Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MORTARS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Concentration profiles of tritium penetrated into concrete

Concentration profiles of tritium in cement paste, mortar and concrete were measured after exposure to tritiated water vapor for a given time. Tritium penetrated a distance of about 5 cm from the exposed surface during an exposure of 6 months. The model of tritium behavior in concrete materials reported by the present authors was developed in this study with the consideration of the effects of sand and aggregate on both the diffusion coefficient of tritiated water vapor and the isotope exchange capacity. Predictive calculations based on the tritium transport model were also carried out in some situations of tritium leakage. The results of the calculations show that a large amount of tritium will be trapped in the concrete walls, and the trapped tritium will be gradually released back to the tritium handling room over the time of months to years even after the decontamination of the room is completed. (authors)

36 MATERIALS SCIENCE↗

A hybrid pore‐scale and continuum‐scale model for solute diffusion, reaction, and biofilm development in porous media

Abstract It is a challenge to upscale solute transport in porous media for multispecies bio‐kinetic reactions because of incomplete mixing within the elementary volume and because biofilm growth can change porosity and affect pore‐scale flow and diffusion. To address this challenge, we present a hybrid model that couples pore‐scale subdomains to continuum‐scale subdomains. While the pore‐scale subdomains involving significant biofilm growth and reaction are simulated using pore‐scale equations, the other subdomains are simulated using continuum‐scale equations to save computational time. The pore‐scale and continuum‐scale subdomains are coupled using a mortar method to ensure continuity of solute concentration and flux at the interfaces. We present results for a simplified two‐dimensional system, neglect advection, and use dual Monod kinetics for solute utilization and biofilm growth. The results based on the hybrid model are consistent with the results based on a pore‐scale model for three test cases that cover a wide range of Damköhler (Da = reaction rate/diffusion rate) numbers for both homogeneous (spatially periodic) and heterogeneous pore structures. We compare results from the hybrid method with an upscaled continuum model and show that the latter is valid only for cases of small Damköhler numbers, consistent with other results reported in the literature.

Tang, Youneng↗

Evading strength and ductility trade-off in an inverse nacre structured magnesium matrix nanocomposite

Mimicking nacre structure is an often-used strategy for developing materials which combine high strength and high toughness. Here, a novel strategy, named inverse nacre structure, is proposed where elongated and curled soft constituents are embedded in a matrix of hard constituent to form an ordered brick-and-mortar arrangement. This strategy is demonstrated in a particle reinforced metal matrix composite, using pure Mg as the soft phase and SiC nanoparticle reinforced Mg as the hard phase. In this work, the resulting nanocomposite yields high strength, and especially high tensile elongation which is five times that of the homogeneous counterpart. The superior comprehensive strengthening-toughening effect originates from the tailored inverse nacre structure which enables a stable microcrack-multiplication process by sufficiently promoting strain hardening so as to avoid any significant decrease in post-ultimate tensile strength. This strategy, while demonstrated here for the specific case of particle reinforced Mg, is not restricted to any particular material system but constitutes a generic pathway for the development of high-performance materials for engineering applications.

36 MATERIALS SCIENCE↗

Discrimination of phosgene from cyanogen chloride in recovered chemical munitions using tagged neutron interrogation with high-resolution gamma-ray spectroscopy

The Associated Particle technique has recently been utilized with a germanium-based high-resolution $\gamma$-ray spectrometer and assessed for its capability to improve field identification of recovered chemical warfare (CW) materiel through prompt gamma-ray neutron activation analysis (PGNAA) measurements. An accurate chemical identification is necessary for the safe handling, destruction, and disposal of such hazardous items. A particularly challenging pair of CW agents commonly found in recovered munitions are phosgene (CG) and cyanogen chloride (CK), which have two of three elements in common, i.e. chlorine and carbon, but differ in the third being either oxygen or nitrogen. The detection of both latter elements is complicated by high oxygen concentration in the field environment which interferes with the small signal produced from the chemical agents. The matter is further complicated by the precautionary field practice of overpacking recovered munitions with vermiculite in larger steel multiple round containers (MRCs), which places additional oxygen-rich material around the munition while further attenuating an already weak signal emitted from the munition center. Here, this work reports quantitative results from realistic field measurements of CG and CK simulants in mock 4.2-inch mortar rounds overpacked with vermiculite in a large MRC. Results obtained with the AP technique are compared to those obtained with the traditional PGNAA approach for both overpacked- and bare-munition measurements. The AP technique is shown to provide a much more confident discrimination between the two chemicals, particularly for the more challenging field-relevant overpacked measurements, where a significant gain in sensitivity to all the key elements chlorine, carbon, nitrogen and oxygen is achieved.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Calcium nitrate: A chemical admixture to inhibit aggregate dissolution and mitigate expansion caused by alkali-silica reaction

Alkali-silica reaction (ASR) is a significant cause of the degradation of concrete structures. ASR results from the dissolution of reactive silicate aggregates and the subsequent formation of damaging, expansive ASR gels. Despite the prevalence of ASR, so far only lithium-based chemical admixtures have been shown to be successful in mitigating its deleterious effects. Herein, dissolved calcium nitrate (Ca(NO 3 ) 2 : CN) is demonstrated to reduce ASR-induced expansion caused by the use of sodium borosilicate (NBS) glass as a model reactive aggregate. The significance of reductions of NBS-glass dissolution and mortar-bar expansion rates is discussed, with special focus on highlighting the mechanism by which calcium nitrate mitigates ASR, i.e., by the inhibition of aggregate dissolution. This study reveals a new and cost-effective pathway to suppress aggregate dissolution and ASR in concrete based on the dosage of soluble alkaline-earth additives.

36 MATERIALS SCIENCE↗

{sup 1}H NMR relaxometry as an indicator of setting and water depletion during cement hydration

Proton nuclear magnetic resonance relaxometry has been used to detect setting and microstructure evolution during cement hydration. NMR measurements were performed since casting, during setting and until hardening (from 0 to 3 days). The mobility of water molecules was assessed by an analysis focused on the diagram of longitudinal relaxation time T{sub 1} generated by an Inversion Recovery sequence. The initial stiffening of the solid network was identified by an analysis of the relaxation rate 1/T{sub 1}. The kinetics of water depletion was investigated by using a simple one-pulse acquisition sequence. In parallel, conventional techniques (Vicat needle and temperature monitoring), as well as numerical simulations of hydration, were used to complement and validate these NMR results. Cement pastes and mortars with different water-to-cement ratios made of grey or white OPCs were tested. Furthermore, the effects of the addition of sand, super-plasticizer and silica fume on the hydration kinetics were investigated.

36 MATERIALS SCIENCE↗

Sulfate attack expansion mechanisms

A specially constructed stress cell was used to measure the stress generated in thin-walled Portland cement mortar cylinders caused by external sulfate attack. The effects of sulfate concentration of the storage solution and C{sub 3}A content of the cement were studied. Changes in mineralogical composition and pore size distribution were investigated by X-ray diffraction and mercury intrusion porosimetry, respectively. Damage is due to the formation of ettringite in small pores (10–50 nm) which generates stresses up to 8 MPa exceeding the tensile strength of the binder matrix. Higher sulfate concentrations and C{sub 3}A contents result in higher stresses. The results can be understood in terms of the effect of crystal surface energy and size on supersaturation and crystal growth pressure.

36 MATERIALS SCIENCE↗

Internal curing with lightweight aggregate produced from biomass-derived waste

Shrinkage of concrete may lead to cracking and ultimately to a reduction of the service life of concrete structures. Among known methods for shrinkage mitigation, internal curing with porous aggregates was successfully utilized in the last couple of decades for decreasing autogenous and drying shrinkage. In this paper, the internal curing performance of pre-saturated lightweight aggregates produced from biomass-derived waste (bio-LWA) was studied. In the first part of this paper, the microstructure of the bio-LWA is investigated, with special focus on their pore structure and on their water absorption and desorption behavior. The bio-LWA has large porosity and coarse pore structure, which allows them to release the entrained water at early age and counteract self-desiccation and autogenous shrinkage. In the second part, the efficiency of internal curing in mortars incorporating the bio-LWA is examined by neutron tomography, internal relative humidity and autogenous deformation measurements.

36 MATERIALS SCIENCE↗

Sorption of radionuclides by cement-based barrier materials

This paper investigates the sorption of radionuclide ions, {sup 137}Cs{sup +} and {sup 90}Sr{sup 2+}, by cement-based barrier materials for radioactive waste disposal. A mortar with ternary binder is prepared and powder samples are ground from the hardened material following a predetermined granulometry. After pre-equilibrium with an artificial pore solution, the sorption behaviors of powder samples are investigated through single sorption and blended sorption. The results show that: (1) no systematic difference is observed for single and blended sorptions thus the interaction between {sup 137}Cs{sup +} and {sup 90}Sr{sup 2+} sorptions must be weak; (2) the sorption kinetics is rapid and all characteristic times are less than 1d; (3) the sorption capacity is enhanced by C–A–S–H hydrates and the measured K{sub d} values can be predicted from C–S–H sorption data with Ca/Si ratio equal to Ca/(Si + Al) ratio.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Early age strength increase of fly ash blended cement by a ternary hardening accelerating admixture

The applicability of a combination of sodium thiocyanate (NaSCN), diethanolamine (DEA) and glycerol (Gly) with small dosages as a ternary hardening accelerating admixture for fly ash blended cement (OPC-FA) was studied. The ternary admixture induced higher early and later age mortar strength at both low (5 °C) and normal (20 °C) temperature. Despite used in lower dosage the ternary admixture led to higher strength of the investigated OPC-FA system than other chemicals (e.g. sodium sulfate). Results obtained from isothermal calorimetry, thermogravimetric analysis (TGA) and X-ray diffraction (XRD) showed that the ternary admixture accelerated the cement hydration and increased the amount of AFm (notably calcium hemicarboaluminate hydrate) in the hydration products. A synergistic effect between the three components of the accelerator on the hydration of OPC-FA system was observed.

36 MATERIALS SCIENCE↗

Mapping high pH levels in hydrated calcium silicates

Data on the variability of pH levels in cement-based materials is essential for a better understanding of the early aging of materials and the long-term performance of concrete structures. Current approaches for measuring pH levels in concrete are inadequate with respect to radiometric range and resolution and spatial granularity. We report on a methodology for mapping pH levels in concrete utilizing a halochromic porphyrin sensor molecule that allows a simple measurement of surface values of pH level using a commercial digital camera setup. As proof of concept, cement paste, mortar, and concrete samples were subject to accelerated carbonation and then evaluated for pH profiles at different ages of degradation. Comparative tests on the same specimens were also conducted using phenolphthalein as the pH indicator. Spatial distribution of pH level from pH 11.0 to 13.5 was mapped at various levels of carbonation.

36 MATERIALS SCIENCE↗

Predictive modelling of hydration and mechanical performance of low Ca composite cements: Possibilities and limitations from industrial perspective

We quantified hydration and performance development of composites cements containing metakaolin in the rage of 0–40% and investigated applicability of thermodynamic and micromechanical models to predict the evolution of hydrates assemblage and of performance, respectively. The reaction of metakaolin results in a formation of significant amounts of C-S-H phase for lower metakaolin content and of strätlingite for higher contents. This leads to very dense matrix with finer porosity allowing co-existence of thermodynamically incompatible phases, namely portlandite and strätlingite. Hence, thermodynamic modelling cannot be applied to correctly predict the phase assemblage for the systems with high metakaolin content. By introducing constraints into the thermodynamic model in a form of minimum phase content, the XRD-amorphous phases can be quantified. However, such constraints are only valid for the cases studied and limit the general applicability and predictive power of the model. Elastic properties and strength of mortars are influenced by the metakaolin additions in an opposite trend. It indicates that they are sensitive to different microstructural features/mechanisms. Continuum micromechanic-based model is capable to accurately predict the performance evolution based on the volume of hydrates predicted by the thermodynamic modelling. An additional step required for the accurate prediction - porosity is partitioned based on its saturation at 95% RH – is introduced and substantiated.

36 MATERIALS SCIENCE↗

Water and chloride ions migration in porous cementitious materials: An experimental and molecular dynamics investigation

The interactions of water and chloride ions penetration into porous mortar have been investigated experimentally and modelled by molecular dynamics. The water distribution visualized by neutron radiography and chloride penetration by Electron Probe Micro-Analysis indicate that separation of chloride ions from water during the penetration process took place and water ran much deeper into the material than chloride ions. The relationship between the penetration depth of water and chloride ions can be described by a linear function despite different water-cement ratio. Furthermore, molecular dynamics attributes the different transport mechanisms of water and ions in porous cementitious materials to three reasons: the nanostructure of hydration product play filtering role to screen chloride ions with larger hydration shell; as compared with water, ions reside in the calcium silicate surface for longer time due to the strong interfacial bonding; chloride ions accumulate and form CaCl ionic cluster, slowing down the migrating rate.

36 MATERIALS SCIENCE↗

The composition and performance of alite-ye'elimite clinker produced at 1300 °C

Alite-ye'elimite clinker is a high cementing clinker prepared by introducing calcium sulfoaluminate, a non-silicate mineral, into the cement clinker. The mineral composition and mechanics of tricalcium silicate-rich sulfur aluminate prepared at 1300 °C are reported. The effects of copper slag and phosphorus slag on the phase composition, heat release and compressive strength were investigated. The phase composition was analysed by X-ray powder diffraction. The results show that the copper slag and phosphorus slag can lower the burn temperature of the clinker and promote the coexistence of C{sub 3}S and C{sub 4}A{sub 3} S-bar . The quality of clinker produced at 1300 °C is satisfactory. The compressive strength of mortar curing at 28 d is higher than that of P·II 52.5.

36 MATERIALS SCIENCE↗

Pozzolanic reactivity of natural pozzolans, ground glasses and coal bottom ashes and implication of their incorporation on the chloride permeability of concrete

It is well understood that the partial replacement of portland cement with pozzolans in sufficient proportions results in improved long-term performance of concrete. However, dwindling availability of the most widely used pozzolan in the construction industry, fly ash, is forecast due to the termination of coal-fired electricity power stations around the world, necessitating the exploration of alternative pozzolans. Experimental investigations are conducted to study the performance of traditional pozzolans such as fly ash, silica fume and natural pozzolans (metakaolin, pumice, perlite and lassenite) together with novel pozzolans, including ground glasses (high-alkali and low-alkali), and ground bottom ash. Twenty-one concrete mixtures are examined for compressive strength, electrical conductivity, electrical resistivity, chloride permeability, and chloride migration coefficient. The reactivity of pozzolans studied is also determined in terms of compressive strength in lime-pozzolan mortar using a modified lime-reactivity test method. Many of the materials tested demonstrate the potential to be used in place of fly ash. However, a wide variation in the performance of these materials is evident which highlights the need for a reliable test to determine the level of reactivity of a pozzolan. The results indicate that the 7-day strength in the modified lime-reactivity test provides a good indication of the pozzolanic reactivity of the material and of how the material can be expected to contribute to the strength and permeability of concrete. The use of electrical resistivity as an indicator of the performance of pozzolans in terms of strength development and chloride penetration resistance when used to partially replace portland cement in concrete is also discussed.

36 MATERIALS SCIENCE↗

3D imaging techniques for characterising microcracks in cement-based materials

Concrete inherently contains pores and microcracks that can adversely impact its mechanical properties and long-term durability. However, characterising microcracks is difficult due to their complex, multiscale and three-dimensional (3D) nature. This paper presents an evaluation of 3D imaging techniques for characterising microcracks induced by different mechanisms. Seven cement pastes, mortars and concretes subjected to drying shrinkage, autogenous shrinkage and freeze-thaw cycles were investigated using focused ion beam nanotomography (FIB-nt), broad ion beam serial section tomography (BIB-SST), laser scanning confocal microscopy (LSCM) combined with serial sectioning and X-ray microtomography (μCT). The study shows that the characteristics of microcracks vary significantly depending on exposure conditions. Yet there is no single technique that can capture the entire size range of microcracks from sub to tens of μm within a sufficiently representative sampling volume. The achievable image volume and resolution, and the advantages and disadvantages of each technique are compared and discussed.

36 MATERIALS SCIENCE↗

Sulfate performance of blended cements (limestone and illite calcined clay) exposed to aggressive environment after casting

This paper evaluates how early aggressive exposure affects the sulfate resistance of blended cements containing limestone filler and/or calcined clay. Mortar and cement paste specimens were elaborated with different combinations of limestone filler and two different illitic calcined clays and exposed to a sodium sulfate solution shortly after casting. Assessment of sulfate resistance was based on expansion, mass variation, and compressive strength. Microscale evolution and distribution were examined by mercury intrusion porosimetry, X-ray diffraction, and scanning electron microscopy with energy-dispersive spectrometry measurements. Results prove superior sulfate resistance of compositions with high calcined clay content over limestone filler addition. Furthermore, the results reported suggest that the pozzolanic reaction progresses enough to reduce the sulfate ingress even at early exposure conditions. Therefore, calcined clay replacement can still provide effective pore refinement to limit sulfate penetration, increase strength, and reduce available CH to limit expansive phase formation.

36 MATERIALS SCIENCE↗