Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nuclear Repository”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

ORNL Input to GDSA Repository Systems Analysis FY21

This document satisfies the M3 milestone M3SF-21OR010304082 titled “ORNL Input to GDSA Repository Systems.” This document describes the current status of Oak Ridge National Laboratory’s (ORNL’s) efforts related to analyses of dual-purpose canister (DPC) disposal in unsaturated alluvium with a focus on thermal hydrological constraints on criticality timing and power output. This analysis updates previous analyses of thermal hydrological constraints on timing and power output of a potential criticality event in Dual-Purpose Canisters (DPCs) in a hypothetical repository in unsaturated alluvium using a more realistic representation of heat transport inside dry DPCs. PFLOTRAN was used for the simulations of multiphase thermal hydrology near a single DPC. The scenario considers a DPC failure at 9000 years, allowing water to enter and eventually fill the DPC. Once the DPC is filled to a level that could support a criticality event, different values for criticality power output were added to the decay heat. The main objective is to bound the power output that could be produced by a criticality event without driving water out of the package. For the conditions analyzed here, following a package breach, the alluvial formation could supply enough water to allow enough accumulation in the DPC to support a criticality event. However, the power output that would be generated is limited to modest values by loss of water moderator due to evaporation and vapor diffusion. In the reference case scenario, the DPC would not start to fill with water until about 16,000 years post closure and would not fill to a level that allows a criticality event until approximately 25,000 years post closure. The long-term average power output that could be sustained without driving off the water and terminating the criticality event is limited to approximately 100 W. Sensitivity to assumed conditions and parameters in the reference case, especially the deep percolation rate, need to be addressed but could not be undertaken because of numerical failures of the PFLOTRAN code running in general mode in the dry conditions of an unsaturated alluvium repository

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Initial Investigation of Coupled Electron-Photon Transport with SCEPTRE and RAPTURE (Rev.1.1)

The SCEPTRE1 code models coupled photon and electron transport in material media using discrete ordinates methods. The code can use different solvers in 1D and 3D in parallel, promising users the ability to run problems that are significant both in physics and computational scale. One capability that is perhaps unique at this time in the NNSA complex is SCEPTRE’s coupled photon– electron transport physics in a discrete ordinates approach. For example, incident x–rays can generate a significant electron population, whose transport can be simulated within the same code. In this context, fully–coupled means that photons can produce electrons and electrons can produce photons; uncoupled or no–coupling means photons do not produce electrons. Partial–coupling, an intermediate option in which photons can produce electrons but electrons do not produce photons, is not considered in the present work. The MCNP code can treat this physics with a Monte Carlo approach. MCNP should be viewed as complementary to SCEPTRE in both computational method (Monte Carlo versus discrete ordinates) as well as data libraries. SCEPTRE and MCNP should provide important checks on each other, especially from complementary modeling frameworks of a S n (discrete ordinates) mesh based method versus Monte Carlo particle based method. In order to learn more about SCEPTRE, and how it might inform engineering work at the Laboratory, we used it to carry out a set of initial studies. This was a series of 1D simulations of photon beams hitting Aluminum slabs. Our studies mainly used SCEPTRE directly, and made little use of the closely associated RAPTURE code (more on this below). The goals of these studies were first, to familiarize ourselves with operating the code, and second, to begin to assess the importance of coupled electron–photon transport. To support these studies, we began to develop a set of scripts to initialize inputs, run tools, process outputs, and plot results. An initial version of these scripts has been committed to the Lightning workflow repository. This memo relates the results of those studies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

The iodine-129 paradox in nuclear waste management strategies

Nuclear energy has an important role in the low-carbon energy transition, but the safety of spent nuclear fuel (SNF) management remains a public concern. Here, in this study, we investigate the interplay between waste management strategies and their environmental impacts with a particular focus on a highly mobile and persistent radionuclide, iodine-129 (I-129), which is the dominant risk contributor from SNF disposal and at existing groundwater contamination sites. The results show that the current recycling practice releases more than 90% of I-129 in SNF into the present-day biosphere using an isotropic dilution strategy, whereas the direct disposal of SNF in geological repositories is likely to delay and reduce the release by 8 orders of magnitude. In addition, our data synthesis of surface water concentrations near four nuclear facilities shows that the release-dilution strategy results in lower concentrations than regulatory standards, while insufficient waste isolation in the past has resulted in locally high concentrations within one site. Our analysis suggests that it is essential to consider effluents more explicitly as a part of the waste, that as society moves from dilution to isolation of waste, the potential risks of waste isolation to local regions should be carefully evaluated, and that excessive burdens of proof could hinder or discourage waste isolation. Comprehensive waste management strategies—considering not just volume but also mobility, isolation technologies and ultimate fates—are needed for persistent contaminants. This study offers valuable insights for optimizing the management of SNF and other persistent contaminants.

Wainwright, Haruko M. [Massachusetts Inst. of Tech↗
DOE OSTI2021

Continuous Integration, In-Code Documentation, and Automation for Nuclear Quality Assurance Conformance

The Multiphysics Object Oriented Simulation Environment (MOOSE) is an open-source, finite element framework for solving highly coupled sets of nonlinear equations. The development of the framework and applications occurs concurrently using an agile, continuous-integration software package. Included in the framework is an in-code, extensible documentation system. Using these two tools in union with the repository management tools GitHub and GitLab, a software quality plan was created and followed such that MOOSE and a MOOSE-based application (BISON) have been shown to meet the American Society of Mechanical Engineers’ Nuclear Quality Assurance-1 standard. The approach relies heavily on automation for both testing and documentation. The resulting effort demonstrates that a rigorous software quality plan may be implemented that incurs a minimal impact on day-to-day development of the software, satisfying the stringent guidelines necessary to operate the software in a safety function within a nuclear facility.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Preliminary Reporting of Thermophysical Property Measurements for the Ghareb Formation

Accurate knowledge of thermophysical properties of rock is vital to develop meaningful models of high level nuclear waste emplacement scenarios. The Israel Atomic Energy Commission is considering storing high level nuclear waste in the Ghareb formation, a porous kerogen bearing chalk. Sandia is supporting this effort with an evolving lab- based geomechanics testing program. We have completed measurements of thermal properties up to 275C and room temperature hydrostatic compaction measurements. We report thermal conductivity, thermal diffusivity, specific heat, and mass loss from our thermal measurements, and we report bulk moduli and porosity loss from our compaction measurements. These values are crucial for the numerical models to simulate heat transfer and formation compressibility around a heat generating repository.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Application of Particle Accelerators to Mitigate Energy and Climate Change Problems Facing America

Reliable CO 2 -free baseload power is needed to address ever-increasing demands for electricity while minimizing adverse climate change. Diversified power supply provided by solar, wind, geothermal, and nuclear reactors can displace the use of fossil fuels. The United States (U.S.) is taking a new look at nuclear power as a source of electrical energy and the nuclear industry is proposing new approaches which may minimize capital costs. However, nuclear power comes with a variety of technical problems. Chief among those is managing the used fuel from nuclear reactors. No long-term, practicable solution to this problem is available. The lack of progress on a comprehensive waste management strategy restricts growth in the nuclear power industry and minimizes the role that nuclear energy may serve as part of a zero-carbon future (Bahr, 2021). According to the Nuclear Waste Policy Act of 1982, as amended, the U.S. Government has possession of the used reactor fuel and incurs large annual storage fees paid to utilities to store and safeguard the accumulated used fuel. In effect, short term on-site storage of nuclear waste is the current waste management plan. The amount of used reactor fuel in the U.S. is approximately 80,000 metric tons. While no geologic repository exists within the U.S., the potential site at Yucca Mountain, NV would accommodate 70,000 metric tons, which fails to meet current and future needs. Given the technical and political challenges associated with establishing a single geological storage site, it is necessary for the U.S. to implement technologies that improve the suitability of geological storage by reducing the volume and radiotoxicity of stored material. No extant technology meets this need. Accelerator driven waste burners have been proposed as a scalable method to process used nuclear fuel, however considerable technical challenges remain which impede commercialization. Innovations in design require investigation of novel materials, development of accurate models and simulations, and a comprehensive assessment of safety and performance. This proposal elaborates how LANL is uniquely positioned to make key contributions to this area of research.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Effect of pore fluid chemistry on the mechanical behavior of a divalent compacted bentonite, an experimental and constitutive study

Ongoing research in isolating high-level nuclear waste and spent fuel has highlighted compacted bentonite as a suitable material for engineered barrier systems in deep geological repositories due to its extraordinary swelling and retention properties. This research focuses on the chemo-mechanical behavior of compacted bentonite exposed to different pore fluids with different concentrations and loading conditions. The study involves swelling pressure and compressibility experiments along with mineralogy analysis employing X-ray diffraction (XRD) and Cation exchange. The tests were conducted on BCV (a Mg/Ca- bentonite) compacted at a dry density of 1.48 ± .02 Mg/m 3 . An advanced chemical-mechanical constitutive model for unsaturated highly expansive clays was adopted to simulate the material response and better understand its behavior. The model is able to account for the main phenomena at both macro and microstructural levels and the interactions between them. The model successfully replicated experimental observations. The XRD analyses support the macroscopic observation, indicating that salinity impacts crystalline swelling as demonstrated by the reduction of basal spacing from 19.27 Å to 15.68 Å when the osmotic suction increases from 0 MPa to 33 MPa. The results suggested that the osmotic pressure generated by the concentration in the pore fluids promotes a reduction in swelling pressures, swelling strains, and crystalline swelling of clay minerals. Also, it affects the pre-consolidation stress and the compressibility of the compacted samples. In conclusion, it was also observed that both solution type and solution concentration impact the clay swelling pressure.

Chemo-mechanical constitutive model↗
DOE OSTI2023

Tabulated equations of state from models informed by chiral effective field theory

Abstract We construct four equation of state (EoS) tables, tabulated over a range of temperatures, densities, and charge fractions, relevant for neutron star applications such as simulations of neutron star mergers. The EoS are computed from a relativistic mean-field theory constrained by the pure neutron matter EoS from chiral effective field theory, inferred properties of isospin-symmetric nuclear matter, and astrophysical observations of neutron star structure. To model nuclear matter at low densities, we attach an EoS that models inhomogeneous nuclear matter at arbitrary temperatures and charge fractions. The four EoS tables we develop are available from the CompOSE EoS repository https://compose.obspm.fr/eos/297 and gitlab.com/ahaber/qmc-rmf-tables .

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

The effect of cerium, neodymium, and ytterbium doping on UO 2 dissolution

Here, the dissolution rate of spent nuclear fuel has been studied heavily to understand the impacts of a failed waste package scenario on potential radionuclide release from a geologic repository. Multiple countries have evaluated these scenarios in oxidizing and reducing environments respective to their relevant repository conditions. The repository environment (e.g., water chemistry, temperature, oxygen content) and the fuel itself (e.g., chemical content of the fuel) both heavily impact the dissolution rate of the spent fuel. This work examined the impact that rare earth element dopants (Ce, Nd, Yb) have on the fuel dissolution under repository relevant conditions with decreasing oxidizing conditions using a single pass flowthrough system. UO 2 samples were doped with Ce, Nd, or Yb with concentrations between 1 and 5 at%. The addition of dopants to the samples reduced the dissolution rates on most samples relative to pure UO 2 samples. Scoping experiments that occurred in a less oxidizing environment showed a reduction in dissolution rate compared to fully oxidizing conditions. The results within highlight the importance of dopant behavior in used fuel dissolution modeling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Baseline Postirradiation Examination of the FUTURIX-FTA Experiments

Postirradiation Examination (PIE) results from the baseline examination of the FUTURIX-FTA irradiation experiment are presented in this report. The FUTURIX-FTA irradiation was designed to study the fuel performance of candidate transmutation fuels. The FUTURIX-FTA experiment was conducted in the true fast neutron spectrum conditions of the Phénix sodium fast test reactor in France. FUTURIX-FTA contained several compositions that were also irradiated as part of the AFC-1 test in cadmium filtered positions in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) that approximate the neutron spectrum of a fast reactor. This experiment was a joint collaboration between the Department of Energy (DOE) in the U.S. and the Commissariat á l'Energie Atomique et aux Energies Alternatives (CEA) in France. A joint agreement between DOE and CEA was established in 2004 to conduct an irradiation experiment of metallic and nitride fuels in the Phénix reactor at CEA. Both the FUTURIX-FTA tests and the AFC-1 tests were conducted for the DOE Advanced Fuels Campaign (AFC) that is part of Fuel Cycle Research & Development (FCRD) program. These programs seek to develop and demonstrate the technologies needed to transmute long-lived transuranic actinide isotopes contained in spent nuclear fuel via fast reactor technology. The long term goal of this work is to reduce the radiotoxicity of future high level waste repositories. Post-irradiation examination of irradiated fuels experiments provides data related to in reactor fuel performance and input into future fuel design choices. The compositions of the FUTURIX-FTA pins were designed to test if minor actinides could be incorporated into the fuel of a fast reactor without significantly changing fuel performance observed for previously well studied fuels. The fuel performance of metallic fuel in fast reactors has been well documented. Likewise the irradiation performance of nitride fuels in fast reactors has also been documented. However the existing database for nitride fuels is much smaller than the database for metal fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Engineered Barrier System Research Activities at LBNL (FY2020 Progress Report)

The design of a radioactive waste repository typically involves a multi-barrier system, including the natural barrier system (NBS), i.e., the host rock and its surrounding subsurface environment, and an engineered barrier system (EBS). The EBS is to be constructed from the man-made, engineered materials placed within a repository. The repository includes the waste form, waste canisters, buffer materials, backfill, and seals. The most common buffer material for EBS is compacted bentonite, which features low permeability and high retardation of radionuclides. Extensive studies concerning the behavior of bentonite backfill in crystalline and argillite/shale geologic environments for nuclear waste disposal have been conducted by means of laboratory experiments, numerical modeling, and large-scale in situ tests in Underground Research Laboratories (URLs) in Switzerland, France, Belgium, and Japan. This report includes the results of LBNL’s research activities conducted according to the objectives and scope of the work packages “SF-20LB01030802 Engineered Barrier System R&D - LBNL” and “SF-20LB01030806 Engineered Barrier System International Collaborations - LBNL” of the Spent Fuel and Waste Science and Technology (SFWST) (formerly called Used Fuel Disposal) Campaign of the Department of Energy’s (DOE) Office of Nuclear Energy. LBNL research studies included laboratory scale tests and modeling of the evolution of the EBS bentonite and associated coupled processes, and impacts of high temperature on parameters and processes relevant to the performance of crystalline and argillite repositories, including the evaluation of the technical basis for applying the maximum allowable temperature. The results of these studies are being addressing the technical elements necessary to evaluate the EBS design concepts. Emphasis is on the study of thermal, mechanical, and chemical processes that influence the performance of EBS, and the development of modeling capability for reliable assessment of these processes, and ultimately supporting the development of the GDSA model with detailed coupled THMC process models.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Improbability of Post-Closure Criticality in Array of Transuranic Waste Containers after Compaction by Salt Creep at Waste Isolation Pilot Plant

Based on the rationale presented, post-closure nuclear criticality is improbable when room closure compacts containers disposing transuranic (TRU) waste emplaced at the Waste Isolation Pilot Plant (WIPP), an operating repository in bedded salt in southeastern New Mexico. As described in the original WIPP certification, a qualitative estimate of the probability of post-closure criticality in TRU waste produced from atomic energy defense activities has been low either because remote-handled TRU waste canisters are neutronically isolated by the bedded salt or because the low fissile mass in an array of contact-handled TRU waste drums cannot be compacted sufficiently by room closure from salt creep. These situations are still valid for the majority of TRU waste that is disposed at WIPP without any disposal constraints, as updated herein. This report also qualitatively evaluates the probability of criticality after disposal of TRU waste in pipe overpack containers (POC) where every POC in a shipment may have the maximum 200 fissile gram equivalent of 239Pu content. The probability of criticality for a disposal room filled with POCs is estimated during four representative phases of repository evolution: (1) a large salt block falls onto POCs in the first 20 years, (2) salt creep closes a disposal room in the first 1000 years without brine seepage and subsequent gas generation, which permits maximum compaction, (3) some brine seepage occurs into the closed room, which initiates consumption of the fiberboard (cellulose) impact absorber in the POC in the second 1000 years, and (4) full brine inundation of a room and consumption of all fiberboard thereafter. Salt-block fall in the first phase does not greatly disrupt three tiers of POCs. The compacted spacing of POCs in the later three repository conditions is calculated through high-fidelity, geomechanical modeling. Criticality evaluation of compacted 200-g 239 Pu spheres at the compacted spacing shows that neither 12-inch nor 6-inch POCs are critical after the first 1000 years, the second 1000 years, or thereafter as the sea of reflector material changes to represent the three repository conditions. Specifically, fiberboard and iron isolates 239 Pu while dry, and brine reduces the reactivity when a room is partially and fully inundated. Because POC behavior bounds behavior of other standard TRU waste containers, post-closure criticality caused by room closure compacting containers is omitted in the performance assessments for the 2019 and 2026 WIPP compliance re-certification applications to the US Environmental Protection Agency.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

EXCESS workshop: Descriptions of rising low-energy spectra

Many low-threshold experiments observe sharply rising event rates of yet unknown origins below a few hundred eV, and larger than expected from known backgrounds. Due to the significant impact of this excess on the dark matter or neutrino sensitivity of these experiments, a collective effort has been started to share the knowledge about the individual observations. For this, the EXCESS Workshop was initiated. In its first iteration in June 2021, ten rare event search collaborations contributed to this initiative via talks and discussions. The contributing collaborations were CONNIE, CRESST, DAMIC, EDELWEISS, MINER, NEWS-G, NUCLEUS, RICOCHET, SENSEI and SuperCDMS. They presented data about their observed energy spectra and known backgrounds together with details about the respective measurements. In this paper, we summarize the presented information and give a comprehensive overview of the similarities and differences between the distinct measurements. The provided data is furthermore publicly available on the workshop's data repository together with a plotting tool for visualization.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Geologic Disposal Safety Assessment (GDSA) Biosphere Model Development

The Spent Fuel and Waste Science and Technology Campaign of the U.S. Department of Energy Office of Nuclear Energy, Office of Spent Fuel and Waste Disposition is conducting research and development on geologic disposal of spent nuclear fuel and high-level nuclear waste. This work includes the Geologic Disposal Safety Assessment (GDSA) program which is charged with development of generic deep geologic repository concepts and system performance assessment models. One part of the GDSA framework is the development of a biosphere model capable of assessing doses to potential receptors exposed to radionuclides released from geologic disposal sites. As part of the GDSA framework, a biosphere model compatible with the PFLOTRAN massively parallel subsurface flow and reactive transport code is under development. The PFLOTRAN model provides the radionuclide source term for the biosphere model. The GDSA Biosphere model then assesses the potential movement of radionuclides through the surface biosphere and the subsequent exposure to a human receptor living in the biosphere. The biosphere model includes pathways originating from the groundwater as well as pathways originating from surface water bodies that have a water exchange with a contaminated groundwater body. The pathways for human exposure include consumption of drinking water, irrigated crops, meat animals, aquatic vegetation, and animals, etc.; external exposure from irrigated ground surfaces, surface water bodies, recreational activities, etc.; and inadvertent exposures such as ingestion of contaminated soils or shower water, etc. The GDSA Biosphere model was designed to be flexible and generic in order to accommodate a variety of different sites and climate states. This presentation will present the on the purpose, design, and development progress of the GDSA Biosphere Model.

GDSA, biosphere, repository↗
DOE OSTI2023

Metallographic examinations and hydrogen measurements of high-burnup spent nuclear fuel cladding

In the US, commercial spent nuclear fuel (SNF) is transferred to interim dry storage casks where it will be stored for decades awaiting transport to a consolidated interim storage facility or a geologic repository. Because the fuel rod cladding is the first barrier against any radioactive material release, understanding the behavior of SNF cladding, particularly at high burnup (HBU), in dry storage conditions is crucial to safely store and transport the spent fuel. In this study, a series of metallographic examinations and cladding hydrogen measurements were conducted on HBU SNF cladding at Oak Ridge National Laboratory as a part of the High Burnup Spent Fuel Data Project, which is sponsored by the US Department of Energy (DOE) Office of Nuclear Energy (NE). Here, t o investigate the effect of simulated drying conditions on the cladding, three as-received fuel rods with different cladding materials—M5, ZIRLO, and Zircaloy-4—were heated to 400°C and then slow-cooled to room temperature. The pellet and cladding were then qualitatively and quantitatively analyzed and compared in terms of pellet crack morphology, HBU rim, waterside oxide, cladding H, and cladding hydride morphologies. This paper presents and discusses the results of these analyses in detail.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Validation of MCNP Critical Benchmarks Models of Highly Enriched Uranium Cylinders

A new centralized repository of high-quality MCNP models of critical benchmark experiments is currently under development at Los Alamos National Laboratory (LANL). The benchmark experiments are described in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook, and the initial set of benchmark models are derived from the Whisper Suite provided with MCNP6.2. This effort is a collaboration among the Nuclear Criticality Safety, Nuclear Data, and Monte Carlo code development/application organization at LANL. The objective is to create a current single LANL benchmark collection that includes the latest ICSBEP revision that has a formal review and revision process, is contained in an open- source repository, and utilizes new Python tools for improved input and output file review.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Sensitivity analysis of generic deep geologic repository with focus on spatial heterogeneity induced by stochastic fracture network generation

Geologic Disposal Safety Assessment Framework is a state-of-the-art simulation software toolkit for probabilistic post-closure performance assessment of systems for deep geologic disposal of nuclear waste developed by the United States Department of Energy. This paper presents a generic reference case and shows how it is being used to develop and demonstrate performance assessment methods within the Geologic Disposal Safety Assessment Framework that mitigate some of the challenges posed by high uncertainty and limited computational resources. Variance-based global sensitivity analysis is applied to assess the effects of spatial heterogeneity using graph-based summary measures for scalar and time-varying quantities of interest. Behavior of the system with respect to spatial heterogeneity is further investigated using ratios of water fluxes. This analysis shows that spatial heterogeneity is a dominant uncertainty in predictions of repository performance which can be identified in global sensitivity analysis using proxy variables derived from graph descriptions of discrete fracture networks. New quantities of interest defined using water fluxes proved useful for better understanding overall system behavior.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗