Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INLET FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Experimental investigation of an axial-flow-compressor inlet stage operating at transonic relative inlet Mach numbers V : rotor blade-element performance at a reduced blade angle

At a corrected speed of 1100 feet per second, the low-blade-angle rotor operated with a relative inlet Mach number of 1.2, a diffusion factor of 0.65, and an axial velocity ratio of 0.71 in the tip region (11 percent of passage height away from the outer wall). The measured minimum-loss coefficient was 0.35, and this value falls above a previous correlation of rotor losses with diffusion factor. Through a comparison with data for three other rotors, the occurrence of high losses was related to a high suction-surface Mach number. These comparisons also indicated that axial velocity ratios between 0.73 and 1.10 have no independent effect on losses.

Schwenk, Francis C↗
NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.60 to 1.05 of a Model of the "Swallow" with Outer Wing Panels Swept 75 degree with and without Power Simulations

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model with the outer wing panels swept 75 deg. has been conducted in the Langley 16-foot transonic tunnel. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. The engine nacelles incorporated swept lateral and vertical fins for aerodynamic stability and control. Jet-off data were obtained with flow-through nacelles, simulating inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained at Mach numbers from 0.60 to 1.05 through a range of angles of attack and angles of side-slip. Control characteristics were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control. The results indicate that the basic wing-body configuration becomes neutrally stable or unstable at a lift coefficient of 0.15; addition of nacelles with fins delayed instability to a lift coefficient of 0.30. Addition of nacelles to the wing-body configuration increased minimum drag from 0.0058 to 0.0100 at a Mach number of 0.60 and from 0.0080 to 0.0190 at a Mach number of 1.05 with corresponding reductions in maximum lift-drag ratio of 12 percent and 33 percent, respectively. The nacelle-fin combinations were ineffective as longitudinal controls but were adequate as directional and lateral controls. The model with nacelles and fins was directionally and laterally stable; the stability generally increased with increasing lift. Jet interference effects on stability and control characteristics were small but the adverse effects on drag were greater than would be expected for isolated nacelles.

Schmeer, James W.↗
NASA NTRS2017

Off-Design Performance of a Streamline-Traced, External-Compression Supersonic Inlet

A computational study was performed to explore the aerodynamic performance of a streamline-traced, external-compression inlet designed for Mach 1.664 at off-design conditions of freestream Mach number, angle-of-attack, and angle-of-sideslip. Serious degradation of the inlet performance occurred for negative angles-of-attack and angles-of-sideslip greater than 3 degrees. At low subsonic speeds, the swept leading edges of the inlet created a pair of vortices that propagated to the engine face. Increasing the bluntness of the cowl lip showed no real improvement in the inlet performance at the low speeds, but did improve the inlet performance at the design conditions. Reducing the inlet flow rate improved the inlet performance, but at the likely expense of reduced thrust of the propulsion system. Deforming the cowl lip for low-speed operation of the inlet increased the inlet capture area and improved the inlet performance.

distortion↗
NASA NTRS2022

High Speed Inlet Distortion Test for the X 59 Low Boom Flight Demonstrator in the NASA Glenn 8-by 6-Foot Supersonic Wind Tunnel

The Low Boom Flight Demonstrator (LBFD) High Speed Inlet Distortion Test (HSIDT) was completed in the NASA Glenn Research Center 8- by 6-Foot Supersonic Wind Tunnel (8x6 SWT) using a 9.5 percent-scale propulsion model of the X–59 to evaluate the compatibility and operability of the inlet and engine integration, focusing on the inlet dynamic effects at the engine face. The model was instrumented with steady-state and high-response total pressure probes in the conventional 40-point, equal-area array at the aerodynamic interface plane (AIP). The HSIDT successfully collected high response distortion data points for the X–59 from Mach = 0 to 1.55 for a wide range of angle-of-attack, angle-of-sideslip, and inlet flow. Analyses showed that inlet dynamic distortion and inlet planar wave (or inlet buzz) were within engine limits through most of the flight envelope. The test data showed that inlet planar wave was present at Mach 1.35 and above, at airflows between idle and maximum engine airflow. Engine throttle back will need to be limited when decelerating from supersonic flight Mach to avoid these regions of inlet planar wave. The HSIDT data was also used to compare the metric SUM40, computed from the 40 high-response AIP total pressure probes, with the metric SUM4, computed from four high-response inlet static pressure probes. The data showed that SUM4 can be used as a surrogate for SUM40 during the X–59 flight test to detect inlet planar wave.

X-59↗
NASA NTRS1984

One-dimensional unsteady modeling of supersonic inlet unstart/restart

A quasi-one-dimensional unsteady inviscid analysis of mixed-compression supersonic inlet flow is presented with emphasis on modeling of inlet unstart/restart phenomena. Numerical solution of the governing equations of motion is performed using a computationally efficient shock-capturing split-characteristics algorithm. Inlet unstart is modeled using a mass balance method which relates the expelled normal shock position ahead of the inlet cowl to the amount of spilled mass flow over the inlet housing. Comparison of computed results with experimental data for an axisymmetric inlet at a free-stream Mach number of 2.50 shows quite reasonable agreement over an entire unstart/restart transient which includes centerbody translation and retraction as well as bypass mass flow variations.

Adams, J. C., Jr.↗
NASA NTRS1984

Advanced prediction technique for the low speed aerodynamics of V/STOL aircraft. Volume 2: User's manual

A computerized prediction method known as the Vought V/STOL Aircraft Propulsive Effects computer program (VAPE) for propulsive induced forces and moments in transition and Short TakeOff and Landing (STOL) flight is improved and evaluated. The VAPE program is capable of evaluating: (1) effects of relative wind about an aircraft, (2) effects of propulsive lift jet entrainment, vorticity and flow blockage, (3) effects of engine inlet flow on the aircraft flow field, (4) engine inlet forces and moments including inlet separation, (5) ground effects in the STOL region of flight, and (6) viscous effects on lifting surfaces.

Beatty, T. D.↗
NASA NTRS1978

Estimating maximum instantaneous distortion from inlet total pressure rms measurements

In the present paper, a new mathematical model of inlet turbulence is developed by application of basic fluid dynamics and statistical concepts. The model provides an understanding of the turbulent inlet flow as well as a means of describing the flow in quantitative terms. Specifically, the maximum instantaneous distortion produced by inlet unsteady flow can be estimated by the simple measurement of rms data. Practical application of these techniques leads to a data/acquisition/reduction system that is at least one, and maybe two, orders of magnitude less expensive than conventional methods. Each data point can be reduced in terms of the mean strength of the turbulent vortices. By storing these two parameters (that are representative of the unsteady flow with the steady state information), the maximal instantaneous distortion can be reconstructed for other distortion factors at any time subsequent to the test.

Melick, H. C., Jr.↗
NASA NTRS1977

Detailed design of a quiet high flow fan

A single stage fan was designed to demonstrate the noise abatement properties of near-sonic inlet flow and long-chord stator vanes for the reduction of both upstream and downstream propagated fan source noise. It is designed to produce a pressure ratio of 1.653:1 with an adiabatic efficiency of 83.9%. The fan has a 508 mm inlet diameter with a hub/tip ratio of 0.426 and a design tip speed of 533.4 m/sec. The design inlet specific flow rate is 219.71 kg/sec sq m and there are 10 tandem stator vanes with a combined aspect ratio of 0.54.

Soltau, J. D.↗
NASA NTRS1975

Combustion intensity and distribution relation to noise generation

Experiments with several different flame holder geometries were conducted to investigate the degree to which combustion roughness can be altered by altering the flame intensity and flame distribution in a ducted combustion system. The effect of admitting primary air through a plane-slotted or a slotted-swirl vane flame holder was compared and the combustion roughness and noise was contrasted with that obtained with a closed front-end perforated can. The slotted front-end burners produced much smoother burning and less noise than the closed front-end can. No advantage was apparent with swirl vs nonswirl when approximately the same inlet flow distribution was maintained. Preheated inlet air provided somewhat smoother combustion as compared with ambient temperature air. The combustion roughness with methyl alcohol was briefly compared with that of isooctane; indications are that it burns more smoothly, but more detailed studies are needed to substantiate these indications.

Plett, E. G.↗
NASA NTRS1981

Top-mounted inlet system feasibility for transonic-supersonic fighter aircraft

The more salient findings are presented of recent top inlet performance evaluations aimed at assessing the feasibility of top-mounted inlet systems for transonic-supersonic fighter aircraft applications. Top inlet flow field and engine-inlet performance test data show the influence of key aircraft configuration variables-inlet longitudinal position, wing leading-edge extension planform area, canopy-dorsal integration, and variable incidence canards-on top inlet performance over the Mach range of 0.6 to 2.0. Top inlet performance data are compared with those or more conventional inlet/airframe integrations in an effort to assess the viability of top-mounted inlet systems relative to conventional inlet installations.

Williams, T. L.↗
NASA NTRS1988

An improved version of NCOREL: A computer program for 3-D nonlinear supersonic potential flow computations

A computer code called NCOREL (for Nonconical Relaxation) has been developed to solve for supersonic full potential flows over complex geometries. The method first solves for the conical at the apex and then marches downstream in a spherical coordinate system. Implicit relaxation techniques are used to numerically solve the full potential equation at each subsequent crossflow plane. Many improvements have been made to the original code including more reliable numerics for computing wing-body flows with multiple embedded shocks, inlet flow through simulation, wake model and entropy corrections. Line relaxation or approximate factorization schemes are optionally available. Improved internal grid generation using analytic conformal mappings, supported by a simple geometric Harris wave drag input that was originally developed for panel methods and internal geometry package are some of the new features.

Siclari, Michael J.↗