SEARCH · Engineering Papers

Results for “Landing Gear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces. A slip-velocity-controlled, pressure-bias-modulated system

The braking and cornering response of a slip velocity controlled, pressure bias modulated aircraft antiskid braking system is investigated. The investigation, conducted on dry and wet runway surfaces, utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC 9 series 10 airplane. The landing gear strut was replaced by a dynamometer. The parameters, which were varied, included the carriage speed, tire loading, yaw angle, tire tread condition, brake system operating pressure, and runway wetness conditions. The effects of each of these parameters on the behavior of the skid control system is presented. Comparisons between data obtained with the skid control system and data obtained from single cycle braking tests without antiskid protection are examined.

Stubbs, S. M.↗

NASA NTRS1981

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces: Hydromechanically controlled system

The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The landing-gear strut was replaced by a dynamometer. During maximum braking, average braking behavior indexes based upon brake pressure, brake torque, and drag-force friction coefficient developed by the antiskid system were generally higher on dry surfaces than on wet surfaces. The three braking behavior indexes gave similar results but should not be used interchangeably as a measure of the braking of this antiskid sytem. During the transition from a dry to a flooded surface under heavy braking, the wheel entered into a deep skid but the antiskid system reacted quickly by reducing brake pressure and performed normally during the remainder of the run on the flooded surface. The brake-pressure recovery following transition from a flooded to a dry surface was shown to be a function of the antiskid modulating orifice.

Tanner, J. A.↗

NASA NTRSDate not supplied

Lessons Learned on the Use of Data Surfaces for Ffowcs Williams-Hawkings Calculations: Airframe Noise Applications

The use of integral solutions to the acoustic analogy-based Ffowcs Williams-Hawkings (FW-H) formulation is the defacto industrial and academic approach for assessing far-field acoustic behavior from airframe noise simulations. The methodology utilizes time-accurate flow variables obtained at arbitrary data surfaces to determine far-field spectra. The solid surface approach, where the time history of pressure is recorded on the surface of the aircraft, is generally preferred. Permeable surfaces, where pressure and velocity are recorded on a user-defined surface enclosing the aircraft, are also used. This paper seeks to share some of the valuable lessons we learned over the past several years on the limitations of the FW-H formulation and best practices for its successful application. We show results for various configurations comprising isolated landing gears, a business jet, a large commercial transport, and a generic low boom supersonic prototype, all at landing conditions. We demonstrate that the solid FW-H approach has significant accuracy limitations for most realistic cases and that the permeable FW-H approach may also fail in specific scenarios, requiring additional costly steps to extract the correct far-field noise spectra. Suggested guidelines for proper FW-H calculations are also given.

Acoustic propagation, Ffowcs Williams-Hawkings Cal↗

NASA NTRS1976

Effects of spoilers and gear on B-747 wake vortex velocities

Vortex velocities were measured in the wakes of four configurations of a 0.61-m span model of a B-747 aircraft. The wakes were generated by towing the model underwater in a ship model basin. Tangential and axial velocity profiles were obtained with a scanning laser velocimeter as the wakes aged to 35 span lengths behind the model. A 45 deg deflection of two outboard flight spoilers with the model in the landing configuration resulted in a 36 percent reduction in wake maximum tangential velocity, altered velocity profiles, and erratic vortex trajectories. Deployment of the landing gear with the inboard flaps in the landing position and outboard flaps retracted had little effect on the flap vortices to 35 spans, but caused the wing tip vortices to have: (1) more diffuse velocity profiles; (2) a 27 percent reduction in maximum tangential velocity; and (3) a more rapid merger with the flap vortices.

Luebs, A. B.↗

NASA NTRS1993

NASA Langley's Aircraft Landing Dynamics Facility

The Aircraft Landing Dynamics Facility (ALDF) is a unique facility with the ability to test aircraft landing gear systems on actual runway surfaces at operational ground speeds and loading conditions. A brief historical overview of the original Landing Loads Track (LLT) is given, followed by a detailed description of the new ALDF systems and operational capabilities.

Davis, Pamela A.↗

NASA NTRS1961

Considerations of Methods of Improving Helicopter Efficiency

Recent NASA helicopter research indicates that significant improvements in hovering efficiency, up to 7 percent, are available from the use of a special airfoil section formed by combining an NACA 632A015 thickness distribution with an NACA 230 mean line. This airfoil should be considered for flying-crane-type helicopters. Application of standard leading-edge roughness causes a large drop in efficiency; however, the cambered rotor is shown to retain its superiority over a rotor having a symmetrical airfoil when both rotors have leading-edge roughness. A simple analysis of available rotor static-thrust data indicates a greatly reduced effect of compressibility effects on the rotor profile-drag power than predicted from calculations. Preliminary results of an experimental study of helicopter parasite drag indicate the practicability of achieving an equivalent flat-plate parasite-drag area of less than 4 square feet for a rotor-head-pylon-fuselage configuration (landing gear retracted) in the 2,000-pound minimum-flying-weight class. The large drag penalty of a conventional skid-type landing (3.6 square feet) can be reduced by two-thirds by careful design. Clean, fair, and smooth fuselages that tend to have narrow, deep cross sections are shown to have advantages from the standpoint of drag and download. A ferry range of the order of 1,500 miles is indicated to be practicable for the small helicopter considered.

Dingeldein, Richard C.↗

NASA NTRS1976

Vortex interactions in multiple vortex wakes behind aircraft

A flow visualization technique has been developed which allows the nature of lift-generated wakes behind aircraft models to be investigated. Several different configurations of a 0.61-m span model of a Boeing 747-type transport aircraft were tested to allow observation of typical vortex interactions and merging in multiple vortex wakes. The vortices were identified by emitting tracer dyes from selected locations on the model. Wing span loading and model attitude were found to effect both vortex motions within the wake and resulting far-field wake velocity. Landing gear deployment caused a far-field reformation of vorticity behind a model configuration which dissipated concentrated vorticity in the near-field wake. A modified landing configuration was developed which appeared to significantly alleviate the concentrated wake vorticity.

Ciffone, D. L.↗

NASA NTRSDate not supplied

Aeroacoustic Computations of a Transonic Truss-Braced Wing Aircraft: Part 2 – Acoustic Signature and Noise Source Identification

High-fidelity, time-dependent simulations of a Boeing-designed, transonic, truss-braced-wing aircraft in cruise (clean) and landing configurations are leveraged to generate synthetic microphone-phased-array data for airframe noise prediction and assessment. These data sets are used to compute source localization (beamform) maps to determine the location and strength of primary and secondary airframe noise sources associated with this unique configuration. The synthetic phased-array implementation mimics the setup of a flight test. As this study is ongoing, preliminary integrated far-field spectra for the cruise configuration obtained at multiple spatial resolutions revealed significant tonal content that lacked convergence with increased resolution. The origin of several of these tones and their unusual convergence behavior was traced to the larger-than-normal trailing-edge thickness of the “as-tested” cruise model being simulated. Reducing the trailing-edge thickness to more realistic values eliminated most of the tones at low to moderate frequencies and improved spectrum convergence significantly. Applying lessons learned from the cruise simulations, several modifications to the geometry of the landing configuration were made and are described in this work. Results from permeable and solid Ffowcs-Williams and Hawkings surfaces at two different spatial resolutions (coarse and medium) are used to illustrate the major noise sources and determine convergence of the CLEAN integrated noise levels for the entire aircraft as well as major subcomponents. We demonstrate that the low-frequency content of the far-field spectrum is dominated by noise generated from the main landing gear, while the medium- and high-frequency content is dominated by the wing-leading-edge Krueger flaps. Since analysis of the acoustic maps for the landing configuration revealed several clusters of multiple sources along the wing leading edge, “high resolution” processing of the array data was used to distinguish more accurately the locations of sources.

Transonic Truss-Braced Wing↗

NASA NTRS1972

Aerospace applications of atmospheric rendezvous.

This paper studies the feasibility of the use of an atmospheric rendezvous concept to increase the efficiency and flexibility of space transportation systems. In this concept the second stage of a recoverable orbital launch vehicle or hypersonic transport would be built without wings, landing gear, or subsonic flight propulsion, and would be received in an atmospheric rendezvous by a carrier vehicle at the terminal point of flight for subsequent ferry to a landing site. Significant possibilities for weight improvement are shown and the attractiveness of a subsonic form of atmospheric rendezvous in either a towing or docking mode is illustrated.

Bird, J. D.↗

NASA NTRS2008

Preliminary Analysis of Acoustic Measurements from the NASA-Gulfstream Airframe Noise Flight Test

The NASA-Gulfstream joint Airframe Noise Flight Test program was conducted at the NASA Wallops Flight Facility during October, 2006. The primary objective of the AFN flight test was to acquire baseline airframe noise data on a regional jet class of transport in order to determine noise source strengths and distributions for model validation. To accomplish this task, two measuring systems were used: a ground-based microphone array and individual microphones. Acoustic data for a Gulfstream G550 aircraft were acquired over the course of ten days. Over twenty-four test conditions were flown. The test matrix was designed to provide an acoustic characterization of both the full aircraft and individual airframe components and included cruise to landing configurations. Noise sources were isolated by selectively deploying individual components (flaps, main landing gear, nose gear, spoilers, etc.) and altering the airspeed, glide path, and engine settings. The AFN flight test program confirmed that the airframe is a major contributor to the noise from regional jets during landing operations. Sound pressure levels from the individual microphones on the ground revealed the flap system to be the dominant airframe noise source for the G550 aircraft. The corresponding array beamform maps showed that most of the radiated sound from the flaps originates from the side edges. Using velocity to the sixth power and Strouhal scaling of the sound pressure spectra obtained at different speeds failed to collapse the data into a single spectrum. The best data collapse was obtained when the frequencies were left unscaled.

Khorrami, Mehdi R.↗

NASA NTRS1979

Low-speed aerodynamic performance of a high-aspect-ratio supercritical-wing transport model equipped with full-span slat and part-span double-slotted flaps

An investigation was conducted in the Langley V/STOL tunnel to determine the static longitudinal and lateral-directional aerodynamic characteristics of an advanced high-aspect-ratio supercritical-wing transport model equipped with a full-span leading-edge slat and part-span double-slotted trailing-edge flaps. This wide-body transport model was also equipped with spoiler and aileron control surfaces, flow-through nacelles, landing gear, movable horizontal tails, and interchangeable wing tips with aspect ratios of 10 and 12. The model was tested with leading-edge slat and trailing-edge flap combinations representative of cruise, climb, takeoff, and landing wing configurations. The tests were conducted at free-stream conditions corresponding to Reynolds numbers (based on mean geometric chord) of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle-of-attack range of -2 deg to 24 deg and a sideslip-angle range of -10 deg to 5 deg.

Morgan, H. L., Jr.↗

NASA NTRS2005

Integration Of Launch Vehicle Simulation/Analysis Tools And Lunar Cargo Lander Design

Part 2, which will be discussed in this report, will discuss the development of a Lunar Cargo Lander (unmanned launch vehicle) that will transport usable payload from Trans- Lunar Injection to the moon. The Delta IV-Heavy was originally used to transport the Lunar Cargo Lander to TLI, but other launch vehicles have been studied. In order to uncover how much payload is possible to land on the moon, research was needed in order to design the sub-systems of the spacecraft. The report will discuss and compare the use of a hypergolic and cryogenic system for its main propulsion system. The guidance, navigation, control, telecommunications, thermal, propulsion, structure, mechanisms, landing gear, command, data handling, and electrical power sub-systems were designed by scaling off other flown orbiters and moon landers. Once all data was collected, an excel spreadsheet was created to accurately calculate the usable payload that will land on the moon along with detailed mass and volume estimating relations. As designed, The Lunar Cargo Lander can plant 5,400 lbm of usable payload on the moon using a hypergolic system and 7,400 lbm of usable payload on the moon using a cryogenic system.

DeJean, George Brian↗

NASA NTRS2015

A Comparative Study of Simulated and Measured Gear-Flap Flow Interaction

The ability of two CFD solvers to accurately characterize the transient, complex, interacting flowfield asso-ciated with a realistic gear-flap configuration is assessed via comparison of simulated flow with experimental measurements. The simulated results, obtained with NASA's FUN3D and Exa's PowerFLOW® for a high-fidelity, 18% scale semi-span model of a Gulfstream aircraft in landing configuration (39 deg flap deflection, main landing gear on and off) are compared to two-dimensional and stereo particle image velocimetry measurements taken within the gear-flap flow interaction region during wind tunnel tests of the model. As part of the bench-marking process, direct comparisons of the mean and fluctuating velocity fields are presented in the form of planar contour plots and extracted line profiles at measurement planes in various orientations stationed in the main gear wake. The measurement planes in the vicinity of the flap side edge and downstream of the flap trailing edge are used to highlight the effects of gear presence on tip vortex development and the ability of the computational tools to accurately capture such effects. The present study indicates that both computed datasets contain enough detail to construct a relatively accurate depiction of gear-flap flow interaction. Such a finding increases confidence in using the simulated volumetric flow solutions to examine the behavior of pertinent aer-odynamic mechanisms within the gear-flap interaction zone.

Khorrami, Mehdi R.↗

NASA NTRS2014

Towards Full Aircraft Airframe Noise Prediction: Detached Eddy Simulations

Results from a computational study on the aeroacoustic characteristics of an 18%-scale, semi-span Gulf-stream aircraft model are presented in this paper. NASA's FUN3D unstructured compressible Navier-Stokes solver was used to perform steady and unsteady simulations of the flow field associated with this high-fidelity aircraft model. Solutions were obtained for free-air at a Mach number of 0.2 with the flap deflected at 39 deg, with the main gear off and on (the two baseline configurations). Initially, the study focused on accurately predicting the prominent noise sources at both flap tips for the baseline configuration with deployed flap only. Building upon the experience gained from this initial effort, subsequent work involved the full landing configuration with both flap and main landing gear deployed. For the unsteady computations, we capitalized on the Detached Eddy Simulation capability of FUN3D to capture the complex time-dependent flow features associated with the flap and main gear. To resolve the noise sources over a broad frequency range, the tailored grid was very dense near the flap inboard and outboard tips and the region surrounding the gear. Extensive comparison of the computed steady and unsteady surface pressures with wind tunnel measurements showed good agreement for the global aerodynamic characteristics and the local flow field at the flap inboard tip. However, the computed pressure coefficients indicated that a zone of separated flow that forms in the vicinity of the outboard tip is larger in extent along the flap span and chord than measurements suggest. Computed farfield acoustic characteristics from a FW-H integral approach that used the simulated pressures on the model solid surface were in excellent agreement with corresponding measurements.

Khorrami, Mehdi R.↗

NASA NTRS2004

Aeroacoustic Study of a 26%-Scale Semispan Model of a Boeing 777 Wing in the NASA Ames 40- by 80-Foot Wind Tunnel

An acoustic and aerodynamic study was made of a 26%-scale unpowered Boeing 777 aircraft semispan model in the NASA Ames 40- by 80-Foot Wind Tunnel for the purpose of identifying and attenuating airframe noise sources. Simulated approach and landing configurations were evaluated at Mach numbers between 0.12 and 0.24. Cruise configurations were evaluated at Mach numbers between 0.24 and 0.33. The research team used two Ames phased-microphone arrays, a large fixed array and a small traversing array, mounted under the wing to locate and compare various noise sources in the wing high-lift system and landing gear. Numerous model modifications and noise alleviation devices were evaluated. Simultaneous with acoustic measurements, aerodynamic forces were recorded to document aircraft conditions and any performance changes caused by the geometric modifications. Numerous airframe noise sources were identified that might be important factors in the approach and landing noise of the full-scale aircraft. Several noise-control devices were applied to each noise source. The devices were chosen to manipulate and control, if possible, the flow around the various tips and through the various gaps of the high-lift system so as to minimize the noise generation. Fences, fairings, tip extensions, cove fillers, vortex generators, hole coverings, and boundary-layer trips were tested. In many cases, the noise-control devices eliminated noise from some sources at specific frequencies. When scaled to full-scale third-octave bands, typical noise reductions ranged from 1 to 10 dB without significant aerodynamic performance loss.

Horne, W. Clifton↗

NASA NTRS1955

Ditching Investigation of a 1/11-Scale Model of the Chance Vought F7U-3 Airplane, TED NO. NACA DE 360

An investigation was made of a 1/11-scale dynamically similar model of the Chance Vought F7U-3 airplane to study its behavior when ditched. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and configurations were investigated. The behavior of the model was determined from visual observations, acceleration records, and motion-picture records of the ditchings. Data are presented in tabular form, sequence photographs, time-history acceleration curves, and plots of attitude change against time after contact. From the results of the investigation, it was concluded that the airplane should be ditched at the lowest speed and highest attitude consistent with adequate control. The aft part of the fuselage and the main landing-gear doors will probably be damaged. In a calm-water ditching under these conditions the airplane will probably skip slightly and then porpoise for the remainder of the run. Maximum longitudinal decelerations will be about 3 1/2g and maximum normal accelerations will be about 7g in a landing run of about 500 feet.

Fisher, Lloyd J.↗

NASA NTRS1980

Crash tests of four identical high-wing single-engine airplanes

Four identical four place, high wing, single engine airplane specimens with nominal masses of 1043 kg were crash tested at the Langley Impact Dynamics Research Facility under controlled free flight conditions. These tests were conducted with nominal velocities of 25 m/sec along the flight path angles, ground contact pitch angles, and roll angles. Three of the airplane specimens were crashed on a concrete surface; one was crashed on soil. Crash tests revealed that on a hard landing, the main landing gear absorbed about twice the energy for which the gear was designed but sprang back, tending to tip the airplane up to its nose. On concrete surfaces, the airplane impacted and remained in the impact attitude. On soil, the airplane flipped over on its back. The crash impact on the nose of the airplane, whether on soil or concrete, caused massive structural crushing of the forward fuselage. The liveable volume was maintained in both the hard landing and the nose down specimens but was not maintained in the roll impact and nose down on soil specimens.

Vaughan, V. L., Jr.↗

NASA NTRS1981

Low-speed aerodynamic performance of an aspect-ratio-10 supercritical-wing transport model equipped with a full-span slat and part-span and full-span double-slotted flaps

An investigation was conducted in the Langley 4 by 7 Meter Tunnel to determine the static longitudinal and lateral directional aerodynamic characteristics of an advanced aspect ratio 10 supercritical wing transport model equipped with a full span leading edge slat as well as part span and full span trailing edge flaps. This wide body transport model was also equipped with spoiler and aileron roll control surfaces, flow through nacelles, landing gear, and movable horizontal tails. Six basic wing configurations were tested: (1) cruise (slats and flaps nested), (2) climb (slats deflected and flaps nested), (3) part span flap, (4) full span flap, (5) full span flap with low speed ailerons, and (6) full span flap with high speed ailerons. Each of the four flapped wing configurations was tested with leading edge slat and trailing edge flaps deflected to settings representative of both take off and landing conditions. Tests were conducted at free stream conditions corresponding to Reynolds number of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle of attack range of 4 to 24, and a sideslip angle range of -10 deg to 5 deg. The part and full span wing configurations were also tested in ground proximity.

Morgan, H. L., Jr.↗