Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Millimeter-wave”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Active CPW-fed slot antennas for power combining applications

We have combined integrated circuit antenna technology with microwave oscillator design to build an active slot-oscillator. The design is planar, does not require via holes and is compatible with monolithic transistor technology. The CPW-fed antenna impedance is calculated using a full-wave analysis technique. Slot-oscillators were built at 7, 13, and 22 GHz, and the predicted oscillation frequencies agree well with experiments. The design is easily scaled to millimeter-wave frequencies and can be extended to power combining arrays.

Kormanyos, Brian K.↗
NASA NTRS1992

Quasi-optical antenna-mixer-array design for terahertz frequencies

A new quasi-optical antenna-mixer-array design for terahertz frequencies is presented. In the design, antenna and mixer are combined into an entity, based on the technology in which millimeter-wave horn antenna arrays have been fabricated in silicon wafers. It consists of a set of forward- and backward-looking horns made with a set of silicon wafers. The front side is used to receive incoming signal, and the back side is used to feed local oscillator signal. Intermediate frequency is led out from the side of the array. Signal received by the horn array is picked up by antenna probes suspended on thin silicon-oxynitride membranes inside the horns. Mixer diodes will be located on the membranes inside the horns. Modeling of such an antenna-mixer-array design is done on a scaled model at microwave frequencies. The impedance matching, RF and LO isolation, and patterns of the array have been tested and analyzed.

Guo, Yong↗
NASA NTRS1992

Embedding impedance approximations in the analysis of SIS mixers

Future millimeter-wave radio astronomy instruments will use arrays of many SIS receivers, either as focal plane arrays on individual radio telescopes, or as individual receivers on the many antennas of radio interferometers. Such applications will require broadband integrated mixers without mechanical tuners. To produce such mixers, it will be necessary to improve present mixer design techniques, most of which use the three-frequency approximation to Tucker's quantum mixer theory. This paper examines the adequacy of three approximations to Tucker's theory: (1) the usual three-frequency approximation which assumes a sinusoidal LO voltage at the junction, and a short-circuit at all frequencies above the upper sideband; (2) a five-frequency approximation which allows two LO voltage harmonics and five small-signal sidebands; and (3) a quasi five-frequency approximation in which five small-signal sidebands are allowed, but the LO voltage is assumed sinusoidal. These are compared with a full harmonic-Newton solution of Tucker's equations, including eight LO harmonics and their corresponding sidebands, for realistic SIS mixer circuits. It is shown that the accuracy of the three approximations depends strongly on the value of omega R(sub N)C for the SIS junctions used. For large omega R(sub N)C, all three approximations approach the eight-harmonic solution. For omega R(sub N)C values in the range 0.5 to 10, the range of most practical interest, the quasi five-frequency approximation is a considerable improvement over the three-frequency approximation, and should be suitable for much design work. For the realistic SIS mixers considered here, the five-frequency approximation gives results very close to those of the eight-harmonic solution. Use of these approximations, where appropriate, considerably reduces the computational effort needed to analyze an SIS mixer, and allows the design and optimization of mixers using a personal computer.

Kerr, A. R.↗
NASA NTRS1992

94 GHz integrated horn monopulse antennas

A monolithic azimuthal monopulse antenna for 94 GHz applications has been developed. The structure consists of a single dipole suspended in one plane of an integrated horn cavity to obtain the sum pattern, and an antiparallel pair of dipoles suspended in a different plane of the same horn cavity to achieve the difference pattern. Pattern measurements of microwave models and on the millimeter-wave antennas show good agreement with theory and exhibit symmetry with a sharp -30 dB null at broadside for the difference antenna. Microwave model measurements show input impedances close to 50 Ohms, with greater than -25 dB isolation between sum and difference antennas across a 10 percent bandwidth.

Ling, Curtis C.↗
NASA NTRS1991

Mixed application MMIC technologies - Progress in combining RF, digital and photonic circuits

Approaches for future 'mixed application' monolithic integrated circuits (ICs) employing optical receive/transmit, RF amplification and modulation and digital control functions are discussed. We focus on compatibility of the photonic component fabrication with conventional RF and digital IC technologies. Recent progress at Honeywell in integrating several parts of the desired RF/digital/photonic circuit integration suite required for construction of a future millimeter-wave optically-controlled phased-array element are illustrated.

Swirhun, S.↗
NASA NTRS1991

Phase shifter technology assessment - Prospects and applications

Capabilities and limitations of MMIC phase shifter technology at microwave and millimeter wave frequencies are reviewed. MMIC-based phase arrays make it possible to integrate active elements at the array face, i.e., to incorporate transmit power amplifiers and/or low noise amplifiers at each antenna element. Active elements make it possible to increase power efficiency and reliability and provide graceful degradation. Monolithic integration of the various transmit/receive functions including phase shifting is considered to be feasible through at least the lower millimeter-wave frequency range (about 30-100 GHz). MMIC integration also allows more flexibility in array design including those that are intended for airborne conformal applications.

Sokolov, Vladimir↗
NASA NTRS1991

Comparative study of bolometric and non-bolometric switching elements for microwave phase shifters

The performance of semiconductor and high critical temperature superconductor switches is compared as they are used in delay-line-type microwave and millimeter-wave phase shifters. Such factors as their ratios of the off-to-on resistances, parasitic reactances, power consumption, speed, input-to-output isolation, ease of fabrication, and physical dimensions are compared. Owing to their almost infinite off-to-on resistance ratio and excellent input-to-output isolation, bolometric superconducting switches appear to be quite suitable for use in microwave phase shifters; their only drawbacks are their speed and size. The SUPERFET, a novel device whose operation is based on the electric field effect in high critical temperature ceramic superconductors is also discussed. Preliminary results indicate that the SUPERFET is fast and that it can be scaled; therefore, it can be fabricated with dimensions comparable to semiconductor field-effect transistors.

Tabib-Azar, Massood↗
NASA NTRS1992

Sensors and sensor systems for guidance and navigation II; Proceedings of the Meeting, Orlando, FL, Apr. 22, 23, 1992

Topics discussed in this volume include aircraft guidance and navigation, optics for visual guidance of aircraft, spacecraft and missile guidance and navigation, lidar and ladar systems, microdevices, gyroscopes, cockpit displays, and automotive displays. Papers are presented on optical processing for range and attitude determination, aircraft collision avoidance using a statistical decision theory, a scanning laser aircraft surveillance system for carrier flight operations, star sensor simulation for astroinertial guidance and navigation, autonomous millimeter-wave radar guidance systems, and a 1.32-micron long-range solid state imaging ladar. Attention is also given to a microfabricated magnetometer using Young's modulus changes in magnetoelastic materials, an integrated microgyroscope, a pulsed diode ring laser gyroscope, self-scanned polysilicon active-matrix liquid-crystal displays, the history and development of coated contrast enhancement filters for cockpit displays, and the effect of the display configuration on the attentional sampling performance.

Welch, Sharon S.↗
NASA NTRS1993

A search for the rotational transitions of H2D+ at 1370 GHz and H3O+ at 985 GHz

A search was made for the 1370 GHz lowest rotational transition of the molecular ion H2D+ in NGC 2264, W3, and the IRc2 region of M42. No emission lines were seen, but an absorption feature was detected toward IRc2. The column density and fractional abundance were calculated using a tentative identification of the line as the transition of para H2D+. The LSR velocity and the measured line width are consistent with the dynamical parameters of the hot core source. Physical parameters deduced from the data differ from those derived from millimeter-wave observations of the hot core condensation. It is suggested that significant amounts of low-density gas are associated with this region and that the material is cold enough for enhanced deuterium fractionation to occur. A search was also made for the 985 GHz transition of ortho H3O+ in W3 and IRc2 with negative results.

Boreiko, R. T.↗
NASA NTRS1993

Measurements of the anisotropy of the cosmic background radiation at 0.5 deg scale near the star Mu Pegasi

Results are presented from the third flight of the MAX experiment, an attitude-controlled balloon-borne millimeter-wave telescope with a 0.5 deg beam, a 1 deg chop, and a three-channel bolometric photometer. Several hours of high-quality data were obtained during a flight on 1991 June 5, including long integrations to search for CBR anisotropy, two separate measurements of dust in the Galactic plane, a brief scan of the Coma Cluster to search for the Sunyaev-Zel'dovich (SZ) effect, and a number of important systematic tests. Data from one of the long CBR integrations, carried out in a region of sky near the star Mu Pegasi, are presented. The primary structure in the data is shown to be emission from Galactic dust via its spectrum and correlation with the IRAS 100/micron map. Several approaches are used to fit this dust component and remove it from the data. An upper limit to CBR anisotropy of deltaT/T less than 2.5 x 10 exp -5 is obtained for a Gaussian autocorrelation function with coherence angle omega(c) = 25'. This limit is significantly higher than the measurement sensitivity of deltaT/T about 1 x 10 exp -5 due to the presence of residual structure in the data after removal of the dust component.

Meinhold, P.↗
NASA NTRS1992

Engineering a visual system for seeing through fog

We examine the requirements for on-board aircraft sensor systems that would allow pilots to 'see through' poor weather, especially fog, and land and rollout aircraft under conditions that currently cause flight cancellations and airport closures. Three visual aspects of landing and rollout are distinguished: guidance, hazard detection and hazard recognition. The visual features which support the tasks are discussed. Three broad categories of sensor technology are examined: passive millimeter wave (PMMW), imaging radar, and passive infrared (IR). PMMW and imaging radar exhibit good weather penetration, but poor spatial and temporal resolution. Imaging radar exhibits good weather penetration, but typically relies on a flat-earth assumption which can lead to interpretive errors. PMMW systems have a narrow field of view. IR has poorer weather penetration but good spatial resolution. We recommend using both millimeter-wave and infrared sensor systems, blending the images using multiresolution digital-image pyramid-processing technology, and fusing the resulting real-time images with stored database imagery of the same scene.

Larimer, J.↗
NASA NTRS1992

Error analysis applied to several inversion techniques used for the retrieval of middle atmospheric constituents from limb-scanning MM-wave spectroscopic measurements

The formal retrieval error analysis of Rodgers (1990) allows the quantitative determination of such retrieval properties as measurement error sensitivity, resolution, and inversion bias. This technique was applied to five numerical inversion techniques and two nonlinear iterative techniques used for the retrieval of middle atmospheric constituent concentrations from limb-scanning millimeter-wave spectroscopic measurements. It is found that the iterative methods have better vertical resolution, but are slightly more sensitive to measurement error than constrained matrix methods. The iterative methods converge to the exact solution, whereas two of the matrix methods under consideration have an explicit constraint, the sensitivity of the solution to the a priori profile. Tradeoffs of these retrieval characteristics are presented.

Puliafito, E.↗
NASA NTRS1993

A degree scale anisotropy measurement of the cosmic microwave background near the star Gamma Ursae Minoris

Results from a search for anisotropy in the cosmic microwave background (CMB) are presented from the third flight of the Millimeter-wave Anisotropy experiment. The CMB observation occurred over 1.37 hours and covered a 6.24 sq deg area of the sky where very little foreground emission is expected. Significant correlated structure is observed at 6 and 9/cm. At 12/cm we place an upper limit on the structure. The relative amplitudes at 6, 9, and 12/cm are consistent with a CMB spectrum. The spectrum of the structure is inconsistent with thermal emission from known forms of interstellar dust. Synchrotron and free-free emission would both require unusually flat spectral indices at cm wavelengths in order to account for the amplitude of the observed structure. Although known systematic errors are not expected to contribute significantly to any of the three optical channels, excess sidelobe contamination cannot be definitively ruled out. If all the structure is attributed to CMB anisotropy, a value of the weighted rms of the 6 and 9/cm channels of Delta T/T(CMB) = 4.7 +/- 0.8 x 10 exp -5 (+/- 1 sigma) was measured. If the CMB anisotropy is assumed to have a Gaussian autocorrelation function with a coherence angle of 25 arcmin, then the most probable value is Delta T/T(CMB) = 4.2 +1.7 or -1.1 x 10 exp -5, where the +/- refers to the 95 percent confidence limits.

Gundersen, J. O.↗
NASA NTRS1993

Fabrication of high-quality superconductor-insulator-superconductor junctions on thin SiN membranes

We have successfully fabricated high-quality and high-current density superconductor-insulator-superconductor (SIS) junctions on freestanding thin silicon nitride (SIN) membranes. These devices can be used in a novel millimeter-wave and THz receiver system which is made using micromachining. The SIS junctions with planar antennas were fabricated first on a silicon wafer covered with a SiN membrane, the Si wafer underneath was then etched away using an anisotropic KOH etchant. The current-voltage characteristics of the SIS junctions remained unchanged after the whole process, and the junctions and the membrane survived thermal cycling.

Garcia, Edouard↗
NASA NTRS1993

Investigation of passive atmospheric sounding using millimeter and submillimeter wavelength channels

Progress by investigators at the Georgia Institute of Technology in the development of techniques for passive microwave retrieval of water vapor, cloud, and precipitation parameters using millimeter- and sub-millimeter wavelength channels is reviewed. Channels of particular interest are in the tropospheric transmission windows at 90, 166, 220, 340, and 410 GHz and centered around the water vapor lines at 183 and 325 GHz. Collectively, these channels have potential application in high-resolution mapping (e.g., from geosynchronous orbit), remote sensing of cloud and precipitation parameters, and retrieval of water vapor profiles. During the period from 1 Jan. 1993 through 30 Jun. 1993 the Millimeter-wave Imaging Radiometer (MIR) completed data flights during a two-month long deployment in conjunction with TOGA/COARE. Coincident data was collected from several other ground-based, airborne, and satellite sensors, including the NASA/MSFC AMPR, MIT MTS, DMSP SSM/T-2 satellite, collocated radiosondes, ground- and aircraft-based radiometers and cloud lidars, airborne infrared imagers, solar flux probes, and airborne cloud particle sampling probes.

Gasiewski, A. J.↗
NASA NTRS1992

Quartz/fused silica chip carriers

The primary objective of this research and development effort was to develop monolithic microwave integrated circuit (MMIC) packaging which will operate efficiently at millimeter-wave frequencies. The packages incorporated fused silica as the substrate material which was selected due to its favorable electrical properties and potential performance improvement over more conventional materials for Ka-band operation. The first step towards meeting this objective is to develop a package that meets standard mechanical and thermal requirements using fused silica and to be compatible with semiconductor devices operating up to at least 44 GHz. The second step is to modify the package design and add multilayer and multicavity capacity to allow for application specific integrated circuits (ASIC's) to control multiple phase shifters. The final step is to adapt the package design to a phased array module with integral radiating elements. The first task was a continuation of the SBIR Phase 1 work. Phase 1 identified fused silica as a viable substrate material by demonstrating various plating, machining, and adhesion properties. In Phase 2 Task 1, a package was designed and fabricated to validate these findings. Task 2 was to take the next step in packaging and fabricate a multilayer, multichip module (MCM). This package is the predecessor to the phased array module and demonstrates the ability to via fill, circuit print, laminate, and to form vertical interconnects. The final task was to build a phased array module. The radiating elements were to be incorporated into the package instead of connecting to it with wire or ribbon bonds.

Source record↗
NASA NTRS1993

Airborne imaging of tropospheric emission at millimeter and submillimeter wavelengths

In September 1993, the NASA Millimeter-wave Imaging Radiometer (MIR) flew on board the NASA ER-2 high-altitude aircraft during CAMEX, and obtained the first wideband millimeter- and submillimeter-wavelength images of tropospheric emission. The MIR is a cross-track radiometer with channels at 89, 150, 183 +/- 1, 3, 7, 220, and 325 +/- 1, 3, 8 GHz. This set provides upwelling brightness information at the two strong rotational water vapor lines at 183.310 and 325.153 GHz and three nearby atmospheric transmission windows. The wideband MIR images of convective raincells reveal unique cloud and precipitation mapping capabilities that are not available from lower frequency microwave channels. Comparisons between the 183 and 325 GHz spectra also reveal differential brightness temperature modes that are related to cloud water.

Wang, J. R.↗
NASA NTRS1993

A Monolithic W-Band Three-Stage LNA Using 0.1 Micron InAlAs/InGaAs/InP HEMT Technology

A monolithic W-band three-stage Low Noise Amplifiers (LNA) based on 0.1 um pseudomorphic InAlAs/InGaAs/InP (High Electron Mobility Transistors (HEMTs) has been developed. this LNA demonstrated a noise figure of 4.3 dB and an associated small signal gain of 19 dB at 100 GHz with a low dc power consumption of 20 mW. This is the best reported monolithic W-band LNA performance using InP-based HEMT technology and demonstrates the potential of InP HEMT technology for higher millimeter-wave applications.

Wang, H.↗