Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer Matrix Composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

285 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Experimental Investigation on the Performance Loss of Cross-Linked Polymers During Photo-Oxidative Aging

Abstract Polymeric substances have seen an unprecedented integration in countless applications and fields of life, subjecting them to a broad range of environmental conditions, which can cause a form of damage to the structural and mechanical properties of these components known as aging. In this study we investigate the effects of the degradation of polymeric materials due to the extended exposure to sunlight, which can be simulated through controlled photo-oxidative aging using ultraviolet (UV) radiation as the main catalyst of this phenomenon. The effects on mechanical behavior and chemical properties of four polymeric materials with different mechanical characteristics was accordingly monitored throughout the study. The materials range in hardness with the polyurethane adhesive being the hardest and acting plastically, followed by an acrylic which exhibits greater hardening with time, a polyurethane sealant, which behaves in an elastomeric manner, and a silicon sealant, which is the softest of the set. Samples were prepared and subjected to UV radiation at three different temperatures namely 45, 60 and 80°C, for different aging periods ranging from 1 day for higher temperatures to 150 days for lower ones. The samples were then subjected to the Fourier transform Infrared spectroscopy (FTIR) test to monitor the change in the chemical composition of the materials along the aging durations and conditions. The materials were then subjected to mechanical testing along two modes of mechanical loading, which are a simple tension until failure and a double-cyclic test with progressively increasing strain limits after every two successful cycles until the sample reaches failure. The samples are loaded at constant strain rates throughout both tests. These tests revealed the change of behavior of our materials along the aging periods and conditions. The changes in mechanical behavior vary across each individual material depending on the aging temperature and period, with the changes ranging from hardening to softening, embrittlement or an increase in the maximum strain the material can endure before failure. A general trend would be that most materials become harder after photo-oxidation, however due to the range of temperatures in the aging conditions, thermo-oxidation, which causes softening in some of the polymers, has an increasingly notable effect at higher temperatures. A visible correlation can be noted between the change in mechanical behavior and a change in absorbance of Infrared Radiation (IR) in the FTIR spectrum, as the greater the crosslinking throughout the polymer matrix, the lower the absorbance of IR radiation due to the increased stiffness of the overall macro-molecular structure.

Korayem, Abd-Elrahman↗
DOE OSTI2024

Experimental and statistical study on the effect of process parameters on the quality of continuous fiber composites made via additive manufacturing

Ongoing research in additive manufacturing towards structural and industrial application has led to the use of commingled roving as a manufacturing feedstock for printing high fiber volume fraction composites. The prospects of using this technology for high performance applications necessitates the need for a comprehensive experimental investigation into the effects of processing parameters on the quality of an additively manufactured composite printed from commingled roving feedstock. Here, in this work, transverse flexure and void fraction matrix pyrolysis testing are both performed to evaluate composite quality. The transverse flexure test is a testing approach that evaluates the quality of the interfacial fiber-matrix bond while the void fraction test estimates the void content in the printed composite. A full observational study consisting of 27 different test combinations is done to investigate the effects of three different process parameters namely, temperature, pressure, and print speed across three different levels. Composite samples were made from commingled roving of E-glass and amorphous PET using an in-house built continuous fiber composite digital manufacturing system. Least squares regression analysis is performed to study the main, interaction and quadratic effects of process parameters. A statistical regression model having an R2 adjusted value of 80.1% is generated from the transverse flexure study, which is used to explain main and interaction effects and also predict performance. Response surface plots are also generated and are used to optimize process parameters which can subsequently be of help in scaling up composite manufacturing. Results show that all three process parameters are highly statistically significant at the 0.01 level of significance. Pressure * Temperature and Pressure * Printspeed are significant interaction terms. Pressure plays a weightier role when print speed is increased or temperature is decreased as it closes more voids that would ordinarily have been introduced because of drop in polymer melt viscosity. Micrographic analysis is also performed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tailoring compatibilization potential of maleic anhydride–grafted polypropylene by sequential rheochemical processing of polypropylene and polyamide 66 blends

Reactive compatibilization of immiscible polymer blends using a preferred compatibilizer leaves the following question: How much loading of a compatibilizer is good enough and what maximum properties can be achieved? A good understanding of the process can help solve the reutilization of mixed waste plastics. Here, the reactive compatibilization of polypropylene-graft-maleic anhydride (PP-g-MAH) on polypropylene/polyamide 66 (PP/PA66) blends is quantitatively assessed using thermorheological, microoptical, spectroscopic, and x-ray scattering-based characterization tools. The overall compositions of all PP(60%)/PA66(30%)/PP-g-MAH(10%) blends are kept constant while systematically controlling the degree of the chemical reaction by varying the sequential addition of PP-g-MAH to the melt mixture. The first feeding of PP-g-MAH (x%, 0 ≤ x ≤ 10) is conducted at 280°C and the second feeding of (10–x)% is at 200°C. During the first step, a larger amount of chemical activity is observed up to 4%–6% addition of PP-g-MAH. Furthermore, the constant chemical composition allows a systematic comparison of the compatibilizer-dependent thermal, rheological, morphological, and mechanical properties. With an increased degree of interfacial reaction, the size of dispersed PA66 domains decreases to register improved interfacial adhesion with the PP matrix, yielding enhanced Young's modulus and absolute failure strength of the isotropic matrix.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dynamic Control of Photocatalytic Proton Reduction through the Mechanical Actuation of a Hydrogel Host Matrix

This paper describes a photocatalytic hydrogen evolution system that is dynamically and reversibly responsive to the pH of the surrounding solution through actuation of a micro-hydrogel (microgel) matrix that hosts the photocatalysts (CdSe/CdS nanorods). Here, the reversible actuation occurs within 0.7 s (swelling) and 1.7 s (contraction). A ΔpH of 0.01 relative to the pK a of the tertiary amine on the microgel polymer (7.27) results in a reversible change in the average diameter of the microgel hosts by a factor of 2.5 and a change in the photocatalytic turnover frequency (TOF) by a factor of five. Kinetic isotope effect and photoluminescence quenching experiments reveal that the scavenging of the photoexcited hole by sulfite ions is the rate-limiting step and leads to the observed response of the TOF to pH through actuation of the microgel. Molecular dynamics simulations quantify a greater local concentration of sulfite hole scavengers for pH < pK a .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Accurate additive manufacturing of lightweight and elastic carbons using plastic precursors

Despite groundbreaking advances in the additive manufacturing of polymers, metals, and ceramics, scaled and accurate production of structured carbons remains largely underdeveloped. This work reports a simple method to produce complex carbon materials with very low dimensional shrinkage from printed to carbonized state (less than 4%), using commercially available polypropylene precursors and a fused filament fabrication-based process. The control of macrostructural retention is enabled by the inclusion of fiber fillers regardless of the crosslinking degree of the polypropylene matrix, providing a significant advantage to directly control the density, porosity, and mechanical properties of 3D printed carbons. Using the same printed plastic precursors, different mechanical responses of derived carbons can be obtained, notably from stiff to highly compressible. This report harnesses the power of additive manufacturing for producing carbons with accurately controlled structure and properties, while enabling great opportunities for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Degradable Biocomposite Thermoplastic Polyurethanes

In this project, the team developed tough and degradable biocomposite thermoplastic polyurethanes (TPUs) by incorporating bacterial spores into TPUs as a biofunctional living filler. The team screened various bacteria and selected the Bacillus subtilis ATCC 6633 strain as the final candidate, primarily due to its genomic availability, sporulation ability and TPU assimilation activity. The heat-shock tolerance of ATCC 6633 spores was further improved through evolutionary engineering via Adaptive Laboratory Evolution (ALE), demonstrating a 17.7-fold enhanced germination efficiency post heat-shock treatment compared to the wild-type strain (WT). The team fabricated biocomposite TPUs by incorporating lyophilized powder of heat-shock tolerized (HST) spores during the hot melt extrusion (HME) of TPU at 135 °C. The baseline TPU used in this project is a commercially available soft-grade TPU (BCF45) manufactured by BASF. Colony forming unit (CFU) assays quantified that WT and HST spores in the TPU matrix retained approximately 20% and 100% survivability, respectively, after HME. Tensile testing demonstrated that the spores behaved as a polymer-reinforcing filler, positively affecting the overall tensile properties of the biocomposite TPU. For example, biocomposite TPU with WT and HST spores (BC TPU WT and BC TPU HST , respectively) exhibited up to 25% and 37% improved toughness, respectively, compared to TPU without spores. BC TPU HST showed remarkably improved disintegration in autoclaved compost (92% mass loss in 5 months), which simulated a microbially poor environment for TPU degradation. When compared to TPU without spores (44% mass loss in 5 months) the acceleration of degradation is marked. Respirometry confirmed that 72% of BC TPU HST was biomineralized into CO2 within 6 months, indicating that spores in the biocomposite TPU were germinated by utilizing nutrients in the autoclaved compost, facilitating TPU degradation at the end of the material's life. The team demonstrated the scale-up of biocomposite TPU fabrication using continuous extrusion and injection molding techniques. Processing conditions optimized in a lab-scale microcompounder were successfully transferred to a continuous extruder with a 30-fold increased throughput. Biocomposite TPUs prepared using these industry-relevant processes showed comparable toughness improvements to samples prepared in the lab-scale extruder. Excitingly, following compounding in the pilot-extruder the composite material could be injection molded, while retaining high spore viability and similar toughness improvements. The team also found that spores in biocomposite TPU served as antioxidants, preventing toughness decay during the recycled extrusion of BC TPU HST . Long-term storage tests over one year showed that the addition of spores had no negative effect on the longevity of the TPU. Furthermore, the team demonstrated the fabrication of spore-bearing biocomposite polymers with other polyesters such as PBAT, PLA, and PCL. We obtained promising preliminary data that showed overall toughness improvements for all polymers with spore addition. Finally, life cycle assessment (LCA) and techno-economic analysis (TEA) were carried out, which indicated minimal additional cost of fabrication. Overall, a tough and degradable biocomposite thermoplastic was successfully developed through this project, with all tasks completed successfully, achieving >100% of the objectives.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nanoparticle Diffusion in Miscible Polymer Nanocomposite Melts

X-ray photon correlation spectroscopy measurements were used to quantify the dynamics of bare and bimodal grafted silica nanoparticles mixed with PEO melts of different molecular weights. In dilute polymer nanocomposite (PNC) samples, we find diffusive NP behavior as described by the Stokes–Einstein relationship so long as the adsorbed PEO polymer layer is taken into account in determining both the effective NP size and its role on composite viscosity. The size of this bound layer was found to be approximately 2R g , where R g is the chain radius of gyration. We also expanded our system to investigate how the dynamics of grafted NPs differ from bare NPs with an adsorbed layer. We showed that the dynamics again can be determined by an effective NP radius at a scale smaller than the effective interparticle spacing; however, at larger length scales, the morphology and grafting parameters play a major role in the system dynamics. These results allow us to quantify NP ordering driven by polymer crystallization. It has previously been speculated that behavior is controlled by the relative ratio of time scale of crystal growth and the diffusive time scale of the NPs, a Peclet number. When the former time scale is longer, then the NPs are expected to be segregated into the interlamellar amorphous zones, while the NPs are too slow to be reorganized in the opposite case. We show here that this conjecture is quantitatively correct and the demarcation in behavior occurs for Pe = 1. Thus, we provide a way to estimate a critical spherulite growth rate for any semicrystalline PNC, at which a given NP can be ordered. Together, the results of this study permit us to tunably design PNCs through directed dispersion of NPs in a polymer matrix.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental Comparison of Elastomeric Materials for Hydraulic Seal Durability under Reciprocating Conditions

Wave Energy Converters (WECs) rely on hydraulic Power Take-Off (PTO) systems to transform the kinetic energy of ocean waves into electricity, where hydraulic seals play a critical role in preventing fluid leakage and ensuring watertight operation under harsh marine conditions. However, seal degradation due to wear, fatigue, and corrosion remains a key challenge limiting system reliability and increasing maintenance costs. In this study, the tribological performance of elastomeric materials for hydraulic sealing applications that are based on commercial polyurethane and custom-compounded Ethylene Propylene Diene Monomer (EPDM) is investigated. Using a CSM tribometer, reciprocating wear tests were conducted in accordance with ASTM G133 under dry sliding conditions, with normal loads ranging from 3 to 10 N, and sliding speeds of 10 to 30 mm/s. Coefficient of friction (COF), specific wear rate, and worn surface morphology are evaluated to understand how load, velocity, and material composition affect seal durability. Improved wear stability and high Shore A hardness (93–94) were demonstrated by the commercial thermoplastic polyurethane (Duralast 4203 and 4758). EPDM-based compounds showed different filler-dependent behaviors, formulations filled with carbon black (E3) had the lowest wear rate (1.45 × 10?4 mm³ N?¹ m?¹) and increased load-bearing capacity, while samples modified with silica and plasticizer (E4, E5) had better conformability and damping but less hardness. Compounded EPDMs showed wider deformation zones because of their lower modulus and filler-matrix interfacial fluctuations, while commercial grades exhibited shallower wear scars (= 380 µm), according to optical profilometry. The Archard model-based lifetime estimation showed that, under 10 N and 30 mm/s, operational endurance ranged from 3.1 to 6.2 years. Because of its low wear rate and steady interfacial behavior, E3 had the longest anticipated life. For medium-load hydraulic sealing applications, these results demonstrate the possibility of customized EPDM formulations as affordable substitutes for commercial polyurethanes. They also offer a quantitative foundation for material selection and lifespan prediction.

Durability↗
DOE OSTI2022

Prediction of curing kinetics of resorcinol‐added resole phenolic resins using differential scanning calorimetry for the fabrication of carbon/carbon composites

Phenolic resins are commonly used as carbon precursors for the fabrication of carbon/carbon composites due to their high carbon yield and aromatic nature. To decrease curing times, acid catalysts are generally used, but the addition of resorcinol was found to have a similar effect while being incorporated into the resin matrix with no contamination or corrosion issues. In this work, the curing kinetics of pure, 10, 20, and 30 wt% resorcinol-added phenolic resins were investigated through differential scanning calorimetry. Heating rates of 0.5, 1, 2.5, and 5°C min -1 were used with several curing models to predict isothermal curing. Averaged mean absolute error (MAE) for the isoconversional mathematical approaches namely Kissinger–Akahira–Sunose (MAE = 12.9 min), Flynn–Wall–Ozawa (15.8 min), and Vyazovkin (14 min) show that these methods provide the best predictions, attributed to their adoption of an activation energy that depends on the extent of cure (E a (α)). The Kissinger method (MAE = 36 min), which depends only on peak temperature with a constant activation energy assumption, and the data noise sensitive Friedman model (MAE = 1144.7 min) provide the least accurate results. Thermogravimetric analysis revealed that resorcinol decreases the curing times by up to 71% without lowering carbon yield.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrospun Hybrid Perfluorosulfonic Acid/Sulfonated Silica Composite Membranes

Electrospinning was employed to fabricate composite membranes containing perfluorosulfonic acid (PFSA) ionomer, poly(vinylidene fluoride) (PVDF) reinforcement and a sulfonated silica network, where the latter was incorporated either in the PFSA matrix or in the PVDF fibers. The best membrane, in terms of proton conductivity, was made by incorporating the sulfonated silica network in PFSA fibers (Type-A) while the lowest conductivity membrane was obtained when sulfonated silica was incorporated into the reinforcing PVDF fibers (Type-B). A Type-A membrane containing 65 wt.% PFSA with an embedded sulfonated silica network (at 15 wt.%) and with 20 wt.% PVDF reinforcing fibers proved superior to the pristine PFSA membrane in terms of both the proton conductivity in the 30–90% RH at 80 °C (a 25–35% increase) and lateral swelling (a 68% reduction). In addition, it was demonstrated that a Type-A membrane was superior to that of a neat 660 EW perfluoroimide acid (PFIA, from 3M Co.) films with respect to swelling and mechanical strength, while having a similar proton conductivity vs. relative humidity profile. This study demonstrates that an electrospun nanofiber composite membrane with a sulfonated silica network added to moderately low EW PFSA fibers is a viable alternative to an ultra-low EW fluorinated ionomer PEM, in terms of properties relevant to fuel cell applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Triple Layer Tungsten Trioxide, Graphene, and Polyaniline Composite Films for Combined Energy Storage and Electrochromic Applications

Different polyaniline (PANI)-based hybrid films were successfully prepared by electro-polymerizing aniline monomers onto pre-spin-coated indium tin oxide (ITO) glass slides with WO 3 , graphene, or WO 3 /graphene films. Comparing with pristine PANI, the shifts of the characteristic peaks of PANI-based nanocomposites in UV-visible absorption spectra (UV-vis) and Fourier transform infrared spectroscopy (FT-IR) indicate the chemical interaction between the PANI matrix and the nanofillers, which is also confirmed by the scanning electron microscope (SEM) images. Corresponding coloration efficiencies were obtained for the WO 3 /PANI (40.42 cm 2 C -1 ), graphene/PANI (78.64 cm 2 C -1 ), and WO 3 /graphene/PANI (67.47 cm 2 C -1 ) films, higher than that of the pristine PANI film (29.4 cm 2 C -1 ), suggesting positive effects of the introduced nanofillers on the electrochromic performance. The areal capacitances of the films were observed to increase following the order as bare WO 3 < WO 3 /graphene < pristine PANI < WO 3 /PANI < graphene/PANI < WO 3 /graphene/PANI films from both the cyclic voltammogram (CV) and galvanostatic charge-discharge (GCD) results. The enhanced energy storage and electrochromic performances of the PANI-based nanocomposite films can be attributed to the capacitance contributions of the introduced nanofillers, increased PANI amount, and the rougher morphology due to the embedment of the nanofillers into the PANI matrix. This extraordinary energy storage and electrochromic performances of the WO 3 /graphene/PANI film make it a promising candidate for combined electrochromic and energy storage applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pretreatment of Biomass by Selected Type-III Deep Eutectic Solvents and Evaluation of the Pretreatment Effects on Hydrothermal Carbonization

Hydrothermal carbonization (HTC) is a novel thermochemical conversion that converts wet biomass into energy dense solid fuel. Residual moisture under subcritical conditions reacts with a lignin-cellulose-hemicellulose matrix with the major reactions being identified as dehydration and decarboxylation. Among other reaction parameters (e.g., temperature, time, pressure), biomass morphology often plays a key role in HTC. The hypothesis of this study was enhancing the porous structure of biomass without significantly affecting biopolymer composition would augment hydrothermal carbonization (HTC). To prove the hypothesis, two type-III deep eutectic solvents (DESs), namely choline chloride:urea (ChCl:Urea, 1:2 mol/mol) and methyltriphenylphosphonium bromide:ethylene glycol (MTPB:EG, 1:4 mol/mol), were studied to pretreat loblolly pine at room temperature and ambient pressure for 1 h. DES pretreatment shows swelling of the biomass, increasing the surface fiber-to-fiber gap length by 52% and 185% for ChCl:Urea and MPTB:EG pretreatments, respectively. The total pore volume remained intact (2.6 × 10 –3 cm 3 /g), although new small pores evolved, and existing pores were abated with DES pretreatment. Hydrochars prepared from DES pretreated loblolly pine showed a high O/C and H/C ratio resulting in a significant increase of energy content (up to 42%) and a decrease of mass yield (up to 50 wt %), indicating an enhancement of HTC severity due to the alteration of surface morphology by DES. Finally, a preliminary process economics revealed that integrated DES pretreatment-HTC would increase fixed capital investment but decrease the cost of operation and manufacturing than the standalone HTC process.

09 BIOMASS FUELS↗
DOE OSTI2023

Assessment and Non-Destructive Evaluation of the Influence of Residual Solvent on a Two-Part Epoxy-Based Adhesive Using Ultrasonics

Polymers are increasingly being used in higher demanding applications due to their ability to tailor the properties of structures while allowing for a weight and cost reduction. Solvents play an important role in the manufacture of polymeric structures since they allow for a reduction in the polymer’s viscosity or assist with the dispersion of fillers into the polymer matrix. However, the incorrect removal of the solvent affects both the physical and chemical properties of polymeric materials. The presence of residual solvent can also negatively affect the curing kinetics and the final quality of polymers. Destructive testing is mainly performed to characterize the properties of these materials. However, this type of testing involves using lab-type equipment that cannot be taken in-field to perform in situ testing and requires a specific sample preparation. Here, a method is presented to non-destructively evaluate the curing process and final viscoelastic properties of polymeric materials using ultrasonics. In this study, changes in longitudinal sound speed were detected during the curing of an aerospace epoxy adhesive as a result of variations in polymer chemistry. To simulate the presence of residual solvent, samples containing different weight percentages of isopropyl alcohol were manufactured and tested using ultrasonics. Thermogravimetric analysis was used to show changes in the decomposition of the adhesive due to the presence of IPA within the polymer structure. Adding 2, 4, and 6 wt.% of IPA decreased the adhesive’s lap shear strength by 40, 58, and 71%, respectively. Ultrasonics were used to show how the solvent influenced the curing process and the final sound speed of the adhesive. Young’s modulus and Poisson’s ratio were determined using both the longitudinal and shear sound speeds of the adhesive. Using ultrasonics has the potential to non-invasively characterize the quality of polymers in both an in-field and manufacturing settings, ensuring their reliability during use in demanding applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Comprehensive Data Analysis and Analytic Method Development for PBX9501 Material (FY2019 Annual Report of Aging and Lifetimes Program)

In the polymer bonded explosive (PBX) 9501, a binder consisting of 2.5 wt% nitroplasticizer (NP) and 2.5 wt% Estane R 5703 (Estane) is combined with 94.9 wt% of the high-explosive HMX and 0.1 wt% stabilizer. Because of its flexibility and tensile strength, this binder lowers the sensitivity and improves the manufacturability of PBX 9501. However, like many plasticizers comprised of low molecular weight components, NP has a tendency to diffuse out of the PBX 9501 matrix and can decompose at moderate temperatures into reactive byproducts, such as NO, NO 2 , H 2 O, and HNO x . Through oxidation and hydrolysis, these molecules can further degrade NP and Estane, ultimately degrading the properties of PBX 9501. While gaseous molecules can readily diffuse out of the PBX 9501 charges, the intermediates with lower volatility are more likely trapped in the condensed phase inside the charges and, in a closed system, will co-exist with Estane for an extended period of time creating an ongoing reactive environment. Understanding the rates of formation for these volatiles and intermediates during the NP degradation is therefore a critical prerequisite for understanding the long-term stability of polymeric binders used in munition systems. To work toward this ultimate goal, in the past year, we have conducted comprehensive studies on the physical properties of NP and finished three-year long aging experiment to understand the aging behavior of NP under thermal treatment. Important results are summarized in this annual report. Although NP is widely used in the DOE complex, their physical properties are rather scattered and inconsistent in the open literature. For example, there are at least two widely different values, 14.5°C and -15°C, for the melting point of NP. Although it is known that NP is a eutectic 50:50 mixture of BDNPA and BDNPF, their eutectic phase diagram is not well documented. Furthermore, the effect of temperature on the miscibility between water and eutectic BDNPA/F mixture is rarely reported. To fill these knowledge gaps, a large set of BDNPA/F mixtures with BDNPA concentration ranging from 0 to 100 wt% was analyzed using DSC techniques. In addition to determining the eutectic melt point as -25°C, a phase diagram of the BDNPA/F system was constructed from -30°C to 45°C. With this phase diagram, the phase transition temperatures and composition can be readily found for the BDNPA/F mixtures with various mass ratios.

36 MATERIALS SCIENCE↗