SEARCH · Engineering Papers

Results for “PASSIVATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

DOE OSTI2015

Passivation of c-Si surfaces by sub-nm amorphous silicon capped with silicon nitride

A sub-nm hydrogenated amorphous silicon (a-Si:H) film capped with silicon nitride (SiN{sub x}) is shown to provide a high level passivation to crystalline silicon (c-Si) surfaces. When passivated by a 0.8 nm a-Si:H/75 nm SiN{sub x} stack, recombination current density J{sub 0} values of 9, 11, 47, and 87 fA/cm{sup 2} are obtained on 10 Ω·cm n-type, 0.8 Ω·cm p-type, 160 Ω/sq phosphorus-diffused, and 120 Ω/sq boron-diffused silicon surfaces, respectively. The J{sub 0} on n-type 10 Ω·cm wafers is further reduced to 2.5 ± 0.5 fA/cm{sup 2} when the a-Si:H film thickness exceeds 2.5 nm. The passivation by the sub-nm a-Si:H/SiN{sub x} stack is thermally stable at 400 °C in N{sub 2} for 60 min on all four c-Si surfaces. Capacitance–voltage measurements reveal a reduction in interface defect density and film charge density with an increase in a-Si:H thickness. The nearly transparent sub-nm a-Si:H/SiN{sub x} stack is thus demonstrated to be a promising surface passivation and antireflection coating suitable for all types of surfaces encountered in high efficiency c-Si solar cells.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Efficient passivation of n-type and p-type silicon surface defects by hydrogen sulfide gas reaction

An efficient surface defect passivation is observed by reacting clean Si in a dilute hydrogen sulfide-argon gas mixture (< 5% H2S in Ar) for both n-type and p-type Si wafers with planar and textured surfaces. Surface recombination velocities of 1.5 and 8 cm/s are achieved on n-type and p-type Si wafers, respectively, at an optimum reaction temperature of 550oC that are comparable to the best surface passivation quality used in high efficiency Si solar cells. Surface chemical analysis using x-ray photoelectron spectroscopy shows that sulfur is primarily bonded in a sulfide environment, and synchrotron-based soft x-ray emission spectroscopy of the adsorbed sulfur atoms suggests the formation of S-Si bonds. Furthermore, the sulfur surface passivation layer is unstable in air, attributed to surface oxide formation and a simultaneous decrease of sulfide bonds. However, the passivation can be stabilized by a low-temperature (300oC) deposited amorphous silicon nitride (a-Si:NX:H) capping layer.

14 SOLAR ENERGY↗

DOE OSTI2015

Amorphous/crystalline silicon interface passivation: Ambient-temperature dependence and implications for solar cell performance

Silicon heterojunction (SHJ) solar cells feature amorphous silicon passivation films, which enable very high voltages. We report how such passivation increases with operating temperature for amorphous silicon stacks involving doped layers and decreases for intrinsic-layer-only passivation. We discuss the implications of this phenomenon on the solar cell's temperature coefficient, which represents an important figure-of-merit for the energy yield of devices deployed in the field. We show evidence that both open-circuit voltage (Voc) and fill factor (FF) are affected by these variations in passivation and quantify these temperature-mediated effects, compared with those expected from standard diode equations. We confirm that devices with high Voc values at 25°C show better high-temperature performance. Thus, we also argue that the precise device architecture, such as the presence of charge-transport barriers, may affect the temperature-dependent device performance as well.

14 SOLAR ENERGY↗

DOE OSTI2018

Sputter-Deposited Oxides for Interface Passivation of CdTe Photovoltaics

Commercial CdTe PV modules have polycrystalline thin films deposited on glass, and devices made in this format have exceeded 22% efficiency. Devices made by the authors with a magnesium zinc oxide window layer and tellurium back contact have achieved efficiency over 18%, but these cells still suffer from an open-circuit voltage far below ideal values. Oxide passivation layers made by sputter deposition have the potential to increase voltage by reducing interface recombination. CdTe devices with these passivation layers were studied with photoluminescence (PL) emission spectroscopy and time-resolved photoluminescence (TRPL) to detect an increase in minority carrier lifetime. Because these oxide materials exhibit barriers to carrier collection, micropatterning was used to expose small point contacts while still allowing interface passivation. TRPL decay lifetimes have been greatly enhanced for thin polycrystalline absorber films with interface passivation. Device performance was measured and current collection was mapped spatially by light-beam-induced current.

14 SOLAR ENERGY↗

DOE OSTI2019

Modifications of Textured Silicon Surface Morphology and Its Effect on Poly-Si/SiO x Contact Passivation for Silicon Solar Cells

High-efficiency crystalline silicon (c -Si) solar cells require textured surfaces for efficient light trapping. However, passivation of a textured pyramidal surface to reduce carrier recombination is challenging due to the presence of sharp tips, edges, and valleys. Using electrical and surface microscopies combined with lifetime measurements, we report on the effect of HF:HNO3 etching on the pyramidal textured Si surface morphology, and on poly-Si/SiOx contact performance. Preferential rounding of either the valleys between pyramids, or the pyramid tips is obtained depending on the HF:HNO3 solution temperature. Both these morphologies make the pyramid shape irregular, with the pyramid faces no longer being predominantly a Si(111) surface. Our atomic force microscopy measurements further show that the nanoscale roughness over the pyramid face also reduces after HF:HNO3 etching. Thus, etching affects the microscopic pyramidal shape, the dominant crystallographic orientation, and the nanoscale roughness of the surface. We speculate that these three surface effects result in the improvement of surface passivation via poly-Si/SiOx contacts. However, this improved passivation is accompanied by increased reflectance of the HF:HNO3-etched textured surface. Finally, our electron-beam-induced current measurements reveal thickness nonuniformities in the thermally grown SiOx layer on the HF:HNO3-etched textured Si surface: SiO x is thicker near the pyramid tips, edges, and faces as compared with near the valleys between pyramids. This nonuniformity in the SiOx layer may explain the poorer passivation obtained on a KOH-textured and HF:HNO3-etched textured surface as compared with a planar surface.

14 SOLAR ENERGY↗

DOE OSTI2015

Ion Implanted Passivated Contacts for Interdigitated Back Contacted Solar Cells

We describe work towards an interdigitated back contacted (IBC) solar cell utilizing ion implanted, passivated contacts. Formation of electron and hole passivated contacts to n-type CZ wafers using tunneling SiO2 and ion implanted amorphous silicon (a-Si) are described. P and B were ion implanted into intrinsic amorphous Si films at several doses and energies. A series of post-implant anneals showed that the passivation quality improved with increasing annealing temperatures up to 900 degrees C. The recombination parameter, Jo, as measured by a Sinton lifetime tester, was Jo ~ 14 fA/cm2 for Si:P, and Jo ~ 56 fA/cm2 for Si:B contacts. The contact resistivity for the passivated contacts, as measured by TLM patterns, was 14 milliohm-cm2 for the n-type contact and 0.6 milliohm-cm2 for the p-type contact. These Jo and pcontact values are encouraging for forming IBC cells using ion implantation to spatially define dopants.

14 SOLAR ENERGY↗

DOE OSTI2024

Passivation Mechanisms in Locally Etched P-Type Poly-Si on Silicon Nitride/Silicon Oxide Stack

Tunneling oxide passivated contacts are quickly becoming the industry standard for high-efficiency c-Si based photovoltaic cells. Further development of these structures is essential to enable higher efficiencies and better reliability of cells. By utilizing poly-Si/SixNy/SiOx stacks, very high efficiencies have been demonstrated on small area cells. In this work we investigate the cause of the excellent passivation seen by these structures and show that the primary reason of the excellent passivation seen is the blocking B diffusion to the SiOx/c -Si interface. We also show that the interface between the silicon nitride and polysilicon affects B diffusion through to the c-Si interface. Finally, we demonstrate that the composition of the nitride used is of great importance, and that an incorrect nitride composition leads to B diffusion, and is directly correlated to poor passivation performance.

industries↗

DOE OSTI2019

Experimental Study and Model Predictive Control of a Lean-Burn Gasoline Engine Coupled With a Passive Selective Catalytic Reduction System

Lean-burn gasoline engines have reflected 10–20% engine efficiency gain over stoichiometric engines and are widely considered as a promising technology for meeting the 54.5 miles-per-gallon (mpg) corporate average fuel economy standard by 2025. Nonetheless, nitrogen oxides (NO x ) emissions control for lean-burn gasoline for meeting the stringent Environmental Protection Agency tier 3 emission standards has been one of the main challenges toward the commercialization of highly efficient lean-burn gasoline engines in the United States. Passive selective catalytic reduction (SCR) systems, which consist of a three-way catalyst (TWC) and SCR, have demonstrated great potentials of effectively reducing NO x emissions for lean gasoline engines at low cost. Yet, passive SCR operation may cause significant fuel penalty since rich engine combustion is required for ammonia generation. The purpose of this study is to develop a model-predictive control (MPC) scheme for a lean-burn gasoline engine coupled with a passive SCR system to minimize the total equivalent fuel penalty associated with passive SCR operation while satisfying stringent NO x and ammonia (NH 3 ) emissions requirements. Simulation results demonstrate that the MPC approach can reduce the fuel penalty by 43.9% in a simulated US06 cycle and 28.0% in a simulated urban dynamometer driving schedule (UDDS) cycle, respectively, compared to the baseline control, while achieving over 97% DeNO x efficiency and less than 15 ppm tailpipe ammonia slip. The proposed MPC controller can potentially enable highly efficient lean-burn gasoline engines while meeting the stringent Environmental Protection Agency tier 3 emission standards.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2018

Shallow Cumulus Macrophysical Properties at Midcontinental US Site: Integrated Multiyear Active and Passive Observations

Substantial difference between cloud amounts obtained from active and passive remote sensing has been documented by previous studies. The difference is typically attributed to two main factors: the different field-of-view (FOV) (first factor) and different sensitivity to cloud properties (second factor) of the active and passive ground-based instruments. The relative impact of these two main factors on shallow cumuli cloud amount is demonstrated in this study. The demonstration involves a new multi-year (2000-2017) product, which integrates both the active and passive remote sensing data collected at the mid-continental Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) Central Facility. Cloud fraction (CF) obtained from the narrow-FOV lidar-radar observations and wide-FOV fractional sky cover (FSC) acquired from sky images are key components of the integrated product. Results of this study indicate that (1) CF tends to overestimate FSC and this overestimation can be large (~40% on average) even at extended temporal scales (several years) and (2) the observed overestimate is primarily due to different sensitivity of the active and passive remote sensing instruments to shallow cumuli, while the limited FOV of active remote sensing instruments plays a minor role in such overestimation.

ARM Active Remotely Sensed Clouds Locations (ARSCL↗

DOE OSTI2021

Self-assembled multifunctional nanostructures for surface passivation and photon management in silicon photovoltaics

This work reports the fabrication and characterization of multifunctional, nanostructured passivation layers formed using a self-assembly process that provide both surface passivation and improved light trapping in crystalline silicon photovoltaic (PV) cells. Scalable block copolymer self-assembly and vapor phase infiltration processes are used to form arrays of aluminum oxide nanostructures (Al 2 O 3 ) on crystalline silicon without substrate etching. The Al 2 O 3 nanostructures are characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and spectroscopic ellipsometry. Injection-level dependent photoconductance measurements are used to determine the effective carrier lifetime of the samples to confirm the nanostructures successfully passivate the Si surface. Finite element method simulations and reflectance measurement show that the nanostructures increase the internal rear reflectance of the PV cell by suppressing the parasitic optical losses in the metal contact. An optimized morphology of the structures is identified for their potential use in PV cells as multifunctional materials providing surface passivation, photon management, and carrier transport pathways.

14 SOLAR ENERGY↗

DOE OSTI2014

Hood River Passive House, Hood River, Oregon (Fact Sheet)

The Hood River Passive Project was developed by Root Design Build of Hood River Oregon using the Passive House Planning Package (PHPP) to meet all of the requirements for certification under the European Passive House standards. The Passive House design approach has been gaining momentum among residential designers for custom homes and BEopt modeling indicates that these designs may actually exceed the goal of the U.S. Department of Energy's (DOE) Building America program to "reduce home energy use by 30%-50%" (compared to 2009 energy codes for new homes). This report documents the short term test results of the Shift House and compares the results of PHPP and BEopt modeling of the project. The design includes high R-Value assemblies, extremely tight construction, high performance doors and windows, solar thermal DHW, heat recovery ventilation, moveable external shutters and a high performance ductless mini-split heat pump. Cost analysis indicates that many of the measures implemented in this project did not meet the BA standard for cost neutrality. The ductless mini-split heat pump, lighting and advanced air leakage control were the most cost effective measures. The future challenge will be to value engineer the performance levels indicated here in modeling using production based practices at a significantly lower cost.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2016

Electroless Plated Nanodiamond Coating for Stainless Steel Passivation

Tritium gas sample bottles and manifold components require passivation surface treatments to minimize the interaction of the hydrogen isotopes with surface contamination on the stainless steel containment materials. This document summarizes the effort to evaluate electroless plated nanodiamond coatings as a passivation layer for stainless steel. In this work, we developed an electroless nanodiamond (ND)-copper (Cu) coating process to deposit ND on stainless steel parts with the diamond loadings of 0%, 25% and 50% v/v in a Cu matrix. The coated Conflat Flanged Vessel Assemblies (CFVAs) were evaluated on surface morphology, composition, ND distribution, residual hydrogen release, and surface reactivity with deuterium. For as-received Cu and ND-Cu coated CFVAs, hydrogen off-gassing is rapid, and the off-gas rates of H 2 was one to two orders of magnitude higher than that for both untreated and electropolished stainless steel CFVAs, and hydrogen and deuterium reacted to form HD as well. These results indicated that residual H 2 was entrapped in the Cu and ND-Cu coated CFVAs during the coating process, and moisture was adsorbed on the surface, and ND and/or Cu might facilitate catalytic isotope exchange reaction for HD formation. However, hydrocarbons (i.e., CH 3 ) did not form, and did not appear to be an issue for the Cu and ND-Cu coated CFVAs. After vacuum heating, residual H 2 and adsorbed H 2 O in the Cu and ND-Cu coated CFVAs were dramatically reduced. The H 2 off-gassing rate after the vacuum treatment of Cu and 50% ND-Cu coated CFVAs was on the level of 10 -14 l mbar/s cm 2 , while H 2 O off-gas rate was on the level of 10 -15 l mbar/s cm 2 , consistent with the untreated or electropolished stainless steel CFVA, but the HD formation remained. The Restek EP bottle was used as a reference for this work. The Restek Electro-Polished (EP) bottle and their SilTek coated bottles tested under a different research project exhibited very little hydrogen off-gassing and unmeasurable HD formation. ND and Cu were initially chosen to develop improved passivation technology, because Cu has a lower permeability of hydrogen, and diamond is more inert than other materials under a hydrogen atmosphere. However, our tests demonstrated that even after an 8-18 day vacuum extraction heat treatment, the electroless plated Cu and ND-Cu coated stainless steel CFVAs exhibited H 2 off-gassing rates that were just comparable to those for the untreated or electropolished stainless steel CFVA, and the HD formation was still observed. Thus, the Restek Electro-Polished (EP) bottle outperformed the electroless plated Cu and ND-Cu coated stainless steel CFVAs, and the electroless plated nanodiamond coating is not promising as a surface passivation technology. However, the ND-Cu coating may be beneficial to another application in which catalyzing the H 2 -D 2 exchange reaction is desired.

08 HYDROGEN↗

DOE OSTI2021

AOI [1]: Passive Wireless Sensor Systems Fabricated by Direct-Writing for Temperature and Health Monitoring of Energy Systems in Harsh-Environments (Final Report)

Researchers at West Virginia University (WVU) propose to demonstrate a wireless, high-temperature sensor system for monitoring the temperature and health of energy-system components. The active sensor and electronics for wireless communication will be composed entirely of an electroceramic materials (conductive ceramics) which are capable of withstanding the harsh-environments required for fossil energy-based technologies. This work will focus primarily on the fabrication and testing of temperature (thermocouples and thermistors) and health (strain/stress and crack propagation sensors) that function at extreme temperatures (up to 700-1700ºC). The electronics will accompany the high-temperature sensor, which will include a passive wireless communication circuit that allows the transmission of the data based on the LCR resonance principle to a near-by reader antenna. This passive transmission of data will reduce the need for interconnect wires near the active, and possibly rotating, energy-system component. The research will include process development to permit the 2D/3D direct-writing of the entire sensor and communication circuit onto the energy-system component. The direct-writing will be facilitated by using silicon-based polymer-derived precursors to form the high-temperature, stable electroceramic compositions. In addition, methods for direct-writing the circuit onto a fugitive carrier substrate will be completed, which will permit a “peel-and-stick”-like transfer of the sensor circuit to the energy-system component. This feature will allow the economical and precise placement of the sensor circuit onto components of various shapes and locations, without altering the geometry and active features of the manufactured component, or the removal (or decommissioning) of the component for installation. The proposed work will be directed at the following areas: 1) Investigation of phase formation, sintering/grain growth, and electrical properties of polymer-derived electroceramic composites; 2) Definition of processes to direct-write through ink-jet and robo-casting the polymer-derived electroceramic composites onto oxide and polymer surfaces; 3) Development of methods to form monolithic "peel-and-stick" preforms that will efficiently transfer the sensor circuit to ceramic surfaces after thermal treatment; 4) Design of passive wireless LCR circuits and receiver (reader) antennas for communication and testing at high temperatures; 5) Investigation of the passive wireless sensor system developed (and method of transferring sensor system) for temperature and stress/strain measurements on a SOFC repeat unit and a singular gas turbine blade prototype as example applications.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Approaching the Radiative Efficiency Limit in Perovskite Solar Cells with Scalable Defect Passivation and Selective Contacts

This award aimed to enable perovskite solar cells to approach the radiative efficiency limit in scalable manufacturing environments by controlling recombination losses, especially surface recombination losses at electrodes and interfaces. The project combined organic molecular synthesis, perovskite film processing and characterization, and spectroscopic tool development for probing recombination centers. The project ultimately achieved record-low surface recombination velocity (SRV) in mixed cation methylammonium-free perovskite thin films, demonstrated photoluminescence as an effective process metrology tool to optimizing processing of device stacks, and showed that the aminopropyltrimethoxysilane (APTMS) is suitable for passivating the exposed perovskite interface in p-i-n stack devices. The project used combinations of phosphonic acids to modify the transparent conducting oxide and APTMS to passivate the perovskite/electron transport layer interface, thereby demonstrating reduction of SRVs in both partial and full device stacks. The project showed concomitant improvements in device performance, and demonstrated that APTMS passivation was compatible with large area coating of external stakeholder perovskite films using both scalable solution and vapor methods. Notably, the project also supplied surface passivating materials to a number of other US based and SETO-funded teams.

14 SOLAR ENERGY↗

NASA NTRS2018

Polarization Decomposition and Temperature Bias Resolution for SMAP Passive Soil Moisture Retrieval Using Time Series Brightness Temperature Observations

In passive microwave remote sensing of soil moisture, the tau-omega (τ-ω) model has often been used to provide soil moisture estimates at a spatial scale representative of the satellite footprint dimensions. For modeling simplicity, model parameters such as the single scattering albedo (ω) and vegetation opacity (τ) that go into the geophysical inversion process are often assumed to be independent of polarizations. Although this absence of polarization dependence can often be justified in special cases as in low-frequency remote sensing or under dense vegetation conditions, it is not a robust assumption in general. Additional model parameterization errors arising from this assumption are possible, leading to degradation in soil moisture estimation accuracy. In this paper, we propose a time series approach to try to resolve the polarization dependence of several τ-ω model parameters as well as the temperature bias arising from the ancillary temperature data. The Version 4 of the Soil Moisture Active Passive (SMAP) Level 1B brightness temperature time series observations were used to illustrate the mechanics of this approach, with an emphasis on a comparison between resulting satellite soil moisture retrievals and in situ data collected at several core validation sites. It was found that this time series approach resulted in significant reduction of the dry bias exhibited in the current SMAP passive soil moisture data products, while retaining the same performance in other metrics of the current baseline passive soil moisture retrieval algorithm.

time series↗

NASA NTRSDate not supplied

Passive Dust Mitigation Technologies Being Developed for Demonstration Under Patch Plate Materials Compatibility Analysis Task

With the Artemis program, we are planning longer stays on the surface, with more activities that have the potential to put the astronauts and equipment in contact with greater quantities of lunar dust. The success of these missions will depend on our understanding of material interactions with lunar dust and the development of ways to mitigate dust effects in cases where exposure to dust will lead to failure of components, unacceptable loss of power or thermal control, unacceptable loss of visibility, or health issues. Passive dust mitigation by coating or surface alteration is one method that is being developed and demonstrated under the Space Technology Mission Directorate’s Game Changing Technology, Dust Mitigation Program as part of the Patch Plate Materials Compatibility Assessment Task. The goal of the task is to alter the surfaces of materials in order to passively reduce the adhesion of dust, demonstrate their performance in relevant ground-based tests using lunar simulants, and prepare them for demonstration through experiment on the lunar surface. Optically transparent, sputter deposited, work function matching coatings are being developed to reduce adhesion of dust to windows, lenses and display panels by matching the minimum energy to remove an electron from the surface to that of lunar dust in order to reduce adhesion due to charge transfer. Low surface energy coatings and surfaces for thermal control are also being developed to reduce the bonding of dust with the surface enabling it to be removed more easily. Conductive coatings with the ability to shed dust more easily are being developed for use with the active Electrodynamic Dust Shield technology to help reduce the power needed to remove dust from the surface. Passive dust mitigation surfaces for metals such as aluminum, stainless steel, and titanium are being developed that reduce the area of dust contact with the surfaces through topographical modification using laser ablation patterning to impart hierarchical topographies with nanometer to micrometer length scales in a single step. Topographically modified polymeric materials, both those with extensive space heritage and those with lower technology readiness levels, are also being evaluated. Space suit fabric surfaces that can reduce dust penetration into and through the fabric are also being investigated as well as pristine and topographically modified ceramic materials that exhibit high wear resilience. An overview of the passive dust mitigation surfaces and coatings being developed under this task, ground testing being conducted using lunar simulants, characterization techniques, and materials preparation for flight sample delivery for integration into the Alpha Space Regolith Adherence Characterization experiment going to the lunar surface on a Commercial Lunar Payload Services (CLPS) lander in 2023 will be discussed.

Lunar dust, passive mitigation, lunar simulant, co↗

NASA NTRS2022

On the Effects of Cloud Water Content on Passive Microwave Snowfall Retrievals

The Bayesian passive microwave retrievals of snowfall often rely on mathematical matching of the observed vectors of brightness temperature with an a priori database of precipitation profiles and their corresponding brightness temperatures. Mathematical proximity does not necessarily lead to consistent retrievals due to limited information content of passive microwave observations. This paper defines imposter (genuine) vectors of brightness temperature as those that are mathematically close but physically inconsistent (consistent) and characterizes them through the Silhouette Coefficient (SC) analysis. The Neyman–Pearson (NP) hypothesis testing is used to separate the imposter and genuine brightness temperatures based on their associated values of cloud ice (IWP) and liquid water path (LWP), given by coincidences of CloudSat Profiling Radar (CPR) and the Global Precipitation Measurement (GPM) Microwave Imager (GMI). The study determines thresholds for IWP and LWP that allow optimal identification of imposter brightness temperatures of non-snowing and snowing clouds, which can mislead the passive microwave retrieval algorithms to falsely detect or miss the snowfall events. It is demonstrated that emission signal of supercooled liquid water in snowing clouds can lead to improved passive microwave retrieval of snowfall and conditioning the retrievals to the cloud IWP and LWP can result in marginal correction of the snowfall detection probability; however, reduce the probability of false alarm by 6%–8% over sea ice and open oceans.

Snowfall↗

NASA NTRS2023

Passively Cooled Superconductors Final Report

A highly reflective spray-on coating and tile material has been under development at Kennedy Space Center (KSC) that scatters away most of the Sun’s energy, thereby allowing coated objects to remain cool in space. The best performing tile material has achieved 1% solar absorptivity while the best performing spray-on coating has achieved around 4%. Both versions passively maintain cryogenic temperatures below 120 K at 1 astronomical unit (AU) from the Sun, but the tile material consistently sustains temperatures below 90 K, which is low enough to preserve oxygen and methane in a liquid state. Besides keeping propellants cold, this “solar white” material has the potential to passively maintain high-temperature superconductors (HTS) in a superconducting state without the support of liquid nitrogen cooling. If superconductors can be operated without the added infrastructure of liquid nitrogen cooling, it may enable them to be used in space for applications like magnetic radiation shielding and efficient energy management. Long duration exposure to both galactic cosmic radiation and coronal mass ejections can pose health risks for the astronauts and increase the potential for damage to electronics. This makes shielding essential to accomplish long duration missions, particularly when astronauts are onboard. The objective of this project was to determine the extent we could keep a high-temperature superconducting (HTS) material passively chilled to maintain its superconducting state. Both the tile and spray-on versions of solar white were investigated. We focused on finding a version that could support passive cooling at 1 AU from the Sun and determined the closest operating distances for samples that were unable to perform at 1 AU. Early in the project, we selected bismuth strontium calcium copper oxide (BSCCO) as the HTS to test based on its reputable usage in superconducting wires. The version we selected was Bi-2223, which has a critical temperature of about 108 K. Sample bars with contacts for a four-point probe were obtained from Quantum Levitation: https://quantumlevitation.com/product/superconductor-bar-for-4-point-tc-experiment/.

superconductors↗