Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAXED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Thermal-mechanical fatigue crack growth in Inconel X-750

Thermal-mechanical fatigue crack growth (TMFCG) was studied in a gamma-gamma' nickel base superalloy Inconel X-750 under controlled load amplitude in the temperature range from 300 to 650 C. In-phase (T sub max at sigma sub max), out-of-phase (T sub min at sigma sub max), and isothermal tests at 650 C were performed on single-edge notch bars under fully reversed cyclic conditions. A dc electrical potential method was used to measure crack length. The electrical potential response obtained for each cycle of a given wave form and R value yields information on crack closure and crack extension per cycle. The macroscopic crack growth rates are reported as a function of delta k and the relative magnitude of the TMFCG are discussed in the light of the potential drop information and of the fractographic observations.

Marchand, N.↗
NASA NTRS1986

The solar maximum satellite capture cell: Impact features and orbital debris and micrometeoritic projectile materials

The physical properties of impact features observed in the Solar Max main electronics box (MEB) thermal blanket generally suggest an origin by hypervelocity impact. The chemistry of micrometeorite material suggests that a wide variety of projectile materials have survived impact with retention of varying degrees of pristinity. Impact features that contain only spacecraft paint particles are on average smaller than impact features caused by micrometeorite impacts. In case both types of materials co-occur, it is belevied that the impact feature, generally a penetration hole, was caused by a micrometeorite projectile. The typically smaller paint particles were able to penetrate though the hole in the first layer and deposit in the spray pattern on the second layer. It is suggested that paint particles have arrived with a wide range of velocities relative to the Solar Max satellite. Orbiting paint particles are an important fraction of materials in the near-Earth environment. In general, the data from the Solar Max studies are a good calibration for the design of capture cells to be flown in space and on board Space Station. The data also suggest that development of multiple layer capture cells in which the projectile may retain a large degree of pristinity is a feasible goal.

Mckay, D. S.↗
NASA NTRS1985

Thermal-mechanical fatigue crack growth in Inconel X-750

Thermal-mechanical fatigue crack growth (TMFCG) was studied in a 'gamma-gamma' nickel base superalloy Inconel X-750 under controlled load amplitude in the temperature range from 300 to 650 C. In-phase (T sub max at sigma sub max), out-of-phase (T sub min at sigma sub max), and isothermal tests at 650 C were performed on single-edge notch bars under fully reversed cyclic conditions. A dc electrical potential method was used to measure crack length. The electrical potential response obtained for each cycle of a given wave form and R value yields information on crack closure and crack extension per cycle. The macroscopic crack growth rates are reported as a function of delta k and the relative magnitude of the TMFCG are discussed in the light of the potential drop information and of the fractographic observations.

Marchand, N.↗
NASA NTRS1988

Isothermal and bithermal thermomechanical fatigue behavior of a NiCoCrAlY-coated single crystal superalloy

Specimens of single crystal PWA 1480 with group of zone axes (100) orientation, bare, or with NiCoCrAlY coating PWA 276, were tested in low cycle fatigue (LCF) at 650, 870, and 1050 C, and in simplified bithermal thermomechanical fatigue (TMF) tests between these temperatures. These tests were examined as a bridge between isothermal LCF and general TMF. In the bithermal test, an inelastic strain is applied at one temperature, T sub max, and reversed at T sub min. The out-of-phase (OP) test type imposing tension at T sub min and compression at T sub max received most study, since it was more damaging than the in-phase type. Specifically investigated were the effects of: inelastic strain range, the coating, delta T, T sub max, T sub min, and the environment.

Gayda, J.↗
NASA NTRS1988

On the relationship between optical polarization and extinction

A sample of stars including lines of sight within various dense clouds and stars in the diffuse interstellar medium are examined in order to investigate the relationship between various color ratios and the wavelength of the maximum of the interstellar polarization, lambda(max). The correlation of Serkowski (1975) is confirmed. The extinction laws have been fitted by minimizing the square deviations from the observed colors and the derived law. The results suggest that variations in lambda(max) are caused by differences in particle size distributions. Stars with large lambda(max) are noted in the outer regions of dense clouds, regions which are probably disturbed.

Clayton, Geoffrey C.↗
NASA NTRS1988

Isothermal and 'bithermal' thermomechanical fatigue behavior of a NiCoCrAlY-coated single crystal superalloy

Specimens of single crystal PWA 1480 with group of zone axes (100) orientation, bare, or with NiCoCrAlY coating PWA 276, were tested in low cycle fatigue (LCF) at 650, 870, and 1050 C, and in simplified bithermal thermomechanical fatigue (TMF) tests between these temperatures. These tests were examined as a bridge between isothermal LCF and general TMF. In the bithermal test, and inelastic strain is applied at one temperature, T sub max, and reversed at T sub min. The out-of-phase (OP) test type imposing tension at T sub min and compression at T sub max received most study, since it was more damaging than the in-phase type. Specifically investigated were the effects of: inelastic strain range, the coating, delta T, T sub max, T sub min, and the environment.

Gayda, J.↗
NASA NTRS1990

Additive evaluation criteria for aircraft noise

The occurrence of unexpected aircraft noise events will frequently evoke intense complaints about annoyance over such events. It is recognized that the relationship between the volume of complaints and the corresponding maximum noise levels does in fact depend on the circumstances of the complainants and the time of year. The frequency of occurrence of the respective noise events is also a factor. The possible practical value of the addition of the maximal noise level, to the well-known cumulative noise descriptors L(sub eq), L(sub dn), etc. may be considered. One might start by considering the difference between the L(sub eq) and the average maximal noise level of the twenty loudest single noise events on an average day. A somewhat less sharply focused consideration of the maximum noise levels was adopted. In that standard the scope of noise-mitigation measures is defined generally with reference to L(sub eq). If the average maximal noise level L(sub max) of the entire aircraft fleet mix exceeds the L(sub eq) by more than 20 dB(A) and if more than 20 daily aircraft noise events exceed the L(sub eq) than the difference L(sub max)-20 becomes the key criterion for noise-mitigation measures. A statistical correlation of a large number of data from aircraft-noise-monitoring sensors located both directly underneath and laterally disposed to an aircraft flight-path has supplied a basis for the determination of the distribution of the maximal noise levels about the average value, L(sub max), of each type of aircraft. This distribution is given for the takeoff climb and for the landing approach.

Meyer, Thomas J.↗
NASA NTRS1989

Effects of simulated weightlessness and sympathectomy on maximum VO2 of male rats

The effects of simulated weightlessness (hind-limb suspension) and chemical sympathectomy (by repeated injections with guanethidine sulfate) on the maximum oxygen consumption (VO2 max) of female rats were investigated in rats assigned for 14 days to one of three groups: a head-down hind-limb suspension, a horizontal suspension with hind limbs weight bearing, or the caged control. The VO2 max values were assessed by having rats run on a treadmill enclosed in an airtight chamber. The hind-limb-suspended sympathectomized rats were found to exhibit shorter run times and lower mechanical efficiencies, compared to their presuspension values or the values from saline-injected suspended controls. On the other hand, the suspended sympathectomized rats did not demonstrate a decrease in the VO2 max values that was observed in saline-injected controls.

Woodman, C. R.↗
NASA NTRS1991

Range optimization for a supersonic aircraft

Range optimal trajectories for an aircraft flying in the vertical plane are obtained from Pontryagin's Minimum Principle. Control variables are load factor n which appears nonlinearly in the equations of motion and throttle setting eta, which appears only linearly. Both controls are subject to fixed bounds, namely eta between values of 0 and 1 and absolute value of n not greater than n(max). Additionally, a dynamic pressure limit is imposed, which represents a first-order state-inequality constraint. For fixed flight time, fixed initial coordinates, and partially fixed final coordinates, the effect of the load factor limit absolute value of n not greater than n(max) is studied. Upon varying n(max), six different switching structures are obtained. All trajectories involve singular control along arcs with active dynamic pressure limit.

Seywald, Hans↗
NASA NTRS1991

A statistical analysis of gamma-ray bursts detected by the Konus Experiment on Venera 11 and 12

We discuss the advantages of using the V/V sub max method to test well-defined samples of gamma-ray bursts for the spatial uniformity of their parent population. We have applied the V/V sub max test to gamma ray bursts of duration longer than 1 second recorded by the Konus experiment aboard Venera 11 and 12. Based on a sample of 123 bursts, we find V/V sub max equals 0.46 plus or minus 0.03, consistent with a uniform distribution in space. We urge that experimenters give careful attention to the detection limit for each recorded gamma ray burst, and that quantitative data for burst properties and detection limits be published.

Schmidt, Maarten↗
NASA NTRS1991

Instantaneous heat transfer coefficient based upon two-dimensional analyses of Stirling space engine components

Twelve different cases of multidimensional models of Stirling engine components for space applications have been numerically investigated for oscillating, incompressible laminar flow with heat transfer. The cases studied covered wide ranges of Valensi number (from 44 to 700), Re(max) number (from 8250 to 60,000), and relative amplitude of fluid motion of 0.686 and 1.32. The Nusselt numbers obtained from the present study indicate a very complex shape with respect to time and axial location in the channel. The results indicate that three parameters can be used to define the local Nusselt number variation, namely: time average, amplitude, and phase angle. These parameters could be correlated respectively using: Re(max), Va and Re(max), and the relative amplitude of fluid motion.

Ibrahim, Mounir↗
NASA NTRS1992

A study of subterahertz HEMT monolithic oscillators

A detailed study of monolithic InP-based HEMT oscillators for subterahertz operation is presented. InAlAs/InGaAs HEMT's have been optimized for high frequency operation and showed very high maximum oscillation frequencies (f(sub max)) of 310 GHz using offset self-aligned gamma-gate technology. Power characteristics of HEMT oscillators are reported. An oscillation power of more than 10 mW was evaluated by large-signal analysis at 320 GHz using HEMT's with f(sub max) = 450 GHz, V(sub br) = 10 V and a gate width (W(sub g)) of 8 x 22.5 microns. Oscillator topology studies showed that complex feedback schemes such as dual and active feedback enhance the negative resistance. Push-push oscillator designs based on harmonic signal generation can finally be used to overcome the frequency barrier imposed by f(sub max).

Kwon, Youngwoo↗
NASA NTRS1953

Investigation at supersonic speeds of the variation with Reynolds number and Mach number of the total, base, and skin-friction drag of seven boattail bodies of revolution designed for minimum wave drag

An investigation has been conducted in the Langley 9-inch supersonic tunnel to determine the effect of the variation with Reynolds number and Mach number of the total, base, and skin-friction drag at zero lift of seven boattail bodies of revolution designed for minimum wave drag according to NACA TN 2550. The tests covered a Reynolds number range from approximately 1.0 x 10(6) to 10.0 x 10(6) at Mach numbers of 1.62, 1.93, and 2.41, respectively. The results show that base drag and, in general, the total drag increase with increasing values of the ratio of base area to maximum area B/S(sub max), although the results reported in NACA TN 3054 showed that the wave drag decreased with increasing values of B/S(sub max). The laminar skin-friction drag is in agreement with the theoretical predictions used, and, within the Mach number range of these tests, the simple Blasius incompressible theory gives a satisfactory prediction. Except for values of B/S (sub max) near 1, the Reynolds number of transition increases with increasing Mach number and as this ratio approaches 1 this variation is seen to reverse. These variations in Reynolds number of transition with Mach number appear to be associated with the changes in pressure gradient over the rear of the bodies.

Bromm, August F , Jr↗
NASA NTRS1994

Surface Fatigue Life of High Temperature Gear Materials

Three high temperature gear materials were evaluated using spur gear surface fatigue tests. These materials were, VASCO max 350, VASCO matrix 2, and nitralloy N and were evaluated for possible use in high temperature gear applications. The fatigue life of the three high temperature gear materials were compared with the life of the standard AISI 9310 aircraft gear material. Surface fatigue tests were conducted at a lubricant inlet temperature of 321 K (120 F), a lubricant outlet temperature of 350 K (170 F), a maximum Hertz stress of 1.71 GPa (248 ksi), a speed of 10,000 rpm, and with a synthetic paraffinic lubricant. The life of the nitralloy N was approximately the same as the AISI 9310, the life of the VASCO max 350 was much less than the AISI 9310 while the life of the VASCO matrix 2 was several times the life of the AISI 9310. The VASCO max 350 also showed very low fracture toughness with approximately half of the gears failed by tooth fracture through the fatigue spall. The VASCO matrix 2 had approximately 10-percent fracture failure through the fatigue spalls indicating moderate to good fracture toughness.

Townsend, Dennis P.↗
NASA NTRS1994

The ground vehicle manager's associate

An overview of MAX, a software framework for manager's associate systems, is presented. MAX is used to develop and execute a problem-solving strategy for the task planning of semi-autonomous agents with the assistance of human performance. This paper describes the use of MAX in the supervisory management of robotic vehicles as they explore a planetary surface.

Edwards, Gary R.↗
NASA NTRS1994

An algorithm for solving the system-level problem in multilevel optimization

A multilevel optimization approach which is applicable to nonhierarchic coupled systems is presented. The approach includes a general treatment of design (or behavior) constraints and coupling constraints at the discipline level through the use of norms. Three different types of norms are examined: the max norm, the Kreisselmeier-Steinhauser (KS) norm, and the 1(sub p) norm. The max norm is recommended. The approach is demonstrated on a class of hub frame structures which simulate multidisciplinary systems. The max norm is shown to produce system-level constraint functions which are non-smooth. A cutting-plane algorithm is presented which adequately deals with the resulting corners in the constraint functions. The algorithm is tested on hub frames with increasing number of members (which simulate disciplines), and the results are summarized.

Balling, R. J.↗
NASA NTRS1993

Some requirements of a colliding comet source of gamma ray bursts

Colliding comets in the Solar System may be an important source of gamma ray bursts. The spherical gamma ray comet cloud required by the results of the Venera Satellites (Mazets and Golenetskii, 1987) and the Burst and Transient Source Experiment (BATSE) detector on the Compton Satellite (Meegan et al., 1992a, b) is neither the Oort Cloud nor the Kuiper Belt. To satisfy observations of N(greater than P(sub max)) vs P(sub max) for the maximum gamma ray fluxes, P(sub max) greater than 10(exp -5) ergs/sq cm/ s (about 30 bursts/yr), the comet density, n, should increase as n approximately a(exp 1) from about 40 to 100 AU where a is the comet heliocentric distance. The turnover above 100 AU requires n approximately a(exp -1/2) to 200 AU to fit the Venera results and n approximately a(exp 1/4) to 400 AU to fit the BATSE data. Then the masses of comets in the 3 regions are from: 40-100 AU, about 9 earth masses, m(sub E); 100-200 AU about 25 m(sub E); and 100-400 AU, about 900 m(sub E). The flux of 10(exp -5) ergs/sq cm/s corresponds to a luminosity at 100 AU of 3 x 10(exp 26) ergs/s. Two colliding spherical comets at a distance of 100 AU, each with nucleus of radius R of 5 km, density of 0.5 g/cu cm and Keplerian velocity 3 km/s have a combined kinetic energy of 3 x 10(exp 28) erg, a factor of about 100 greater tha required by the burst maximum fluxes that last for one second.

White, R. Stephen↗
NASA NTRS1960

Investigation at Mach Numbers of 0.20 to 3.50 of Blended Wing-Body Combinations of Sonic Design with Diamond, Delta, and Arrow Plan Forms

The models had aspect-ratio-2 diamond, delta, and arrow wings with the leading edges swept 45.00 deg, 59.04 deg, and 70.82 deg, respectively. The wing sections were computed by varying the section shape along with the body radii (blending process) to match the prescribed area distribution and wing plan form. The wing sections had an average value of maximum thickness ratio of about 4 percent of the local chords in a streamwise direction. The models were tested with transition fixed at Reynolds numbers of about 4,000,000 to 9,000,0000, based on the mean aerodynamic chord of the wings. The effect of varying Reynolds number was checked at both subsonic and supersonic speeds. The diamond model was superior to the other plan forms at transonic speeds ((L/D)max = 11.00 to 9.52) because of its higher lift-curve slope and near optimum wave drag due to the blending process. For the wing thickness tested with the diamond model, the marked body and wing contouring required for transonic conditions resulted in a large wave-drag penalty at the higher supersonic Mach numbers where the leading and trailing edges of the wing were supersonic. Because of the low sweep of the trailing edge of the delta model, this configuration was less adaptable to the blending process. Removing a body bump prescribed by the Mach number 1.00 design resulted in a good supersonic design. This delta model with 10 percent less volume was superior to the other plan forms at Mach numbers of 1.55 to 2.35 ((L/D)max = 8.65 to 7.24), but it and the arrow model were equally good at Mach numbers of 2.50 to 3.50 ((L/D)max - 6.85 to O.39). At transonic speeds the arrow model was inferior because of the reduced lift-curve slope associated with its increased sweep and also because of the wing base drag. The wing base-drag coefficients of the arrow model based on the wing planform area decreased from a peak value of 0.0029 at Mach number 1.55 to 0.0003 at Mach number 3.50. Linear supersonic theory was satisfactory for predicting the aerodynamic trends at Mach numbers from 1.55 to 3.50 of lift-curve slope, wave drag, drag due to lift, aerodynamic-center location, and maximum lift-drag ratios for each of the models.

Holdaway, George H.↗