Fabrication and Performance of Separately-Biasable Antiparallel-Pair
A 210 MHz waveguide subharmonically-pumped mixer with integrated antiparallel-pair planar.
antiparallel-pair planar T-anode bias circuit T-ga↗
SEARCH · Engineering Papers
Results for “Separation circuit”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of single cell protectors for sealed silver-zinc cells, phase 1
A single cell protector (SCP) assembly capable of protecting a single silver-zinc (Ag Zn) battery cell was designed, fabricated, and tested. The SCP provides cell-level protection against overcharge and overdischarge by a bypass circuit. The bypass circuit consists of a magnetic-latching relay that is controlled by the high and low-voltage limit comparators. Although designed specifically for secondary Ag-Zn cells, the SCP is flexible enough to be adapted to other rechargeable cells. Eighteen SCPs were used in life testing of an 18-cell battery. The cells were sealed Ag-Zn system with inorganic separators. For comparison, another 18-cell battery was subjected to identical life test conditions, but with battery-level protection rather than cell-level. An alternative approach to the SCP design in the form of a microprocessor-based system was conceptually designed. The comparison of SCP and microprocessor approaches is also presented and a preferred approach for Ag-Zn battery protection is discussed.
Imamura, M. S.↗
Flow improvements in the NASA Langley 4- by 7-meter tunnel circuit
The mean velocity profiles in both the horizontal and vertical planes of symmetry at specific locations throughout the tunnel circuit to identify the most promising means for improving the flow in the 4 by 7 meter wind tunnel were measured. In the base line tunnel flow surveys, the flow patterns near the end of the test section indicate a uniform mean velocity distribution. Downstream of the test section, unsymmetrical flow patterns result in low velocities along the inner walls and in flow separation along the inner wall of the diffuser upstream of the drive fan and along the outer wall of the large diffuser downstream of the drive fan. A set of trailing-edge flaps attached to the five flow-control vanes located just downstream of the first corner were installed. These flaps are successful in making the tunnel flow more symmetrical and in eliminating the regions of separation in the diffusers upstream and downstream of the drive fan. Previously announced in STAR as N84-15117
Applin, Z. T.↗
Programmable Maintenance Processor For XAIDS
Programmable maintenance processor (MAINT) made of commercially available integrated circuits. Autonomous one of four digital electronic processors in extended aircraft interrogation and display system (XAIDS). Developed for testing of system and application computer programs as well as for testing equipment. MAINT has independent terminal and printer interfaces and dedicated magnetic bubble memory storing system-testing sequences entered from terminal. Software for MAINT written in PLM86 programming language and broken into four separate modules.
Glover, Richard↗
Measurement of minority carrier lifetimes and surface recombination velocities in solar cells
A generic comparison has been carried out of all methods for recombination parameter determination that are based on measurement of a current and/or voltage in either steady-state, transient, or frequency-dependent approaches. The theoretical background for the time-dependent methods has been extended from prior work to include drift fields and be applicable to compound (multilayered) regions. The key findings were: (1) all methods have essentially the same limitations to determination of only the dominant recombination parameters; (2) open-circuit measurements have more sensitivity to the recombination parameters than short circuit measurements, but they present much more difficulty in eliminating spurious effects; (3) transient and frequency-dependent methods have exactly the same expressions for the relaxation constants and the breakpoint frequencies; and (4) in compound regions there exists only one set of relaxation constants for all the coupled layers. These constants include all relevant parameters of these layers. It is thus difficult to separate these parameters in time- or frequency-domain measurements. ASLBIC seems still to be the most suitable method for determination of emitter parameters.
Wolf, M.↗
Investigations of detail design issues for the high speed acoustic wind tunnel using a 60th scale model tunnel. Part 2: Tests with the closed circuit
This report summarizes the tests on the 1:60 scale model of the High Speed Acoustic Wind Tunnel (HSAWT) performed during the period June - August 1991. Throughout the testing the tunnel was operated in the 'closed circuit mode,' that is when the airflow was set up by an axial flow fan, which was located inside the tunnel circuit and was directly driven by a motor. The tests were first performed with the closed test section and were subsequently repeated with the open test section, the latter operating with the nozzle-diffuser at its optimum setting. On this subject, reference is made to the report (1) issued January 1991, under contract 17-GFY900125, which summarizes the result obtained with the tunnel operating in the 'open circuit mode.' The tests confirmed the viability of the tunnel design, and the flow distributions in most of the tunnel components were considered acceptable. There were found, however, some locations where the flow distribution requires improvement. This applies to the flow upstream of the fan where the flow was found skewed, thus affecting the flow downstream. As a result of this, the flow appeared separated at the end of the large diffuser at the outer side. All tests were performed at NASA LaRC.
Barna, P. Stephen↗
Equatorward shift of the cusp during magnetospheric substorms
The equatorward shift of the midday part of the auroral oval (the cusp region) during the expansion phase of magnetospheric substorms is reexamined. A magnetospheric model developed by Akasofu and Corrick (1980) is used, which is constructed by using the earth's dipole field, an image dipole field of the earth and 40 bisected circular loops. A new dayside current system represented by six current loops separated by 15 deg in longitude, each carrying 100 KA, is added to this model. For a total current of .6 MA, the latitude of the cusp shifts equatorward by 1.8 deg; for a current of 1.8 MA, the cusp location shifts by more than 5 deg. Thus, the magnetic field of an enhanced dynamo current is the dayside boundary layer and of the connected circuit can account for the observed equatorward shift of the cusp region.
Akasofu, S.-I.↗
Processing technology for high efficiency silicon solar cells
Recent advances in silicon solar cell processing have led to attainment of conversion efficiency approaching 20%. The basic cell design is investigated and features of greatest importance to achievement of 20% efficiency are indicated. Experiments to separately optimize high efficiency design features in test structures are discussed. The integration of these features in a high efficiency cell is examined. Ion implantation has been used to achieve optimal concentrations of emitter dopant and junction depth. The optimization reflects the trade-off between high sheet conductivity, necessary for high fill factor, and heavy doping effects, which must be minimized for high open circuit voltage. A second important aspect of the design experiments is the development of a passivation process to minimize front surface recombination velocity. The manner in which a thin SiO2 layer may be used for this purpose is indicated without increasing reflection losses, if the antireflection coating is properly designed. Details are presented of processing intended to reduce recombination at the contact/Si interface. Data on cell performance (including CZ and ribbon) and analysis of loss mechanisms are also presented.
Spitzer, M. B.↗
Performance, Stability and Compatibility of Oxygen/RP-1 Multi-Element Oxidizer-Rich Staged-Combustion Injectors
In 2015 and 2016, the National Aeronautics and Space Administration Marshall Space Flight Center designed, fabricated, assembled and hot-fire tested an oxygen/RP-1 propellant multi-element oxidizer-rich staged-combustion test article. The main objective was to provide thrust chamber combustion stability data as part of the Combustion Stability Tool Development program, although demonstration of performance and compatibility of oxidizer-rich main injectors was also important. Funding was provided by the Air Force Space and Missile Systems Center. Five configurations of main injectors were designed and fabricated, using conventional gas-centered swirl coaxial injector element designs generally similar to those used in oxygen/kerosene oxidizer-rich staged combustion engines such as the Russian RD-180 or NK-33 engines. Variations of element features included element size, recess depth, fuel gap width, and the presence of the sleeve separating the swirling fuel flow from the axial oxidizer flow. Ablative combustion chambers were fabricated based on hardware previously used at the NASA MSFC for testing at similar size and pressure. Existing oxygen/RP-1 oxidizer-rich subscale preburner injectors and hot gas ducts from a previous NASA-funded program were modified for use to supply the oxidizer-rich combustion products to the oxidizer circuit of the main injector of the thrust chamber. Testing of the resulting integrated test article - which included the preburner, inter-connecting hot gas duct, main injector, and ablative combustion chamber - was conducted at Test Stand 116 at the East Test Area of the NASA MSFC. The test article was well instrumented with static and dynamic pressure, temperature, and vibration sensors. This paper presents and discusses all the hot-fire test results of the integrated test article thrust chamber. Eighteen successful hot-fire tests of the integrated rig were conducted. Testing was accomplished with all five of the injector element concepts. Main combustion chamber pressures ranged from 710 to 2350 psia, and main combustion chamber mixture ratios ranged from 2.47 to 2.87. A chamber barrier fuel film coolant of about 2% to 4% of the total fuel flow was used for most tests. Characteristic exhaust velocity efficiency excluding the influence of the fuel film cooling ranged from 91% to 98% of theoretical. All tests of the thrust chamber exhibited stable combustion, even down to 40% of nominal operating pressures. Compatibility of the injector face and combustion chamber walls was acceptable. This paper is a follow-on to publication of preliminary test data presented at the 2016 JANNAF Liquid Propulsion Subcommittee meeting.
Hulka, J. R.↗
Properties of a Variable-Delay Polarization Modulator
We investigate the polarization modulation properties of a variable-delay polarization modulator (VPM). The VPM modulates polarization via a variable separation between a polarizing grid and a parallel mirror. We find that in the limit where the wavelength is much larger than the diameter of the metal wires that comprise the grid, the phase delay derived from the geometric separation between the mirror and the grid is sufficient to characterize the device. However, outside of this range, additional parameters describing the polarizing grid geometry must be included to fully characterize the modulator response. In this paper, we report test results of a VPM at wavelengths of 350 micron and 3 mm. Electromagnetic simulations of wire grid polarizers were performed and are summarized using a simple circuit model that incorporates the loss and polarization properties of the device.
Chuss, David T.↗
Traveling Wave Tube (TVT) RF Power Combining Demonstration for use in the Jupiter Icy Moons Orbiter (JIMO)
The Jupiter Icy Moons Orbiter (JIMO) is set to launch between the years 2012 and 2015. It will possibly utilize a nuclear reactor power source and ion engines as it travels to the moons of Jupiter. The nuclear reactor will produce hundreds of kilowatts of power for propulsion, communication and various scientific instruments. Hence, the RF amplification devices aboard will be able to operate at a higher power level and data rate. The initial plan for the communications system is for an output of 1000 watts of RF power, a data rate of at least 10 megabits a second, and a frequency of 32 GHz. A higher data rate would be ideal to fully utilize the instruments aboard JIMO. At NASA Glenn, one of our roles in the JIMO project is to demonstrate RF power combining using multiple traveling wave tubes (TWT). In order for the power of separate TWT s to be combined, the RF output waves from each must be in-phase and have the same amplitude. Since different tubes act differently, we had to characterize each tube using a Network Analyzer. We took frequency sweeps and power sweeps to characterize each tube to ensure that they will behave similarly under the same conditions. The 200 watt Dornier tubes had been optimized to run at a lower power level (120 watts) for their extensive use in the ACTS program, so we also had to experiment with adjusting the voltage settings on several internal components (helix, anode, collector) of the tubes to reach the full 200 watt potential. from the ACTS program. Phase shifters and power attenuators were placed in the waveguide circuit at the inputs to the tubes so that adjustments could be made individually to match them exactly. A magic tee was used to route and combine the amplified electromagnetic RF waves on the tube output side. The demonstration of 200 watts of combined power was successful with efficiencies greater than 90% over a 500 MHz bandwidth. The next step will be to demonstrate the use of three amplifiers using two magic tees by adding a 200 watt Dornier tube to the Varian and Logimetrics combined setup for a total of 400 watts. After that we will use two 200 watt Dorniers for 400 watts and eventually four 200 watt Dornier tubes to demonstrate 800 watts. After demonstrating the success of power combining, we will need to verify the integrity of a modulated signal sent through the combined tubes. The purpose will be to see what effects separating and recombining will have on the modulated signal and also what effect it will have on combining efficiency. A Bit Error Rate (BER) will be determined by a Bit Error Rate Tester (BERT) by comparing the random information it transmits to what it receives back. The process began with two 100 watt tubes, a Varian and a Logimetrics, salvaged
Downey, Joseph A.↗
A four-cylinder Stirling engine controls model
A four working space, double acting piston, Stirling engine simulation was developed for controls studies. Two simulations, one for detailed fluid behavior, and a second model with simple fluid behavior but containing the four working space aspects and engine inertias, validate these models separately, then upgrade the four working space model by incorporating the detailed fluid behavior model for all four working spaces. The single working space model contains the detailed fluid dynamics. The four working space (FWS) model was built to observe the behavior of the whole engine. The drive dynamics and vehicle inertia effects are simulated. The capabilities of the model are exercised to look at working fluid supply transients, short circuit transients, and piston ring leakage effects.
Lorenzo, C. F.↗
SOI CMOS Imager with Suppression of Cross-Talk
A monolithic silicon-on-insulator (SOI) complementary metal oxide/semiconductor (CMOS) image-detecting integrated circuit of the active-pixel-sensor type, now undergoing development, is designed to operate at visible and near-infrared wavelengths and to offer a combination of high quantum efficiency and low diffusion and capacitive cross-talk among pixels. The imager is designed to be especially suitable for astronomical and astrophysical applications. The imager design could also readily be adapted to general scientific, biological, medical, and spectroscopic applications. One of the conditions needed to ensure both high quantum efficiency and low diffusion cross-talk is a relatively high reverse bias potential (between about 20 and about 50 V) on the photodiode in each pixel. Heretofore, a major obstacle to realization of this condition in a monolithic integrated circuit has been posed by the fact that the required high reverse bias on the photodiode is incompatible with metal oxide/semiconductor field-effect transistors (MOSFETs) in the CMOS pixel readout circuitry. In the imager now being developed, the SOI structure is utilized to overcome this obstacle: The handle wafer is retained and the photodiode is formed in the handle wafer. The MOSFETs are formed on the SOI layer, which is separated from the handle wafer by a buried oxide layer. The electrical isolation provided by the buried oxide layer makes it possible to bias the MOSFETs at CMOS-compatible potentials (between 0 and 3 V), while biasing the photodiode at the required higher potential, and enables independent optimization of the sensory and readout portions of the imager.
Pain, Bedabrata↗
Hot-Film and Hot-Wire Anemometry for a Boundary Layer Active Flow Control Test
Unsteady active flow control (AFC) has been used experimentally for many years to minimize bluff-body drag. This technology could significantly improve performance of rotorcraft by cleaning up flow separation. It is important, then, that new actuator technologies be studied for application to future vehicles. A boundary layer wind tunnel was constructed with a 1ft-x-3ft test section and unsteady measurement instrumentation to study how AFC manipulates the boundary layer to overcome adverse pressure gradients and flow separation. This unsteady flow control research requires unsteady measurement methods. In order to measure the boundary layer characteristics, both hot-wire and hot-film Constant Temperature Anemometry is used. A hot-wire probe is mounted in the flow to measure velocity while a hot-film array lays on the test surface to measure skin friction. Hot-film sensors are connected to an anemometer, a Wheatstone bridge circuit with an output that corresponds to the dynamic flow response. From this output, the time varying flow field, turbulence, and flow reversal can be characterized. Tuning the anemometers requires a fan test on the hot-film sensors to adjust each output. This is a delicate process as several variables drastically affect the data, including control resistance, signal input, trim, and gain settings.
Control Test↗
Enabling Large Focal Plane Arrays through Mosaic Hybridization
We have demonstrated the hybridization of large mosaics of far-infrared detectors, joining separately fabricated sub-units into a single unit on a single, large substrate. We produced a single detector mockup on a 100mm diameter wafer and four mockup readout quadrant chips from a separate 100mm wafer. The individually fabricated parts were hybridized using a Suss FC150 flip chip bonder to assemble the detector-readout stack. Once all of the hybridized readouts were in place, a single, large and thick silicon substrate was placed on the stack and attached with permanent epoxy to provide strength and a Coefficient of Thermal Expansion (CTE) match to the silicon components underneath. Wirebond pads on the readout chips connect circuits to warm readout electronics; and were used to validate the successful superconducting electrical interconnection of the mockup mosaic-hybridized detector. This demonstration is directly scalable to 150 mm diameter wafers, enabling pixel areas over ten times the area currently demonstrated.
Miller, Timothy M.↗
Monolithic 20-GHz Transmitting Module
20-GHz monolithic microwave/millimeter-wave integrated circuit (MMIC) with amplification and phase-shift (time-delay) capabilities developed. Use of MMIC module technology promises to make feasible development of weight- and cost-effective phased-array antenna systems, identified as major factor in achieving minimum cost and efficient use of frequency and orbital resources of future generations of communication satellite systems. Use of MMIC transmitting modules provides for relatively simple method for phase-shift control of many separate radio-frequency (RF) signals required for phased-array antenna systems.
Kascak, T.↗
Inversion layer solar cell fabrication and evaluation
Inversion layer solar cells were fabricated by etching through the diffused layer on p-type silicon wafers in a comb-like contact pattern. The charge separation comes from an induced p-n junction at the surface. The inverted surface is caused by a layer of transparent material applied to the surface that either contains free positive ions or that creates donor states at the interface. Cells are increased from 3 ma I sub sc to 100 ma by application of sodium silicate. The action is unstable, however, and decays. Non-mesa contaminated oxide cells were fabricated with short circuit currents of over 100 ma measured in the sun. Cells of this type have demonstrated stability.
Call, R. L.↗
NASA Tech Briefs, November 2006
Topics include: Simulator for Testing Spacecraft Separation Devices; Apparatus for Hot Impact Testing of Material Specimens; Instrument for Aircraft-Icing and Cloud-Physics Measurements; Advances in Measurement of Skin Friction in Airflow; Improved Apparatus for Testing Monoball Bearings; High-Speed Laser Scanner Maps a Surface in Three Dimensions; Electro-Optical Imaging Fourier-Transform Spectrometer; Infrared Instrument for Detecting Hydrogen Fires; Modified Coaxial Probe Feeds for Layered Antennas; Detecting Negative Obstacles by Use of Radar; Cryogenic Pound Circuits for Cryogenic Sapphire Oscillators; PixelLearn; New Software for Predicting Charging of Spacecraft; Conversion Between Osculating and Mean Orbital Elements; Generating a 2D Representation of a Complex Data Structure; Making Activated Carbon by Wet Pressurized Pyrolysis; Composite Solid Electrolyte Containing Li+- Conducting Fibers; Electrically Conductive Anodized Aluminum Surfaces; Rapid-Chill Cryogenic Coaxial Direct-Acting Solenoid Valve; Variable-Tension-Cord Suspension/Vibration- Isolation System; Techniques for Connecting Superconducting Thin Films; Versatile Friction Stir Welding/Friction Plug Welding System; Thermal Spore Exposure Vessels; Enumerating Spore-Forming Bacteria Airborne with Particles; Miniature Oxidizer Ionizer for a Fuel Cell; Miniature Ion-Array Spectrometer; Promoted-Combustion Chamber with Induction Heating Coil; Miniature Ion-Mobility Spectrometer; Mixed-Salt/Ester Electrolytes for Low-Temperature Li+ Cells; Miniature Free-Space Electrostatic Ion Thrusters; Miniature Bipolar Electrostatic Ion Thruster; Holographic Plossl Retroreflectors; Miniature Electrostatic Ion Thruster With Magnet; Using Apex To Construct CPM-GOMS Models; Sequence Detection for PPM Optical Communication With ISI; Algorithm for Rapid Searching Among Star-Catalog Entries; Expectation-Based Control of Noise and Chaos; Radio Heating of Lunar Soil to Release Gases; Using Electrostriction to Manipulate Ullage in Microgravity; Equations for Scoring Rules When Data Are Missing; Insulating Material for Next-Generation Spacecraft; and Pseudorandom Switching for Adding Radar to the AFF Sensor.
Source record↗