Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of temperature and dose rate on ion-irradiated γ-LiAlO 2 pellets

Defect accumulation and microstructural evolution during ion irradiation at elevated temperatures are governed by competing processes of defect production, driven by the dose rate, and defect recovery, controlled by diffusion, interaction, and annihilation. Here, this study investigates the effects of irradiation temperature and the dose rate on microstructural evolution, deuterium retention, and lithium volatilization in γ-LiAlO 2 pellets subjected to sequential He + and D + ion irradiation. Experiments were performed to a total fluence of 3 × 10 17 (He + + D + )/cm 2 at 623, 673, 723, and 773 K with an average He + dose rate of 7.7 × 10 −4 dpa/s, and to 2 × 10 17 (He + + D + )/cm 2 at 773 K with dose rates of 6.8 × 10 −5 , 2.9 × 10 −4 , and 7.3 × 10 −4 dpa/s. At 623 K, the microstructure was dominated by cavities and fractures with no observable precipitate formation, while small precipitates emerged at 673 K. Increasing the irradiation temperature to 723–773 K promoted the formation of larger, faceted LiAl 5 O 8 precipitates, and surface amorphization, accompanied by pronounced lithium depletion and H–D isotopic exchange. At 773 K, medium and high dose rates produced an amorphized surface layer over a crystalline subsurface containing LiAl 5 O 8 precipitates and blisters at the crystalline–amorphous interface, whereas low-dose-rate irradiation preserved surface crystallinity with cavities distributed in the matrix, around precipitates, and along grain boundaries. Precipitate morphology was anisotropic with limited size dependence on the dose rate. These results elucidate the coupled effects of temperature and the dose rate and demonstrate that sequential He + and D 2 + irradiation at 773 K reproduces key microstructural features and H isotope behavior observed in neutron-irradiated γ-LiAlO 2 at 573 K.

dose rate effects↗
DOE OSTI2024

Co-, Ni- and Fe-rich grain-boundary phases enhance creep resistance in θ'-strengthened Al-Cu alloys

Here, microstructural evolution and creep response were investigated in the cast Al-5.0Cu-0.3Mn-0.2Zr (wt.%) alloy with and without addition of slow-diffusing, intermetallic-forming elements Fe, Ni, or Co. Baseline Al-5.0Cu-0.3Mn-0.2Zr alloy exhibits high creep resistance at 300 °C, up to ~75 MPa, which is attributed to high-aspect-ratio, intragranular θ'-Al 2 Cu precipitates that effectively suppress dislocation climb. However, θ'-Al 2 Cu precipitate-free zones form along grain boundaries upon heat treatment, whose extent is amplified during subsequent creep. Such weak regions experience dislocation creep, leading to strain localization and acceleration of grain-boundary sliding. Adding Ni and Co, individually or in combination, leads to the formation of grain-boundary precipitates (Al 9 Co 2 , Al 3 Ni 2 ) which are resistant to coarsening, thus suppressing the formation of θ'-Al 2 Cu precipitate-free zones. This microstructure provides high creep resistance at stresses up to 75–80 MPa, with strain rates much lower than in unmodified Al-5.0Cu-0.3Mn-0.2Zr. Adding Fe, which results in extensive decoration of grain boundaries with coarsening-resistant Al 7 Cu 2 Fe, and then increasing the Cu content to compensate for the Cu loss to this new phase, leads to a new Al-7.4Cu-1.6Fe-0.3Mn-0.2Zr alloy with creep resistance at 300 °C that surpasses known cast aluminum alloys. Adding Fe to improve the creep resistance of Al-Cu alloys is both cost-effective and sustainable. Our findings offer guidelines applicable to various alloy systems on controlling the evolution of precipitate-free zones and its ensuing effects on creep deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Aperture and roughness govern iron oxide passivation in olivine fractures during carbon mineralization

Efficient carbon dioxide mineralization in silicate-rich formations depends on reaction rates within fracture networks, yet the role of fracture microstructure remains poorly constrained. We investigated how fracture aperture and surface roughness influence mineralization by reacting synthetic forsteritic olivine fractures with controlled apertures (0.5–1.6 millimeters) and roughness (6–16 micrometers) with supercritical carbon dioxide at 13.7 megapascals and 185 degrees Celsius. Optical microscopy and Raman spectroscopy showed that rougher fracture surfaces promoted iron oxide precipitation, which passivated olivine surfaces, limiting magnesium availability for carbonate formation while removing iron as a reactant. These effects were more pronounced in smaller-aperture fractures. A geochemical model incorporating surface topography and passivation reproduced the observed trends, confirming that increased roughness can reduce reactivity despite greater surface area. Our results demonstrate that fracture microstructure strongly influences iron oxide passivation and carbon dioxide mineralization, with important implications for predicting long-term performance of engineered carbon dioxide storage systems.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Boosting the use of bauxite residue (red mud) in cement - Production of an Fe-rich calciumsulfoaluminate-ferrite clinker and characterisation of the hydration

Highlights: • Incorporation of 35 wt% of bauxite residue for production of CSAF clinker • Thermochemical calculations as suitable tool for predicting phase assemblage • Hydration of the cement was found to be accelerated in contrast to other CSA cements. • High early compressive strengths of 40 MPa In the present work, calciumsulfoaluminate-ferrite clinker was produced using 35 wt% of bauxite residue in combination with alumina, clay, limestone and gypsum. At a temperature of 1300 °C, the hydraulic phases ye'elimite, ferrite and C{sub 2}S were formed. Computed thermochemical predictions were a significantly better match for the real mineralogy than modified Bogue equations. Hydration of the clinker led to the formation of ettringite and monosulfate, resulting in compressive strengths of 17 MPa after 28d. Compressive strengths of 40 MPa after 2d, and 28d-strengths exceeding 50 MPa, were reached in blends with 10 wt% of anhydrite. The strength development was due to the rapid formation of ettringite, mainly originating from ye'elimite, which did not convert to AFm phases and led to a compact microstructure. Only when the ye'elimite dissolution decreased, did the ferrite phase react. In pastes with additional sulfates, ferrite hydration led to the formation of ettringite and to hydrogarnet. Cement nomenclature is used in this work.{sup 1}.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Heterogeneous phase transformation pathways in additively manufactured Al-Ce-Mn alloys

Heat treatment of additively manufactured Al-Ce based multicomponent alloys leads to complex microstructure evolution. In this research, the ability to extend the phase transformation theories involving nucleation of a product phase from a heterogeneous multi-phase microstructure typical to that of additively manufactured samples is explored. The Al-10Ce-8Mn (wt%) was used as a model alloy system. Under additive manufacturing conditions different solidification microstructures were obtained due to spatial and temporal variations of thermal gradients (G) and liquid-solid interface velocities (R) within a given melt pool. Near the melt pool boundary (high G and low R, referred as MPB region), initially, Al 20 Mn 2 Ce forms from the liquid followed by a eutectic of FCC Al and Al 11 Ce 3 . In the melt pool interiors (low G and high R referred as ES region) a eutectic structure between FCC Al and Al 20 Mn 2 Ce is observed. During subsequent heat treatments, the MPB and ES regions transform into different sets of microstructures. In the MPB region, a fine globular microstructure containing FCC Al, Al 11 Ce 3 , Al 6 Mn, and Al 12 Mn results from the decomposition of Al 20 Mn 2 Ce. In the ES region a faceted Al 51 Mn 7 Ce 4 plate phase results from the decomposition of Al 20 Mn 2 Ce. The formation of the Al 51 Mn 7 Ce 4 phase within the eutectic microstructure at the boundaries of FCC Al and Al 20 Mn 2 Ce has not been reported in the literature. Further, these two distinct phase transformation pathways are rationalized based on the role of driving force on the nucleation of (Al 6 Mn) and/or metastable intermetallic (Al 51 Mn 7 Ce 4 ) phases at the interface of aluminum (FCC) and the non-equilibrium intermetallic (Al 20 Mn 2 Ce) phases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Surface and subsurface characterization of laser-interference structured Ti6Al4V

Ti6Al4V specimens were exposed to high-energy laser pulses of 1.24 J/cm 2 fluences per pulse using a two-beam optical configuration to attain laser-interference. In addition to the formation of periodic surface textures by laser-interference, scanning electron microscope (SEM) images demonstrated several microstructural changes on the surface processed. Moreover, the surface and subsurface of Ti6Al4V specimens were characterized for the as-received and laser-interference processed conditions using x-ray photoelectron spectroscopy (XPS) and electron energy dispersive spectroscopy (EDS). The XPS data showed that this laser technique is effective at removal of surface contaminants for Ti6Al4V. The XPS analysis also revealed the formation of an oxy-nitride layer on the laser treated material. Finally, the microstructure analysis indicates that grain refinement, dendrite and twin structures were found near the surface due to laser processing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Processing and microstructure of ZrB 2 –SiC composite prepared by reactive spark plasma sintering

In-situ formation of ZrB 2 –SiC composites was investigated by reactive spark plasma sintering of precursor powders according to the reaction B4C + 2ZrC + 3Si → 3SiC + 2ZrB 2 . The reaction and process presented here involves a diffusion reaction between B4C and ZrC which facilitates the formation of ZrB 2 , while liquid phase sintering of silicon facilitates atomic diffusion and combines with free C from the B4C and ZrC reaction to form SiC within minutes of heating and there were some residual unreacted precursor materials. An interpenetrating matrix of ZrB 2 –SiC was formed that shows increased fracture toughness (6.03 ± 0.45 MPa m 1/2 ) despite relatively low density (95 %).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cobalt-Free Cathodes for Next Generation Li-Ion Batteries

In this U.S. Department of Energy sponsored project Nexceris, in collaboration with project partners; The Ohio State University and Navitas Advanced Systems have advanced the technical maturity of a non-cobalt containing cathode for next-generation Li-ion batteries. The cathode is based on the lithium manganese nickel-titanium oxide, LiNi 0.5 Mn 1.5 TiO 4 (LNMTO) high voltage spinel. To address limitations with poor cycle and calendar life an microstucturally hierarchical LNMO/LNMTO core-shell cathode powder has been developed that enables the formation of a solid-electrolyte interface that effectively passivates the cathode surface. The microstructural enhancements of the cathode material focus on preferentially enriching the surface with titanium. In parallel, new, optimized binder and electrolyte chemistries have been incorporated to address degradation mechanisms associated with high-voltage systems. Single-layer pouch cell and large-format 2-Ah cell testing have shown that an optimized LNMO/LNMTO core-shell powder significantly improves initial cell capacity and cycle life compared to homogeneous LNMO powder. To support development and the fabrication of 2-Ah cells a novel Hybrid Alternative Wet-Chemical Synthesis (HAWCS) process have been developed. This low-cost, synthesis approach enables the excellent compositional and particle morphology control achieved with co-precipitation without the strict process controls and associated expensive process equipment.

25 ENERGY STORAGE↗
DOE OSTI2024

Manufacturing porous U-10Zr metallic fuels with controllable microstructure by volume control spark plasma sintering

In this paper, the volume control spark plasma sintering tool has been designed and applied to sinter porous U-10Zr metallic fuels, by which the sintered sample volume can be precisely controlled. Ethanol and NH 4 HCO 3 are used to control the powder compact or as pore formers to control the pore size and pore structure. Without pore formers, the fuel pellet displays an inhomogeneous microstructure consisting of highly porous and highly densified areas. Uneven powder stacking in the green body results in a non-uniform microstructure, and in the closed-packed area, Joule heating accelerates the neck formation and densification. The addition of ethanol reduces the friction between the powders, resulting in isolated pores formed by the stacking of powders during the sintering. By adding NH 4 HCO 3 , the pore size, and structure can be well controlled, and an interconnected pore structure can be obtained upon the decomposition of the NH 4 HCO 3 . Further, a uniform microstructure and pore distributions can be achieved through the U-10Zr fuel pellets by controlling current flow during the volume control SPS sintering. The microstructure and phase characterization of the sintered porous U-10Zr pellets show major phases of α-U and α-Zr for the sample with short dwelling. For the sample with long dwelling (30 min), the ω UZr 2 in the Zr-enriched area has been observed. The strategy of volume control SPS sintering with the assistance of pore formers could be used to fabricate porous U-10Zr metallic fuels to mimic the microstructure evolution of irradiated metallic fuels (including porosity) and could enable a possible solution for the design of new sodium-free metallic fuels for high burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Steam oxidation and microstructural evolution of rare earth silicate environmental barrier coatings

A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO 2 at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas the YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and Mechanical Properties of Intercritically Treated Grade 91 Steel

Premature creep failures at the intercritical heat affected zone (ICHAZ) of creep-resistant steel weldments have been frequently reported. However, the creep degradation mechanism of different microstructure constituents in ICHAZ is complicated and needs further clarification. In this work, Grade 91 steel was intercritically heat-treated at a temperature (860 °C) between the critical temperatures AC1 and AC3, and a correlation between microstructure and mechanical properties of the heat-treated specimen was built. The effects of austenitization and tempering resulting from the intercritical treatment (IT) differentiated the local strain energies between the two microstructure constituents: newly transformed martensite (NTM) and over-tempered martensite (OTM). The formation of NTM grains led to a hardness increase from 247 HV0.5 in the base metal to 332 HV0.5 in the IT specimen. The ultimate tensile strength (UTS) increased from 739 MPa in the base metal to 1054 MPa in the IT specimen. Extensive growth of the OTM grains and rapid recovery of NTM grains took place simultaneously in the IT specimen during a typical tempering at 760 °C. These microstructure degradations led to a lowered hardness of 178 HV0.5, a reduced UTS of 596 MPa, and a poor creep resistance with a minimum creep strain rate of 0.49 %/h at 650 °C in an IT + tempering (ITT) specimen.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Origin, parameters, and underlying deformation mechanisms of propagating deformation bands in irradiated 316L stainless steel

Lüders-type propagating deformation bands were observed in specimens of irradiated 316L stainless steel samples removed from Spallation Neutron Source target vessels after service. Mechanical testing with digital image correlation (DIC) and in-situ tensile testing with scanning electron microscopy electron backscatter diffraction showed that the observed Lüders-type behavior was not related to the known transformation-induced plasticity or twinning-induced plasticity behavior. Instead, the phenomenon occurs at small local strain values before a significant amount of martensite or deformation twins appear in the microstructure. Microstructural analysis and in-situ mechanical test results suggest Lüders-type band formation and propagation were related to the appearance and evolution of defect-free channels—analogous to slip bands. A modified Swift equation with a Ludwigson-like component was offered to rationalize the phenomenon and model the strain-softening processes at small strain values. Finally, the results indicate complex microstructural processes and deformation mechanisms were active at small strain values and underline the benefits of advanced mechanical test approaches such as DIC.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scaling microstructural processes in the sintering of ionic ceramics

A multi-scale framework, combining a multiphase field formulation and large deformation mechanics, was developed as a stepping stone to perform the data analytics of the microstructural level kinetics of a sintering solid. Relevant microstructural information from this framework, such as grain, stress, and porosity statistics, was scaled up to describe the macroscopic level sintering kinetics. Here, the developed formulation was applied to describe the electric field assisted sintering of Y 2 O 3 . Microstructural inhomogeneities in a multi-granular solid result in the formation of a field of compressive stress networks, which interleave with low compression and weakly tensile regions, defining a scaffolding for sintering concentration regions to develop. A Poisson effect-induced lateral stress network is also naturally self-induced as a result of the mechanical constraints imposed by the sintering apparatus. For long sintering times, localized shear stresses enhancing mass flow along grain boundaries and internal surfaces develop. Three-sided pores are removed by either vacancy transport to the surrounding pores, or move towards the external surfaces through grain boundary diffusion. Four- and higher order-sided pores stabilize because an equal amount of vacancies are gained and lost through the connecting grain boundaries. Grain dewetting contributes to pore coalescence, suggesting that pore kinetics and grain growth are coupled and should be analyzed in concert. The combined sintering and grain growth kinetics define six regimes of sintering behavior: (1) T, the transient regime; (2) E$_Υ$, the surface energy dominated, early sintering regime, where the grain growth exponent, p = 1, and the stress concentration factor, $f$ ~ $1/\hat{ρ}^{4.6}$; (3) E S , the stress dominated, early sintering regime, where p = 1 and $f$ ~ $1/\hat{ρ}^{4}$; (4) I$_Υ$, the surface energy dominated, intermediate sintering regime, where p = 2 and $f$ ~ $1/\hat{ρ}^{4.6}$; (5) I S , the stress dominated, intermediate sintering regime, where p = 2 and $f$ ~ $1/\hat{ρ}^{4}$; and (6) L, the late sintering regime, where p = 3 and $f$ ~ 1. At the macroscopic level, the rapid densification and suppression of grain growth observed in the electric field assisted sintering process is a consequence of the compounding effects of the underlying stress-, transport-, and interfacial-energy-induced energy minimization kinetics, as predicted by the multi-scale framework.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Microstructural and phase changes in alpha uranium investigated via in-situ studies and molecular dynamics

A deeper knowledge of thermally induced microstructural and phase evolution in nuclear metallic fuel can be obtained using novel in-situ microscopic analyses. Such studies can provide information on the dynamics of phase transitions which is not possible with conventional postmortem characterization (post-irradiation examination). In this work, the behavior of alpha uranium (α-U) was investigated via in-situ heating tests in a transmission electron microscope. Here, the main objective is to understand the microstructural and phase changes, such as defect annihilation and ß phase formation and retention, observed in reactor in-pile transient studies at the Transient Reactor Test facility. Indeed, defect migration and rearrangement were observed within the α phase starting at 673 K; α→ß phase transition was observed between 773 K and 1,073 K during the heating ramp (which is in the temperature window reported for α→ß transition temperatures). Recrystallization and formation of nano grains was observed at high temperatures (over 1,073 K). Such recrystallization was possibly related to the formation of the γ phase. Finally, it was indeed observed that the ß phase (but not γ phase) was retained at room temperature upon rapid cooling. Molecular dynamics studies support these experimental results and shows that the γ phase of pure uranium cannot be retained at room temperature if not stabilized with the addition of an alloying element.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Dynamics of Radiation Damage Buildup in Ultrathin Hexagonal Boron Nitride Films under Ion Bombardment

Two-dimensional hexagonal boron nitride (hBN) is attractive for several emerging applications. Ion bombardment can be used to modify the hBN properties. However, the understanding of radiation damage buildup in hBN remains limited. Here, we investigate the effects of the dose rate and ion mass on radiation damage buildup by studying 40 nm-thick hBN films bombarded at room temperature with 500 keV 4 He, 15 N, 40 Ar, and 129 Xe ions and comparing with results for ion bombardment of polycrystalline hBN ceramics. Raman spectroscopy is used to quantify damage buildup, and transmission electron microscopy is used for microstructural analysis. Experiments are complemented by molecular dynamics simulations of the formation and evolution of point defects. Lighter ions are found to be more efficient at disordering hBN than heavier ions. This observation points to a critical role of intracascade defect processes. In contrast, a negligible dose rate effect observed suggests limited intercascade defect dynamic annealing processes for these irradiation conditions. These findings provide a fundamental basis for hBN defect engineering.

2D materials↗
DOE OSTI2025

Microstructure and bonding between calcium aluminate cement‐containing gahnite–alumina matrix and refractory aggregates

Calcium aluminate cement enhances the thermomechanical properties of refractory castables through the formation of acicular calcium hexaluminate (CaO·6Al 2 O 3 ), Ca 2 Mg 2 Al 28 O 46 (CAM-I), and CaMg 2 Al 16 O 27 (CAM-II) phases in MgO- or MgAl 2 O 4 -containing castables. The compatibility of CA 6 with gahnite (ZnAl 2 O 4 ), and acicular Ca 2 Zn 2 Al 28 O 46 (CAZ-I) and CaZn 2 Al 16 O 27 (CAZ-II) phases formation have been previously reported. Here, in this work, the interaction between a CAC binder containing ZnAl 2 O 4 -Al 2 O 3 matrix with commonly used refractory aggregates such as tabular alumina (TA), alumina-rich (AR90, AR78) and stoichiometric (SM72) MgAl 2 O 4 spinels, and fused and dead-burned magnesia (FM, DBM, respectively) were investigated at 1650°C for 5 h. Microstructural analysis, using digital microscopy, scanning electron microscopy, and energy dispersive spectroscopy, revealed the formation of acicular CaZn 0.18 Al 11.82 O 18.91 , CAZ-I and CAZ-II grains, and strong interfacial bonding between the matrix and TA and spinel aggregates. FM and DBM were found to debond from the matrix. Thick interface layers were observed between the matrix and all the aggregates but TA. Null hypothesis significance testing (NHST) shows that the difference in the number of acicular grains between the interface zone and the bulk matrix (Z) is statistically significant for AR90/Z, SM72/Z, FM/Z, and DBM/Z interfaces, but not significant for TA/Z and AR78/Z. The role of the aggregates’ chemistry on the interfacial bonding and microstructure evolution is discussed.

Ramteke, Rajat Durgesh [Univ. of Alabama, Birmingh↗
DOE OSTI2022

High-Energy Solid-State Lithium Batteries with Organic Cathode Materials (Final Report)

Organic materials made from abundant elements via low-energy processes are emerging as sustainable and low-cost alternatives to transition metal oxides as the electrode materials for high- energy batteries in the wake of supply chain and environmental issues associated with critical materials during the transition to clean energy. Organic insertion materials (OIMs) offer material- level energy comparable to transition metal oxides, but they have durability difficulties owing to dissolving in common liquid electrolytes. Combining ceramic-based solid electrolytes with organic electrode materials is one intriguing solution. The goal of this project is to design and synthesize high-energy OIMs, to understand the chemical dynamics and mechanical properties at the OIM-sulfide interface during electrochemical cycling, and to develop methods for constructing the optimum cathode microstructure, which will lead to improved electrochemical performance. The project team has accomplished the following over the last four years: (a) demonstrating that the mechanical softness of organic electrode materials is uniquely beneficial in suppressing crack formation at the electrode-electrolyte interface during cell operation; (b) understanding the interaction between cathode microstructure and the mechanical properties of individual components; and (c) establishing predictive control of cathode microstructure by tuning the mechanical properties of solid electrolytes and OIMs; (d) determining the chemical combability of sulfide electrolyte with high-energy OIMs and finally (f) laying out a road map toward a specific energy of 500 Wh kg -1 for solid-state lithium batteries. 14 publications resulted from this project.

25 ENERGY STORAGE↗
DOE OSTI2025

Microstructurally informed synchrotron x-ray analysis revealing helium defect transitions in ultrafine grained tungsten

The formation of insoluble gaseous defects in materials due to nuclear transmutation or ion implantation involves the diffusion of impurity atoms to form atomic defect clusters that coalesce into bubbles or cavities and ultimately degrade the material properties. Transmission electron microscopy (TEM) is limited in its ability to resolve sub-nanometer gas clusters whereas X-ray diffraction (XRD) provides information pertaining to local atomic changes. Here, in this study, helium (He) implanted ultrafine grained tungsten is explored through a multimodal defect characterization campaign combining TEM-informed Small Angle X-ray Scattering (SAXS) analysis, XRD lattice parameter measurements, and nanoscale He cluster quantification from a region of reciprocal space accessible via Wide Angle X-ray Scattering (WAXS). Moderate elevated temperature implantations are shown to produce high concentrations of sub-nanoscale He clusters and small, homogeneously distributed cavities, which collectively are linked to lattice expansion and further substantiated through complementary atomistic simulations. Increased implantation temperatures encourage the diffusion of these defects to the grain boundaries (GBs), leading to lattice relaxation and the growth of large GB cavities manifesting as bimodal size distributions in the SAXS analysis. Overall, our results demonstrate the utility of multimodal synchrotron X-ray analysis in bridging the gap between microscale He cavity quantification and atomic-scale defect analysis.

36 MATERIALS SCIENCE↗