Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Selective wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Augmented Monitoring and Condition Assessment Program (AMCAP) Material Test Reactor (MTR) (Fuel Inspection Program Report)

The AMCAP MTR Fuel Inspection Program, a special inspection program comprised of four inspection campaigns, examined a total of ten (10) pre-selected aluminum-clad, aluminum-based fuel core spent nuclear fuel assemblies (ASNF) stored in the L Area Disassembly Basin (L Basin) at the Savannah River Site. A full description of the inspections and the results are reported. The fuel had been stored in bundled-tube storage (Vertical Tube Storage) for periods of 18 to 21 years. The prior service experience of the individual 10 assemblies varies, but all included irradiation followed by wet storage at international research reactor sites prior to shipment to the US and storage in L Basin. The 10 assemblies were expected to be among the “worst"’ in terms of prior corrosion damage of the entire inventory of the direct-bundle-stored ASNF in L Basin. The inventory of MTR ASNF in L Basin will continue to be stored in the bundled-tube configuration or in slug-storage buckets with inserts pending retrieval for ultimate disposition. The MTR fuel inspections focused on collecting information for characterization of the material condition of the ASNF considering various types of aluminum fuel corrosion degradation of its assembled materials in water storage. A custom-designed Fuel Inspection Table was used to stage the fuel for remote, enhanced visual examination (close-up video imaging & recording) with controlled lighting and positioning that enables reproducibility of imaging conditions. The inspections were conducted by fuel subject matter expert staff from Spent Fuel Project Engineering (SFPE) and the Savannah River National Laboratory (SRNL). Stills captured from the video records were used to compare the corrosion evolution from previous records, as available. This evaluation of the inspection results including the comparison to the previous inspection results demonstrate that the water quality and the storage configuration of ASNF in L Basin do not cause aggressive corrosion degradation of the fuel; mitigation of the prior corrosion degradation of the fuel also appears to have been achieved with the good water quality conditions of L Basin. Recommendations are made for future inspection of the fuel to trend corrosion degradation and demonstrate continued safe wet storage of the ASNF in L Basin. The next fuel examination is recommended to be performed in 5 years.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Seasonal investigation of ultrafine-particle organic composition in an eastern Amazonian rainforest

Abstract. Reports on the composition of ultrafine particles (<100 nm in diameter) in the Amazon are scarce, due in part to the fact that new-particle formation has rarely been observed near ground level. Ultrafine particles near the surface have nevertheless been observed, leaving open questions regarding the sources and chemistry of their formation and growth, particularly as these vary across seasons. Here, we present measurements of the composition of ultrafine particles collected in the Tapajós National Forest (2.857° S, 54.959° W) during three different seasonal periods: 10–30 September 2016 (SEP), 18 November–23 December 2016 (DEC), and 22 May–21 June 2017 (JUN). Size-selected (5–70 nm) particles were collected daily (for 22 h each day) using an offline sampler. Samples collected during the three time periods were compiled and analyzed using liquid chromatography coupled with Orbitrap high-resolution mass spectrometry. Our findings suggest a sustained influence of isoprene organosulfate chemistry on ultrafine particles from the different periods. We present chemical evidence that indicates that biological-spore fragmentation impacted ultrafine-particle composition during the late wet season (JUN), while chemical markers for biomass burning and secondary chemistry peaked during the dry season (SEP and DEC). Higher oxidation states and degrees of unsaturation were observed for organics in the dry season (SEP and DEC), suggesting greater extents of aerosol aging. Finally, applying a volatility parameterization to the observed compounds suggests that organic sulfur species are likely key drivers of new-particle growth in the region due to their low volatility compared to other species.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Tuning transport in graphene oxide membrane with single-site copper ($\mathrm{II}$) cations

Controlling the ion transport through graphene oxide (GO) membrane is challenging, particularly in the aqueous environment due to its strong swelling tendency. Fine-tuning the interlayer spacing and chemistry is critical to create highly selective membranes. We investigate the effect of single-site divalent cations in tuning GO membrane properties. Competitive ionic permeation test indicates that Cu 2+ cations dominate the transport through the 2D channels of GO membrane over other cations (Mg 2+ /Ca 2+ /Co 2+ ). Without/With the single-site M 2+ modifications, pristine GO, Mg-GO, Ca-GO, and Cu-GO membranes show interlayer spacings of ~13.6, 15.6, 14.5, and 12.3 Å in wet state, respectively. The Cu-GO membrane shows a two-fold decrease of NaCl (1 M) permeation rate comparing to pristine GO, Mg-GO, and Ca-GO membranes. In reverse osmosis tests using 1000 ppm NaCl and Na 2 SO 4 as feeds, Cu-GO membrane shows rejection of ~78% and ~94%, respectively, which are 5%–10% higher than its counterpart membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Soil Metabolomics Predict Microbial Taxa as Biomarkers of Moisture Status in Soils from a Tidal Wetland

We present observations from a laboratory-controlled study on the impacts of extreme wetting and drying on a wetland soil microbiome. Our approach was to experimentally challenge the soil microbiome to understand impacts on anaerobic carbon cycling processes as the system transitions from dryness to saturation and vice-versa. Specifically, we tested for impacts on stress responses related to shifts from wet to drought conditions. We used a combination of high-resolution data for small organic chemical compounds (metabolites) and biological (community structure based on 16S rRNA gene sequencing) features. Using a robust correlation-independent data approach, we further tested the predictive power of soil metabolites for the presence or absence of taxa. Here, we demonstrate that taking an untargeted, multidimensional data approach to the interpretation of metabolomics has the potential to indicate the causative pathways selecting for the observed bacterial community structure in soils.

16S rRNA gene↗
DOE OSTI2026

Impact of Rock Wettability and Mineralization on CO 2 Storage Efficiency in Basalt Reservoirs

Basalt formations have emerged as highly promising targets for geological CO 2 storage due to their abundance of reactive silicate minerals that can rapidly convert dissolved CO 2 into stable carbonate minerals. The efficiency of CO 2 trapping in basalts, however, depends not only on their geochemical reactivity but also on reservoir wettability, which governs how CO 2 partitions among structural, residual, solubility, and mineral trapping mechanisms. However, wettability and mineral kinetics have largely been examined separately, wettability for plume migration and kinetics in terms of mineralization, leaving their coupled impact unquantified. Here, we systematically integrate th ese processes in a reservoir-scale reactive transport model to quantify the impact of three distinct wettability conditions (water-wet, mixed-wet, and CO 2 -wet) on plume migration, mineral precipitation, pore-scale blockage, and long-term immobilization. Results show that under ideal conditions (no mineralization), water-wet systems exhibited plume aspect ratios up to 28% higher than CO 2 -wet systems and promoted at least 60% greater residual trapping. When mineralization was incorporated, mineral trapping accounted for 57%, 53%, and 46% of the total immobilized CO 2 in water-wet, mixed-wet, and CO 2 -wet systems, respectively. Dissolved CO 2 contributed 43-46%, while residual trapping remained below 5%, and mobile CO 2 was substantially reduced due to mineralization, demonstrating that as the system becomes more water-wet, CO 2 is more effectively converted into stable carbonate minerals, although extensive mineral precipitation may lead to pore clogging. A global Sobol-Morris sensitivity analysis further reveals that the kinetic parameters of reactive minerals are the most influential factor, followed by wettability, while salinity has only a minor influence. Furthermore, these findings highlight that wettability is not merely a flow property but a fundamental control on CO 2 mineralization in basalts, with direct implications for site selection for storage projects.

Basalts↗
NASA NTRS1978

Guidelines for the selection and application of tantalum electrolytic capacitors in highly reliable equipment

Guidelines are given for the selection and application of three types of tantalum electrolytic capacitors in current use in the design of electrical and electronic circuits for space flight missions. In addition, the guidelines supplement requirements of existing military specifications used in the procurement of capacitors. A need exists for these guidelines to assist designers in preventing some of the recurring, serious problems experienced with tantalum electrolytic capacitors in the recent past. The three types of capacitors covered by these guidelines are; solid, wet foil, and tantalum cased wet slug.

Holladay, A. M.↗
DOE OSTI2021

Structure-Activity Relationships of Hydrothermally Aged Titania-Supported Vanadium-Tungsten Oxide Catalysts for SCR of NOx Emissions with NH3

Supported V2O5-WO3/TiO2 materials employed as selective catalytic reduction (SCR) catalysts for NOx emission control from power plants. Fresh SCR catalysts usually receive exposure to harsh treatments in industry to accelerate catalyst activation (calcination in air at 650oC) and catalyst aging (hydrothermal aging at 650oC) in a way that represents various points in the catalyst/product lifetime. The present study investigates the catalyst structural and chemical changes occurring during such harsh treatments. Three series of supported V2O5-WO3/TiO2 catalysts were prepared by incipient-wetness impregnation of aqueous ammonium metavanadate and metatungstate precursors. The catalysts were subsequently dried and calcined at 550oC in O2, 650oC in O2, and hydrothermal conditions (10% O2, 8% H2O, 7% CO2 and 75% N2) at 650oC. The resulting catalysts were physically characterized by numerous techniques (in situ Raman, in situ IR, in situ High Field-High Spinning solid-state 51V MAS NMR, in situ EPR, XRD, BET surface area and ICP) and chemically probed with adsorbed ammonia, SCR-TPSR, and the SCR reaction. The surface WOx sites on the TiO2 support behave as a textural promoter that stabilizes the TiO2 (anatase) phase from sintering and transforming to the undesirable crystalline TiO2 (rutile) phase that can lead to formation of a Ti1-xVxO2 (rutile) solid solution with reduced V4+ cations (~7-15%). The surface VOx sites are mostly oligomerized as surface V+5Ox sites (~50-85% oligomers) and the extent of oligomerization tends to increase with surface WOx coverage and calcination temperature. A major difference between the calcined and hydrothermally treated catalysts was the low concentration of surface NH3* species on Lewis acid sites for the hydrothermally treated catalysts, yet the SCR activity was almost comparable for both catalysts. This finding suggests that surface NH4+*, primarily associated with the surface VOx sites, are able to efficiently perform the SCR reaction. Given that multiple catalyst parameters were simultaneously varying during these treatments, it was difficult to correlate the SCR activity with any single catalyst parameter. A correlation, however, was found between the SCR TOF/activity and the sum of the surface NH3* and NH4+* species, which is dominated by the surface NH4+* species.

SCR, NO, NH3, catalyst, V2O5, WO3, TiO2, promotion↗
DOE OSTI2020

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO 2 Foam Transport in Fractured Unconventional Reservoirs

Pressure limitations of many microfluidic platforms have been a significant challenge in microfluidic experimental studies of fractured media. As a result, these platforms have not been fully exploited for direct observation of high-pressure transport in fractures. This work introduces microfluidic platforms that enable direct observation of multiphase flow in devices featuring surrogate permeable media and fractured systems. Such platforms provide a pathway to address important and timely questions such as those related to CO 2 capture, utilization and storage. This work provides a detailed description of the fabrication techniques and an experimental setup that may serve to analyze the behavior of supercritical CO 2 (scCO 2 ) foam, its structure and stability. Such studies provide important insights regarding enhanced oil recovery processes and the role of hydraulic fractures in resource recovery from unconventional reservoirs. This work presents a comparative study of microfluidic devices developed using two different techniques: photolithography/wet-etching/ thermal-bonding versus Selective Laser-induced Etching. Both techniques result in devices that are chemically and physically resistant and tolerant of high pressure and temperature conditions that correspond to subsurface systems of interest. Both techniques provide pathways to high-precision etched microchannels and capable lab-on-chip devices. Photolithography/wet-etching, however, enables fabrication of complex channel networks with complex geometries, which would be a challenging task for laser etching techniques. This work summarizes a step-by-step photolithography, wet-etching and glass thermal-bonding protocol and, presents representative observations of foam transport with relevance to oil recovery from unconventional tight and shale formations. In conclusion, this work describes the use of a high resolution monochromatic sensor to observe scCO 2 foam behavior where the entirety of the permeable medium is observed simultaneously while preserving the resolution needed to resolve features as small as 10 μm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1986

Adsorption and condensation of amino acids and nucleotides with soluble mineral salts

The directed synthesis of biopolymers in an abiotic environment is presumably a cyclic sequence of steps which may be realized in a fluctuating environment such as a prebiotic pond undergoing wetting-drying cycles. Soluble mineral salts have been proposed as an essential component of this fluctuating environment. The following sequence may be considered as a most primitive mechanism of information transfer in a fluctuating environment: (1) adsorption of a biomolecule onto a soluable mineral salt surface to act as an adsorbed template; (2) specific adsorption of biomonomers onto the adsorbed template; (3) condensation of the adsorbed biomonomers; and (4) desorption of the elongated oligomer. In this investigation, the salts selected for study were CaSO4.2H2O(gypsum), SrSO4, and several other metal sulfates and chlorides. Adsorption of the monomeric species, gly, 5'AMP 5'GMP, and 5'CMP was investigated. The adsorbed template biopolymers used were Poly-A, Poly-G, Poly-C, and Poly-U. The results of studies involving these experimental participants, the first two steps of the proposed primitive information transfer mechanism, and condensation of amino acids to form oligomers in a fluctuating environment are to be reported.

Orenberg, J.↗
DOE OSTI2022

Restored Passivation after Complete Removal of Front Poly-Si Between the Grid in Poly-Si/SiO2 Front/Back Cells

This work explores the use of wet chemical etching to completely remove the front poly-Si layer between grid lines of a front/back poly-Si/SiO2 passivated contact device. The purpose of the work is to provide excellent passivation under the metal grid, but to also maximize Jsc by eliminating optical absorption in the front poly-Si. We show that after a high temperature anneal to distribute carriers in the poly-Si/SiO2/c-Si interface all of the poly-Si can be removed selectively with TMAH, using the SiO2 as an etch-stop layer. The etched surface can be repassivated back to its original level with the addition of a SiNx/Al2O3 stack grown on the preserved tunnelling oxide layer followed by a short forming gas anneal. Using symmetric 100 - 200 nm intrinsically doped poly-Si/SiO2 on textured n-type wafer templates we show absolute device efficiency enhancement from 15% to 21% by increasing the Jsc by 12 mA/cm2 after removing the front poly-Si and repassivating while effectively preserving the Voc, and FF of the device. IQE values are similar to PERC devices in the short wavelength range.

etching↗
DOE OSTI2021

Comparative analysis of various pretreatments to mitigate fouling and scaling in membrane distillation

Membrane distillation (MD) has shown strong promise for treating hypersaline produced water (PW) streams. Scaling and fouling on the membrane surface, however, have been identified as major challenges for commercialization and widespread application. The focus of this study was to first identify the nature of foulants and scalants on the membrane surface and then investigate the pretreatment strategies that mitigate the extent of fouling and scaling on the membrane surface. Vacuum MD (VMD) was selected for this study because of its higher flux at more moderate feed temperatures that eventually leads better assessment of fouling and scaling on the membrane surface. VMD flux tests were carried out with three different real PW samples at total dissolved solids concentrations in the range of 120-160 g/L. It was found that an efficient pretreatment prior to MD is required to mitigate the fouling potential of the organic matter, mostly suspended constituents, in PW samples. Suspended organics fouled and quickly wetted the MD membrane. Major conventional treatments, including filtration, oxidation, coagulation, air floatation, and aeration were investigated to pretreat the PW before VMD tests. A comprehensive comparative analysis is presented showing that the ultrafiltration and coagulation pretreatments displayed the best performance in mitigating the fouling and scaling, while oxidative pretreatment was found to be effective in reducing the iron concentration to less than 5 ppm. The surface of scaled membranes was carefully characterized to further evaluate the performance of each pretreatment. The components that had the highest tendency to precipitate on the membrane surface were identified as strontium sulfate, calcium carbonate, sodium chloride, iron oxide, and silica. In closing, these findings are supported by thermodynamic estimation of the saturation index.

42 ENGINEERING↗
DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Augmented Monitoring and Condition Assessment Program for SNF Wet Storage Life Extension - 20489

Approximately 27 MTHM of spent nuclear fuel (SNF) owned and managed by the U.S. Department of Energy, Office of Environmental Management is stored in the L Basin at the Savannah River Site (SRS). This 'DOE SNF' is comprised of approximately 12,000 aluminum-clad, aluminum-based fuel assemblies (∼7 MTHM), and approximately 2000 non-aluminum fuel assemblies (∼20 MTHM). A program is in progress to perform Non-Destructive Examination (NDE) of the fuel and their storage containers to characterize the materials' condition, and to evaluate the effects of service to enable continued safe wet storage of the SNF. The Augmented Monitoring and Condition Assessment Program (AMCAP), a two-part program to develop and implement remote underwater Non-Destructive Examination of the aluminum SNF, and of the containers of the non-aluminum SNF, respectively, is aimed at the characterization and evaluation of corrosion degradation of aluminum fuel and container materials. The predominant design of the aluminum SNF (ASNF) stored in L Basin is the Materials Test Reactor (MTR) equivalent design, a plate fuel design. These SNF are stored in 5'' diameter tubes or 5'' x 5'' squares (called bundles) that are nominally 12' or up to 14' long. The SNF is de-bundled and inspected using a custom-designed MTR Fuel Inspection Table. The inspection table provides for indexed fuel positioning for a video camera examination with controlled lighting. A total of 10 of the SNF originating from foreign research and test reactors were selected for examination based on burnup, enrichment, and prior damage caused by service/storage history. A special inspection campaign of these 10 assemblies is in progress. The observed corrosion damage included minor to moderate attack from general corrosion, pitting, crevice, end grain and galvanic corrosion. Example results from the completed inspections are shown and discussed. The focus is a comparison of the as-received condition versus the as-found current storage condition that will serve to validate Water Chemistry and Corrosion Monitoring Programs. The non-aluminum SNF (NASNF) stored in L Basin are of diverse design that includes various geometries with claddings of stainless steel, Zircaloy, and Hastelloy. The fuel core materials include uranium alloys, oxides/mixed oxides, and carbides. These SNF materials, originating from early experimental and test reactors, are in various physical forms including single fuel elements and cut pieces. The fuel is stored in L Basin in various configurations including in direct bundled storage in aluminum tubes and in isolation cans that are in the bundles or in a larger over-size storage container (OSC). Concern with inside-out corrosion and the potential loss of configuration control and ability to handle the storage containers prompted the development of remote NDE methods that include visual and UT technologies to assess the condition of the containers. Candidate stored materials were selected for a special inspection campaign; the development of the NDE methods for the inspection for galvanic, crevice and sediment-induced corrosion (inside-out) are discussed. A summary of the SNF storage in L Basin at the SRS, and an overview of the AMCAP to enable continued safe storage of DOE SNF are described. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Hierarchical Galloaluminosilicate MFI Catalysts for Ethane Nonoxidative Dehydroaromatization

This study presented an approach to overcome diffusion limitation and imbalance between Brønsted and Lewis acidities that affect conversion and aromatic yield in alkane nonoxidative dehydroaromatization (DHA) conversion. Three different Ga-promoted ZSM-5 catalysts were synthesized for the ethane DHA reaction. The hierarchical galloaluminosilicate Meso-GaZSM-5 was prepared by the solid-state crystallization technique wherein Ga was introduced through the in situ synthesis process. The microporous galloaluminosilicate Micro-GaZSM-5 was synthesized by the hydrothermal technique wherein Ga was introduced in situ during zeolite formation. The hierarchically structured Ga-Meso-ZSM-5 was synthesized by the solid-state crystallization method, but the Ga was introduced by the incipient wetness method. Additional Pt was incorporated by the incipient wetness technique for all three catalysts to enhance the DHA activity. The solid-state crystallization technique created the hierarchical structure without using a template. With the in situ technique, Ga species replaced the Al framework, reducing the strong Brønsted acidity. Meanwhile, they created the extraframework GaO + , introducing the strong Lewis acid sites into catalysts. Due to better synergistic interaction between the oxidation state of metals, acidic properties, and catalyst porosity, Pt-Meso-GaZSM-5 showed higher C 2 H 6 conversion and aromatic selectivity. The improvement on diffusivity not only reduces the effect of channel blockage but also improves the utilization of active sites. As a result, this work sheds light on the direct, nonoxidative conversion of shale gas without going through the syngas route.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Defect suppression in wet-treated etched-and-regrown nonpolar m-plane GaN vertical Schottky diodes: A deep-level optical spectroscopy analysis

In this work, steady-state photocapacitance (SSPC) was conducted on nonpolar m-plane GaN n-type Schottky diodes to evaluate the defects induced by inductively coupled plasma (ICP) dry etching in etched-and-regrown unipolar structures. An ~10× increase in the near-midgap Ec – 1.9 eV level compared to an as-grown material was observed. Defect levels associated with regrowth without an etch were also investigated. The defects in the regrown structure (without an etch) are highly spatially localized to the regrowth interface. Subsequently, by depth profiling an etched-and-regrown sample, we show that the intensities of the defect-related SSPC features associated with dry etching depend strongly on the depth away from the regrowth interface, which is also reported previously. A photoelectrochemical etching (PEC) method and a wet AZ400K treatment are also introduced to reduce the etch-induced deep levels. A significant reduction in the density of deep levels is observed in the sample that was treated with PEC etching after dry etching and prior to regrowth. An ~2× reduction in the density of Ec – 1.9 eV level compared to a reference etched-and-regrown structure was observed upon the application of PEC etching treatment prior to the regrowth. The PEC etching method is promising for reducing defects in selective-area doping for vertical power switching structures with complex geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Assessment of CMIP5 and CMIP6 AMIP Simulated Clouds and Surface Shortwave Radiation Using ARM Observations over Different Climate Regions

The simulations of clouds and surface radiation from 10 CMIP6 models and their CMIP5 predecessors are compared to the ARM ground-based observations over different climate regions. Compared to the ARM radar-lidar derived total cloud fractions (CFT) and cloud fraction vertical distributions over the six selected sites, both CMIP5 and CMIP6 significantly underestimated CFT and low-level CF over the Northern Hemispheric midlatitude sites (SGPC1 and ENAC1), although the biases are generally smaller in CMIP6. Over the tropical oceanic site (TWPC2), 5 out of 10 CMIP6 models better simulated low-level CF than their CMIP5 predecessors. CMIP6 simulations generally agreed well with the ARM observations in CFT and cloud fraction vertical distributions over the tropical continental (MAOM1) and coastal (TWPC3) sites but missed the transitions between dry and wet seasons, similar to CMIP5 simulations. The improvements in downwelling shortwave fluxes (SWdn) at the surface from the majority of CMIP6 compared to CMIP5 primarily resulted from the improved cloud fraction simulations, especially over the SGPC1, ENAC1, and TWPC3 sites. By contrast, both CMIP5 and CMIP6 models exhibited diverse performances of clouds and shortwave radiation over the Arctic site (NSAC1), where CMIP6 models produced more clouds than CMIP5 models, especially for the low-level clouds. The comparisons between observations and CMIP5 and CMIP6 simulations provide valuable quantitative assessments of the accuracy of mean states and variabilities in the model simulations and shed light on general directions to improve climate models in different regions.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1993

Investigation of etching techniques for superconductive Nb/Al-Al2O3/Nb fabrication processes

Wet etching, CF4 and SF6 reactive ion etching (RIE), RIE/wet hybrid etching, Cl-based RIE, ion milling, and liftoff techniques have been investigated for use in superconductive Nb/Al-Al2O3/Nb fabrication processes. High-quality superconductor-insulator-superconductor (SIS) junctions have been fabricated using a variety of these etching methods; however, each technique offers distinct tradeoffs for a given process an wafer design. In particular, it was shown that SF6 provides an excellent RIE chemistry for low-voltage anisotropic etching of Nb with high selectivity to Al. The SF6 tool has greatly improved the trilevel resist junction insulation process. Excellent repeatability, selectivity with respect to quartz, and submicron resolution make Cl2 + BCl3 + CHCl3 RIE a very attractive process for trilayer patterning.

Lichtenberger, A. W.↗
NASA NTRS2005

Protonic Conduction of BaCe0.85YO. 1503 Doped with SrTiO3

Reformers based on ceramic membrane technology potentially offer hydrogen production that is comparable to the cost of fossil fuels. Protonic conducting ceramic with the chemical formula AB03 offers the promise of highly selective hydrogen separation at intermediate temperature (400-800 C). Among different perovskite-type oxides, BaCe03 and SrCe03 based compositions show high protonic conductivities but strong resistance to densification. X-ray diffraction studies on sintered specimens of BaCe0.85Y0.1503-6 show multi-phase formation which was found to show dependence upon powder synthesis method. Doping with SrTiO3 suppresses multi-phase formation and enhances grain growth. Conductivity measurements in temperature range of 200 to 1000 C were performed by ac impedance spectroscopy under dry and wet conditions. Sintering behavior, phase formation and conductivity results will be reported.

Dynys, Frederick W.↗