Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Effects of helium on irradiation response of reduced-activation ferritic-martensitic steels: Using nickel isotopes to simulate fusion neutron response

Understanding the effects of helium on microstructures and mechanical properties of reduced-activation ferritic-martensitic steels is important to use of these steels in fusion reactor structures. The 9Cr-2WVTa steels were doped with 58Ni and 60Ni isotopes at 2 weight percent to control the rate of transmutation helium generation. The samples were irradiated in the High Flux Isotope Reactor to ~24 displacements per atom at nominal temperatures of 300, 400, and 500°C, producing 228 and 7 atomic parts-per-million helium in the 58 Ni- and 60 Ni-doped samples, respectively. Transmission electron microscopy revealed a variety of precipitates and the radiation-induced dislocation loops and cavities (voids or helium bubbles). Tensile tests of the irradiated samples at the irradiation temperatures showed radiation-induced hardening at 300°C and radiation-induced softening at 400°C. Analysis indicates that the hardening primarily originated from the loops and cavities. The 58 Ni-doped samples had greater strengthening contributions from loops and cavities, leading to higher hardening with lower ductility than the 60 Ni-doped samples. The greater helium production of 58 Ni did not show pronounced reductions in ductility of the samples.

36 MATERIALS SCIENCE↗

Microstructures and mechanical properties of a modified 9Cr ferritic-martensitic steel in the as-built condition after additive manufacturing

A newly developed nano-structured high-Mn 9Cr ferritic-martensitic (FM) steel designed for additive manufacturing (Additive-manufactured Nanostructured Alloy, ANA) was fabricated via the direct energy deposition method. The as-printed ANA2 showed tensile properties (strength and elongation) and Charpy impact toughness (upper-shelf energy and ductile-brittle transition temperature) comparable to oxide-dispersion-strengthened (ODS) Eurofer and PM2000. Compared with wrought P91, the as-built ANA2 showed significantly higher yield strength but inferior Charpy impact toughness and ductility. Microstructural characterization revealed uniformly distributed sub-micron pores, an extremely high dislocation density, and a high density of ultrafine nano-structured precipitates in the matrix. The microstructures indicated the dislocations as the dominant strengthening element and the ultrafine precipitates as the primary contribution to estimated irradiation sink density. This work demonstrates the ability to exploit the unique consolidation properties of additive manufacturing to fabricate steels which marry the benefits of both ODS alloys and conventionally processed FM steels.

36 MATERIALS SCIENCE↗

The Role of Co-injected Helium on Swelling and Cavity Evolution at High Damage Levels in Ferritic-Martensitic Steels

The influence of helium co-injection at rates from 0 to 4 appm He/dpa on swelling in ferritic-martensitic alloys T91 and HT9 was explored. Irradiations with 5.0 MeV Fe++ ions and degraded He++ ions were performed at 445°C up to damage levels of 150 dpa and helium co-injection rates of 0, 0.02, 0.2 and 4 appm He/dpa in T91, and at 460°C to a damage level of 188 dpa and helium co-injection rates of 0, 0.06 and 4 appm He/dpa in HT9. Helium was observed to enhance cavity nucleation at low damage levels, resulting in the maximum swelling at the highest helium co-injection rate. As the damage level was increased, the helium content at which swelling was maximized shifted to lower helium concentrations, ultimately resulting in the highest swelling occurring with zero helium by 150 dpa. Finally, this behavior was due to the helium-stabilized bubble microstructure that increased the cavity sink strength and reduced both cavity growth rate and swelling relative to the helium-free condition.

36 MATERIALS SCIENCE↗

Under the microscope: Reduced activation ferritic martensitic steel Eurofer-97 following ion-Irradiation and high-temperature high-pressure water exposure

Here, this study is designed to characterise the microstructural behaviour of Eurofer-97 steel under ion irradiation and subsequent exposure to high-temperature high-pressure (HTHP) water. Eurofer-97, a ferritic-martensitic steel, has been developed to withstand the conditions of fusion reactors in the locations in contact with coolant with an elevated level of neutron flux, such as the breeder-wall blanket. The material has been studied after self-ion irradiation (using Fe ions) simulating the microstructural effects of neutron irradiation limited to the subsurface layer. The corrosion properties of the Eurofer-97 steel were studied by exposure to HTHP water up to 331 °C. Advanced microstructural characterisation using scanning, transmission electron and focused ion beam microscopy was performed on the as-received microstructure and after ion irradiation. This was then characterised after exposure for 240 h in high-temperature water. Eurofer-97 had a dense, columnar Cr-rich inner oxide, followed by a Fe-rich outer oxide layer. In the irradiated condition the grain structure and oxide itself was less ordered. No appreciable difference in oxide thickness was identified between the irradiated and unirradiated specimens after this short exposure time.

36 MATERIALS SCIENCE↗

High-temperature nanoindentation creep studies on castable and sintered nanostructured low-activation ferritic-martensitic alloys

In this article, we present the creep characteristics of two reduced activation ferritic-martensitic steels of identical starting compositions formed by different fabrication routes: a nanostructured ferritic alloy commonly referred to as a castable nanostructured alloy (CNA) and a sintered nanostructured alloy (SNA) variant. Through a series of nanoindentation experiments spanning a temperature range of 25 °C to 650 °C, with a maximum load of 100 mN, we find creep behaviors in the cast and sintered materials to be remarkably similar. The creep stress exponent (n) for CNA and SNA were found to be in the range of 8–35 and the activation volume was ∼14–42b 3 , underscoring a dominance of dislocation-mediated mechanisms in both alloys. Notably, we observed a decline in the creep stress exponent with increasing temperature, attributable to the heightened influence of thermally activated dislocations. This phenomenon suggests a potential transition in the deformation mechanism towards a thermally activated dislocation climb process, significantly impacting the observed creep behavior.

36 MATERIALS SCIENCE↗

The shape recovery conditions for Fe–Mn–Si alloys: An interplay between martensitic transformation and plasticity

Highlights: • Fe15Mn5Si9Cr5Ni samples were rolled at 800 °C and annealed at 650 (C1) and 1000 °C (C2). • TEM analysis was performed. • High density of stacking faults and appropriate density of dislocation appears in C1. • Complex dislocation arrays due to plastic deformation are observed in C2. • Shape memory properties depend on the thermomechanical treatment. - Abstract: This work analyses the improvement of the shape memory properties of Fe-Mn-Si based alloys, and expands upon and deepens recently published developments concerning this topic. We prepared TEM specimens from a Fe-15Mn-5Si-9Cr-5Ni sheet rolled at 800 °C and annealed at 650 °C–92% shape recovery – and from another sheet annealed at 1000 °C–45% shape recovery. Here, we analyse the development of microstructure during the γ ↔ ε martensitic transformation and correlate it with the shape memory behaviour. Among the observed microstructural features, the introduction of complex dislocation arrays due to plastic deformation appears to be critical for shape memory development, since they can arrest the backward movement of Shockley partial dislocations over the original path. Tailoring the microstructure in order to introduce a high stacking-fault density accompanied by an appropriate dislocation density remains a key issue in the design of these kinds of functional materials.

36 MATERIALS SCIENCE↗

Characterization of martensite-austenite constituents and micro-hardness in intercritical reheated and coarse-grained heat affected zones of API X70 HSLA steel

Highlights: • The influence of cold wire addition to the tandem submerged arc welding process on the ICRCGHAZ is investigated. • Comprehensive characterization of the microstructure and micro-hardness in the ICRCGHAZ of a HSLA steel is performed. • A lower fraction of finely distributed M-A formed in the ICRCGHAZ of TSAW + cold wire steel, leading to lower micro-hardness. • The aspect ratio and inter-particle spacing of M-A constituents decreased in the ICRCGHAZ through cold wire addition. - Abstract: The thermal cycles that high strength low alloy (HSLA) low carbon steels experience during welding inevitably affect the microstructure and mechanical properties of the weld joints. It is generally agreed that the coarse-grained heat affected zone (CGHAZ) and the intercritical reheated coarse-grained heat affected zone (ICRCGHAZ) in one-pass and multi-pass welding, respectively, have the poorest microstructure and mechanical properties relative to the rest of the steel joint. The martensite-austenite (M-A) constituents formed in the HAZ regions predominantly govern property deterioration in the CGHAZ and the ICRCGHAZ by promoting the initiation and propagation of micro-cracks. However, the characteristics of the M-A constituents, i.e., fraction, size, shape and aspect ratio, are strongly affected by the welding heat input. Accordingly, in this study, the aim was to evaluate the influence of a cold wire addition in conventional tandem submerged arc welding (TSAW + cold-wire) on the microstructure and micro-hardness in the CGHAZ and ICRCGHAZ. Microstructural characterization showed that a lower fraction of finely distributed M-A constituents associated with smaller prior austenite grains (PAGs) formed in the CGHAZ of the steel welded by the TSAW + cold-wire process (CW-OD weld) relative to that welded by the conventional TSAW process (TW-OD weld). Furthermore, the fraction of M-A constituents in the ICRCGHAZ of the CW-OD weld was decreased. A higher fraction of slender shaped M-A constituents in the ICRCGHAZ of the TW-OD weld resulted in an increase in the micro-hardness. The microstructure and micro-hardness changes associated with cold wire addition were attributed to the lower welding heat input and, consequently, the faster cooling rate with a corresponding reduction in the retention time in the austenitic region and ferrite/austenite region in the CGHAZ and ICRCGHAZ regions, respectively.

36 MATERIALS SCIENCE↗

Comparison of void swelling of ferritic-martensitic and ferritic HT9 alloys after high-dose self-ion irradiation

In this work, ferritic-martensitic (F/M) HT9 along with fully ferritic HT9 specimens were irradiated using self-ions to 600 peak displacement-per-atom (dpa) at 450 °C. To investigate and minimize the carbon contamination effect on void swelling, two identical F/M HT9 specimens were prepared: one without a coating and the other one with a tungsten and silver coating on the surface prior to irradiation. The specimen without a coating showed carbide formation in the matrix, resulting from carbon contamination during irradiation, with no voids observed. The coated sample did not form matrix carbides, and voids were observed within the irradiated region. The same coating was applied to the ferritic HT9, and void swelling results of both the F/M HT9 and the ferritic HT9 alloys were compared after irradiation. The F/M HT9 exhibited a maximum of 2.6% swelling, while the ferritic HT9 showed a maximum of 0.8% swelling at a 400–500 nm depth, equivalent to 334 local dpa. The results were correlated with the instability of carbides in the ferritic HT9 under irradiation. Carbides in the F/M HT9 and the ferritic HT9 are both M23C6, but the matrix carbides in the ferritic HT9 were less stable under the irradiation, compared to the ones on the grain boundaries in the F/M HT9. The study shows the impact of chemistry on the void swelling which overpowers the microstructural factors such as grain size and phase.

36 MATERIALS SCIENCE↗

Investigation of the fatigue crack behavior of 304 stainless steels using synchrotron X-ray tomography and diffraction: Influence of the martensite fraction and role of inclusions

Here, the effect of fatigue on the microstructure of four-point bend specimens of three variations of 304 stainless steels (Commercial 304, 304H, and 304 L) was investigated using synchrotron x-ray tomography and diffraction. X-ray tomography revealed the formation of the fatigue-induced microvoids and crack while the diffraction data was used to quantify the amount of deformation-induced martensite found after fatigue in all samples. Transmission electron microscopy evidenced the role of the precipitates/inclusions on the microvoid formation. It was found to depend on their chemical nature. The shape of the precipitates/inclusions was also found to have an effect on the microvoid shape.

304 stainless steel↗

Compositional analysis on the reverted austenite and tempered martensite in a Ti-stabilized supermartensitic stainless steel: Segregation, partitioning and carbide precipitation

We present that controlling the amount of reverted austenite at room temperature allows for tailoring of mechanical properties in supermartensitic stainless steels. The austenite reversion and stabilization occurs during inter-critical tempering through partitioning of austenite-stabilizing elements. The degree of partitioning greatly depends on the reversion temperature, which dictates the local equilibrium conditions. Atom probe tomography and energy dispersive spectroscopy in transmission electron microscopy were used to study the austenite reversion mechanism in terms of the elemental distribution of austenite-stabilizing, ferrite-stabilizing and carbide forming elements. Synchrotron X-ray diffraction confirmed that the austenite equilibrium phase fraction was reached after 2.5 h of isothermal reversion at 625 °C, allowing for direct comparison with thermodynamic and kinetic calculations. However, such soaking time was not enough to produce compositional homogenization in the reverted austenite. The austenite reversion and stabilization mechanism was related mainly to strong partitioning of Ni. Negligible partitioning of Cr, Mo, Si and Ti were observed. Instead, these elements were strongly segregated at the reverted austenite/martensite interfaces. Carbon and Ti played a secondary role in the austenite stabilization through the precipitation of nano-sized Ti (C,N) with partial substitution of Ti by Mo. Finally, virtually carbon-free austenite and martensite were observed away from the interfaces and precipitates.

36 MATERIALS SCIENCE↗

Martensitic transformation behaviors of rapidly solidified Ti–Ni–Mo powders

For the fabrication of bulk near-net-shape shape memory alloys and porous metallic biomaterials, consolidation of Ti–Ni–Mo alloy powders is more useful than that of elemental powders of Ti, Ni and Mo. Ti{sub 50}Ni{sub 49.9}Mo{sub 0.1} shape memory alloy powders were prepared by gas atomization, and transformation temperatures and microstructures of those powders were investigated as a function of powder size. XRD analysis showed that the B2–R–B19 martensitic transformation occurred in powders smaller than 150 μm. According to DSC analysis of the as-atomized powders, the B2–R transformation temperature (T{sub R}) of the 25–50 μm powders was 18.4 °C. The T{sub R} decreased with increasing powder size, however, the difference in T{sub R} between 25–50 μm powders and 100–150 μm powders is only 1 °C. Evaluation of powder microstructures was based on SEM examination of the surface and the polished and etched powder cross sections and the typical images of the rapidly solidified powders showed cellular morphology. Porous cylindrical foams of 10 mm diameter and 1.5 mm length were fabricated by spark plasma sintering (SPS) at 800 °C and 5 MPa. Finally these porous TiNi alloy samples are heat-treated for 1 h at 850 °C, and then quenched in ice water. The bulk samples have 23% porosity and 4.6 g/cm{sup 3} density and their T{sub R} is 17.8 °C.

36 MATERIALS SCIENCE↗

Microstructure and martensitic transformation in Si-coated TiNi powders prepared by ball milling

Graphical abstract: - Highlights: • Amorphous Si-coated TiNi powders were prepared successfully by ball milling. • Ti{sub 4}Ni{sub 4}Si{sub 7} was formed at the interface between Si and TiNi after annealing. • Si-coated Ti–Ni powders displayed the R phase after annealing. - Abstract: Si was coated on the surface of Ti–49Ni (at%) alloy powders by ball milling in order to improve the electrochemical properties of the Si electrodes of secondary Li ion batteries and then the microstructure and martensitic transformation behavior were investigated by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Ti–Ni powders coated with Si were fabricated successfully by ball milling. As-milled powders consisted of highly deformed Ti–Ni powders with the B2 phase and amorphous Si layers. The thickness of the Si layer coated on the surface of the Ti–Ni powders increased from 3–5 μm to 10–15 μm by extending the milling time from 3 h to 48 h. However, severe contamination from the grinding media, ZrO{sub 2} occurred when the ball milling time was as long as 48 h. By heating as-milled powders to various temperatures in the range of 673–873 K, the highly deformed Ti–Ni powders were recovered and Ti{sub 4}Ni{sub 4}Si{sub 7} was formed. Two-stage B2–R–B19′ transformation occurred when as-milled Si-coated Ti–49Ni alloy powders were heated to temperatures below 873 K, above this temperature one-stage B2–B19′ transformation occurred.

36 MATERIALS SCIENCE↗

Microstructural stability of tantalum-alloyed ferritic-martensitic steel with neutron irradiation to 7.4 dpa at ~490 °C

Specimens of a reduced-activation ferritic-martensitic steel, called CNA1, were irradiated to 7.4 displacements per atom at ~490 °C in the High Flux Isotope Reactor. Vickers hardness and tensile properties revealed consistent softening that is attributed to some recovery during irradiation, with reduced laths and dislocation density. Detailed microstructural characterization by transmission electron microscopy and energy dispersive x-ray spectroscopy showed radiation-induced dislocation loops, few cavities, and slight dissolution of M 23 C 6 and MX precipitates. Partial amorphization was only observed in M 23 C 6 precipitated in matrix. Transmutation somewhat destabilized M 23 C 6 and MX, with a stronger effect on the later one by noticeable depletion of Ta with enriched W, which is consistent with the transmutation calculations. The microstructural evolution and associated strength changes were discussed with the assistance of computational thermodynamics.

36 MATERIALS SCIENCE↗

Creep behavior of pack cementation aluminide coatings on Grade 91 ferritic martensitic alloy

The creep behavior of various pack cementation aluminide coatings on Grade 91 ferritic-martensitic steel was investigated at 650 C in laboratory air. The coatings were fabricated in two temperature regimes, i.e., 650 or 700 C (low temperature) and 1050 C(high temperature), and consisted of a range of Al levels and thicknesses. For comparison, uncoated specimens heat-treated at 1050 C to simulate the high temperature coating cycle also were included in the creep test. All coated specimens showed a reduction in creep resistance, with 16 51% decrease in rupture life compared to the as-received bare substrate alloy. However, the specimens heat-treated at 1050 C exhibited the lowest creep resistance among all tested samples, with a surprisingly short rupture time of < 25 h, much shorter than the specimen coated at 1050 C. Factors responsible for the reduction in creep resistance of both coated and heat-treated specimens were discussed.

Bates, Brian↗

Developing an interatomic potential for martensitic phase transformations in zirconium by machine learning

Abstract Atomic simulations provide an effective means to understand the underlying physics of structural phase transformations. However, this remains a challenge for certain allotropic metals due to the failure of classical interatomic potentials to represent the multitude of bonding. Based on machine-learning (ML) techniques, we develop a hybrid method in which interatomic potentials describing martensitic transformations can be learned with a high degree of fidelity from ab initio molecular dynamics simulations (AIMD). Using zirconium as a model system, for which an adequate semiempirical potential describing the phase transformation process is lacking, we demonstrate the feasibility and effectiveness of our approach. Specifically, the ML-AIMD interatomic potential correctly captures the energetics and structural transformation properties of zirconium as compared to experimental and density-functional data for phonons, elastic constants, as well as stacking fault energies. Molecular dynamics simulations successfully reproduce the transformation mechanisms and reasonably map out the pressure–temperature phase diagram of zirconium.

Zong, Hongxiang↗

A machine learning aided interpretable model for rupture strength prediction in Fe-based martensitic and austenitic alloys

Abstract The class of 9–12% Cr ferritic-martensitic alloys (FMA) and austenitic stainless steels have received considerable attention due to their numerous applications in high temperature power generation industries. To design high strength steels with prolonged service life requires a thorough understanding of the long-term properties, e.g., creep rupture strength, rupture life, etc., as a function of the chemical composition and processing parameters that govern the microstructural characteristics. In this article, the creep rupture strength of both 9–12% Cr FMA and austenitic stainless steel has been parameterized using curated experimental datasets with a gradient boosting machine. The trained model has been cross validated against unseen test data and achieved high predictive performance in terms of correlation coefficient ( $$R^{2} > 0.98 $$ R 2 > 0.98 for 9–12% Cr FMA and $$R^{2} > 0.95 $$ R 2 > 0.95 for austenitic stainless steel) thus bypassing the need for additional comprehensive tensile test campaigns or physical theoretical calculations. Furthermore, the feature importance has been computed using the Shapley value analysis to understand the complex interplay of different features.

36 MATERIALS SCIENCE↗

Stress-induced martensitic transformation during tensile test of full-size TF conductor jacket tube at 4.2 K

The toroidal-field (TF) conductor jacket of International Thermonuclear Experimental Reactor (ITER) is made of modified 316LN stainless steel, which is influenced by heat treatment at approximately 650 °C for 200 h to produce Nb{sub 3}Sn superconducting materials at the final stage. Due to the high electromagnetic forces arising during magnet operation, higher mechanical properties of the jacket materials at cryogenic temperatures are required. In our work, mechanical properties of the full-size TF conductor jacket tube were investigated, which satisfied the ITER requirements. Stress-induced martensitic transformation mechanism during tensile test of the conductor jacket material at 4.2 K was characterized by means of in-situ temperature dependent XRD, vibrating sample magnetometer (VSM) and in conjunction with transmission electron microscopy (TEM). The tensile behavior related to the amount of stress-induced phase transformation at cryogenic temperature was also discussed.

36 MATERIALS SCIENCE↗

A room temperature exchange bias effect caused by the coexisting martensitic phase structures in Ni50Mn38Sb12−xGax polycrystalline Heusler alloys

The exchange bias effect is the physical cornerstone of applications, such as spin valves, ultra-high-density data storage, and magnetic tunnel junctions. This work studied the room temperature exchange bias effect by constructing a Ni50Mn38Sb12−xGax alloy system with coexisting martensitic phase structures. The study found that the exchange bias effect shows a non-monotonic change with the variation of Ga composition at 300 K, and an obvious room temperature exchange bias effect appears in the alloys with coexisting phase structures of 4O and L10, which is due to the strong exchange coupling between ferromagnetic and antiferromagnetic. Further research on the exchange bias effect and temperature shows that the blocking temperature is 420 K, and the exchange bias can stably exist in a temperature range of ∼200 K around room temperature. This work provides a method to engineer exchange bias effects at room temperature.

Physics↗