Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HARDENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Early age strength increase of fly ash blended cement by a ternary hardening accelerating admixture

The applicability of a combination of sodium thiocyanate (NaSCN), diethanolamine (DEA) and glycerol (Gly) with small dosages as a ternary hardening accelerating admixture for fly ash blended cement (OPC-FA) was studied. The ternary admixture induced higher early and later age mortar strength at both low (5 °C) and normal (20 °C) temperature. Despite used in lower dosage the ternary admixture led to higher strength of the investigated OPC-FA system than other chemicals (e.g. sodium sulfate). Results obtained from isothermal calorimetry, thermogravimetric analysis (TGA) and X-ray diffraction (XRD) showed that the ternary admixture accelerated the cement hydration and increased the amount of AFm (notably calcium hemicarboaluminate hydrate) in the hydration products. A synergistic effect between the three components of the accelerator on the hydration of OPC-FA system was observed.

36 MATERIALS SCIENCE↗

Tensile performance of sustainable Strain-Hardening Cementitious Composites with hybrid PVA and recycled PET fibers

Highlights: • SHCCs with hybrid PVA/PET fibers are theoretically and experimentally studied. • A semi-empirical way to predict strain capacity of hybrid-fiber SHCCs is proposed. • The impacts of PET fiber surface treatment and curing time are explored. • SHCCs achieve satisfactory performance even 50% PVA fibers are replaced by PET fibers. • Using PET fibers in SHCCs effectively reduces material cost and environmental impact. - Abstract: Strain-Hardening Cementitious Composite (SHCC) is a type of advanced construction material that can enhance the resiliency and durability of structures. However, the high cost of the constituents limits the wide application of SHCCs. To reduce the material cost and improve the sustainability, this study explores the potential of replacing commonly-used polyvinyl alcohol (PVA) fibers by recycled polyethylene terephthalate (PET) fibers. The potential of fiber hybridization was first evaluated using micromechanical modeling, and the ultimate tensile strain of hybrid-fiber SHCCs was estimated using a semi-empirical method. Then the tensile performance of SHCCs after standard curing and accelerated aging was experimentally evaluated, and the crack pattern development with increasing tensile strain was recorded. Satisfactory mechanical performance can be achieved even when 50% of PVA fibers are replaced by recycled PET fibers with surface treatment. In addition, using recycled PET fibers in SHCCs can significantly reduce the material cost and environmental impact.

36 MATERIALS SCIENCE↗

On the use of limestone calcined clay cement (LC3) in high-strength strain-hardening cement-based composites (HS-SHCC)

Highlights: • Use of LC{sup 3} slightly reduces flowability and shortens the setting time of fresh matrices. • Highly polymerized C-A-S-H gel and abundant ettringite benefit flexural strength of LC{sup 3}-matrices. • Use of LC{sup 3} enhances the bond strength between fiber and high-strength matrix. • LC{sup 3}-based HS-SHCC yields similar flexural performance as the composite with Portland cement. High-strength strain-hardening cement-based composites (HS-SHCC) demonstrate excellent mechanical and durability properties. However, high cement content typical to HS-SHCC results not only in high carbon footprint, but also in excessive hydration heat and severe autogenous shrinkage. In this investigation, Limestone Calcined Clay Cement (LC{sup 3}) was used to produce sustainable HS-SHCC. The LC{sup 3} substitution resulted in higher energy consumption during mixing and in shorter setting times of the fresh, plain matrices. Although the LC{sup 3} substitution slightly reduced the compressive strength, the formation of highly polymerized C-A-S-H gel and abundant ettringite benefited the flexural strength of the plain matrices. Additionally, single-fiber pullout experiments showed that the use of LC{sup 3} led to increased fiber-matrix bond strength and pullout energy. Finally, the replacement of Portland cement by LC{sup 3} resulted in HS-SHCC with similar mechanical performance to the reference composite, indicating a high potential for using LC{sup 3} in high-performance cement-based composites.

36 MATERIALS SCIENCE↗

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

A novel Cu-added medium-Mn steel with a chemical composition of Fe–0.27C–9.1Mn–1.86Al–3.3Cu (wt.%) was designed and subjected to intercritical annealing (IA) temperature range from 620 °C to 680 °C for 1 h. The ultimate tensile strength (UTS) increases and the yielding strength (YS) decreases with the IA temperature increasing. The YS of 824 MPa, UTS of 1222 MPa, total elongation (TE) of 55%, and product of strength and elongation (PSE) of 67.2 GPa·% are achieved after IA at 660 °C. Transmission electron microscopy confirmed that Cu-rich nanoparticles precipitate in the ferrite. The in-situ high-energy X-ray diffraction (HE-XRD) experiments show that at the beginning of plastic deformation, both austenite and ferrite bear the applied load. The load is mainly undertaken by martensite with effective transformation-induced plasticity (TRIP) effect triggered. The YS of ferrite is significantly higher than that of austenite. The individual contribution of solid solution strengthening, grain refinement strengthening, dislocation strengthening, and precipitation strengthening in ferrite and austenite is analyzed. The discrepancy between the YS of ferrite and austenite is mainly attributed to the precipitation strengthening due to the Cu-rich nanoparticles precipitation. The moderate mechanical stability and the collaboration of TRIP and twinning-induced plasticity (TWIP) effects of austenite contributed to the enhanced strain hardening capability and resulted in large ductility.

36 MATERIALS SCIENCE↗

Low Temperature Age Hardening in U-13 at.% Nb: An Atom Probe Tomography Study

Low temperature aging (<350 C) of U-13 at.% Nb martensite results in increased strength levels accompanied by significant ductility loss. To determine the decomposition mechanism(s) responsible for these mechanical property changes, atom probe tomography was used to examine the niobium and impurity distributions after aging at 200 or 300 C for times ranging from 2 h to 70 days. No patterns of niobium or impurity atoms were observed that would indicate segregation to the martensitic twin interfaces, making this hardening mechanism unlikely. Phase separation into roughly equiaxed regions of high and low niobium concentration was clearly observed after aging at 300 C for 70 days. However, only subtle niobium concentration changes were observed after aging at 200 C relative to the as-quenched condition, indicating that conventional phase separation is an unlikely explanation for the dramatic mechanical property changes at 200 C. Therefore, consideration of aging mechanisms other than segregation and phase separation may be warranted.

36 MATERIALS SCIENCE↗

Comparison of hardening and microstructures of ferritic/martensitic steels irradiated with fast neutrons and dual ions

Ferritic/martensitic steels T91 and HT9 were irradiated with neutrons (BOR-60 reactor) and dual ions (9 MeV Fe 3+ and 3.42 MeV energy degraded He 2+ ) from 369 to 520 °C and damage levels of 16.6 to 72 dpa to quantify the possibility of using ion irradiation to simulate neutron irradiation in terms of microstructures and mechanical properties. Nanoindentation testing was performed to obtain the bulk equivalent hardness of the dual-ion irradiated samples. For the neutron irradiated samples, both nanoindentation and Vickers hardness testing were conducted. Transmission Electron Microscopy (TEM) characterizations of the cavities, dislocation loops and precipitates were conducted to account for the strengthening contribution of each microstructure element. The good agreement between the microstructure-predicted (dispersed barrier hardening) and measured strength of the irradiated specimens demonstrated the accuracy of the strengthening model and the nanoindentation tests. Furthermore, the comparison of mechanical property and microstructure changes in ion and neutron irradiated structural materials indicated that ion irradiation replicated many neutron irradiation features. However, a single 70 °C temperature shift is insufficient to match all complex microstructures of neutron vs. ion irradiation over the irradiation temperature range of 369–520 °C.

36 MATERIALS SCIENCE↗

Effect of reinforcing particle type on morphology and age-hardening behavior of Al–4.5 wt.% Cu based nanocomposites synthesized through mechanical milling

The effects of reinforcing particle type (SiC and TiC) on morphology and precipitation hardening behavior of Al–4.5%Cu based nanocomposites synthesized via mechanical milling were investigated in the current work. In order to study the microstructure and morphology of mechanically milled powder, X-ray diffraction technique, scanning electron microscopy and high resolution transmission electron microscopy were utilized. Results revealed that at the early stages of mechanical milling, when reinforcing particles are polycrystal, the alloying process is enhanced more in the case of using the TiC particles as reinforcement. But, at the final stages of mechanical milling, when reinforcing particles are single crystal, the alloying process is enhanced more in the case of using the SiC ones. Transmission electron microscopy results demonstrated that Al–4.5 wt.%Cu based nanocomposite powders were synthesized and confirmed that the mutual diffusion of aluminum and copper occurs through the interfacial plane of (200). The hardness results showed that not only does introducing 4 vol.% of reinforcing particles (SiC or TiC) considerably decrease the porosity of the bulk composite samples, but also it approximately doubles the hardness of Al–4.5 wt.%Cu alloy (53.4 HB). Finally, apart from TEM and scanning electron microscopy observation which are localized, a decline in hardness in the TiC and SiC contained samples, respectively, after 1.5 and 2 h aging time at 473 K proves the fact that the size of SiC particles is smaller than the size of the TiC ones. - Highlights: ► HRTEM results show mutual diffusion of Al and Cu occurs through the (200) planes. ► TiC particles enhance alloying process more than the SiC ones at the early stages of MM. ► SiC particles enhance alloying process more than the TiC ones at the final stages of MM.

36 MATERIALS SCIENCE↗

Age hardening and creep resistance of cast Al–Cu alloy modified by praseodymium

The effects of praseodymium on age hardening behavior and creep resistance of cast Al–Cu alloy were investigated. The results indicated that praseodymium facilitated the formation of the θ′ precipitates during the age process and improved the hardness of the Al–Cu alloy. Besides, praseodymium resulted in the formation of the Al{sub 11}Pr{sub 3} phase in the grain boundaries and among the dendrites of the modified alloy. Because of the good thermal stability of Al{sub 11}Pr{sub 3} phase, it inhibits grain boundary migration and dislocation movement during the creep process, which contributes to the improvement in the creep resistance of the modified alloy at elevated temperatures. - Highlights: • Pr addition enhances the hardness and creep resistance of the Al–Cu alloy. • Pr addition facilitates the formation of the θ′ precipitates. • Pr addition results in the formation of the Al11Pr3 phase in the Al–Cu alloy.

36 MATERIALS SCIENCE↗

Initial precipitation and hardening mechanism during non-isothermal aging in an Al–Mg–Si–Cu 6005A alloy

The characterization of precipitation and hardening mechanism during non-isothermal aging had been investigated using high resolution transmission electron microscopy for an Al–Mg–Si–Cu 6005A alloy. It was proposed that the needle-shaped β″ precipitates with a three-dimension coherency strain-field and an increased number density in the Al matrix provided the maximum strengthening effect for the Al–Mg–Si–Cu 6005A alloy. Simultaneously, it was also found that the formation and evolution of clusters in the early precipitation were associated with the vacancy binding energy, during which Si atoms played an important role in controlling the numbers density of Mg/Si co-clusters, and the excess Si atoms provided the increased number of nucleation sites for the subsequent precipitates to strengthen and improve the precipitation rate. Finally, based on the experimental observation and theoretical analysis, the precipitation sequence during the early precipitation in the Al–Mg–Si–Cu 6005A alloy was proposed as: supersaturated solid solution → Si-vacancy pairs, Mg-vacancy pairs and Mg clusters → Si clusters, and dissolution of Mg clusters → Mg atoms diffusion into the existing Si clusters → Mg/Si co-clusters → GP zone. - Highlights: • β″ precipitates provide the maximum strengthening effect for the 6005A alloy. • Si atoms play an important role in controlling the numbers of Mg/Si co-clusters. • The early aging sequence is deduced based on the solute-vacancy binding energy.

36 MATERIALS SCIENCE↗

Effects of quench rate and natural ageing on the age hardening behaviour of aluminium alloy AA6060

Quench sensitivity in Al–Mg–Si alloys has been largely attributed to the solute loss at the heterogeneous nucleation sites, primarily dispersoids, during slow cooling after extrusion. As such, the number density of dispersoids, the solute type and concentration are considered to be the key variables for the quench sensitivity. In this study, quench sensitivity and the influence of natural ageing in a lean Al–Mg–Si alloy, AA6060, which contains few dispersoids, have been investigated by hardness measurement, thermal analysis, transmission electron microscopy (TEM) and positron annihilation lifetime spectroscopy (PALS). It is shown that the quench sensitivity in this alloy is associated with the degree of supersaturation of vacancies after cooling. Due to vacancy annihilation and clustering during natural ageing, the quench sensitivity is more pronounced after a short natural ageing time (30 min) compared to a longer natural ageing time (24 h). Therefore, prolonged natural ageing not only leads to an increase in hardness, but can also have a positive effect on the quench sensitivity of lean Al–Mg–Si alloys. - Highlights: • Significant quench sensitivity observed in AA6060 alloy after 30 min natural ageing • Prolonged natural ageing increased hardness and reduced QS. • Low dispersoid density leads to insignificant QS from non-hardening precipitates. • Vacancy supersaturation identified as a contributor to QS.

36 MATERIALS SCIENCE↗

Localized plastic deformation and hardening in laser shock peened Inconel alloy 718SPF

Highlights: • The plastic strain in LSP-treated Inconel 718 alloy was characterized using EBSD. • LSP increases the low angle misorientations in the near-surface region, indicating the extend of plastic strain. • The near-surface plastic strain leads to an increase in local hardness and yield stress. - Abstract: Localized plastic deformation and hardening was studied in laser shock peened (LSP) Inconel 718 SPF (Super plastic forming), a fine grained Ni-Base superalloy, using electron backscatter diffraction (EBSD), nanoindentation, and micro pillar compression testing. 718SPF samples were LSP-treated with two different laser power densities. After LSP, the plastic deformation is manifested as increase in the fraction of low angle misorientations and the formation of sub-grain boundaries. EBSD was used to study plastic deformation as a function of distance from the peened surface for different laser intensities. Different approaches like image quality mapping and local misorientations analysis were used to study the in-depth distribution of the plastic strain. Results show that EBSD is effective in the qualitative characterization of localized plastic strain of the materials subjected to LSP.

36 MATERIALS SCIENCE↗

Austenite stability and M2C carbide decomposition in experimental secondary hardening ultra-high strength steels during high temperature austenitizing treatments

The present study deals with the austenite stability and M{sub 2}C carbide decomposition in three secondary hardening ultra-high strength (SHUHS) steels with varying levels of Cr and Mo (2Cr-1Mo, 2Cr-3Mo and 5Cr-5Mo) investigated using Vicker's hardness, optical and electron microscopy. These steels were subjected to high temperature austenitizing treatments at 1000, 1050, 1100 and 1150 °C. It has been established that increasing both Cr and Mo to 5 wt% as well as increasing the austenitizing temperature in this class of SHUHS steels is stabilizing the austenite such that almost 100% austenite is produced upon oil quenching. Further, higher Cr and Mo is also found to influence the stability of metastable M{sub 2}C carbide formed during processing of the steels. While the M{sub 2}C carbide in 2Cr-3Mo steel remained untransformed, it was found to transform partially to M{sub 6}C during austenitization of 5Cr-5Mo steel. Hardness measurements on these steels revealed that hardness is relatively insensitive to austenitizing temperature in 2Cr-1Mo steel, decreased in 2Cr-3Mo and decreased more drastically in 5Cr-5Mo steel with austenitizing temperature. This dependence has been correlated to the influence of composition on M{sub s} temperature and hence on retention of austenite as well as primary carbides. The experimental results were compared against theoretical calculations using ThermoCalc, which predict the presence of only M{sub 6}C in both 2Cr-3Mo and 5Cr-5Mo steels. The apparent discrepancy between theoretical and experimental observations has been correlated to kinetic factors.

36 MATERIALS SCIENCE↗

Austenite and precipitation in secondary-hardening ultra-high-strength stainless steel

Highlights: • Austenite and precipitation in Ferrium S53 steel were analyzed. • Austenite decreased to less than 5% after cryogenic treatment and tempering. • M{sub 2}C carbide could segregate inside martensite lath or in the larger parallel microstructure. - Abstract: Ferrium S53 is a new secondary-hardening ultra-high-strength stainless steel, with more Cr than other Co-Ni ultra-high-strength steels. Austenite has a great effect on the fracture toughness of this metal, and the carbides that are precipitated are the main strengthening phase of Ferrium S53 steel; in this study, its microstructural changes during heat treatment were observed and analyzed by X-ray diffraction (XRD), Optical microscope (OM), SEM, and transmission electron microscopy (TEM). About 40.85% retained austenite in the quenched sample is decreased to less than 5% after cryogenic treatment and tempering. In the final sample, block austenite is retained austenite, and film austenite around 5 nm in width is reverted austenite. Inside the martensite lath, parallel twin-like structures are actually segregated M{sub 2}C precipitates, and most of them are smaller than 20 nm. These precipitates can be aggregated into a several-micron-long parallel zonal microstructure.

36 MATERIALS SCIENCE↗

Hot deformation characteristics of AZ80 magnesium alloy: Work hardening effect and processing parameter sensitivities

Isothermal compression experiment of AZ80 magnesium alloy was conducted by Gleeble thermo-mechanical simulator in order to quantitatively investigate the work hardening (WH), strain rate sensitivity (SRS) and temperature sensitivity (TS) during hot processing of magnesium alloys. The WH, SRS and TS were described by Zener-Hollomon parameter (Z) coupling of deformation parameters. The relationships between WH rate and true strain as well as true stress were derived from Kocks-Mecking dislocation model and validated by our measurement data. The slope defined through the linear relationship of WH rate and true stress was only related to the annihilation coefficient Ω. Obvious WH behavior could be exhibited at a higher Z condition. Furthermore, we have identified the correlation between the microstructural evolution including β-Mg17Al12 precipitation and the SRS and TS variations. Intensive dynamic recrystallization and homogeneous distribution of β-Mg17Al12 precipitates resulted in greater SRS coefficient at higher temperature. The deformation heat effect and β-Mg17Al12 precipitate content can be regarded as the major factors determining the TS behavior. At low Z condition, the SRS becomes stronger, in contrast to the variation of TS. The optimum hot processing window was validated based on the established SRS and TS values distribution maps for AZ80 magnesium alloy.

36 MATERIALS SCIENCE↗

Precipitation hardening of laser powder bed fusion Ti-6Al-4V

Here, the laser powder bed fusion (PBF-L) additive manufacturing (AM) community has dedicated significant efforts into process optimization and control for defect-free Ti-6Al-4V. As defects become less of an issue for PBF-L Ti-6Al-4V, the processing-structure-properties (PSP) relationships between AM microstructures can now be explored to optimize mechanical properties. Lower temperature aging treatments around 550 °C in wrought Ti-6A-4V have been historically understood to precipitation harden the α phase with an ordered, hexagonal close packed (HCP) α 2 phase. The α 2 phase existed as nanoscale Ti 3 Al precipitates coherent with the parent α phase. The goal of the present investigation was to implement a vacuum heat treatment of 545 °C for 100 hours on PBF-L Ti-6Al-4V. This vacuum heat treatment took place after an initial hot isostatic pressure (HIP) treatment that decomposed the as-built, martensitic microstructure. The vacuum aging successfully produced nanoscale precipitates of α 2 phase within α-laths, confirmed via atom probe tomography (APT). Microstructural-length scale and quasi-static mechanical properties were investigated by nanoindentation and uniaxial tensile tests of miniaturized test specimens. Given the sensitivity of Ti-6Al-4V mechanical properties to small changes in chemistry, all test specimens originated from the same build. The α 2 precipitation resulted in significantly harder α-laths (≈ 2 GPa) as measured via nanoindentation, as well as a relative yield and ultimate tensile strength increase of 60 MPa and 38 MPa, respectively. Analysis of Variance (ANOVA) of the datasets revealed no statistical differences in total elongation between the HIPed and HIPed + aged specimens, indicative of the aging treatment producing a net benefit of strength with no loss in ductility.

36 MATERIALS SCIENCE↗

Revealing cyclic hardening mechanism of a TRIP steel by real-time in situ neutron diffraction

Real-time in situ neutron diffraction was performed on a transformation-induced plasticity (TRIP) steel under cyclic loading at room temperature. By Rietveld refinement and single peak analysis, the volume fraction and average stress estimates as well as dislocation density of individual phases (austenite and martensite phase) were derived. The results reveal that the volume fraction of martensite phase, instead of individual phase strengthening, should be accounted for the remarkable secondary cyclic hardening.

Austenitic steels↗

Optimizing Earthquake Nowcasting With Machine Learning: The Role of Strain Hardening in the Earthquake Cycle

Abstract Nowcasting is a term originating from economics, finance, and meteorology. It refers to the process of determining the uncertain state of the economy, markets or the weather at the current time by indirect means. In this paper, we describe a simple two‐parameter data analysis that reveals hidden order in otherwise seemingly chaotic earthquake seismicity. One of these parameters relates to a mechanism of seismic quiescence arising from the physics of strain‐hardening of the crust prior to major events. We observe an earthquake cycle associated with major earthquakes in California, similar to what has long been postulated. An estimate of the earthquake hazard revealed by this state variable time series can be optimized by the use of machine learning in the form of the Receiver Operating Characteristic skill score. The ROC skill is used here as a loss function in a supervised learning mode. Our analysis is conducted in the region of 5° × 5° in latitude‐longitude centered on Los Angeles, a region which we used in previous papers to build similar time series using more involved methods (Rundle & Donnellan, 2020, https://doi.org/10.1029/2020EA001097 ; Rundle, Donnellan et al., 2021, https://doi.org/10.1029/2021EA001757 ; Rundle, Stein et al., 2021, https://doi.org/10.1088/1361-6633/abf893 ). Here we show that not only does the state variable time series have forecast skill, the associated spatial probability densities have skill as well. In addition, use of the standard ROC and Precision (PPV) metrics allow probabilities of current earthquake hazard to be defined in a simple, straightforward, and rigorous way.

58 GEOSCIENCES↗

Development of a Beam Hardening Correction Method for a microCT Scanner Prototype

The radiographic projections acquired with a microCT were simulated and then corrected for beam hardening effects using the linearized signal to equivalent thickness (LSET) method. This procedure requires a calibration signal for each pixel obtained from a set of images with filters of increasing thickness. The projections are corrected by converting the signal to an equivalent thickness using interpolation over the calibration images. The method was validated using simulated projections of different phantoms. Two calibration sets were simulated using aluminum and water filters of thicknesses ranging from 0 to 5 mm and from 0 to 50 mm, respectively. A simulation of the phantoms' projections using a monoenergetic beam was also obtained to establish the relative intensity on the tomographic images when no cupping artifacts are present. Comparison between corrected and uncorrected tomographic images shows that the LSET method effectively corrects the cupping artifact. Streaking artifacts correction with the LSET method shows better results than with the traditional water correction method. Results are independent of the two calibration materials used.

62 RADIOLOGY AND NUCLEAR MEDICINE↗