SEARCH · Engineering Papers

Results for “Low Reynolds Number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1926

Preliminary wing model tests in the variable density wind tunnel of the National Advisory Committee for Aeronautics

This report contains the results of a series of tests with three wing models. By changing the section of one of the models and painting the surface of another, the number of models tested was increased to five. The tests were made in order to obtain some general information on the air forces on wing sections at a high Reynolds number and in particular to make sure that the Reynolds number is really the important factor, and not other things like the roughness of the surface and the sharpness of the trailing edge. The few tests described in this report seem to indicate that the air forces at a high Reynolds number are not equivalent to respective air forces at a low Reynolds number (as in an ordinary atmospheric wind tunnel). The drag appears smaller at a high Reynolds number and the maximum lift is increased in some cases. The roughness of the surface and the sharpness of the trailing edge do not materially change the results, so that we feel confident that tests with systematic series of different wing sections will bring consistent results, important and highly useful to the designer.

Munk, Max M↗

NASA NTRS2000

Comparison of Predicted and Measured Turbine Vane Rough Surface Heat Transfer

The proposed paper compares predicted turbine vane heat transfer for a rough surface over a wide range of test conditions with experimental data. Predictions were made for the entire vane surface. However, measurements were made only over the suction surface of the vane, and the leading edge region of the pressure surface. Comparisons are shown for a wide range of test conditions. Inlet pressures varied between 3 and 15 psia, and exit Mach numbers ranged between 0.3 and 0.9. Thus, while a single roughened vane was used for the tests, the effective rougness,(k(sup +)), varied by more than a factor of ten. Results were obtained for freestream turbulence levels of 1 and 10%. Heat transfer predictions were obtained using the Navier-Stokes computer code RVCQ3D. Two turbulence models, suitable for rough surface analysis, are incorporated in this code. The Cebeci-Chang roughness model is part of the algebraic turbulence model. The k-omega turbulence model accounts for the effect of roughness in the application of the boundary condition. Roughness causes turbulent flow over the vane surface. Even after accounting for transition, surface roughness significantly increased heat transfer compared to a smooth surface. The k-omega results agreed better with the data than the Cebeci-Chang model. However, the low Reynolds number k-omega model did not accurately account for roughness when the freestream turbulence level was low. The high Reynolds number version of this model was more suitable when the freestream turbulence was low.

Boyle, R. J.↗

NASA NTRS2003

Boundary-Layer Separation Control under Low-Pressure Turbine Airfoil Conditions using Glow-Discharge Plasma Actuators

Modem low-pressure turbines, in general, utilize highly loaded airfoils in an effort to improve efficiency and to lower the number of airfoils needed. Typically, the airfoil boundary layers are turbulent and fully attached at takeoff conditions, whereas a substantial fraction of the boundary layers on the airfoils may be transitional at cruise conditions due to the change of density with altitude. The strong adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation at the latter low Reynolds number conditions. Large separation bubbles, particularly those which fail to reattach, cause a significant degradation of engine efficiency. A component efficiency drop of the order 2% may occur between takeoff and cruise conditions for large commercial transport engines and could be as large as 7% for smaller engines at higher altitude. An efficient means of of separation elimination/reduction is, therefore, crucial to improved turbine design. Because the large change in the Reynolds number from takeoff to cruise leads to a distinct change in the airfoil flow physics, a separation control strategy intended for cruise conditions will need to be carefully constructed so as to incur minimum impact/penalty at takeoff. A complicating factor, but also a potential advantage in the quest for an efficient strategy, is the intricate interplay between separation and transition for the situation at hand. Volino gives a comprehensive discussion of several recent studies on transition and separation under low-pressure-turbine conditions, among them one in the present facility. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions. If the transition occurs early in the boundary layer then separation may be reduced or completely eliminated. Transition in the shear layer of a separation bubble can lead to rapid reattachment. This suggests using control mechanisms to trigger and enhance early transition. Gad-el-Hak provides a review of various techniques for flow control in general and Volino discusses recent studies on separation control under low-pressure-turbine conditions utilizing passive as well as active devices. As pointed out by Volino, passive devices optimized for separation control at low Reynolds numbers tend to increase losses at high Reynolds numbers, Active devices have the attractive feature that they can be utilized only in operational regimes where they are needed and when turned off would not affect the flow. The focus in the present paper is an experimental Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modem low-pressure-turbine airfoil ('Pak-B'). The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2%) and high (2.5%) Gee-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface- flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control. of active separation control using glow discharge plasma actuators.

Hultgren, Lennart S.↗

NASA NTRS1983

Subsonic high-angle-of-attack aerodynamic characteristics of a cone and cylinder with triangular cross sections and a cone with a square cross section

Experiments were conducted in the 12-Foot Pressure Wind Tunnel at Ames Research Center on three models with noncircular cross sections: a cone having a square cross section with rounded corners and a cone and cylinder with triangular cross sections and rounded vertices. The cones were tested with both sharp and blunt noses. Surface pressures and force and moment measurements were obtained over an angle of attack range from 30 deg to 90 deg and selected oil-flow experiments were conducted to visualize surface flow patterns. Unit Reynolds numbers ranged from 0.8x1,000,000/m to 13.0x1,000,000/m at a Mach number of 0.25, except for a few low-Reynolds-number runs at a Mach number of 0.17. Pressure data, as well as force data and oil-flow photographs, reveal that the three dimensional flow structure at angles of attack up to 75 deg is very complex and is highly dependent on nose bluntness and Reynolds number. For angles of attack from 75 deg to 90 deg the sectional aerodynamic characteristics are similar to those of a two dimensional cylinder with the same cross section.

Clarkson, M. H.↗

NASA NTRS1991

Advanced aircraft for atmospheric research

The development of aircraft for high-altitude research is described in terms of program objectives and environmental, technological limitations, and the work on the Perseus A aircraft. The need for these advanced aircraft is proposed in relation to atmospheric science issues such as greenhouse trapping, the dynamics of tropical cyclones, and stratospheric ozone. The implications of the study on aircraft design requirements is addressed with attention given to the basic categories of high-altitude, long-range, long-duration, and nap-of-the-earth aircraft. A strategy is delineated for a platform that permits unique stratospheric measurements and is a step toward a more advanced aircraft. The goal of Perseus A is to carry scientific air sampling payloads weighing at least 50 kg to altitudes of more than 25 km. The airfoils are designed for low Reynolds numbers, the structural weight is very low, and the closed-cycle power plant runs on liquid oxygen.

Russell, P.↗

NASA NTRS1994

Scale disparity and spectral transfer in anisotropic numerical turbulence

To study the effect of cancellations within long-range interactions on local isotropy at the small scales, we calculate explicitly the degree of cancellation in distant interactions in the simulations of Yeung & Brasseur and Yeung, Brasseur & Wang using the single scale disparity parameter 's' developed by Zhou. In the simulations, initially isotropic simulated turbulence was subjected to coherent anisotropic forcing at the large scales and the smallest scales were found to become anisotropic as a consequence of direct large-small scale couplings. We find that the marginally distant interactions in the simulation do not cancel out under summation and that the development of small-scale anisotropy is indeed a direct consequence of the distant triadic group, as argued by Yeung, et. al. A reduction of anisotropy at later times occurs as a result of the isotropizing influences of more local energy-cascading triadic interactions. Nevertheless, the local-to-nonlocal triadic group persists as an isotropizing influence at later times. We find that, whereas long-range interactions, in general, contribute little to net energy transfer into or out of a high wavenumber shell k, the anisotropic transfer of component energy within the shell increases with increasing scale separations. These results are consistent with results by Zhou, and Brasseur & Wei, and suggest that the anisotropizing influences of long range interactions should persist to higher Reynolds numbers. The residual effect of the forced distant group in this low-Reynolds number simulation is found to be forward cascading, on average.

Zhou, YE↗

NASA NTRS2001

Overview of Propulsion Systems for a Mars Aircraft

The capabilities and performance of an aircraft depends greatly on the ability of the propulsion system to provide thrust. Since the beginning of powered flight, performance has increased in step with advancements in aircraft propulsion systems. These advances in technology from combustion engines to jets and rockets have enabled aircraft to exploit our atmospheric environment and fly at altitudes near the Earth's surface to near orbit at speeds ranging from hovering to several times the speed of sound. One of the main advantages of our atmosphere for these propulsion systems is the availability of oxygen. Getting oxygen basically "free" from the atmosphere dramatically increases the performance and capabilities of an aircraft. This is one of the reasons our present-day aircraft can perform such a wide range of tasks. But this advantage is limited to Earth; if we want to fly an aircraft on another planetary body, such as Mars, we will either have to carry our own source of oxygen or use a propulsion system that does not require it. The Mars atmosphere, composed mainly of carbon dioxide, is very thin. Because of this low atmospheric density, an aircraft flying on Mars will most likely be operating, in aerodynamical terms, within a very low Reynolds number regime. Also, the speed of sound within the Martian environment is approximately 20 percent less than it is on Earth. The reduction in the speed of sound plays an important role in the aerodynamic performance of both the aircraft itself and the components of the propulsion system, such as the propeller. This low Reynolds number-high Mach number flight regime is a unique flight environment that is very rarely encountered here on Earth.

Colozza, Anthony J.↗

NASA NTRS1993

Prediction of stall and post-stall behavior of airfoils at low and high Reynolds numbers

An interactive boundary-layer method, together with the e(super n)-approach to the calculation of transition, has been used to predict the stall and post-stall behavior of airfoils at low and high Reynolds numbers. The turbulence model is based on the Cebeci-Smith algebraic eddy-viscosity formulation with improvements for strong pressure gradient effects and transitional flows at low Reynolds numbers. Comparison of calculated results for incompressible flows indicate good agreement with experiment for a wide range of Reynolds numbers. Preliminary calculations for low Mach number flows with this interactive method with compressibility corrections to the panel method indicate that, at a Mach number of 0.3, the compressibility effect on (C sub Q)max is not negligible.

Cebeci, T.↗

NASA NTRS1991

Large-eddy simulation of compressible turbulence

The increase in the range of length scales with increasing Reynolds number limits the direct simulation of turbulent flows to relatively simple geometries and low Reynolds numbers. However, since most flows of engineering interest occur at much higher Reynolds number than is currently within the capabilities of full simulation, prediction of these flow fields can only be obtained by solving some suitably-averaged set of governing equations. In the traditional Reynolds-averaged approach, the Navier-Stokes equations are averaged over time. This in turn yields correlations between various turbulence fluctuations. It is these terms, e.g. the Reynolds stresses, for which a turbulence model must be derived. Turbulence modeling of incompressible flows has received a great amount of attention in the literature. An area of research that has received comparatively less attention is the modeling of compressible turbulent flows. An approach to simulating compressible turbulence at high Reynolds numbers is through the use of Large-Eddy Simulation (LES). In LES the dependent variables are decomposed into a large-scale (resolved) component and a sub-grid scale component. It is the small-scale components of the velocity field which are presumably more homogeneous than the large scales and, therefore, more easily modeled. Thus, it seems plausible that simpler models, which should be more universal in character than those employed in second-order closure schemes, may be developed for LES of compressible turbulence. The objective of the present research, therefore, is to explore models for the Large-Eddy Simulation of compressible turbulent flows. Given the recent successes of Zeman in second order closure modeling of compressible turbulence, model development was guided by principals employed in second-order closures.

Squires, Kyle D.↗

NASA NTRS1981

Instability and transition in rotating disk flow

The stability of three-dimensional rotating disk flow is investigated, including the effects of Coriolis forces and streamline curvature. The numerical results show that the critical Reynolds number for establishment of stationary vortex flow is 287. These vortices spiral outward at an angle of about 11.2 deg, and transition to turbulence occurs when their total amplification is about e to the 11th. New experimental results are also reported on the spatial growth rates of the stationary vortices. It is shown that the analysis gives growth rates that compare much better with the experimental results than do results obtained using the Orr-Sommerfeld equation. The experimental results tend to support the numerical prediction that the number of stationary vortices varies directly with the Reynolds number. The calculations also indicate the existence of weakly unstable propagating (type II) modes at low Reynolds numbers (Critical Reynolds Number being approximately equal to 49).

Malik, M. R.↗

NASA NTRS1990

Calculations of the flow past bluff bodies, including tilt-rotor wing sections at alpha = 90 deg

An attempt was made to model in two dimensions the effects of rotor downwash on the wing of the tilt-rotor aircraft and to compute the drag force on airfoils at - 90 deg angle of attack, using a well-established Navier-Stokes code. However, neither laminar nor turbulent calculations agreed well with drag and base-pressure measurements at high Reynolds numbers. Therefore, further efforts were concentrated on bluff-body flows past various shapes at low Reynolds numbers, where a strong vortex shedding is observed. Good results were obtained for a circular cylinder, but the calculated drag of a slender ellipse at right angles to the freestream was significantly higher than experimental values reported in the literature for flat plates. Similar anomalous results were obtained on the tilt-rotor airfoils, although the qualitative effects of flap deflection agreed with the wind tunnel data. The ensemble of results suggest that there may be fundamental differences in the vortical wakes of circular cylinders and noncircular bluff bodies.

Raghavan, V.↗

NASA NTRS1984

Cryogenic wind tunnel technology. A way to measurement at higher Reynolds numbers

The goals, design, problems, and value of cryogenic transonic wind tunnels being developed in Europe are discussed. The disadvantages inherent in low-Reynolds-number (Re) wind tunnel simulations of aircraft flight at high Re are reviewed, and the cryogenic tunnel is shown to be the most practical method to achieve high Re. The design proposed for the European Transonic Wind tunnel (ETW) is presented: parameters include cross section. DISPLAY 83A46484/2 = 4 sq m, operating pressure = 5 bar, temperature = 110-120 K, maximum Re = 40 x 10 to the 6th, liquid N2 consumption = 40,000 metric tons/year, and power = 39,5 MW. The smaller Cologne subsonic tunnel being adapted to cryogenic use for preliminary studies is described. Problems of configuration, materials, and liquid N2 evaporation and handling and the research underway to solve them are outlined. The benefits to be gained by the construction of these costly installations are seen more in applied aerodynamics than in basic research in fluid physics. The need for parallel development of both high Re tunnels and computers capable of performing high-Re numerical analysis is stressed.

Beck, J. W.↗

NASA NTRS1973

Three-dimensional hypersonic transitional/turbulent mean flow profiles.

Detailed three-dimensional compressible transitional/turbulent boundary-layer profiles are presented for use as test cases in numerical and integral calculation procedures. The profiles were obtained from tests conducted in the Mach 20 leg of the Langley High Reynolds Number Helium Facility. The presented data represent an arduous test case for analytical prediction methods, since 'low Reynolds number' and precursor transition effects should probably be accounted for to accurately predict the boundary-layer growth and development.

Fischer, M. C.↗

NASA NTRS1992

Modeling variable blowing effects in the turbulent hypersonic boundary layer

Studies of the effects of variable blowing in turbulent hypersonic boundary layers are presented. Numerical calculations of the skin friction and surface heat transfer rates are compared to the experimental measurements of Holden (1990) for a slender cone at zero angle of attack in steady flows at Mach numbers of 11 and 13. An analysis of the transpiration feed system of the cone model was performed and showed that the blowing rate could be variable along the cone surface. This effect is confirmed by internal pressure measurements which were taken inside the cone model. The blowing rates are recalibrated using the internal gauge readings and used as the wall boundary condition for a compressible turbulent boundary layer calculation using the low Reynolds number k-epsilon model of Chien (1982). At low blowing rates, the boundary layer calculations indicate that a situation where both the effects of suction and blowing are present within the same flow. The results show excellent qualitative prediction of the experimental data.

Vanosdol, John G.↗

NASA NTRS1995

Experimental study of the effects of Reynolds number on high angle of attack aerodynamic characteristics of forebodies during rotary motion

The National Aeronautics and Space Administration and the Defense Research Agency (United Kingdom) have ongoing experimental research programs in rotary-flow aerodynamics. A cooperative effort between the two agencies is currently underway to collect an extensive database for the development of high angle of attack computational methods to predict the effects of Reynolds number on the forebody flowfield at dynamic conditions, as well as to study the use of low Reynolds number data for the evaluation of high Reynolds number characteristics. Rotary balance experiments, including force and moment and surface pressure measurements, were conducted on circular and rectangular aftbodies with hemispherical and ogive noses at the Bedford and Farnborough wind tunnel facilities in the United Kingdom. The bodies were tested at 60 and 90 deg angle of attack for a wide range of Reynolds numbers in order to observe the effects of laminar, transitional, and turbulent flow separation on the forebody characteristics when rolling about the velocity vector.

Pauley, H.↗

NASA NTRS1999

Predicting Turbulent Convective Heat Transfer in Three-Dimensional Duct Flows

The performance of an explicit algebraic stress model is assessed in predicting the turbulent flow and forced heat transfer in straight ducts, with square, rectangular, trapezoidal and triangular cross-sections, under fully developed conditions over a range of Reynolds numbers. Iso-thermal conditions are imposed on the duct walls and the turbulent heat fluxes are modeled by gradient-diffusion type models. At high Reynolds numbers (>/= 10(exp 5)), wall functions are used for the velocity and temperature fields; while at low Reynolds numbers damping functions are introduced into the models. Hydraulic parameters such as friction factor and Nusselt number are well predicted even when damping functions are used, and the present formulation imposes minimal demand on the number of grid points without any convergence or stability problems. Comparison between the models is presented in terms of the hydraulic parameters, friction factor and Nusselt number, as well as in terms of the secondary flow patterns occurring within the ducts.

Rokni, M.↗

NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗

NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

Sohn, K. H.↗