Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Electronic-grade GaN(0001)/Al{sub 2}O{sub 3}(0001) grown by reactive DC-magnetron sputter epitaxy using a liquid Ga target

Electronic-grade GaN (0001) epilayers have been grown directly on Al{sub 2}O{sub 3} (0001) substrates by reactive direct-current-magnetron sputter epitaxy (MSE) using a liquid Ga sputtering target in an Ar/N{sub 2} atmosphere. The as-grown GaN epitaxial films exhibit low threading dislocation density on the order of {<=}10{sup 10} cm{sup -2} determined by transmission electron microscopy and modified Williamson-Hall plot. X-ray rocking curve shows narrow full-width at half maximum (FWHM) of 1054 arc sec of the 0002 reflection. A sharp 4 K photoluminescence peak at 3.474 eV with a FWHM of 6.3 meV is attributed to intrinsic GaN band edge emission. The high structural and optical qualities indicate that MSE-grown GaN epilayers can be used for fabricating high-performance devices without the need of any buffer layer.

36 MATERIALS SCIENCE↗

Influence of high power impulse magnetron sputtering plasma ionization on the microstructure of TiN thin films

HIPIMS (High Power Impulse Magnetron Sputtering) discharge is a new PVD technology for the deposition of high-quality thin films. The deposition flux contains a high degree of metal ionization and nitrogen dissociation. The microstructure of HIPIMS-deposited nitride films is denser compared to conventional sputter technologies. However, the mechanisms acting on the microstructure, texture and properties have not been discussed in detail so far. In this study, the growth of TiN by HIPIMS of Ti in mixed Ar and N{sub 2} atmosphere has been investigated. Varying degrees of metal ionization and nitrogen dissociation were produced by increasing the peak discharge current (I{sub d}) from 5 to 30 A. The average power was maintained constant by adjusting the frequency. Mass spectrometry measurements of the deposition flux revealed a high content of ionized film-forming species, such as Ti{sup 1+}, Ti{sup 2+} and atomic nitrogen N{sup 1+}. Ti{sup 1+} ions with energies up to 50 eV were detected during the pulse with reducing energy in the pulse-off times. Langmuir probe measurements showed that the peak plasma density during the pulse was 3 x 10{sup 16} m{sup -3}. Plasma density, and ion flux ratios of N{sup 1+}: N{sub 2}{sup 1+} and Ti{sup 1+}: Ti{sup 0} increased linearly with peak current. The ratios exceeded 1 at 30 A. TiN films deposited by HIPIMS were analyzed by X-ray diffraction, and transmission electron microscopy. At high I{sub d}, N{sup 1+}: N{sub 2}{sup 1+} > 1 and Ti{sup 1+}: Ti{sup 0} > 1 were produced; a strong 002 texture was present and column boundaries in the films were atomically tight. As I{sub d} reduced and N{sup 1+}: N{sub 2}{sup 1+} and Ti{sup 1+}: Ti{sup 0} dropped below 1, the film texture switched to strong 111 with a dense structure. At very low I{sub d}, porosity between columns developed. The effects of the significant activation of the deposition flux observed in the HIPIMS discharge on the film texture, microstructure, morphology and properties are discussed.

36 MATERIALS SCIENCE↗

Nitrogen self-diffusion in magnetron sputtered Si-C-N films

Self-diffusion was studied in magnetron sputtered nitrogen-rich amorphous compounds of the system Si-C-N by using nitrogen as a model tracer. As shown by infra-red spectroscopy a transient metastable region exists, where the structure of the material can be visualized as silicon nitride tetrahedra which are connected by carbo-diimide (-N=C=N-) bonds to a three dimensional amorphous network. In this region diffusion studies are carried out by neutron reflectometry and isotope multilayers as a function of annealing time, temperature and chemical composition. Low diffusivities between 10{sup -20} and 10{sup -24} m{sup 2}/s were found. In the metastable region, diffusion is faster than diffusion in amorphous silicon nitride by 1 to 2 orders of magnitude, while the activation enthalpies of diffusion between 3.1 and 3.4 eV are the same within error limits. This can be explained by the fact that the diffusion mechanism along SiN{sub 4} tetrahedra is identical to that in amorphous silicon nitride, however, the carbo-diimide bonds seem to widen the structure, allowing faster diffusion. A correlation between diffusivities and the number of carbo-diimid bonds present in the material is found, where the highest diffusivities are observed for materials with the highest number of carbo-diimid bonds, close to the composition Si{sub 2}CN{sub 4}.

36 MATERIALS SCIENCE↗

Measurement Of Hydrogen Capacities And Stability In Thin Films Of AlH Deposited By Magnetron Sputtering

Thin, hydrogenated aluminum hydride films were deposited on silicon substrates using unbalanced magnetron (UBM) sputtering of a high purity aluminum target under electrically grounded conditions. Argon was used as sputtering gas and hydrogenation was carried out by diluting the growth plasma with hydrogen. The effect of hydrogen partial pressure on the final concentration of trapped elements including hydrogen has been studied using ion beam analysis (IBA) techniques. Moreover, in-situ thermal stability of trapped hydrogen in the film was carried out using Rutherford Backscattering Spectrometry (RBS), Non-Rutherford Backscattering Spectrometry (NRBS) and Elastic Recoil Detection Analysis (ERDA). Microstructure of the film was investigated by SEM analysis. Hydrogen content in the thin films was found decreasing as the films were heated above 110 deg. C in vacuum.

36 MATERIALS SCIENCE↗

Elemental distribution and oxygen deficiency of magnetron sputtered indium tin oxide films

The atomic structure and composition of noninterfacial ITO and ITO-Si interfaces were studied with transmission electron microscopy and x-ray photoelectron spectroscopy (XPS). The films were deposited by dc magnetron sputtering on monocrystalline p-type (100) Si wafers. Both as deposited and heat treated films consisted of crystalline ITO. The ITO/Si interface showed a more complicated composition. A thin layer of SiO{sub x} was found at the ITO/Si interface together with In and Sn nanoclusters, as well as highly oxygen deficient regions, as observed by XPS. High energy electron exposure of this area crystallized the In nanoclusters and at the same time increased the SiO{sub x} interface layer thickness.

36 MATERIALS SCIENCE↗

Hall mobility of cuprous oxide thin films deposited by reactive direct-current magnetron sputtering

Cuprous oxide (Cu{sub 2}O) is a promising earth-abundant semiconductor for photovoltaic applications. We report Hall mobilities of polycrystalline Cu{sub 2}O thin films deposited by reactive dc magnetron sputtering. High substrate growth temperature enhances film grain structure and Hall mobility. Temperature-dependent Hall mobilities measured on these films are comparable to monocrystalline Cu{sub 2}O at temperatures above 250 K, reaching 62 cm{sup 2}/V s at room temperature. At lower temperatures, the Hall mobility appears limited by carrier scattering from ionized centers. These observations indicate that sputtered Cu{sub 2}O films at high substrate growth temperature may be suitable for thin-film photovoltaic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Reactive magnetron sputtering of Cu{sub 2}O: Dependence on oxygen pressure and interface formation with indium tin oxide

Thin films of copper oxides were prepared by reactive magnetron sputtering and structural, morphological, chemical, and electronic properties were analyzed using x-ray diffraction, atomic force microscopy, in situ photoelectron spectroscopy, and electrical resistance measurements. The deposition conditions for preparation of Cu(I)-oxide (Cu{sub 2}O) are identified. In addition, the interface formation between Cu{sub 2}O and Sn-doped In{sub 2}O{sub 3} (ITO) was studied by stepwise deposition of Cu{sub 2}O onto ITO and vice versa. A type II (staggered) band alignment with a valence band offset {Delta}E{sub VB} 2.1-2.6 eV depending on interface preparation is observed. The band alignment explains the nonrectifying behavior of p-Cu{sub 2}O/n-ITO junctions, which have been investigated for thin film solar cells.

36 MATERIALS SCIENCE↗

Hollow target magnetron-sputter-type solid material ion source

A thin-walled aluminum (Al) hollow electrode has been inserted into an ion source to serve as an electrode for a radio frequency magnetron discharge. The produced plasma stabilized by argon (Ar) gas sputters the Al electrode to form a beam of Al{sup +} and Ar{sup +} ions. The total beam current extracted through a 3 mm diameter extraction hole has been 50 {mu}A, with the Al{sup +} ion beam occupying 30% of the total beam current.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Drifting localization of ionization runaway: Unraveling the nature of anomalous transport in high power impulse magnetron sputtering

The plasma over a magnetron's erosion ''racetrack'' is not azimuthally uniform but concentrated in distinct dense ionization zones which move in the ExB direction with about 10% of the electron ExB/B{sup 2} drift velocity. The ionization zones are investigated with a gated camera working in concert with a streak camera for Al, Nb, Cu, and W targets in Ar or Kr background gas. It is found that each ionization zone has a high plasma density edge, which is the origin of a plasma-generating electron jet leaving the target zone. Each region of strong azimuthal plasma density gradient generates an azimuthal electric field, which promotes the escape of magnetized electrons and the formation of electron jets and plasma flares. The phenomena are proposed to be caused by an ionization instability where each dense plasma zone exhibits a high stopping power for drifting high energy electrons, thereby enhancing itself.

36 MATERIALS SCIENCE↗

Enhanced electrical and noise properties of nanocomposite vanadium oxide thin films by reactive pulsed-dc magnetron sputtering

Thin films of VO{sub x} (1.3 {<=} x {<=} 2) were deposited by reactive pulsed-dc magnetron sputtering of a vanadium metal target while RF-biasing the substrate. Rutherford back scattering, glancing angle x-ray, and cross-sectional transmission electron microscopy measurements revealed the formation of nanocolumns with nanotwins within VO{sub x} samples. The resistivity of nanotwinned VO{sub x} films ranged from 4 m{Omega}{center_dot}cm to 0.6 {Omega}{center_dot}cm and corresponding temperature coefficient of resistance between -0.1% and -2.6% per K, respectively. The 1/f electrical noise was analyzed in these VO{sub x} samples using the Hooge-Vandamme relation. These VO{sub x} films are comparable or surpass commercial VO{sub x} films deposited by ion beam sputtering.

36 MATERIALS SCIENCE↗

Investigating the role of hydrogen in silicon deposition using an energy-resolved mass spectrometer and a Langmuir probe in an Ar/H{sub 2} radio frequency magnetron discharge

The plasma parameters and ion energy distributions (IED) of the dominant species in an Ar-H{sub 2} discharge are investigated with an energy resolved mass spectrometer and a Langmuir probe. The plasmas are generated in a conventional magnetron chamber powered at 150 W, 13.56 MHz at hydrogen flow rates ranging from 0 to 25 sccm with a fixed argon gas flow rate of 15 sccm. Various H{sub n}{sup +}, SiH{sub n}{sup +}, SiH{sub n} fragments (with n = 1, 2, 3) together with Ar{sup +} and ArH{sup +} species are detected in the discharge. The most important species for the film deposition is SiH{sub n} (with n = 0, 1, 2). H fragments affect the hydrogen content in the material. The flux of Ar{sup +} decreases and the flux of ArH{sup +} increases when the hydrogen flow rate is increased; however, both fluxes saturate at hydrogen flow rates above 15 sccm. Electron density, n{sub e}, electron energy, T{sub e}, and ion density, n{sub i}, are estimated from the Langmuir probe data. T{sub e} is below 1.2 eV at hydrogen flow rates below 8 sccm, and about 2 eV at flow rates above 8 sccm. n{sub e} and n{sub i} decrease with increased hydrogen flow but the ratio of n{sub i} to n{sub e} increases. The formation of H{sup +} ions with energies above 36 eV and electrons with energies greater than 2 eV contributes to the decrease in hydrogen content at hydrogen flow rates above 8 sccm. Analysis of the IEDs indicates an inter-dependence of the species and their contribution to the thin film growth and properties.

36 MATERIALS SCIENCE↗

Alfven's critical ionization velocity observed in high power impulse magnetron sputtering discharges

Azimuthally rotating dense plasma structures, spokes, have recently been detected in several high power impulse magnetron sputtering (HiPIMS) devices used for thin film deposition and surface treatment, and are thought to be important for plasma buildup, energizing of electrons, as well as cross-B transport of charged particles. In this work, the drift velocities of these spokes are shown to be strongly correlated with the critical ionization velocity, CIV, proposed by Alfven. It is proposed as the most promising approach in combining the CIV and HiPIMS research fields is to focus on the role of spokes in the process of electron energization.

36 MATERIALS SCIENCE↗

Magnetron-sputter deposition of high-indium-content n-AlInN thin film on p-Si(001) substrate for photovoltaic applications

Al{sub 0.278}In{sub 0.722}N thin films have been grown on p-type Si(001) and c-plane sapphire substrates by employing radio-frequency magnetron-sputter deposition at elevated temperatures. High-resolution x-ray diffraction, as well as pole-figure measurements, reveals no phase separation of the thin films. The Al{sub 0.278}In{sub 0.722}N film grown on p-Si(001) substrate is a typical fiber-texture with AlInN(0001)//Si(001) while that on the c-sapphire exhibits the onset of epitaxy. Microscopic studies reveal that the growth is dominated by a columnar mechanism and the average columnar grain diameter is about 31.5 and 50.8 nm on p-Si(001) and c-sapphire substrates, respectively. Photoluminescence at room-temperature exhibits a strong emission peak at 1.875 eV, smaller than the optical absorption edge (2.102 eV) but larger than the theoretical bandgap energy (1.70 eV), which is attributable to the band-filling effect, as is supported by the high electron density of 4.5 Multiplication-Sign 10{sup 20} cm{sup -3}. The n-Al{sub 0.278}In{sub 0.722}N/p-Si(001) heterostructure is tested for solar cells and the results are discussed based on the I-V characteristics and their fittings.

36 MATERIALS SCIENCE↗

Structural-dependent thermal conductivity of aluminium nitride produced by reactive direct current magnetron sputtering

This Letter reports the thermal conductivity of aluminium nitride (AlN) thin-films deposited by reactive DC magnetron sputtering on single-crystal silicon substrates (100) with varying plasma and magnetic conditions achieving different crystalline qualities. The thermal conductivity of the films was measured at room temperature with the transient hot-strip technique for film thicknesses ranging from 100 nm to 4000 nm. The thermal conductivity was found to increase with the thickness depending on the synthesis conditions and film microstructure. The conductivity in the bulk region of the films, so-called intrinsic conductivity, and the boundary resistance were in the range [120-210] W m{sup -1} K{sup -1} and [2-30 Multiplication-Sign 10{sup -9}] K m{sup 2} W{sup -1}, respectively, in good agreement with microstructures analysed by x-ray diffraction, high-resolution-scanning-electron-microscopy, and transmission-electron-microscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural evolution of thin film vanadium oxide prepared by pulsed-direct current magnetron sputtering

Vanadium oxide (VO{sub x}) thin films have been deposited by pulsed-DC magnetron sputtering using a metallic vanadium target in a reactive argon and oxygen environment. While the process parameters (power, total pressure, oxygen-to-argon ratio) remained constant, the deposition time was varied to produce films between 75 {+-} 6 and 2901 {+-} 30 A thick, which were then optically and electrically characterized. The complex dielectric function spectra ({epsilon} = {epsilon}{sub 1} + i{epsilon}{sub 2}) of the films from 0.75 to 5.15 eV were extracted by ex situ, multiple-angle spectroscopic ellipsometry (SE) measurements for the series of varied thickness VO{sub x} samples. Significant changes in {epsilon} and resistivity occur as a function of thickness, indicating the correlations exist between the electrical and the optical properties over this spectral range. In addition, in situ measurements via real time SE (RTSE) were made on the film grown to the largest thickness to track optical property and structural variations during growth. RTSE was also used to characterize changes in the film occurring after growth was completed, namely during post sputtering in the presence of argon and oxygen while the sample is shielded, and atmospheric exposure. RTSE indicates that the exposure of the film to the argon and oxygen environment, regardless of the shutter isolating the target, causes up to 200 A of the top surface of the deposited film to become more electrically resistive as evidenced by variations in {epsilon}. Exposure of the VO{sub x} thin film to atmospheric conditions introduces a similar change in {epsilon}, but this change occurs throughout the bulk of the film. A combination of these observations with RTSE results indicates that thinner, less ordered VO{sub x} films are more susceptible to drastic changes due to atmospheric exposure and that microstructural variations in this material ultimately control its environmental stability.

36 MATERIALS SCIENCE↗

Boron-rich plasma by high power impulse magnetron sputtering of lanthanum hexaboride

Boron-rich plasmas have been obtained using a LaB{sub 6} target in a high power impulse sputtering (HiPIMS) system. The presence of {sup 10}B{sup +}, {sup 11}B{sup +}, Ar{sup 2+}, Ar{sup +}, La{sup 2+}, and La{sup +} and traces of La{sup 3+}, {sup 12}C{sup +}, {sup 14}N{sup +}, and {sup 16}O{sup +} have been detected using an integrated mass and energy spectrometer. Peak currents as low as 20 A were sufficient to obtain plasma dominated by {sup 11}B{sup +} from a 5 cm planar magnetron. The ion energy distribution function for boron exhibits an energetic tail extending over several 10 eV, while argon shows a pronounced peak at low energy (some eV). This is in agreement with models that consider sputtering (B, La) and gas supply (from background and 'recycling'). Strong voltage oscillations develop at high current, greatly affecting power dissipation and plasma properties.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Plasma diagnostics of low pressure high power impulse magnetron sputtering assisted by electron cyclotron wave resonance plasma

This paper reports on an investigation of the hybrid pulsed sputtering source based on the combination of electron cyclotron wave resonance (ECWR) inductively coupled plasma and high power impulse magnetron sputtering (HiPIMS) of a Ti target. The plasma source, operated in an Ar atmosphere at a very low pressure of 0.03 Pa, provides plasma where the major fraction of sputtered particles is ionized. It was found that ECWR assistance increases the electron temperature during the HiPIMS pulse. The discharge current and electron density can achieve their stable maximum 10 {mu}s after the onset of the HiPIMS pulse. Further, a high concentration of double charged Ti{sup ++} with energies of up to 160 eV was detected. All of these facts were verified experimentally by time-resolved emission spectroscopy, retarding field analyzer measurement, Langmuir probe, and energy-resolved mass spectrometry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electrical and optical properties of Ta-Si-N thin films deposited by reactive magnetron sputtering

The electrical and optical properties of Ta{sub x}Si{sub y}N{sub z} thin films deposited by reactive magnetron sputtering from individual Ta and Si targets were studied in order to investigate the effects of nitrogen and silicon contents on both properties and their correlation to the film microstructure. Three sets of fcc-Ta{sub x}Si{sub y}N{sub z} thin films were prepared: sub-stoichiometric Ta{sub x}Si{sub y}N{sub 0.44}, nearly stoichiometric Ta{sub x}Si{sub y}N{sub 0.5}, and over-stoichiometric Ta{sub x}Si{sub y}N{sub 0.56}. The optical properties were investigated by near-normal-incidence reflectivity and ellipsometric measurements in the optical energy range from 0.375 eV to 6.8 eV, while the d.c. electrical resistivity was measured in the van der Pauw configuration from 20 K to 300 K. The optical and electrical measurements were interpreted using the standard Drude-Lorentz model and the so-called grain boundary scattering model, respectively. The electronic properties were closely correlated with the compositional and structural modifications of the Ta{sub x}Si{sub y}N{sub z} films due to variations in the stoichiometry of the fcc-TaN{sub z} system and the addition of Si atoms. According to the nitrogen and silicon contents, fcc-Ta{sub x}Si{sub y}N{sub z} films can exhibit room temperature resistivity values ranging from 10{sup 2} {mu}{Omega} cm to about 6 Multiplication-Sign 10{sup 4} {mu}{Omega} cm. The interpretation of the experimental temperature-dependent resistivity data within the Grain Boundary Scattering model, combined with the results from optical investigations, showed that the mean electron transmission probability G and the free carriers concentration, N, are the main parameters that control the transport properties of these films. The results indicated that the correlation between electrical and optical measurements with the chemical composition and the nanostructure of the Ta{sub x}Si{sub y}N{sub z} thin films provides a pertinent and consistent description of the evolution of the Ta-Si-N system from a solid solution to a nanocomposite material due to the addition of Si atoms.

36 MATERIALS SCIENCE↗