Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lift Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Development of the 10% NASA CRM High-Lift Common Research Model (CRM-HL)

A 10%-scale Common Research Model-high lift version (CRM-HL) was developed to support extensive experimental investigations in the areas of active flow control, control surface optimization for landing and take-off, acoustic technology development, and computational fluid dynamics code validation to name a few. The CRM-HL was designed to have modular components that will enable the model to be tested in the following three forms: (1) conventional high-lift (CHL) configuration, (2) Active Flow Control (AFC) enabled simple hinged flap high-lift (SHL) configuration, and (3) CHL configuration with noise reduction treatments for the slats and/or the flaps. This paper describes the design, analysis, and fabrication of the CRM-HL for testing in the NASA Langley Research Center (LaRC) 14 by 22-Foot Subsonic Tunnel (14x22) and other wind tunnels as deemed appropriate by the research community such as the Qinetiq 5 Meter tunnel.

Jared S. Fell↗
DOE OSTI2022

Non-trivial symmetries in quantum landscapes and their resilience to quantum noise

Very little is known about the cost landscape for parametrized Quantum Circuits (PQCs). Nevertheless, PQCs are employed in Quantum Neural Networks and Variational Quantum Algorithms, which may allow for near-term quantum advantage. Such applications require good optimizers to train PQCs. Recent works have focused on quantum-aware optimizers specifically tailored for PQCs. However, ignorance of the cost landscape could hinder progress towards such optimizers. In this work, we analytically prove two results for PQCs: (1) We find an exponentially large symmetry in PQCs, yielding an exponentially large degeneracy of the minima in the cost landscape. Alternatively, this can be cast as an exponential reduction in the volume of relevant hyperparameter space. (2) We study the resilience of the symmetries under noise, and show that while it is conserved under unital noise, non-unital channels can break these symmetries and lift the degeneracy of minima, leading to multiple new local minima. Based on these results, we introduce an optimization method called Symmetry-based Minima Hopping (SYMH), which exploits the underlying symmetries in PQCs. Our numerical simulations show that SYMH improves the overall optimizer performance in the presence of non-unital noise at a level comparable to current hardware. Overall, this work derives large-scale circuit symmetries from local gate transformations, and uses them to construct a noise-aware optimization method.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

FOILPOLARS (Grassmannian Foil Shape Sweeps for Polar Generation) [SWR-26-095]

FOILPOLARS (Grassmannian Foil Shape Sweeps for Polar Generation): Multifidelity aerodynamic polar data generation for hydrofoil/tidal-turbine airfoil sections. Foilpolars ties together three pieces: *AeroSandbox supplies the baseline airfoil coordinates (UIUC database). *G2Aero parameterizes those shapes on a Grassmannian manifold (Karcher mean + PGA basis) and samples new perturbed shapes around that basis. *XFoil (panel method) and NeuralFoil (neural-network surrogate, shipped with AeroSandbox) each solve the resulting shapes for lift, drag, moment, and pressure at the swept angles of attack, Reynolds numbers, and n_crit values. Design optimization of foil shapes in a computationally efficient way requires polars data across many candidate shapes, not just a handful of baseline foils. However, high-fidelity CFD at that scale is too costly, and naive shape perturbation strays from realistic geometries. FOILPOLARS addresses this by loading baseline airfoils (via AeroSandbox) and mapping them onto a Grassmannian manifold (via G2Aero), computing a Karcher mean and principal geodesic analysis (PGA) basis. New shapes are sampled by perturbing PGA coefficients, keeping them close to the manifold of realistic foils. Each sampled shape is evaluated across a configurable sweep of angle of attack, Reynolds number, and critical amplification factor using two solvers: XFoil (panel method) and NeuralFoil (neural-network surrogate), producing a paired dataset of lift, drag, moment, pressure, convergence, and confidence, indexed alongside each shape's PGA coefficients and shared Grassmannian basis in a single xarray dataset. From this, FOILPOLARS produces convergence summaries and comparison plots per shape, Reynolds number, and n_crit. A command-line interface exposes each pipeline stage independently, supporting data-driven design, optimization, and machine-learning workflows for foils.

Sandhu, Rimple [National Laboratory of the Rockies↗
NASA NTRS1993

Investigation of aerodynamic design issues with regions of separated flow

Existing aerodynamic design methods have generally concentrated on the optimization of airfoil or wing shapes to produce a minimum drag while satisfying some basic constraints such as lift, pitching moment, or thickness. Since the minimization of drag almost always precludes the existence of separated flow, the evaluation and validation of these design methods for their robustness and accuracy when separated flow is present has not been aggressively pursued. However, two new applications for these design tools may be expected to include separated flow and the issues of aerodynamic design with this feature must be addressed. The first application of the aerodynamic design tools is the design of airfoils or wings to provide an optimal performance over a wide range of flight conditions (multipoint design). While the definition of 'optimal performance' in the multipoint setting is currently being hashed out, it is recognized that given a wide range of flight conditions, it will not be possible to ensure a minimum drag constraint at all conditions, and in fact some amount of separated flow (presumably small) may have to be allowed at the more demanding flight conditions. Thus a multipoint design method must be tolerant of the existence of separated flow and may include some controls upon its extent. The second application is in the design of wings with extended high speed buffet boundaries of their flight envelopes. Buffet occurs on a wing when regions of flow separation have grown to the extent that their time varying pressures induce possible destructive effects upon the wing structure or adversely effect either the aircraft controllability or passenger comfort. A conservative approach to the expansion of the buffet flight boundary is to simply expand the flight envelope of nonseparated flow under the assumption that buffet will also thus be alleviated. However, having the ability to design a wing with separated flow and thus to control the location, extent and severity of the separated flow regions may allow aircraft manufacturers to gain an advantage in the early design stages of an aircraft, when configuration changes are relatively inexpensive to make. The goal of the summer research at NASA Langley Research Center (LaRC) was twofold: first, to investigate a particular airfoil design problem observed under conditions of strong shock induced flow separation on the upper surface of an airfoil at transonic conditions; and second, to suggest and investigate design methodologies for the prediction (or detection) and control of flow separation. The context of both investigations was to use an existing two dimensional Navier-Stokes flow solver and the constrained direct/iterative surface curvature (CDISC) design algorithm developed at LaRC. As a lead in to the primary task, it was necessary to gain a familiarity with both the design method and the computational analysis and to perform the FORTRAN coding needed to couple them together.

Gally, Tom↗
NASA NTRS1994

Control of flow separation in airfoil/wing design applications

Existing aerodynamic design methods have generally concentrated on the optimization of airfoil or wing shapes to produce a minimum drag while satisfying some basic constraints such as lift, pitching moment, or thickness. Since the minimization of drag almost always precludes the existence of separated flow, the evaluation and validation of these design methods for their robustness and accuracy when separated flow is present has not been aggressively pursued. However, two new applications for these design tools may be expected to include separated flow and the issues of aerodynamic design with this feature must be addressed. The first application of the aerodynamic design tools is the design of airfoils or wings to provide an optimal performance over a wide range of flight conditions (multipoint design). While the definition of 'optimal performance' in the multipoint setting is currently being hashed out, it is recognized that given a wide enough range of flight conditions, it will not be possible to ensure a minimum drag constraint at all conditions, and in fact some amount of separated flow (presumably small) may have to be allowed at the more demanding flight conditions. Thus a multipoint design method must be tolerant of the existence of separated flow and may include some controls upon its extent. The second application is in the design of wings with extended high speed buffet boundaries of their flight envelopes. Buffet occurs on a wing when regions of flow separation have grown to the extent that their time varying pressures induce possible destructive effects upon the wing structure or adversely effect either the aircraft controllability or the passenger comfort. A conservative approach to the expansion of the buffet flight boundary is to simply expand the flight envelope of nonseparated flow under the assumption that buffet will also thus be alleviated. However, having the ability to design a wing with separated flow and thus to control the location, extent, and severity of the separated flow regions may allow aircraft manufacturers to gain an advantage in the early design stages of an aircraft, when configuration changes are relatively inexpensive to make. Continuing the work begun last year, an airfoil design package has been modified to provide some control over the existence and extent of flow separation. This package consists of a 2-D Navier-Stokes flow solver which is coupled to the CDISC (constrained direct/iterative surface curvature) design method. The first modification is a prediction method for determining whether separation is likely based solely upon a given pressure distribution. If separation is predicted but is undesirable, the new routines will modify the pressure distribution to alleviate the problem. This new pressure distribution is then used in the design method to generate a new aerodynamic shape. Since separation may be acceptable in some cases, particularly if the separation does not extend to the trailing edge, another added logic estimates the extent of separation based upon a correlation with calculated separated flow cases. If the flow behind a shock induced separation is not predicted to reattach before the trailing edge, the logic weakens the shock strength and otherwise alters the pressure distribution in order to promote reattachment. This later addition is as yet unreliable due to secondary separation effects, but additional work is being pursued to improve the method.

Gally, Thomas A.↗
DOE OSTI2021

Gen 3 Particle Pilot Plant (G3P3) -- High-Temperature Particle System for Concentrating Solar Power (Phases 1 and 2)

The U.S. Department of Energy Solar Energy Technologies Office initiated the Generation 3 Concentrating Solar Power (CSP) program to achieve higher operating temperatures (>700 °C) to enable next-generation CSP high-temperature power cycles such as the supercritical CO 2 (sCO2) Brayton Cycle. Three teams were selected to pursue high-temperature gas, liquid, and solid pathways for the heat-transfer media. Phases 1 and 2, which lasted from 2018 – 2020, consisted of design, modeling, and testing activities to further de-risk each of the technologies and develop a design for construction, commissioning, and operation of a pilot-scale facility in Phase 3 (2021 – 2024). This report summarizes the activities in Phases 1 and 2 for the solid-particle pathway led by Sandia National Laboratories. In Phases 1 and 2, Sandia successfully de-risked key elements of the proposed Gen 3 Particle Pilot Plant (G3P3) by improving the design, operation, and performance of key particle component technologies including the receiver, storage bins, particle-to-sCO2 heat exchanger, particle lift, and data acquisition and controls. Modeling and testing of critical components have led to optimized designs that meet desired performance metrics. Detailed drawings, piping and instrumentation diagrams, and process flow diagrams were generated for the integrated system, and structural analyses of the assembled tower structure were performed to demonstrate compliance with relevant codes and standards. Instrumentation and control systems of key subsystems were also demonstrated. Together with Bridgers & Paxton, Bohannan Huston, and Sandia Facilities, we have completed a 100% G3P3 tower design package with stamped engineering drawings suitable for construction bid in Phase 3.

14 SOLAR ENERGY↗
NASA NTRS1977

Optimization of active control systems to suppress flutter and minimize turbulence response

A method for optimizing an active control system which will suppress flutter and minimize the response of a lifting surface to atmospheric turbulence is presented. A mathematical search method is developed which will find a control law which will cause an active control system to flutter at a specified freestream velocity, air density, and Mach number. With the flutter velocity of the system held constant, the control law is then modified in such a way that the peak output power spectral density function of the angular response of a lifting surface (as a result of atmospheric turbulence) is minimized for a specified flight velocity which is less than the flutter velocity. The von Karman generalized power spectrum for the transverse components of turbulence is used in an example problem to increase the flutter velocity and minimize the turbulence response of a simplified delta-wing model which has leading and trailing edge control surfaces.

Rudisill, C. S.↗
NASA NTRS1983

Minimum-fuel aeroassisted coplanar orbit transfer using lift-modulation

Minimum-fuel trajectories and lift controls are computed for aeroassisted coplanar transfer from high orbit to low orbit. The optimal aeroassisted transfer requires less fuel than the all-propulsive Hohmann transfer for a wide range of high orbit to low orbit transfers. The optimal control program for the atmospheric portion of the transfer is to fly at maximum positive L/D initially to recover from the downward plunge, and then, to fly at negative L/D to level off the flight, such that the vehicle skips out of the atmosphere with a flight path angle near zero degrees. To avoid excessive heating rates, the vehicle flies initially at high angle of attack in order to slow down higher in the atmosphere, allowing recovery from the downward plunge, which occurs subsequently using the maximum positive L/D, to take place at a lower atmospheric density, or equivalently, at a higher altitude.

Mease, K. D.↗
NASA NTRS1996

Evolution of the revolutionary blended-wing-body

The Blended-Wing-Body (BWB) airplane concept represents a potential revolution in subsonic transport efficiency for Very Large Airplanes (VLA's). NASA is sponsoring an advanced concept study to demonstrate feasibility and begin development of this new class of airplane. In this study, 800 passenger BWB and conventional configuration airplanes have been compared for a 7000 nautical mile design range, where both airplanes are based on technology keyed to 2015 entry into service. The BWB has been found to be superior to the conventional configuration in the following areas: Fuel Burn--31% lower, Takeoff Weight -- 1 3% lower, Operating Empty Weight -- 10% lower, Total Thrust -- 16% lower, and Lift/Drag --35% higher. The BWB advantage results from a double deck cabin that extends spanwise providing structural and aerodynamic overlap with the wing. This reduces the total wetted area of the airplane and allows a high aspect ratio to be achieved, since the deep and stiff centerbody provides efficient structural wingspan. Further synergy is realized through buried engines that ingest the wing's boundary layer, and thus reduce effective ram drag. Relaxed static stability allows optimal span loading, and an outboard leading-edge slat is the only high-lift system required.

Liebeck, Robert H.↗
NASA NTRS1999

A PTC Optimization and Control Surface Interference Study HSR Airframe Technical Review

This report considers the effect of canard and horizontal tail vertical position on the aerodynamic characteristics of the PTC configuration without nacelles and diverters. This analysis is followed by three optimization studies using canard and tail incidence as design variables in the first problem followed by an optimization run with canard and tail incidence and wing camber design variables and finally an optimization run with canard incidence and wing camber. The first problem was run at fixed lift while the other two problems were run at fixed angle of attack. The final investigation reported here will show data from a component buildup study using the PTC configuration. This final study will show the aerodynamic interference between the canard, wing and horizontal tail.

Hicks, Raymond↗
NASA NTRS1977

Effect of flap deflection on the lift coefficient of wings operating in a biplane configuration

Biplane models with a lift flap were tested in a wind tunnel to study the effect of flap deflection on the aerodynamic coefficient of the biplane as well as of the individual wings. Optimization of the position flap was carried out, and the effect of changes in the chord length of the lower wing was determined for the aerodynamic structure of a biplane with a lift flap on the upper wing.

Stasiak, J.↗
NASA NTRS1995

Abort performance for a winged-body single-stage to orbit vehicle

Optimal control theory is employed to determine the performance of abort to orbit (ATO) and return to launch site (RTLS) maneuvers for a single-stage to orbit vehicle. The vehicle configuration examined is a seven engine, winged-body vehicle, that lifts-off vertically and lands horizontally. The abort maneuvers occur as the vehicle ascends to orbit and are initiated when the vehicle suffers an engine failure. The optimal control problems are numerically solved in discretized form via a nonlinear programming (NLP) algorithm. A description highlighting the attributes of this NLP method is provided. ATO maneuver results show that the vehicle is capable of ascending to orbit with a single engine failure at lift-off. Two engine out ATO maneuvers are not possible from the launch pad, but are possible after launch when the thrust to weight ratio becomes sufficiently large. Results show that single engine out RTLS maneuvers can be made for up to 180 seconds after lift-off and that there are scenarios for which RTLS maneuvers should be performed instead of ATP maneuvers.

Lyon, Jeffery A.↗
NASA NTRS1992

Aerodynamic characteristics of a hypersonic viscous optimized waverider at high altitudes

The present paper addresses the applicability of the basic concept of waveriding at high altitudes, and the extent to which the large viscous forces degrade the aerodynamic performance of waveriders. The waverider under consideration was designed using a continuum flow methodology. It is shown that the lift-to-drag ratio of high-altitude/high-Knudsen-number waveriders can be expected to be significantly lower than their low altitude/low Knudsen number counterparts. The aerodynamic performance of a representative waverider which was optimized for a 90-km, Mach-25 application is studied for altitudes ranging from 97 km to 145 km and incidence angles of 0 to 30 deg. Typical values of the lift-to-drag ratio were computed to be in the range of 0 to 0.3. Friction forces are mostly responsible for this poor performance. Friction forces account for more than 93 percent of the drag and significantly reduce lift.

Rault, Didier F. G.↗
NASA NTRS2009

Sonic Boom Research at NASA Dryden: Objectives and Flight Results from the Lift and Nozzle Change Effects on Tail Shock (LaNCETS) Project

The principal objective of the Supersonics Project is to develop and validate multidisciplinary physics-based predictive design, analysis and optimization capabilities for supersonic vehicles. For aircraft, the focus will be on eliminating the efficiency, environmental and performance barriers to practical supersonic flight. Previous flight projects found that a shaped sonic boom could propagate all the way to the ground (F-5 SSBD experiment) and validated design tools for forebody shape modifications (F-5 SSBD and Quiet Spike experiments). The current project, Lift and Nozzle Change Effects on Tail Shock (LaNCETS) seeks to obtain flight data to develop and validate design tools for low-boom tail shock modifications. Attempts will be made to alter the shock structure of NASA's NF-15B TN/837 by changing the lift distribution by biasing the canard positions, changing the plume shape by under- and over-expanding the nozzles, and changing the plume shape using thrust vectoring. Additional efforts will measure resulting shocks with a probing aircraft (F-15B TN/836) and use the results to validate and update predictive tools. Preliminary flight results are presented and are available to provide truth data for developing and validating the CFD tools required to design low-boom supersonic aircraft.

Moes, Timothy R.↗
NASA NTRS1999

Design Oriented Structural Modeling for Airplane Conceptual Design Optimization

The main goal for research conducted with the support of this grant was to develop design oriented structural optimization methods for the conceptual design of airplanes. Traditionally in conceptual design airframe weight is estimated based on statistical equations developed over years of fitting airplane weight data in data bases of similar existing air- planes. Utilization of such regression equations for the design of new airplanes can be justified only if the new air-planes use structural technology similar to the technology on the airplanes in those weight data bases. If any new structural technology is to be pursued or any new unconventional configurations designed the statistical weight equations cannot be used. In such cases any structural weight estimation must be based on rigorous "physics based" structural analysis and optimization of the airframes under consideration. Work under this grant progressed to explore airframe design-oriented structural optimization techniques along two lines of research: methods based on "fast" design oriented finite element technology and methods based on equivalent plate / equivalent shell models of airframes, in which the vehicle is modelled as an assembly of plate and shell components, each simulating a lifting surface or nacelle / fuselage pieces. Since response to changes in geometry are essential in conceptual design of airplanes, as well as the capability to optimize the shape itself, research supported by this grant sought to develop efficient techniques for parametrization of airplane shape and sensitivity analysis with respect to shape design variables. Towards the end of the grant period a prototype automated structural analysis code designed to work with the NASA Aircraft Synthesis conceptual design code ACS= was delivered to NASA Ames.

Livne, Eli↗
NASA NTRS1972

Optimized space shuttle trajectory simulation

A computer program for simulating optimized space shuttle trajectories is presented. The program considers the ascent, return, and synergetic maneuvers of lifting boosters and spacecraft. Other constraints on optimum trajectory such as maximum heating, acceleration, angle of attack, and excluded or included overflight or impact regions are examined. Mathematical models are included to support the theoretical aspects of the discussion.

Tramonti, L.↗
NASA NTRS1983

Optimal symmetric flight with an intermediate vehicle model

Optimal flight in the vertical plane with a vehicle model intermediate in complexity between the point-mass and energy models is studied. Flight-path angle takes on the role of a control variable. Range-open problems feature subarcs of vertical flight and singular subarcs. The class of altitude-speed-range-time optimization problems with fuel expenditure unspecified is investigated and some interesting phenomena uncovered. The maximum-lift-to-drag glide appears as part of the family, final-time-open, with appropriate initial and terminal transient exceeding level-flight drag, some members exhibiting oscillations. Oscillatory paths generally fail the Jacobi test for durations exceeding a period and furnish a minimum only for short-duration problems.

Menon, P. K. A.↗
NASA NTRS1991

Analysis and design of planar and non-planar wings for induced drag minimization

Improvements in the aerodynamic efficiency of commercial transport aircraft will reduce fuel usage with subsequent reduced cost, both monetary and environmental. To this end, the current research is aimed at reducing the overall drag of these aircraft with specific emphasis on reducing the drag generated by the lifting surfaces. The ultimate goal of this program is to create a wing design methodology which optimizes the geometry of the wing for lowest total drag within the constraints of a particular design specification. The components of drag which must be considered include profile drag, and wave drag. Profile drag is dependent upon, among other things, the airfoil section and the total wetted area. Induced drag, which is manifested as energy left in the wake by the trailing vortex system is mostly a function of wing span, but also depends on other geometric wing parameters. Wave drag of the wing, important in the transonic flight regime, is largely affected by the airfoil section, wing sweep, and so forth. The optimization problem is that of assessing the various parameters which contribute to the different components of wing drag, and determining the wing geometry which generates the best overall performance for a given aircraft mission. The primary thrust of the research effort to date was in the study of induced drag. Results from the study are presented.

Straussfogel, Dennis M.↗