Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Freestream Velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Direct force wall shear measurements in pressure-driven three-dimensional turbulent boundary layers

Unique, simultaneous direct measurements of the magnitude and direction of the local wall shear stress in a pressure-driven three-dimensional turbulent boundary layer are presented. The flow is also described with an oil streak wall flow pattern, a map of the wall shear stress-wall pressure gradient orientations, a comparison of the wall shear stress directions relative to the directions of the nearest wall velocity as measured with a typical, small boundary layer directionally sensitive claw probe, as well as limiting wall streamline directions from the oil streak patterns, and a comparison of the freestream streamlines and the wall flow streamlines. A review of corrections for direct force sensing shear meters for two-dimensional flows is presented with a brief discussion of their applicability to three-dimensional devices.

Mcallister, J. E.↗
NASA NTRS1985

A new approach to flow problems past a screen

A new method to simulate flows past a two-dimensional porous plate is proposed. The method is a simple application of a discrete vortex method which has been well established for flows past an inclined flat plate. In this method, a flow past a porous plate is described as superposition of the velocity potential of a uniform flow on that of a flow past a flat plate. The effect of porosity is replaced by that of a mass flow rate of the approaching freestream passing through the plate. Calculated flow features are compared with experiments. It is shown that the present method is effective in the simulation of the flow past a porous plate.

Inoue, O.↗
NASA NTRS2012

Boundary-Layer Instability Measurements in a Mach-6 Quiet Tunnel

Several experiments have been performed in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. A 7 degree half angle cone at 6 degree angle of attack with temperature-sensitive paint (TSP) and PCB pressure transducers was tested under quiet flow. The stationary crossflow vortices appear to break down to turbulence near the lee ray for sufficiently high Reynolds numbers. Attempts to use roughness elements to control the spacing of hot streaks on a flared cone in quiet flow did not succeed. Roughness was observed to damp the second-mode waves in areas influenced by the roughness, and wide roughness spacing allowed hot streaks to form between the roughness elements. A forward-facing cavity was used for proof-of-concept studies for a laser perturber. The lowest density at which the freestream laser perturbations could be detected was 1.07 x 10(exp -2) kilograms per cubic meter. Experiments were conducted to determine the transition characteristics of a streamwise corner flow at hypersonic velocities. Quiet flow resulted in a delayed onset of hot streak spreading. Under low Reynolds number flow hot streak spreading did not occur along the model. A new shock tube has been built at Purdue. The shock tube is designed to create weak shocks suitable for calibrating sensors, particularly PCB-132 sensors. PCB-132 measurements in another shock tube show the shock response and a linear calibration over a moderate pressure range.

Berridge, Dennis C.↗
NASA NTRS1980

Unsteady density and velocity measurements in the 6 foot x 6 foot wind tunnel

The methods used and the results obtained in four aero-optic tests are summarized. It is concluded that the rather large values of density fluctuation appear to be the result of much higher Mach number than freestream and the violent turbulence in the flow as it separates from the turret. A representative comparison of fairing on-fairing off rms density fluctuation indicates essentially no effect at M = 0.62 and a small effect at M = 0.95. These data indicate that some slight improvement in optical quality can be expected with the addition of a fairing, although at M = 0.62 its effect would be nil. Fairings are very useful in controlling pressure loads on turrets, but will not have first order effects on optical quality. Scale sizes increase dramatically with increasing azimuth angle for a reprensentative condition. Since both scale sizes and fluctuation levels increase (total turbulence path length also increases) with azimuth angle, substantial optical degradation might be expected. For shorter wave lengths, large degradations occur.

Rose, W. C.↗
NASA NTRS1980

Complete viscous flowfield solutions about a blunt parabolic body in a supersonic stream

A hybrid computational technique which splits the flowfield into inviscid and viscous regions is used to investigate the complete flowfield about axisymmetric parabolic blunt bodies in a supersonic stream. The solutions are carried out on the CDC CYBER-203 computer which, with its extensive memory, allows for the use of a large number of finite-difference mesh points, allowing resolution of important flowfield features. A range of freestream Mach number of 2-5 and a range of Re number based on nose radius of 500-125,000 was run for a sonic corner body. Contour plots of density, pressure, and Mach number, velocity vector plots, and surface distributions of pressure, heat transfer, and shear stress are presented. Also, correlations of the downstream extent of the base recirculation region with Re number based on nose radius are given.

Weilmuenster, K. J.↗
NASA NTRS1982

A Shuttle Upper Atmosphere Mass Spectrometer /SUMS/ experiment

A magnetic mass spectrometer is currently being adapted to the Space Shuttle Orbiter to provide repeated high altitude atmosphere data to support in situ rarefied flow aerodynamics research, i.e., in the high velocity, low density flight regime. The experiment, called Shuttle Upper Atmosphere Mass Spectrometer (SUMS), is the first attempt to design mass spectrometer equipment for flight vehicle aerodynamic data extraction. The SUMS experiment will provide total freestream atmospheric quantitites, principally total mass density, above altitudes at which conventional pressure measurements are valid. Experiment concepts, the expected flight profile, tradeoffs in the design of the total system and flight data reduction plans are discussed. Development plans are based upon a SUMS first flight after the Orbiter initial development flights.

Blanchard, R. C.↗
NASA NTRS1972

Turbulent boundary layer in an adverse pressure gradient without effect of wall curvature

The hypersonic compressible turbulent boundary layer in an adverse pressure gradient along a cylindrical axisymmetric body was studied. The tests were conducted in a Mach 6 contoured axisymmetric nozzle. An external compression cowl was used to produce the gradual adverse pressure gradient and a maximum pressure rise of 7 times the freestream static pressure was achieved in a test region of 23 cm. Boundary layer profiles of static pressure, total pressure, and total temperature, as well as wall transient heat transfer rates were measured. Comparisons of the velocity total temperature profiles to linear and quadratic relations were made. Measured heat transfer data were in good agreement with the prediction from the flat-plate reference enthalpy method. Integral parameters were also in good agreement with results of numerical solutions for compressible turbulent boundary layer equations.

Zakkay, V.↗
NASA NTRS1976

Similarity solution of the boundary-layer equations for laser heated flows

The laminar boundary-layer equations with local similarity approximation are solved in order to estimate the heat transfer rate to the wall in a laser-heated rocket thruster using pure hydrogen, where the average temperature of the hot plasma core is about 14,000 K and the core Reynolds number based on nozzle throat diameter is about 2000. Under these conditions, the density-viscosity product at the wall can be 10 times the freestream value, and the hydrogen is completely dissociated. Hence the boundary layer equations with variable transport properties are solved by a quasi-linearization technique, and the equilibrium properties of hydrogen are used in the calculations. Velocity profiles are obtained, and the wall shear and wall stagnation enthalpy gradient are plotted against the pressure gradient parameter.

Wu, P. K.↗
NASA NTRS1983

An assessment of flow-field simulation and measurement

The effectiveness of the instrumentation, techniques, and wind tunnel flow characterizations in the U.S. large scale wind tunnels for accuracy in making increasingly finer drag measurements on airfoils is assessed. The more reliable measurement is necessary due to refined designs of airfoils and the need to continue to improve the economic performance of commercial aircraft. Consequently, the effects of flows in wind tunnels, compared with those in the freestream environment, have become a critical factor. Dynamic flow properties in individual wind tunnels have to be documented in order to assure reproducible results. Laser velocimetry is a suitable tool for nonintrusive measurement of the mean velocity, turbulence intensity, and the shear stress in wind tunnel flowfields. It is suggested that future wind tunnel studies be designed to remain within the diagnostic capabilities available at the site.

Owen, F. K.↗
NASA NTRS1984

Velocities of windblown particles in saltation: Venus, Earth, and Mars

Particle velocities were determined in environmental wind tunnels capable of simulating aeolian processes on Earth, Mars, and Venus. Comparisons of results for Earth, Mars, and Venus reveal some remarkable differences. Most particles achieve speeds nearly equal to freestream wind speed on Venus, but seldom achieve half the wind speed on Mars; Earth cases are of intermediate values. This is attributed to the differences in atmospheric density and to the threshold wind speeds among the three planetary environments. Particles are more easily moved in the dense venusian atmosphere than on Mars; consequently, threshold speeds are very low, and for the range of wind speeds in which most movement is presumed to occur (just above threshold speeds), the grains need not be moving very fast to achieve 100% of the wind speed. Conversely, particles on Mars must accelerate very rapidly to achieve the speed of the high winds required for threshold, and despite the fact that saltation path lengths are long on Mars, most grains fall to the surface before achieving even 50 to 60% of freestream wind speed.

Greeley, R.↗
NASA NTRS2013

Trip-Induced Transition Measurements in a Hypersonic Boundary Layer Using Molecular Tagging Velocimetry

Measurements of mean streamwise velocity, fluctuating streamwise velocity, and instantaneous streamwise velocity profiles in a hypersonic boundary layer were obtained over a 10-degree half-angle wedge model. A laser-induced fluorescence-based molecular tagging velocimetry technique was used to make the measurements. The nominal edge Mach number was 4.2. Velocity profiles were measured both in an untripped boundary layer and in the wake of a 4-mm diameter cylindrical tripping element centered 75.4 mm downstream of the sharp leading edge. Three different trip heights were investigated: k = 0.53 mm, k = 1.0 mm and k = 2.0 mm. The laminar boundary layer thickness at the position of the measurements was approximately 1 mm, though the exact thickness was dependent on Reynolds number and wall temperature. All of the measurements were made starting from a streamwise location approximately 18 mm downstream of the tripping element. This measurement region continued approximately 30 mm in the streamwise direction. Additionally, measurements were made at several spanwise locations. An analysis of flow features show how the magnitude, spatial location, and spatial growth of streamwise velocity instabilities are affected by parameters such as the ratio of trip height to boundary layer thickness and roughness Reynolds number. The fluctuating component of streamwise velocity measured along the centerline of the model increased from approximately 75 m/s with no trip to +/-225 m/s with a 0.53-mm trip, and to +/-240 m/s with a 1-mm trip, while holding the freestream Reynolds number constant. These measurements were performed in the 31-inch Mach 10 Air Tunnel at the NASA Langley Research Center.

Bathel, Brett F.↗
NASA NTRS1988

Correlations of velocity and temperature fluctuations in the stagnation-point flow of circular cylinder in turbulent flow

Boundary layer flow and turbulence transport analyses to study the influence of the free-stream turbulence on the surface heat transfer rate and the skin friction around the stagnation point of a circular cylinder in a turbulent flow are presented. The analyses are formulated with the turbulent boundary layer equations, the Reynolds stress transport equations and the k - epsilon two-equation turbulence modeling. The analyses are used to calculate the time-averaged turbulence double correlations, the mean flow properties, the surface heat transfer rate and the skin friction with an isotropic turbulence in the freestream. The analytical results are described and compared with the existing experimental measurements. Depending on the free-stream turbulence properties, the turbulence kinetic energy can increase or decrease as the flow moves toward the surface. However, the turbulence kinetic energy induces large Reynolds normal stresses at the boundary layer edge. The Reynolds normal stresses change the boundary layer profiles of the time-averaged double correlations of the velocity and temperature fluctuations, the surface heat transfer rate and the skin friction. The free-stream turbulence dissipation rate can affect the stagnation-point heat transfer rate but the influence of the free-stream temperature fluctuation on the heat transfer rate is insignificant.

Wang, Chi R.↗
NASA NTRS1994

Computational/experimental investigation of staged injection into a Mach 2 flow

The stage normal injection of two jets of air into a Mach 2 freestream behind a rearward-facing step has been investigated using laser-induced iodine fluorescence and laser doppler anemometry techniques. A detailed data set has been compiled that includes profiles of pressure, temperature, two components of velocity, and mole fraction of the injectant at 44 locations, plus planar surveys of pressure, temperature, velocity, and mole fraction. A companion numerical study was performed using the SPARK Navier-Stokes code. Good overall agreement was observed for this complex, highly three-dimensional flowfield. Discrepancies were observed in the computed and measured total temperatures, turbulent mixing, and shock strengths. The effect of grid resolution was investigated by calculating solutions on grids of 60,000 points, 200,000 points, and 450,000 points. Differences in the solutions on the two finer grids were small. The effect of turbulence modeling was investigated by calculating solutions with three different algebraic models for the jet turbulence. Overall, the turbulence models were found to have the greatest effect on the numerical solutions, followed by the grid resolution and the injectant Mach number.

Eklund, D. R.↗
NASA NTRS2021

Hypersonic Boundary-Layer Transition on Blunted Cones at Angle of Attack

Experimental studies of cones at several high-speed facilities have demonstrated that, for small nosetip bluntness, transition onset over a circular cone moves upstream along the leeward side and downstream along the windward side, but this trend may be reversed at large bluntness values, where transition onset moves downstream along the leeward side and upstream along the windward side. A theoretical and numerical investigation is performed to characterize the effects of nose bluntness on disturbance amplification over the circular cone for several angles of attack, with the goal of understanding the potential physical mechanisms behind the experimental observations. The three-dimensional laminar basic states over a 1.5 m long, 7-degree half-angle cone with 9.525 mm nosetip radius are computed for selected angles of attack values and freestream conditions that are selected to match the Mach 10 experiments conducted within the Hypervelocity Wind Tunnel 9 at the Arnold Engineering Development Complex (AEDC). The solutions at a freestream unit Reynolds number of 17.1 million per meter are used to perform detailed instability analyses for angles of attack equal to 0, 1, 3, and 5 degrees. Results indicate that the linear amplification of stationary crossflow waves along inflection lines may begin to influence transition along the acreage of the cone for angles of attack equal to or larger than 5 degrees. The measured trend in transition front with respect to increasing angle of attack is found to be consistent with the predicted increase in the amplification factors for Mack mode disturbances along the streamline trajectories. The increase in Mack mode amplification along the windward ray for higher angles of attack is shown to be the result of a progressively earlier entropy-layer swallowing. Computations also indicate that the transition amplification factor along the windward ray is not constant and increases with the angle of attack and that the transition #-factors along the leeward ray are rather small. The nonmodal analysis for zero degrees angle of attack shows that entropy-layer disturbances with appreciably strong energy growth can coexist with Mack mode instabilities at the measured transition location.

Boundary Layer Transition↗
NASA NTRS1989

Laser velocimeter measurements of the flowfield generated by an advanced counterrotating propeller

Results are presented of an investigation to measure the flowfield generated by an advanced counterrotating pusher propeller model similar to the full-scale Unducted Fan demonstrator engine. A laser Doppler velocimeter was used to measure the velocity field in several planes normal to the centerline of the model at axial stations upstream and downstream of each rotor. During this investigation, blades of the F4/A4 type were installed on the model which was operating in a freestream Mach 0.72 regime, with the advance ratio of each rotor set at 2.80. The measured data indicate only a slight influence of the potential field of each front rotor blade on the flowfield upstream of the rotor. The data measured downstream of the front rotor characterize the tip vortices, vortex sheets and potential field nonuniformities generated by the front rotor. The unsteadiness of the flow in the rotating frame of reference of the aft rotor is also illustrated.

Podboy, Gary G.↗
NASA NTRS1982

Near-wall similarity in three-dimensional turbulent boundary layers. I - Model review. II - Pressure-driven flow results

Eleven proposed models for near-wall similarity for three-dimensional turbulent boundary layer flows are reviewed. Six of these models are comparatively simple scalar models and five are more complex and/or two-component vector models. Ten of the models can be tested as to their validity or predictive capability with the aid of measured mean velocity field, wall pressure field, and direct wall shear stress field (magnitude and direction) data. One of the models cannot be tested owing to its dependence on two parameters that are at present extremely difficult (if not impossible) to measure. Ten three-dimensional near-wall similarity models are then evaluated with direct wall shear, velocity field, and pressure gradient data from a three-dimensional pressure-driven boundary layer flow. In a primary focus of the interval where y+ is between 50 and 300, graphical results suggest that six simpler models and the freestream component of one complex model are adequate for profiles with monotone increasing skew up to about 15 deg.

Pierce, F. J.↗
NASA NTRS2009

RANS Analyses of Turbofan Nozzles with Internal Wedge Deflectors for Noise Reduction

Computational fluid dynamics (CFD) was used to evaluate the flow field and thrust performance of a promising concept for reducing the noise at take-off of dual-stream turbofan nozzles. The concept, offset stream technology, reduces the jet noise observed on the ground by diverting (offsetting) a portion of the fan flow below the core flow, thickening and lengthening this layer between the high-velocity core flow and the ground observers. In this study a wedge placed in the internal fan stream is used as the diverter. Wind, a Reynolds averaged Navier-Stokes (RANS) code, was used to analyze the flow field of the exhaust plume and to calculate nozzle performance. Results showed that the wedge diverts all of the fan flow to the lower side of the nozzle, and the turbulent kinetic energy on the observer side of the nozzle is reduced. This reduction in turbulent kinetic energy should correspond to a reduction in noise. However, because all of the fan flow is diverted, the upper portion of the core flow is exposed to the freestream, and the turbulent kinetic energy on the upper side of the nozzle is increased, creating an unintended noise source. The blockage due to the wedge reduces the fan mass flow proportional to its blockage, and the overall thrust is consequently reduced. The CFD predictions are in very good agreement with experimental flow field data, demonstrating that RANS CFD can accurately predict the velocity and turbulent kinetic energy fields. While this initial design of a large scale wedge nozzle did not meet noise reduction or thrust goals, this study identified areas for improvement and demonstrated that RANS CFD can be used to improve the concept.

DeBonis, James R.↗
NASA NTRS1986

Space-time correlation measurements in a compressible turbulent boundary layer

Single and dual hot-wire probes have been used to accomplish a first look at the large-eddy structure of a supersonic turbulent boundary layer. The investigation was performed in an axisymmetric turbulent boundary layer in the Ames High Reynolds Number wind tunnel. Freestream Mach number was 2.97, the boundary layer was approximately 1.2 cm thick, and Reynolds number = 15,000. Quantities measured were streamwise turbulence intensity and higher order statistics of mass-flow fluctuations, and space-time correlations of instantaneous streamwise velocity at two locations. Conditional sampling of the hot-wire signals was performed to detect the passage and describe the character of the large turbulent eddies. Results indicate that the large scale structure in compressible turbulence is similar to that at low subsonic flow speeds except at the boundary layer edge, where the intermittency region is narrowed in compressible flow.

Robinson, S. K.↗