Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRAPHENE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Single layer graphene protective layer on GaAs photocathodes for spin-polarized electron source

GaAs-based photocathodes are the primary choice for polarized electron sources, commonly used in polarized electron microscopes and polarized positron sources. GaAs photocathodes are typically activated with cesium and oxygen, which are highly reactive and require an ultra-high vacuum (⁠~ 10 -11 Torr or lower) to operate reliably, resulting in substantial operational difficulties. A short exposure to a mediocre vacuum results in an instantaneous loss of cathode quantum efficiency (QE) due to the chemical reaction of the active layer with residual gas molecules or back-bombardment ions during operation. Covering the GaAs cathode with a 2D material, such as monolayer graphene, could provide protection against such damage due to the inhibition of chemical reactions with residual gas molecules. In this paper, we have incorporated a method known as intercalation to pass the active material underneath the graphene and activate the superlattice GaAs/GaAsP (SL-GaAs) photocathode. X-ray photoelectron spectroscopy, low-energy electron microscopy, and Mott scattering measurements were performed to evaluate the formation of the photocathode under graphene, as well as its spectral response and electron spin polarization. Our results demonstrate that the successful activation of the SL-GaAs photocathode with a graphene protection layer is achieved with a moderate QE. Furthermore, we found that the electron spin polarization of the cathode with a surface protection layer is higher than the conventional cathode without a protection layer.

2D materials↗
DOE OSTI2021

Quantum-Well Bound States in Graphene Heterostructure Interfaces

We present experimental evidence of electronic and optical interlayer resonances in graphene van der Waals heterostructure interfaces. Using the spectroscopic mode of a low-energy electron microscope (LEEM), we characterized these interlayer resonant states up to 10 eV above the vacuum level. Compared with nontwisted, AB-stacked bilayer graphene (AB BLG), an ≈ 0.2 Å increase was found in the interlayer spacing of 30° twisted bilayer graphene (30°-tBLG). In addition, we used Raman spectroscopy to probe the inelastic light-matter interactions. A unique type of Fano resonance was found around the D and G modes of the graphene lattice vibrations. This anomalous, robust Fano resonance is a direct result of quantum confinement and the interplay between discrete phonon states and the excitonic continuum.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Elastic Screening of Pseudogauge Fields in Graphene

Lattice deformations in graphene couple to the low-energy electronic degrees of freedom as effective scalar and gauge fields. Using molecular dynamics simulations, we show that the optical component of the displacement field, i.e., the relative motion of different sublattices, contributes at equal order as the acoustic component and effectively screens the pseudogauge fields. In particular, we consider twisted bilayer graphene and corrugated monolayer graphene. In both cases, optical lattice displacements significantly reduce the overall magnitude of the pseudomagnetic fields. For corrugated graphene, optical contributions also reshape the pseudomagnetic field and significantly modify the electronic bands near charge neutrality. Previous studies based on continuum elasticity, which ignores this effect, have therefore systematically overestimated the strength of the strain-induced pseudomagnetic field. Furthermore, our results have important consequences for the interpretation of experiments and design of straintronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Defect-induced magnetism and Yu-Shiba-Rusinov states in twisted bilayer graphene

Atomic defects have a significant impact on the low-energy properties of graphene systems. By means of first-principles calculations and tight-binding models we provide evidence that chemical impurities modify both the normal and the superconducting states of twisted bilayer graphene. Here, a single hydrogen atom attached to the bilayer surface yields a triple-point crossing, whereas self-doping and threefold symmetry breaking are created by a vacant site. Both types of defects lead to time-reversal symmetry breaking and the creation of local magnetic moments. Hydrogen-induced magnetism is found to exist also at the doping levels where superconductivity appears in magic-angle graphene superlattices. As a result, the coexistence of superconducting order and defect-induced magnetism yields in-gap Yu-Shiba-Rusinov excitations in magic-angle twisted bilayer graphene.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Controlling selective nucleation and growth of dysprosium islands on graphene by metal intercalation

We report metal intercalation is an effective method to modify the physical and chemical properties of low-dimensional systems such as epitaxial graphene. Here, we show that the nucleation and growth of metal nanostructures on epitaxial graphene on SiC(0001) can be dramatically changed by metal intercalation. Using scanning tunneling microscopy experiments, we demonstrate that dysprosium (Dy) metal islands are selectively nucleated on the area with Dy intercalation under both graphene and carbon buffer layers, while the adjacent area with only buffer layer intercalated remains relatively bare. Using first-principles calculations based on density functional theory, we show that adsorption of Dy adatom on the preferred nucleation area is energetically more favorable than on other areas. Moreover, changes in the electronic structure and the interlayer spacing upon Dy intercalation obtained from our calculations are also consistent with experimental observations. Our results indicate that metal intercalation is a promising way to manipulate the interaction between graphene and deposited adatoms.

2-dimensional systems↗
DOE OSTI2019

Electron-Stimulated Desorption of Cesium Atoms from Graphene to Iridium Intercalated and not Intercalated with Cesium

The processes of electron-stimulated desorption of neutral cesium atoms from graphene to iridium are studied in the cases in which the graphene layer is or is not intercalated with cesium. It was found that there are two peaks in the kinetic energy distributions of desorbed neutral cesium atoms: a high-energy peak at 0.36 eV and a low-energy one at 0.13 eV. The high-energy peak is observed in both cases and is associated with the excitation of the 2s core levels of carbon. The low-energy peak is observed only in the absence of intercalation and is associated with the excitation of the 4f and 5p core levels of iridium. A model describing the processes of electron-stimulated desorption of cesium atoms from a graphene surface on iridium is proposed, and a conclusion is made that graphene on iridium behaves in these processes as a dielectric.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Dynamics of a Three-Component Delocalized Nonlinear Vibrational Mode in Graphene

The dynamics of a three-component nonlinear delocalized vibrational mode in graphene is studied with molecular dynamics. This mode, being a superposition of a root and two one-component modes, is an exact and symmetrically determined solution of nonlinear equations of motion of carbon atoms. The dependences of a frequency, energy per atom, and average stresses over a period that appeared in graphene are calculated as a function of amplitude of a root mode. We showed that the vibrations become periodic with certain amplitudes of three component modes, and the vibrations of one-component modes are close to periodic one and have a frequency twice the frequency of a root mode, which is noticeably higher than the upper boundary of a spectrum of low-amplitude vibrations of a graphene lattice. The data obtained expand our understanding of nonlinear vibrations of graphene lattice.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

In Situ Study of the Impact of Aberration-Corrected Electron-Beam Lithography on the Electronic Transport of Suspended Graphene Devices

The implementation of aberration-corrected electron beam lithography (AC-EBL) in a 200 keV scanning transmission electron microscope (STEM) is a novel technique that could be used for the fabrication of quantum devices based on 2D atomic crystals with single nanometer critical dimensions, allowing to observe more robust quantum effects. In this work we study electron beam sculpturing of nanostructures on suspended graphene field effect transistors using AC-EBL, focusing on the in situ characterization of the impact of electron beam exposure on device electronic transport quality. When AC-EBL is performed on a graphene channel (local exposure) or on the outside vicinity of a graphene channel (non-local exposure), the charge transport characteristics of graphene can be significantly affected due to charge doping and scattering. While the detrimental effect of non-local exposure can be largely removed by vigorous annealing, local-exposure induced damage is irreversible and cannot be fixed by annealing. We discuss the possible causes of the observed exposure effects. Our results provide guidance to the future development of high-energy electron beam lithography for nanomaterial device fabrication.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Noncured Graphene Thermal Interface Materials for High-Power Electronics: Minimizing the Thermal Contact Resistance

We report on experimental investigation of thermal contact resistance, RC, of the noncuring graphene thermal interface materials with the surfaces characterized by different degree of roughness, Sq. It is found that the thermal contact resistance depends on the graphene loading, ξ, non-monotonically, achieving its minimum at the loading fraction of ξ ~15 wt%. Decreasing the surface roughness by Sq~1 μm results in approximately the factor of ×2 decrease in the thermal contact resistance for this graphene loading. The obtained dependences of the thermal conductivity, KTIM, thermal contact resistance, RC, and the total thermal resistance of the thermal interface material layer on ξ and Sq can be utilized for optimization of the loading fraction of graphene for specific materials and roughness of the connecting surfaces. Our results are important for the thermal management of high-power-density electronics implemented with diamond and other wide-band-gap semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Silver Nanoparticles Functionalized Nanosilica Grown over Graphene Oxide for Enhancing Antibacterial Effect

The continuous growth of multidrug-resistant bacteria due to the overuse of antibiotics and antibacterial agents poses a threat to human health. Silver nanoparticles, silica-based materials, and graphene-based materials have become potential antibacterial candidates. In this study, we developed an effective method of enhancing the antibacterial property of graphene oxide (GO) by growing nanosilica (NS) of approximately 50 nm on the graphene oxide (GO) surface. The structures and compositions of the materials were characterized through powdered X-ray diffraction (P-XRD), transmission electron microscopy (TEM), scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDS), ultraviolet–visible spectroscopy (UV–VIS), dynamic light scattering (DLS), Raman spectroscopy (RM), Fourier-transform infrared spectroscopy (FTIR), Brunauer–Emmet–Teller (BET) surface area, and pore size determination. The silver nanoparticles (AgNPs) with an average diameter of 26 nm were functionalized on the nanosilica (NS) surface. The composite contained approximately 3% of silver nanoparticles. The silver nanoparticles on nanosilica supported over graphene oxide (GO/NS/AgNPs) exhibited a 7-log reduction of Escherichia coli and a 5.2-log reduction of Bacillus subtilis within one hour of exposure. Both GO/NS and GO/NS/AgNPs exhibited substantial antimicrobial effects against E. coli and B. subtilis.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Observation of Electrically Tunable van Hove Singularities in Twisted Bilayer Graphene from NanoARPES

The possibility of triggering correlated phenomena by placing a singularity of the density of states near the Fermi energy remains an intriguing avenue toward engineering the properties of quantum materials. Twisted bilayer graphene is a key material in this regard because the superlattice produced by the rotated graphene layers introduces a van Hove singularity and flat bands near the Fermi energy that cause the emergence of numerous correlated phases, including superconductivity. Direct demonstration of electrostatic control of the superlattice bands over a wide energy range has, so far, been critically missing. This work examines the effect of electrical doping on the electronic band structure of twisted bilayer graphene using a back-gated device architecture for angle-resolved photoemission measurements with a nano-focused light spot. A twist angle of 12.2° is selected such that the superlattice Brillouin zone is sufficiently large to enable identification of van Hove singularities and flat band segments in momentum space. Finally, the doping dependence of these features is extracted over an energy range of 0.4 eV, expanding the combinations of twist angle and doping where they can be placed at the Fermi energy and thereby induce new correlated electronic phases in twisted bilayer graphene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Mutually Reinforced Polymer–Graphene Bilayer Membranes for Energy‐Efficient Acoustic Transduction

Abstract Graphene holds promise for thin, ultralightweight, and high‐performance nanoelectromechanical transducers. However, graphene‐only devices are limited in size due to fatigue and fracture of suspended graphene membranes. Here, a lightweight, flexible, transparent, and conductive bilayer composite of polyetherimide and single‐layer graphene is prepared and suspended on the centimeter scale with an unprecedentedly high aspect ratio of 10 5 . The coupling of the two components leads to mutual reinforcement and creates an ultrastrong membrane that supports 30 000 times its own weight. Upon electromechanical actuation, the membrane pushes a massive amount of air and generates high‐quality acoustic sound. The energy efficiency is ≈ 10–100 times better than state‐of‐the‐art electrodynamic speakers. The bilayer membrane's combined properties of electrical conductivity, mechanical strength, optical transparency, thermal stability, and chemical resistance will promote applications in electronics, mechanics, and optics.

Khan, Assad U.↗
DOE OSTI2021

Controlling hydrocarbon transport and electron beam induced deposition on single layer graphene: Toward atomic scale synthesis in the scanning transmission electron microscope

Abstract Focused electron beam induced deposition (FEBID) is a direct write technique for depositing materials on a support substrate akin to 3D printing with an electron beam (e‐beam). Opportunities exist for merging this existing technique with aberration‐corrected scanning transmission electron microscopy to achieve molecular‐ or atomic‐level spatial precision. Several demonstrations have been performed using graphene as the support substrate. A common challenge that arises during this process is e‐beam‐induced hydrocarbon deposition, suggesting greater control over the sample environment is needed. Various strategies exist for cleaning graphene in situ. One of the most effective methods is to rapidly heat to high temperatures, for example, 600℃ or higher. While this can produce large areas of what appears to be atomically clean graphene, mobile hydrocarbons can still be present on the surfaces. Here, we show that these hydrocarbons are primarily limited to surface migration and demonstrate an effective method for interrupting the flow using e‐beam deposition to form corralled hydrocarbon regions. This strategy is effective for maintaining atomically clean graphene at high temperatures where hydrocarbon mobility can lead to substantial accumulation of unwanted e‐beam deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2023

NiFe Nanoparticle Nest Supported on Graphene as Electrocatalyst for Highly Efficient Oxygen Evolution Reaction

Abstract Designing cost‐efffective electrocatalysts for the oxygen evolution reaction (OER) holds significant importance in the progression of clean energy generation and efficient energy storage technologies, such as water splitting and rechargeable metal–air batteries. In this work, an OER electrocatalyst is developed using Ni and Fe precursors in combination with different proportions of graphene oxide. The catalyst synthesis involved a rapid reduction process, facilitated by adding sodium borohydride, which successfully formed NiFe nanoparticle nests on graphene support (NiFe NNG). The incorporation of graphene support enhances the catalytic activity, electron transferability, and electrical conductivity of the NiFe‐based catalyst. The NiFe NNG catalyst exhibits outstanding performance, characterized by a low overpotential of 292.3 mV and a Tafel slope of 48 mV dec −1 , achieved at a current density of 10 mA cm − 2 . Moreover, the catalyst exhibits remarkable stability over extended durations. The OER performance of NiFe NNG is on par with that of commercial IrO 2 in alkaline media. Such superb OER catalytic performance can be attributed to the synergistic effect between the NiFe nanoparticle nests and graphene, which arises from their large surface area and outstanding intrinsic catalytic activity. The excellent electrochemical properties of NiFe NNG hold great promise for further applications in energy storage and conversion devices.

Chemistry↗
DOE OSTI2022

From classical to quantum dynamics of atomic and ionic species interacting with graphene and its analogue

Graphene and its analogues offer a broad range of application opportunities for (opto)-electronics, sensing, catalysis, phase separation, energy conversion and storage, etc. Engineering graphene properties often relies on its controllable functionalization, defect formation and patterning, and reactive gas etching. In this chapter, we survey the dynamics of graphene using classical and quantum-classical dynamics methods. We discuss the reactivity, scattering, and transmission of atomic and ionic species including Ar cluster ion, H/D, and H+/D+ on graphene flakes of various sizes, focusing on the atomic-scale motion and energy dissipation pathways involved in forming and breaking covalent bonding. Discussions on the nuclear quantum effects of light species, the effects of isotopic substitution, and the methodologies for such modeling are also included.

Garashchuk, Sofiya V.↗
DOE OSTI2020

Hard, transparent, sp3-containing 2D phase formed from few-layer graphene under compression

Despite several theoretically proposed two-dimensional (2D) diamond structures, experimental efforts to obtain such structures are in initial stage. Recent high-pressure experiments provided significant advancements in the field, however, expected properties of a 2D-like diamond such as sp 3 content, transparency and hardness, have not been observed together in a compressed graphene system. Here, we compress few-layer graphene samples on SiO 2 /Si substrate in water and provide experimental evidence for the formation of a quenchable hard, transparent, sp 3 -containing 2D phase. Our Raman spectroscopy data indicates phase transition and a surprisingly similar critical pressure for two-, five-layer graphene and graphite in the 4e6 GPa range, as evidenced by changes in several Raman features, combined with a lack of evidence of significant pressure gradients or local non-hydrostatic stress components of the pressure medium up to ≈ 8 GPa. The new phase is transparent and hard, as evidenced from indentation marks on the SiO 2 substrate, a material considerably harder than graphene systems. Furthermore, we report the lowest critical pressure (≈ 4 GPa) in graphite, which we attribute to the role of water in facilitating the phase transition. Overall, theoretical calculations and experimental data indicate a novel, surface to- bulk phase transition mechanism that gives hint of diamondene formation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

The role of temperature on defect diffusion and nanoscale patterning in graphene

Graphene is of great scientific interest due to a variety of unique properties such as ballistic transport, spin selectivity, the quantum hall effect, and other quantum properties. Nanopatterning and atomic scale modifications of graphene are expected to enable further control over its intrinsic properties, providing ways to tune the electronic properties through geometric and strain effects, introduce edge states and other local or extended topological defects, and sculpt circuit paths. The focused beam of a scanning transmission electron microscope (STEM) can be used to remove atoms, enabling milling, doping, and deposition. Utilization of a STEM as an atomic scale fabrication platform is increasing; however, a detailed understanding of beam-induced processes and the subsequent cascade of aftereffects is lacking. Here, we examine the electron beam effects on atomically clean graphene at a variety of temperatures ranging from 400 to 1000 °C. We find that temperature plays a significant role in the milling rate and moderates competing processes of carbon adatom coalescence, graphene healing, and the diffusion (and recombination) of defects. The results of this work can be applied to a wider range of 2D materials and introduce better understanding of defect evolution in graphite and other bulk layered materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of graphene surface functionalities towards controlled reinforcement of a lignin based renewable thermoplastic rubber

In this report, we describe methods to enhance mechanical properties of a renewable thermoplastic rubber by incorporating functional graphene platelets into an equal-mass mixture of lignin, a feedstock from plant biomass, and a nitrile-butadiene rubber having 41 mol % acrylonitrile content (NBR41) that form a nanocomposite. Not all lignins yield mechanically strong material when they are combined with NBR41, and thus, limit its use for such rubbery products. Here, we evaluate different graphene oxides (GO) and reduced graphene oxides (rGO) dry-powders with different surface areas, functionality, and wettability in the synthesis of performance-enhanced nanocomposites of soft lignin/NBR41 matrix via a solvent-free, high shear reactive process. High surface area GO (HSGO) platelets with strong hydrophilicity exhibit good dispersion in the multiphase lignin/NBR41 composites with lignin dispersion varying from 200 to 2000 nm, resulting in superior reinforcement over other graphene derivatives. The addition of 1–4 wt % HSGO increased the tensile stress of the lignin/NBR41 thermoplastic rubber matrix by 60–160% (15–24 MPa) and the modulus by 200–700% (60–140 MPa). Scanning electron microscopy and small angle X-ray scattering results show that the well-dispersed HSGO platelets effectively disrupt the lignin-rich aggregates in NBR41 matrix, resulting in both strength and stiffness enhancements in the formed nanocomposites. This report on performance enhancement of lignin-based renewable polymers via the production of nanocomposite would increase potential for ‘finding the value of lignin’—a grand challenge associated with modern biorefineries.

36 MATERIALS SCIENCE↗