Nonhybrid, finished microbial genome assemblies from long-read SMRT sequencing data
Explore the source record for details and available documents.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
In this work, we describe the design, fabrication, and characterization of purely mechanical miniature resonating structures that exhibit gyroscopic performance comparable to that of more complex microelectromechanical systems. Compared to previous implementations of Coriolis vibratory gyroscopes, the present approach has the key advantage of using excitation and probing that do not require any on-chip electronics or electrical contacts near the resonating structure. More specifically, our design relies on differential optical readout, each channel of which is similar to the 'optical lever' readout used in atomic force microscopy. The piezoelectrically actuated stage provides highly efficient excitation of millimeter-scale tuning fork structures that were fabricated using widely available high-throughput wafer-level silicon processing. In our experiments, reproducible responses to rotational rates as low as 1.8 × 10 3° h –1 were demonstrated using a benchtop prototype without any additional processing of the raw signal. The noise-equivalent rate, ΩNER, derived from the Allan deviation plot, was found to be <0.5° h –1 for a time of 10 3 s. Despite the relatively low Q factors (<10 4 ) of the tuning fork structures operating under ambient pressure and temperature conditions, the measured performance was not limited by thermomechanical noise. In fact, the performance demonstrated in this proof-of-principle study is approximately four orders of magnitude away from the fundamental limit.
Not Available
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Not provided.
Explore the source record for details and available documents.
We present light intensity dependent measurements of the quantum efficiency of P3HT:PCBM photovoltaic devices. Unlike previous studies we focus on ultralow light intensities down to 10{sup -3} mW/cm{sup 2}. We find that although when the devices are excited at intensities close to 1 Sun they exhibit very little bias or light intensity dependence, this is clearly not the case for light intensities below 1 mW/cm{sup 2}, where the cell's efficiency becomes highly dependent on the bias and light intensity. Using a simple model for the device efficiency we can fit the experimental data across a wide range of parameters and thus separate the effects of generation efficiency (geminate recombination) and charge recombination. Our finding suggests that recombination through trap (charge transfer) states is an important loss mechanism and we are able to quantify the density and depth of these states.
We present a scheme to measure the displacement of a nanomechanical resonator at cryogenic temperature. The technique is based on the use of a superconducting quantum interference device to detect the magnetic flux change induced by a magnetized particle attached on the end of the resonator. Unlike conventional interferometric techniques, our detection scheme does not involve direct power dissipation in the resonator, and therefore, is particularly suitable for ultralow temperature applications. We demonstrate its potential by cooling an ultrasoft silicon cantilever to a noise temperature of 25 mK, corresponding to a subattonewton thermal force noise of 0.5 aN/{radical}(Hz).
Abstract not provided
This paper is a review of recent progress of RD53 Collaboration. Results obtained on the study of the radiation effects on 65 nm CMOS have matured enough to define first strategies to adopt in the design of analog and digital circuits. Critical building blocks and analog very front end chains have been designed, tested before and after 5–800 Mrad. Small prototypes of 64×64 pixels with complex digital architectures have been produced, and point to address the main issues of dealing with extremely high pixel rates, while operating at very small in-time thresholds in the analog front end. Lastly, the collaboration is now proceeding at full speed towards the design of a large scale prototype, called RD53A, in 65 nm CMOS technology.
Explore the source record for details and available documents.
Abstract not provided
Explore the source record for details and available documents.
Not Available