Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HYPERVELOCITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Plasma flow and fast particles in a hypervelocity accelerator - A color presentation

A new concept for particle acceleration for micrometeoroid simulation was developed at NASA Marshall Space Flight Center, using a high-density self-luminescent fast plasma flow to accelerate glass beads (with a diameter up to 1.0 mm) to velocities between 15-20 km/sec. After a short introduction to the operation of the hypervelocity range, the eight-converter-camera unit used for the photographs of the plasma flow and the accelerated particles is described. These photographs are obtained with an eight-segment reflecting pyramidal beam splitter. Wratten filters were mounted between the beam splitter and the converter tubes of the cameras. The photographs, which were recorded on black and white film, were used to make the matrices for the dye-color process, which produced the prints shown.

Igenbergs, E. B.↗

Hypervelocity impact tests on Space Shuttle Orbiter thermal protection material

Hypervelocity impact tests were conducted to simulate the damage that meteoroids will produce in the Shuttle Orbiter leading edge structural subsystem material. The nature and extent of the damage is reported and the probability of encountering meteoroids with sufficient energy to produce such damage is discussed.

Humes, D. H.↗

Spontaneous magnetic field generation in hypervelocity impacts

Hypervelocity impacts of meteoroids onto early planetary surfaces may have generated short-lived magnetic fields. The high specific power densities of the impacts, plasma production in the ejecta clouds, and the chemically layered targets of the meteoroids are analyzed in describing the evolution of the magnetic fields. Durations from about one millionth of a minute to one minute, as well as strengths up to 100 tesla, are posited for the impact-generated magnetic fields. The analogy of magnetic-field generation in laser-target experiments is also mentioned. The acquisition of shock remanence and thermoremanence by the ejecta and nearby rock following impact is discussed.

Srnka, L. J.↗

Microfractures produced by a laboratory scale hypervelocity impact into granite

Differential strain analysis and scanning electron microscopy are employed to study the microcracks produced in a granite block by shock waves from a hypervelocity impact. The anisotropy of the pre-shock cracks appears to control the orientations of the microcracks. Over the range 2 to 20 kbar, total crack porosity proves to be linearly related to shock pressure. The effect of the peak shock pressure on the width and median closure pressure of the crack spectra is also investigated. The results of the microcrack study may be useful in interpreting lunar samples.

Siegfried, R. W., II↗

Hypervelocity impact tests on Space Shuttle Orbiter RCC thermal protection material

It is noted that the Shuttle Orbiter will be more subject to meteoroid impact than previous spacecraft, due to its greater surface area and longer cumulative time in space. The Orbiter structural material, RCC, a reinforced carbon-carbon laminate with a diffused silicon carbide coating, is evaluated in terms of its resistance to hypervelocity impact. It was found that the specimens (disks with a mass of 34 g and a thickness of 5.0 mm) were cratered only on the front surface when the impact energy was 3 J or less. At 3 J, a trace of the black carbon interior was exposed. The specimens were completely penetrated when the energy was 34 J or greater.

Humes, D. H.↗

Hypervelocity impacts on Skylab IV/Apollo windows

A description is presented of some new observations of crater morphology on the Skylab IV/Apollo windows. Aluminum is detected as the only foreign component in six of the seven lined glassy pit craters so far examined by EDS analysis. The most probable source is from aluminum oxide spherules, exhaust effluent of solid fuel rocket motors. The seventh crater contains titanium which may have been derived from an impact of a chip of thermal paint. The size distribution of the lined glassy pit craters appears to be compatible with an origin by hypervelocity impacts of aluminum spherules. If the aluminum oxide spherules are in earth orbit, impact velocities largely in the range of 7 to 10 km/s should be expected. Thus, the impact velocities are well below those expected for most impacts by micrometeorites and these lower velocities may be significant in the development of the lined glassy pit craters. The results indicate that there is a significant population of man-induced micro-debris in earth orbit.

Clanton, U. S.↗

Heat-transfer distributions on biconics at incidence in hypersonic-hypervelocity He, N2, air, and CO2 flows

Laminar heat transfer rates were measured on spherically blunted, 13 deg/7 deg on axis and bent biconics (fore cone bent 7 deg upward relative to aft cone) at hypersonic hypervelocity flow conditions in the Langley Expansion Tube. Freestream velocities from 4.5 to 6.9 km/sec and Mach numbers from 6 to 9 were generated using helium, nitrogen, air, and carbon dioxide test gases, resulting in normal shock density ratios from 4 to 19. Angle of attack, referenced to the axis of the aft cone, was varied from 0 to 20 deg in 4 deg increments. The effect of nose bend, angle of attack, and real gas phenomena on heating distributions are presented along with comparisons of measurement to prediction from a code which solves the three dimensional parabolized Navier-Stokes equations.

Miller, C. G.↗

Heat-transfer distributions on biconics at incidence in hypersonic-hypervelocity He, N2, air, and CO2 flows

Laminar heat-transfer rates were measured on spherically blunted, 13 degrees/F degrees on-axis and bent biconics (fore cone bent 7 degrees upward relative to aft cone) at hypersonic-hypervelocity flow conditions in the Langley Expansion Tube. Freestream velocities from 4.5 to 6.9 km/sec and Mach numbers from 6 to 9 were generated using helium, nitrogen, air, and carbon dioxide test gases, resulting in normal shock density ratios from 4 to 19. Angle of attack, referenced to the axis of the aft cone, was varied from zero to 20 degrees in 4 degree increments. The effect of nose bend, angle of attack, and real-gas phenomena on heating distributions are presented along with comparisons of measurement to prediction from a code which solves the three-dimensional 'parabolized Navier-Stokes' equations.

Miller, C. G.↗

Hypervelocity supersonic nozzle beam source of atomic oxygen

A hypervelocity source of atomic oxygen was developed. Dissociation of molecular oxygen is accomplished by injection into a flow of helium and/or argon which has been heated in a commercial plasma torch. Atomic velocities of up to 4 kms(-1) were produced; recent improvements offer the possibility of even higher velocities. This source was utilized in studies of translational-to-vibrational energy transfer in carbon dioxide and in an investigation of the shuttle glow effect.

Freedman, A.↗

Laminar heat-transfer distributions on biconics at incidence in hypersonic-hypervelocity flows

Laminar heating distributions were measured at hypersonic-hypervelocity flow conditions on a 1.9-percent-scale model of an aeroassisted vehiclee proposed for missions to a number of planets. This vehicle is a spherically blunted, 12.84/7deg biconic with the fore-cone axis bent upward 7 deg relative to the aft-cone axis to provide selftrim capability. Also tested was a straight biconic (i.e., without nose bend) with the same nose radius and half-angles as the bent-nose biconic. These measurements were made in the Langley Expansion Tube at free-stream velocities from 4.5 to 6.9 km/sec and Mach numbers from 6.0 to 9.0 with helium, nitrogen, air, and carbon dioxide test gases. The range of calculated thermochemical equilibrium normal-shock density ratios for these four test gases was 4 to 19. Angles of attack, referenced to the aft-cone, varied from 0 to 20 deg. Heating distributions predicted with a parabolized Navier-Stokes (PNS) code were compared with measurement for helium and air test gases. Measured windward and leeward heating levels were generally underpredicted by the PNS code for both test gases, and agreement was poorer on the leeward side than on the windward side.

Miller, C. G., III↗

Hypervelocity impact investigations and meteoroid shielding experience related to Apollo and Skylab

Generic hypervelocity impact related topics and specific Apollo/Skylab related investigations are reviewed. Cratering and spallation mechanisms and the relationships between the effecting physical parameters are discussed. Design and material requirements for meteoroid shielding structures are also addressed. Penetration resistance and failure mode studies for Apollo/Skylab components are reviewed.

Cour-Palais, B. G.↗

Magnetic field amplification and generation in hypervelocity meteoroid impacts with application to lunar paleomagnetism

A one-dimensional numerical model for the expansion of impact-produced vapor clouds is used to investigate magnetic field generation mechanisms in events such as meteor collisions with the moon. The resulting cloud properties, such as ionization fraction, electrical conductivity, radial expansion velocity, mass density, and energy density are estimated. The model is initiated with the peak shock states and pressure thresholds for incipient and complete vaporization of anorthosite lunar surface materials by iron and GA composition meteorites. The expansion of the spherical gas cloud into a vacuum was traced with a one-dimensional explicit lagrangian hydrodynamic code. The hypervelocity impact plasmas produced are found to be significant in the amplitudes and orientations of the magnetic fields generated. An ambient magnetic field could have been provided by the core dynamo, which would have interacted with the expanding plasmas and formed induced paleomagnetic fields. Several other field-contribution mechanisms are discussed and discarded as potential remanent magnetism contributors.

Hood, L. L.↗

Chemical and thermal nonequilibrium heat transfer analysis for hypervelocity, low Reynolds number flow

Chemical and thermal nonequilibrium phenomena are studied in the stagnation region of a hypervelocity blunt body. This investigation is motivated by the need to predict the heat transfer rate to the leading edge of Aeromaneuvering Orbital Transfer Vehicles. Flight speeds of approximately 10 km/s at altitudes of approximately 80 km are considered for body radii of 1 to 50 cm. The analysis is based on continuum theory and is applicable to the viscous-layer and incipient-merged-layer rarefied-flow regimes. A two-species, two-temperature gas model is assumed. Comparisons are made with previous theories, experimental data, and results based on the thermodynamic equilibrium assumption. The equation accounting for vibrational nonequilibrium is presented and its effects on flow properties are discussed. Parameters which require further investigation are identified. Preliminary results indicate that the inclusion of vibrational relaxation has little effect on heat transfer rate for a catalytic surface. However, vibrational nonequilibrium may increase the heat transfer rate to a noncatalytic surface, depending on the degree of nonequilibrium.

Brown, K. G.↗

Necessary conditions for maximax problems with application to aeroglide of hypervelocity vehicles

This paper presents the necessary conditions for solving Chebyshev minimax (or maximax) problems with bounded control. The jump conditions obtained are applicable to problems with single or multiple maxima. By using Contensou domain of maneuverability, it is shown that when the maxima are isolated single points the control is generally continuous at the jump point in the minimax problems and discontinuous in the maximax problems in which the first time derivative of the maximax function contains the control variable. The theory is applied to the problem of maximizing the flight radius in a closed circuit glide of a hypervelocity vehicle and to a maximax optimal control problem in which the control appears explicitly with the first time derivative of the maximax function.

Vinh, N. X.↗

A mixing augmentation technique for hypervelocity scramjets

The paper discusses mixing problems in hypervelocity scramjet combustors. Techniques for providing turbulence and/or mixing enhancement are described. One such technique, the oscillating shock interaction, is studied numerically and options for producing oscillatory shock waves for mixing augmentation in scramjet combustors are discussed.

Kumar, A.↗

Hypervelocity Technology (HVT) crew escape

Conceptual designs are being investigated for escape systems applicable to hypervelocity technology class aerospace vehicles. The concepts selected for further development will provide survivable escape and recovery throughout all phases of flight. Sixteen conceptual escape systems were identified, of which two were viable. The study vehicles included a horizontally launched vehicle (HLV) and a vertically launched vehicle (VLV). Computer-aided design models of the candidate escape systems were developed. State-of-the-art or near-term enabling technologies were identified in such areas as propulsion, life support, thermal protection, and deceleration.

Jines, Lanny A.↗

Oblique hypervelocity impact response of dual-sheet structures

The results of a continuing investigation of the phenomena associated with the oblique hypervelocity impact of spherical projectiles onto multi-sheet aluminum structures are given. A series of equations that quantitatively describes these phenomena is obtained through a regression of experimental data. These equations characterize observed ricochet and penetration damage phenomena in a multi-sheet structure as functions of geometric parameters of the structure and the diameter, obliquity, and velocity of the impacting projectile. Crater damage observed on the ricochet witness plates is used to determine the sizes and speeds of the ricochet debris particles that caused the damage. It is observed that the diameter of the most damaging ricochet debris particle can be as large as 40 percent of the original particle diameter and can travel at speeds between 24 percent and 36 percent of the original projectile impact velocity. The equations necessary for the design of shielding panels that will protect external systems from such ricochet debris damage are also developed. The dimensions of these shielding panels are shown to be strongly dependent on their inclination and on their circumferential distribution around the spacecraft.

Schonberg, William P.↗

Further investigations of oblique hypervelocity impact phenomena

The results of a continuing investigation of the phenomena associated with the oblique hypervelocity impact of spherical projectiles onto multi-sheet aluminum structures are described. A series of equations that quantitatively describes these phenomena is obtained through a regression of experimental data. These equations characterize observed ricoshet and penetration damage phenomena in a multi-sheet structure as functions of the geometric parameters of the structure and the diameter, obliquity, and velocity of the impacting projectile. Crater damage observed on the ricochet witness plates is used to determine the sizes and speeds of the ricochet debris particles that caused the damage. It is shown that, in general, the most damaging ricochet debris particle is approximately 0.25 cm (0.10 in) in diameter and travels at the speed of approximately 2.1 km/sec (6,890 ft/sec). The equations necessary for the design of shielding panels that will protect external systems from such ricochet debris damage are also developed. The dimensions of these shielding panels are shown to be strongly dependent on their inclination and on their circumferential distribution around the spacecraft. It is concluded that obliquity effects of high-speed impacts must be considered in the design of any structure exposed to the meteoroid and space debris environment.

Schonberg, William P.↗