SEARCH · Engineering Papers

Results for “STRAINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Strain-tunable microwave-resonance technique for quantum materials

By integrating a dielectric microwave resonator with a piezoelectric-based strain device, we develop an in situ strain-tunable microwave spectroscopy technique that enables contactless measurements of material properties under strain. To demonstrate the capability of this device, we measure the strain-dependent microwave surface impedance of the representative iron-based superconductor Ba⁢Fe 2 (As 1−𝑥 ⁢P 𝑥 ) 2 at the slightly overdoped composition. We successfully control and observe the suppression of superconductivity under both compressive and tensile anisotropic lattice distortions along the tetragonal [110] T direction, as manifested by changes in the quality factor and resonance frequency shifts of microwave resonance. Furthermore, strain-induced changes in microwave surface resistivity, an extension of conventional DC-limit transport elastoresistivity to the microwave regime, provide information on electronic anisotropy equivalent to that of DC elastoresistivity, while offering a contactless alternative. Furthermore, our strain-tunable cavity therefore serves as a powerful, contactless probe of fundamental material properties under strain and may also potentially facilitate the design of hybrid quantum systems with strain-engineered quantum degrees of freedom.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Upgraded fiber-optic sensor system for dynamic strain measurement in Spallation Neutron Source

We describe an upgraded fiber-optic sensor system and its performance in measuring the dynamic strains in a mercury target of the Spallation Neutron Source (SNS). Strains result from dynamic pressure waves in the stainless-steel mercury target induced by short (~700 ns), intense (up to 23.3 kJ), high-energy (~1 GeV) proton pulses. In the upgraded sensor system, the output of each sensor head is interrogated with a compact, all-fiber based Faraday Michelson interferometer, which generates interference signals with a steady phase shift. Strain waveforms are recovered from the phase-shifted interference signals using a high-speed digital signal processing procedure developed in our previous work. We demonstrate successful measurements of dynamic strain pulses, e.g., 400με over 190μs , on a recently installed SNS target using the upgraded sensor system. The measured strain waveforms are analyzed for more than 20 sensor locations and/or orientations, and provide information regarding the temporal structure of strain profiles and dependence of the strain magnitude on the proton powers of 200 – 1400 kW. The new interrogator also measures the radiation-induced-attenuation (RIA) in the optical fiber, enabling experimental investigations of RIA profiles induced by a 700-ns radiation pulse. The radiation effects on the strain measurement performance are discussed over a radiation dose range of up to 4×10 8 Gy and an RIA compensation method is proposed. The measurements allow insight into the response of this unique piece of equipment and can be used for validation of simulations.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

divergence in basal transcriptomes of "Wild Type" Chlamydomonas reinhardtii strains

This is a study to compare the basal transcriptomes of several widely used laboratory strains of the Chlorophyte alga, Chlamydomonas reinhardtii. Given that there is a high degree of genetic diversity among the closely-related laboratory strains, we wished to examine how much variation there is at the transcriptome level. A panel of WT strains (CC-124, CC-125, CC-1009, CC-1690, CC-1691), all believed to be descended from a single zygospore isolated in 1945, were chosen based on their representing the oldest lineages among the standard laboratory strains. Additionally, CC-4532, which was the source for the current (v6) reference assembly, and CC-4533, which is the initial parental strain of the CLiP library collection of mutant strains, were also included in this study based on their significance to the Chlamydomonas community. All strains were grown in liquid cultures under identical, mixotrophic conditions (light + acetate) to mid-log phase before collecting mRNA for RNA-Seq analysis. Overall design: Pre-cultures of each strain (CC-124, CC-125, CC-1009, CC-1690, CC-1691, CC-4532, and CC-4533) were used to innoculate flasks of Tris-Acetate-Phosphate (TAP) media supplemented with Kropat's trace metals at a concentration of 1.5 x 10^4 cells/mL. Flasks were placed on a shaking platform at 180 RPM under 50-70 µmol x m^-2 x s^-1 of light. Cultures were grown until they reached ~2-3 x 10^6 cells/mL, about three days, before total RNA was collected and subjected RNA-Seq analysis.

Source record↗

DOE OSTI2023

Genetic variation and genetic complexity of nodule occupancy in soybean inoculated with USDA110 and USDA123 rhizobium strains

Abstract Background Symbiotic nitrogen fixation differs among Bradyrhizobium japonicum strains. Soybean inoculated with USDA123 has a lower yield than strains known to have high nitrogen fixation efficiency, such as USDA110. In the main soybean-producing area in the Midwest of the United States, USDA123 has a high nodule incidence in field-grown soybean and is competitive but inefficient in nitrogen fixation. In this study, a high-throughput system was developed to characterize nodule number among 1,321 Glycine max and 69 Glycine soja accessions single inoculated with USDA110 and USDA123. Results Seventy-three G. max accessions with significantly different nodule number of USDA110 and USDA123 were identified. After double inoculating 35 of the 73 accessions, it was observed that PI189939, PI317335, PI324187B, PI548461, PI562373, and PI628961 were occupied by USDA110 and double-strain nodules but not by USDA123 nodules alone. PI567624 was only occupied by USDA110 nodules, and PI507429 restricted all strains. Analysis showed that 35 loci were associated with nodule number in G. max when inoculated with strain USDA110 and 35 loci with USDA123. Twenty-three loci were identified in G. soja when inoculated with strain USDA110 and 34 with USDA123. Only four loci were common across two treatments, and each locus could only explain 0.8 to 1.5% of phenotypic variation. Conclusions High-throughput phenotyping systems to characterize nodule number and occupancy were developed, and soybean germplasm restricting rhizobium strain USDA123 but preferring USDA110 was identified. The larger number of minor effects and a small few common loci controlling the nodule number indicated trait genetic complexity and strain-dependent nodulation restriction. The information from the present study will add to the development of cultivars that limit USDA123, thereby increasing nitrogen fixation efficiency and productivity.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Novel reusable animal model for comparative evaluation of in vivo growth and protein-expression of Escherichia coli O157 strains in the bovine rumen

Previously, we had demonstrated that Escherichia coli O157:H7 (O157) strain 86–24 expresses proteins involved in survival rather than virulence in vitro in rumen fluid from dairy cattle limit fed a maintenance diet. Here, we verified if this observation would be true for different O157 strains grown in vitro in rumen fluid from, and in vivo in the rumen of, animals on contrasting maintenance (high fiber) and lactation (high energy-protein) diets usually limit fed to dairy cattle. For the in vivo studies, an economical, novel, reusable and non-terminal rumen-fistulated animal model permitting simultaneous evaluation of multiple bacterial strains in the bovine rumen was developed. All experiments were conducted in duplicate using different animals to account for host-related variations. The O157 strains included, 86–24, EDL933 and the super shed SS-17. E. coli Nal R (#5735), derived from a bovine intestinal commensal E. coli, was included as a control. As expected, diet influenced ruminal pH and volatile fatty acid (VFA) composition. The pH ranged from 6.2–7.0 and total VFA concentrations from 109–141 μM/ml, in animals fed the maintenance diet. In comparison, animals fed the lactation diet had a ruminal pH ranging between 5.18–6.0, and total VFA of 125–219 μM/ml. Strain dependent differences in O157 recovery from the rumen fluid of cattle fed either diet was observed, both in vitro and in vivo, with O157 strains 86–24 and EDL933 demonstrating similar survival patterns. Analysis of the O157 proteomes expressed in the rumen fluid/rumen verified previous observations of adaptive responses. Any difference in the adaptive response was mainly influenced by the animal’s diet and growth conditions (in vitro and in vivo) and not the O157 strain. These new insights into the O157 responses could help formulate modalities to control O157 across strains in cattle at all stages of husbandry.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2024

Shubnikov-de Haas oscillations of biaxial-strain-tuned superconductors in pulsed magnetic field up to 60 T

Two-dimensional (2D) materials have gained increasing prominence not only in fundamental research but also in daily applications. However, to fully harness their potential, it is crucial to optimize their properties with an external parameter and track the electronic structure simultaneously. Magnetotransport over a wide magnetic field range is a powerful method to probe the electronic structure and, for metallic 2D materials, quantum oscillations superimposed on the transport signals encode Fermi surface parameters. In this manuscript, we utilize biaxial strain as an external tuning parameter and investigate the effects of strain on the electronic properties of two quasi-2D superconductors, MoTe 2 and RbV 3 Sb 5 , by measuring their magnetoresistance in pulsed magnetic fields up to 60 T. With a careful selection of insulating substrates, we demonstrate the possibility of both the compressive and tensile biaxial strains imposed on MoTe 2 and RbV 3 Sb 5 , respectively. For both systems, the applied strain has led to superconducting critical temperature enhancement compared to their free-standing counterparts, proving the effectiveness of this biaxial strain method at cryogenic temperatures. Clear quantum oscillations in the magnetoresistance—the Shubnikov–de Haas (SdH) effect—are obtained in both samples. In strained MoTe 2 , the magnetoresistance exhibits a nearly quadratic dependence on the magnetic field and remains non-saturating even at the highest field, whereas in strained RbV 3 Sb 5 , two SdH frequencies showed a substantial enhancement in effective mass values, hinting at a possible enhancement of charge fluctuations. Our results demonstrate that combining biaxial strain and pulsed magnetic field paves the way for studying 2D materials under unprecedented conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Complete genome sequence of Sphingobium yanoikuyae strain CC4533

We have isolated a new strain of Sphingobium yanoikuyae , which belongs to the class Alphaproteobacteria, order Sphingomonadales, and family Sphingomonadaceae. This carotenoid-producing strain is capable of degrading xenobiotics and is tolerant to toxic levels of six heavy metals. We have designated the newly isolated strain of S. yanoikuyae as S. yanoikuyae strain CC4533 (hereafter called strain CC4533) because it was isolated from a contaminated Tris-Acetate-Phosphate (TAP) medium culture plate of a green micro-alga Chlamydomonas reinhardtii wild type strain CC4533. We sequenced the whole genome of strain CC4533 using the PacBio Sequel II Continuous Long Read technology and have submitted it to NCBI along with the SRA and PacBio methylation motif data. Additionally, we have submitted the PacBio methylome to REBASE, Ref#35996. We present the whole genome sequence of S. yanoikuyae strain CC4533 that offers insights into its coding and non-coding genes and its nearest taxonomic neighbors.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Localized Strain Analysis of Ce- and Mg-Treated Cast Iron under Uniaxial Compression

Cast iron exhibits a wide range of mechanical properties, depending on its microstructural features. The microstructure of cast iron consists of several microconstituents with different elastic-plastic behavior, making the strain non-uniform across the bulk material. To understand the individual effects of these microconstituents on the overall mechanical behavior, local strain analysis using digital image correlation analysis was carried out. Samples with two different compositions (varying cerium, magnesium and silicon) were processed at different solidification velocities in a Bridgman furnace. Sections of the directionally solidified samples were loaded under uniaxial compression to measure global and local strain behavior. Despite the variability of the microstructure, the stress–strain curves obtained by digital image correlation (DIC) were found to react in a well-controlled way to changes in solidification velocity. It was observed that high-strain failure (greater than 15%) was accompanied by local straining of the softer ferritic phase, but during low-strain failure, local straining was not prominent. Higher nodularities, due to higher solidification velocities, raised the compressive strength without affecting the toughness significantly. Higher percentages of carbides led to higher compressive strengths with corresponding losses in ductility. The continuity of the matrix was also found to play an important role in the behavior during compression.

ductile failure↗

DOE OSTI2023

Genomic and Phenotypic Characterization of Shiga Toxin-Producing Escherichia albertii Strains Isolated from Wild Birds in a Major Agricultural Region in California

Escherichia albertii is an emerging foodborne pathogen. To better understand the pathogenesis and health risk of this pathogen, comparative genomics and phenotypic characterization were applied to assess the pathogenicity potential of E. albertii strains isolated from wild birds in a major agricultural region in California. Shiga toxin genes stx2f were present in all avian strains. Pangenome analyses of 20 complete genomes revealed a total of 11,249 genes, of which nearly 80% were accessory genes. Both core gene-based phylogenetic and accessory gene-based relatedness analyses consistently grouped the three stx2f-positive clinical strains with the five avian strains carrying ST7971. Among the three Stx2f-converting prophage integration sites identified, ssrA was the most common one. Besides the locus of enterocyte effacement and type three secretion system, the high pathogenicity island, OI-122, and type six secretion systems were identified. Substantial strain variation in virulence gene repertoire, Shiga toxin production, and cytotoxicity were revealed. Six avian strains exhibited significantly higher cytotoxicity than that of stx2f-positive E. coli, and three of them exhibited a comparable level of cytotoxicity with that of enterohemorrhagic E. coli outbreak strains, suggesting that wild birds could serve as a reservoir of E. albertii strains with great potential to cause severe diseases in humans.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2026

Velocity-space Origins of the Pressure–Strain Interaction in Multipopulation Distributions and Its Application to Magnetic Reconnection

A forefront research question is how energy evolves in weakly collisional plasmas for which departures from local thermodynamic equilibrium (LTE) are significant. The standard approach is studying the terms in the non-LTE energy evolution equation derived by taking the second moment of the Boltzmann equation, but the resultant fluid metrics do not retain information about which particles at which velocities drive energy evolution. A widely studied channel for internal energy density evolution is the pressure–strain interaction. Here, we employ the kinetic pressure–strain, a phase-space diagnostic whose velocity-space integral recovers the pressure–strain interaction to disambiguate the contributions to the pressure–strain interaction from disparate particle populations in composite phase-space densities. We develop phase-space analogs of the pressure–strain interaction decompositions to provide the phase-space origins of normal versus sheared flow. We introduce the “kinetic strain-rate” tensor, the phase-space analog of the strain-rate tensor, which we argue is needed to interpret the phase-space origins of the pressure–strain interaction. To demonstrate the utility of these quantities, we investigate them for composite electron distributions near the electron diffusion region in two-dimensional particle-in-cell simulations of antiparallel symmetric magnetic reconnection. We find that the phase-space-based diagnostics isolate the roles of distinct populations. These results contribute to a growing body of work providing new methods for quantifying phase-space energy evolution for a broad array of processes, from magnetic reconnection to collisionless shocks and turbulence, opening new pathways for answering longstanding problems of particle energization in weakly collisional plasmas.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1985

An update of the total-strain version of SRP

An updated procedure for characterizing an alloy and predicting cyclic life by using the total strain range version of strainrange partitioning (TS-SRP) has been developed. The principal feature of this update is a new procedure for determining the intercept of time dependent elastic strain range versus cyclic life lines. The procedure is based on an established relation between failure and the cyclic stress-strain response of an alloy. The stress-strain response is characterized by empirical equations presented in this report. These equations were determined with the aid of a cyclic constitutive model. The procedures presented herein reduce the testing required to characterize an alloy. Failure testing is done only in the high strain, low life regime; cyclic stress-strain response is determined from tests conducted in both the high and low strain regimes. These tests are carried out to stability of the stress-strain hysteresis loop but not to failure. Thus both the time and costs required to characterize an alloy are greatly reduced. This approach was evaluated and verified for two nickel base superalloys, AF2-1DA and Inconel 718.

Saltsman, J. F.↗

NASA NTRS1988

An update of the total-strain version of SRP

Saltsman, James F.↗

NASA NTRS1991

Mechanical strain isolator mount

Certain devices such as optical instruments must preserve their alignmental integrity while being subjected to mechanical strain. A mechanical strain isolator mount is provided to preserve the alignmental integrity of an alignment sensitive instrument. An alignment sensitive instrument is mounted on a rectangular base. Flexural legs are connected at their proximal ends to the rectangular base. Flexural legs are also spaced parallel to the sides. Mounting pads are connected to the legs at the distal end and the mechanical strain isolator mount is attached to the substrate by means of threaded bolts. When a mounting pad and its respective leg is subjected to lateral strain in either the X or Y direction via the substrate, the respective leg relieves the strain by bending in the direction of the strain. An axial strain on a mounting pad in the Z direction is relieved by a rotational motion of the legs in the direction of the strain. When the substrate is stress free, the flexural legs return to their original condition and thus preserve the original alignment integrity of the alignment sensitive instrument.

James, Gordon E.↗

NASA NTRS1991

High strain rate properties of unidirectional composites, part 1

Experimental methods were developed for testing and characterization of composite materials at strain rates ranging from quasi-static to over 500 s(sup -1). Three materials were characterized, two graphite/epoxies and a graphite/S-glass/epoxy. Properties were obtained by testing thin rings 10.16 cm (4 in.) in diameter, 2.54 cm (1 in.) wide, and six to eight plies thick under internal pressure. Unidirectional 0 degree, 90 degree, and 10 degree off-axis rings were tested to obtain longitudinal, transverse, and in-plane shear properties. In the dynamic tests internal pressure was applied explosively through a liquid and the pressure was measured with a calibrated steel ring. Strains in the calibration and specimen rings were recorded with a digital processing oscilloscope. The data were processed and the equation of motion solved numerically by the mini-computer attached to the oscilloscope. Results were obtained and plotted in the form of dynamic stress-strain curves. Longitudinal properties which are governed by the fibers do not vary much with strain rate with only a moderate (up to 20 percent) increase in modulus. Transverse modulus and strength increase sharply with strain rate reaching values up to three times the static values. The in-plane shear modulus and shear strength increase noticeably with strain rate by up to approximately 65 percent. In all cases ultimate strains do not vary significantly with strain rates.

Daniel, I. M.↗

NASA NTRS1991

High strain rate properties of angle-ply composite laminates, part 3

Angle-ply graphite/epoxy and graphite/S-glass/epoxy laminates were characterized in uniaxial tension at strain rates ranging from quasi-static to over 500 s(sup -1). Laminate ring specimens of +/-15(sub 2s), +/-22.5(sub 2s), +/-30(sub 2s), +/-45(sub 2s), +/-60(sub 2s), +/-67.5(sub 2s), and +/-75(sub 2s) degree layups were loaded under internal pressure. Results were presented in the form of stress-strain curves to failure. Properties determined included moduli, Poisson's ratios, strength, and ultimate strain. In all seven laminates for the two materials tested the modulus and strength increase with strain rate. The effect of strain rate varies with layup, being lowest for the fiber dominated +/-15(sub 2s) degree laminates and highest for the matrix dominated +/-75(sub 2s) degree laminates. The highest increments over the static values are 10 to 25 percent for the +/-15(sub 2s) degree layup and 200 to 275 percent for the +/-75(sub 2s) degree layup. Ultimate strains do not show any significant trends with strain rate. In almost all cases the ultimate strain values are within +/-20 percent of the mean value and in half of the cases the deviation from the mean are less than 10 percent.

Daniel, I. M.↗

NASA NTRS1991

Temperature effects on high strain rate properties of graphite/epoxy composites

A unidirectional graphite epoxy material (AS4/3501-6) was characterized at strain rates ranging from 5 x 10(exp 6) s(exp -1) to 5(exp -1), at room temperature and at 128 C. Results are presented in the form of stress-strain curves to failure. The longitudinal properties remain nearly unchanged with strain rate and temperature. The transverse modulus increases with strain rate but decreases with temperature. The transverse strength and transverse ultimate tensile strain have a positive rate sensitivity at low rates, which changes to negative at intermediate rates and returns to positive rate sensitivity at the highest rates tested. A temperature-time equivalence principle was applied and master curves were obtained for the transverse mechanical properties. The in-plane shear modulus and in-plane shear strength have a positive rate sensitivity. The ultimate intralaminar shear strain has a positive rate sensitivity at low rates, which changes to negative at high rates. At the elevated temperature of 128 C, the ultimate shear strain is 25 to 30 percent higher than the room temperature value, but its strain rate dependence is moderate.

Yaniv, G.↗

NASA NTRS1996

Strain Insensitive Optical Phase Locked Loop

An apparatus is provided to allow for quasi distributed sensing of strain within a test object. Strain insensitive fiber is used to deliver a light signal to a strain sensitive fiber in an optical phase locked loop sensor configuration. The use of strain insensitive delivery fiber allows for non-integrated measurements of strain without the use of expensive electronics such as those employed in ODTR techniques. The novelty of the present invention lies in the use of strain insensitive multimode fiber. The inventors had previously developed a similar sensor with strain insensitive fiber, however it was restricted to the use of single or few mode fibers. The use of an optical phase locked loop arrangement allows for the use of multimode strain insensitive fiber.

Egalon, Claudio Oliviera↗

NASA NTRS1999

Strain Gages in use at NASA Langley: A Technical Review

Surface mounted strain gages and strain gage application techniques are as varied as they are versatile. There is an abundance of technical literature, available throughout the strain gage community, offering techniques for installing strain gages and methods of obtaining useful information from them. This paper, while providing more of the same, will focus its discussions on recent Langley developments for using strain gages reliably and accurately in very harsh environments. With Langley's extensive use of wind tunnel balances, its ongoing effort in materials development, and its currently focused activities in structural testing, the use of strain gages in unusual and demanding environments has led to several innovative improvements in the "how to gage it" department. Several of these innovations will be addressed that hopefully will provide some practical information for the strain gage user who is finding the test environment and (or) the materials to be tested too demanding for previously utilized strain gage application technology. Specifically, this paper will include discussions in the following three areas: (1) technical considerations when gaging cryogenic wind tunnel balances, including areas for improving accuracy and reliability; (2) addressing technical difficulties associated with gaging composite test articles and certain alloys for testing at temperatures approaching -450F, or elevated temperatures up to 350F, or both temperatures inclusive during the same test scenario; (3) gaging innovations for testing metal/matrix and carbon/carbon composites at temperatures above 700F.

Moore, Thomas C., Sr.↗