non-equilibrium hypoeutectic microstructures comprising large volume fractions of primary α-Al dendrites and ultrafine Al–Si eutectic of lamellar morphology. Both α-Al dendrites and the silicon particle sizes were significantly reduced from micron to nanoscale level. The morphology of silicon particles is modified from massive polygonal and plate-like to a mixture of fine fakes with round corners, feathery and fibrous, or a coral-like and thread-like structure. The eutectic silicon size and the interlamellar spacing were reduced to 30 and 10 nm, respectively. Furthermore, most of the silicon crystals in the eutectic region and the aluminum dendrites contained a significant number of twins which were considered as an essential contributor to the mechanism of growth and branching. Microhardness values increased two to threefold due to the refinement of the microstructural constituent.

42 ENGINEERING↗

Gas atomized chemical reservoir ODS ferritic stainless steels

Gas atomization reaction synthesis was used to surface oxidize ferritic stainless steel powders (i.e., Fe-16.0Cr-(0.1-0.2)Y-(0.1-0.5)(Ti or Hf) at.%) during the primary break-up and solidification of the molten alloy. This rapid surface reaction resulted in envelopment of the powders by an ultra thin (i.e., t < 100nm) metastable Cr-enriched oxide shell. This metastable oxide phase was subsequently dissociated, and used as an oxygen reservoir for the formation of more thermodynamically favored Y-(Ti,Hf) nano-metric oxide precipitates during elevated temperature heat treatment of the as-consolidated powders. This oxygen exchange reaction promoted the formation of nano-metric oxide dispersoids throughout the alloy microstructure. The atomization processing parameters were adjusted to tailor the oxygen content in as-atomized powders. Microstructure phase analysis was completed using transmission electron microscopy and X-ray powder diffraction.

36 MATERIALS SCIENCE↗

Pulsed laser powder bed fusion additive manufacturing of A356

Highlights: • Dense A356 specimens (98 ± 0.4%) were fabricated using a customized P-LPBF system. • Microstructure and grain morphology were examined using LOM, SEM, and EBSD. • Solidification front velocities (R) were evaluated through the KGT model. • A columnar grain structure was observed and predicted by the Hunt's criterion. - Abstract: A356 (Al7SiMg) specimens were fabricated through pulsed laser powder bed fusion (P-LPBF) additive manufacturing. Microstructural examinations and analyses were carried out through the usage of light optical microscopy (LOM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The results revealed a fine cellular microstructure with the intercellular network consisting of Al cells and defined by a network of Si arms. The Al cells at the center of the melt pools and within the melt pool boundary bands were measured to be 423 ± 49 nm and 664 ± 76 nm, respectively. The presence of a fine columnar grain structure and epitaxial growth on partially melted grains was observed and explained by the KGT model and Hunt's criterion.

36 MATERIALS SCIENCE↗

A scalable framework for efficient coupling of thermal and microstructural simulations in additive manufacturing

Predicting microstructure evolution in metal additive manufacturing (AM) is important for process optimization, but spatiotemporal scale disparities between thermal transport and microstructure evolution create significant challenges for efficient data transfer between simulation codes. To address this, we present Stork, a scalable framework for coupling thermal and microstructural simulations. Stork uses a sparse data representation to identify and store active solidification sub-volumes, enabling highly parallel quad-linear interpolation from coarse thermal grids to fine microstructure grids without large intermediate storage. We demonstrate the framework by coupling the semi-analytic heat transfer code 3DThesis with the time-parallel cellular automata code Toucan. This approach achieves over two orders of magnitude reduction in data generation time and file size compared to prior workflows. Numerical studies show that quad-linear interpolation preserves grain morphology and crystallographic texture in laser powder bed fusion (LPBF) simulations for coarsening ratios up to 16. Overall, Stork provides a scalable pathway for high-throughput, component-scale AM simulations on modern high-performance computing systems.

36 MATERIALS SCIENCE↗

Outlook on texture evolution in additively manufactured stainless steels: Prospects for hydrogen embrittlement resistance, overview of mechanical, and solidification behavior

Abstract Realizing application specific manufacture with fusion-based additive manufacturing (F-BAM) processes requires understanding of the physical phenomena that drive evolution of microstructural attributes, such as texture. Current approaches for understanding texture evolution in F-BAM are majorly considerate of the phenomena occurring only during solidification. This hinders the comprehensive understanding and control of texture during F-BAM. In this perspective article, we discuss several physical phenomena occurring during and after solidification that can determine texture in F-BAM processed stainless steels (SS). A crystal plasticity-coupled hydrogen adsorption-diffusion modeling framework is also leveraged to demonstrate the prospects of grain boundary engineering with F-BAM for enhanced hydrogen embrittlement resistance of SS. Implications of varying thermokinetics in F-BAM for solidification behavior of SS are discussed. Additionally, microstructural attributes that are key to high temperature mechanical performance of SS are highlighted. Considerations as outlined in this perspective article will enable grain boundary engineering and application specific microstructural design of SS with F-BAM. Graphical abstract

36 MATERIALS SCIENCE↗

Microstructure evolution during binder jet additive manufacturing of H13 tool steel

H13 is one of the most used tool steels for both hot and cold work tooling applications. Binder jet additive manufacturing offers the potential to deposit complex tools at scale due to larger powder bed sizes and faster deposition rates. However, to date there is no published literature on the sintering of H13 to full densification. Here, we discuss the pressureless sintering of binder jet AM H13 steel to full densification via supersolidus liquid phase sintering (SLPS) while presenting appropriate process windows (1360 °C – 1380 °C) for densification without distortion. The process windows have been rationalized based on thermodynamic calculations of liquid volume fractions with temperature. We show that higher binder saturation results in higher carbon retention and subsequently early liquid formation that can initiate the sintering process at lower temperatures. We report abnormal grain growth during sintering and found that the solidification phase transformations play a critical role on microstructural evolution and must be considered to accurately model the kinetics of SLPS.

36 MATERIALS SCIENCE↗

Effects of Copper Content and Mold Temperature on the Hot Tearing Susceptibility of Mg-7Zn-xCu-0.6Zr Alloys

The effects of copper (Cu) content and mold temperature on the hot tearing susceptibility (HTS) of Mg-7Zn-xCu-0.6Zr (x = 0, 1, 2) alloys were investigated experimentally using a T-type hot tearing mold. The crack volumes were measured by paraffin permeation method, and the solidification process was analyzed by thermal analysis and by using the Clyne and Davies model. The microstructure and morphology of the crack zone of Mg-7Zn-xCu-0.6Zr alloys were characterized by scanning electron microscopy, and the composition of alloys was analyzed by X-ray diffraction. The results showed the formation of a new phase of MgZnCu in the alloys with Cu addition. Moreover, addition of Cu also led to the refinement of microstructures of Mg-7Zn-xCu-0.6Zr alloys. The HTS of Mg-7Zn-xCu-0.6Zr alloys decreased with the increase in both the content of Cu and the mold temperature.

36 MATERIALS SCIENCE↗

Formation mechanism of atomic cluster structures in Al-Mg alloy during rapid solidification processes

The rapid solidification processes of Al{sub 50}Mg{sub 50} liquid alloy consisting of 50,000 atoms have been simulated by using molecular dynamics method based on the effective pair potential derived from the pseudopotential theory. The formation mechanisms of atomic clusters during the rapid solidification processes have been investigated adopting a new cluster description method-cluster-type index method (CTIM). The simulated partial structure factors are in good agreement with the experimental results. And Al-Mg amorphous structure characterized with Al-centered icosahedral topological short-range order (SRO) is found to form during the rapid solidification processes. The icosahedral cluster plays a key role in the microstructure transition. Besides, it is also found that the size distribution of various clusters in the system presents a magic number sequence of 13, 19, 23, 25, 29, 31, 33, 37, .... The magic clusters are more stable and mainly correspond to the incompact arrangements of linked icosahedra in the form of rings, chains or dendrites. And each magic number point stands correspondingly for one certain combining form of icosahedra. This magic number sequence is different from that generated in the solidification structure of liquid Al and those obtained by methods of gaseous deposition and ionic spray, etc.

36 MATERIALS SCIENCE↗

Dendritic deformation modes in additive manufacturing revealed by operando x-ray diffraction

Abstract Dynamic solidification behavior during metal additive manufacturing directly influences the as-built microstructure, defects, and mechanical properties of printed parts. How the formation of these features is driven by temperature variation (e.g., thermal gradient magnitude and solidification front velocity) has been studied extensively in metal additive manufacturing, with synchrotron x-ray imaging becoming a critical tool to monitor these processes. Here, we extend these efforts to monitoring full thermomechanical deformation during solidification through the use of operando x-ray diffraction during laser melting. With operando diffraction, we analyze thermomechanical deformation modes such as torsion, bending, fragmentation, assimilation, oscillation, and interdendritic growth. Understanding such phenomena can aid the optimization of printing strategies to obtain specific microstructural features, including localized misorientations, dislocation substructure, and grain boundary character. The interpretation of operando diffraction results is supported by post-mortem electron backscatter diffraction analyses.

Dass, Adrita (ORCID:000000019100635X)↗

Optimization of WAAM Process to Produce AUSC Components with Increased Service Life

Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Wire Arc Additive manufacturing (WAAM) process is a class of directed energy deposition process enabling higher build rate and allowing custom wire feedstock allowing spatial variation of microstructure. The larger spot size and lower speed creates a larger melt pool, reducing residual stress and often time creating directional/columnar microstructure for Ni-superalloy. The use of flexible platform provides freedom in deposition strategy, which can accommodate complex substrates, including feature addition onto existing structures, non-flat layers, and repair methods. However, the certification of the final component needs to match the strength requirement. Hence, the quality of the component produced is stringently monitored to avoid buildup of residual stress, cracks, porosity and to reduce detrimental segregated phases commonly observed during alloy solidification. Simulation plays a huge role in predicting the melt pool dimension and can be used to optimize the process parameter. Similar development is also required to perform physics-based modeling of microstructural development in WAAM that can predict the microstructural features during solidification and can be used to optimize the process more effectively. To move toward this goal, Raytheon Technologies Research Center together with Siemens worked to create a set of computational tools to control the process parameters, enable on-line measurements and acquisition with feedback to the optimized process parameters, and eventually track material evolution through each step of the additive process. Computational fluid dynamics is used for accurate prediction and calibration of the thermal field during WAAM process. and phase field models for microstructure evolution as a function of processing parameters to establish a connection between additive parameters and the final microstructure. Here we report cellular automata (CA) model development to predict the dendritic microstructure evolution with surface and bulk nuclei for single track and multiple layers. The CA model was developed to account for secondary element addition and predict segregation, local melting, and latent heat release as well as prediction of Euler angles from orientation information and validated against experiments. This framework was utilized to tailor spatially-varying composition in a part by appropriately controlling the microstructure evolution during the additive process. Functionally graded Haynes 282 alloy with high Cr content at the surface was tested for oxidation and mechanical properties. An advanced physics-based reaction-diffusion model predicting the simultaneous creation of chromium oxide and alumina is developed and validated to extend life expectancy of the WAAM manufactured high temperature part. A machine-learning data-driven framework establishing the process-structure relationship from a dataset of real microstructure images and corresponding process history data has been developed and implemented in the NX Siemens design system. The digital twin configuration along with the tool path generation enabled prediction of WAAM component buildup time and the techno-economic analysis provided a favorable option for all 4 cases with 15-40% cost reduction.

33 ADVANCED PROPULSION SYSTEMS↗