SEARCH · Engineering Papers

Results for “FUELS - COMBUSTION TEMPERATURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Development of Accelerated Steady-state Test Capsule Experiments to Replicate EBR-II Fuel Behavior Using BISON Fuel Performance Analysis

Here in this work, BISON fuel performance calculations were performed to predict the fuel behavior of accelerated burnup U-Pu-Zr fuel, with temperature operation conditions of the fuel and the cladding mirroring conditions within EBR-II fuel pins. The temperature operating conditions within the FAST accelerated burnup rods were aimed at replicating EBR-II X447/X447A fuel surface and inner cladding surface temperatures. Due to the FAST capsule design, these temperatures can be replicated with fission rate densities being significantly increased. fuel performance modeling has not been assessed for novel experiments such as accelerated burnup utilizing the FAST capsule within ATR. This is an important step in understanding accelerated irradiation methods as many performance models are empirical models conforming to the results of PIE but do not always include physical models that would represent the changes in irradiation tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1940

Effect of Fuel-Air Ratio, Inlet Temperature, and Exhaust Pressure on Detonation

An accurate determination of the end-gas condition was attempted by applying a refined method of analysis to experimental results. The results are compared with those obtained in Technical Report no. 655. The experimental technique employed afforded excellent control over the engine variables and unusual cyclic reproducibility. This, in conjunction with the new analysis, made possible the determination of the state of the end-gas at any instant to a fair degree of precision. Results showed that for any given maximum pressure the maximum permissible end-gas temperature increased as the fuel-air ratio was increased. The tendency to detonate was slightly reduced by an increase in residual gas content resulting from an increase in exhaust backpressure with inlet pressure constant.

Taylor, E S↗

DOE OSTI2024

AGR-5/6/7 CAPSULE 1 THERMAL MODEL WITH OFFSET GAS GAPS

Fuel compact temperatures are a crucial factor in assessing the irradiation performance of tristructural isotropic (TRISO) fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a 3 D finite-element thermal model that was subject to simulation uncertainty. The most dominant factor in the uncertainty of calculated fuel temperatures is the gas gap uncertainty caused by the graphite holder nub-to-capsule clearance. This thermal model was revised to examine the most probable graphite offset position for Capsule 1 for four different days during the irradiation. In the analysis, the offset distance and azimuthal direction at both the top and bottom of the holder were varied. The best-fit offset was estimated based on the minimum root mean square error (RMSE) of the residuals (measured minus calculated thermocouple [TC] temperatures) for the operational TCs in Capsule 1. Near the end of the irradiation, when the graphite had shrunk and the gas gaps had grown, a peak temperature was found with maximum offset along the TC lines, with nickel introducing a potential mechanism for fuel particle failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1987

High temperature solid oxide regenerative fuel cell for solar photovoltaic energy storage

A hydrogen-oxygen regenerative fuel cell (RFC) energy storage system based on high temperature solid oxide fuel cell (SOFC) technology is described. The reactants are stored as gases in lightweight insulated pressure vessels. The product water is stored as a liquid in saturated equilibrium with the fuel gas. The system functions as a secondary battery and is applicable to darkside energy storage for solar photovoltaics.

Bents, David J.↗

DOE OSTI2022

Phosphonated polymers, and methods of production thereof, for use as polymer electrolyte membranes (PEMs) and/or catalyst ionomeric binders for electrodes in PEM fuel cells

The present disclosure provides phosphonated polymers that can be used, for example, as polymer electrolyte membranes (PEMs) and/or catalyst ionomeric binders for electrodes in PEM fuel cells, and more particularly for high-temperature PEM fuel cells. High-temperature PEM fuel cells that use phosphonated polymers of the present disclosure suffer from reduced or no acid leaching because, in at least some examples, phosphonic acid moieties are covalently bound to the backbone of the polymers. A phosphonated polymer include a backbone having one or more aromatic monomers, with each aromatic monomer having one or more phosphonic acid groups. A phosphonic acid group may include phosphonic acid or a functional group that is hydrolysable into phosphonic acid.

Park, Eun Joo↗

DOE OSTI2021

Improved MPACT energy deposition and explicit heat generation coupling with CTF

The CASL neutronics code MPACT assumes local energy deposition with equilibrium delayed energy for steady-state and transient calculations. These approximations limit the accurate representation of the heat generation in space and its variations over time, both of which are essential for power distribution and thermal–hydraulic coupling analyses. This paper presents an explicit energy deposition model considering the neutron and gamma heating of all regions and the time-dependent delayed energy. The MPACT/CTF interfaces are updated to transfer the explicit heat sources. The new model agrees well with MCNP for problems without thermal–hydraulic feedback. The MPACT/CTF coupled calculation for a hot-full-power quarter-core case using the new model exhibits a reduction of peak pin power by 2.3% and fuel centerline temperature by 17 K. The new model also shows a keff difference up to -100 pcm in depletion and a 30 K peak fuel temperature reduction in a reactivity-initiated-accident problem.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS2011

Low Cost Nuclear Thermal Rocket Cermet Fuel Element Environment Testing

Deep space missions with large payloads require high specific impulse (Isp) and relatively high thrust in order to achieve mission goals in reasonable time frames. Conventional, storable propellants produce average Isp. Nuclear thermal rockets (NTR) capable of high Isp thrust have been proposed. NTR employs heat produced by fission reaction to heat and therefore accelerate hydrogen which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high temperature hydrogen exposure on fuel elements is limited. The primary concern is the mechanical failure of fuel elements which employ high-melting-point metals, ceramics or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. It is not necessary to include fissile material in test samples intended to explore high temperature hydrogen exposure of the structural support matrices. A small-scale test bed designed to heat fuel element samples via non-contact RF heating and expose samples to hydrogen is being developed to assist in optimal material and manufacturing process selection without employing fissile material. This paper details the test bed design and results of testing conducted to date.

Bradley, David E.↗

NASA NTRS2012

Compact Fuel Element Environment Test

Deep space missions with large payloads require high specific impulse (I(sub sp)) and relatively high thrust to achieve mission goals in reasonable time frames. Conventional, storable propellants produce average I(sub sp). Nuclear thermal rockets (NTRs) capable of high I(sub sp) thrust have been proposed. NTR employs heat produced by fission reaction to heat and therefore accelerate hydrogen, which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3,000 K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high-temperature hydrogen exposure on fuel elements are limited. The primary concern is the mechanical failure of fuel elements that employ high melting point metals, ceramics, or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. It is not necessary to include fissile material in test samples intended to explore high-temperature hydrogen exposure of the structural support matrices. A small-scale test bed designed to heat fuel element samples via noncontact radio frequency heating and expose samples to hydrogen for typical mission durations has been developed to assist in optimal material and manufacturing process selection without employing fissile material. This Technical Memorandum details the test bed design and results of testing conducted to date.

Bradley, D. E.↗

DOE OSTI2024

Feasibility and performance of the staged Z-pinch: A one-dimensional study with FLASH and MACH2

Z-pinch platforms constitute a promising pathway to fusion energy research. Here, we present a one-dimensional numerical study of the staged Z-pinch (SZP) concept using the FLASH and MACH2 codes. We discuss the verification of the codes using two analytical benchmarks that include Z-pinch-relevant physics, building confidence on the codes' ability to model such experiments. Then, FLASH is used to simulate two different SZP configurations: a xenon gas-puff liner (SZP1*) and a silver solid liner (SZP2). The SZP2 results are compared against previously published MACH2 results, and a new code-to-code comparison on SZP1* is presented. Using an ideal equation of state and analytical transport coefficients, FLASH yields a fuel convergence ratio (CR) of approximately 39 and a mass-averaged fuel ion temperature slightly below 1 keV for the SZP2 scheme, significantly lower than the full-physics MACH2 prediction. For the new SZP1* configuration, full-physics FLASH simulations furnish large and inherently unstable CRs (>300) but achieve fuel ion temperatures of many kilo-electron volts. While MACH2 also predicts high temperatures, the fuel stagnates at a smaller CR. The integrated code-to-code comparison reveals how magnetic insulation, heat conduction, and radiation transport affect platform performance and the feasibility of the SZP concept.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Dispersing Agents Impact Performance of Protonated Phosphonic Acid High-Temperature Polymer Electrolyte Membrane Fuel Cells

The microstructure of ionomers plays a significant role in the performance of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs). Here, we establish direct correlations between the properties of dispersing agents and the microstructure of a protonated phosphonic acid ionomer. Most importantly, the formation of the porous structure of a protonated phosphonic acid ionomer depends on the pK a of the liquid media. Namely, the acid–base interaction between the charged polymer and dispersing agents determines the porosity in the ionomer thin films. The HT-PEMFC performance increases with the level of porosity of the ionomer, as the pores enable fast reactant gas accessibility. Overall, this study concludes the importance of the pK a of ionomers’ dispersing media for the HT-PEMFC performance.

25 ENERGY STORAGE↗

DOE OSTI2020

Prediction of Performance Variation Caused by Manufacturing Tolerances and Defects in Gas Diffusion Electrodes of Phosphoric Acid (PA)–Doped Polybenzimidazole (PBI)-Based High-Temperature Proton Exchange Membrane Fuel Cells

The automated process of coating catalyst layers on gas diffusion electrodes (GDEs) for high-temperature proton exchange membrane fuel cells results inherently into a number of defects. These defects consist of agglomerates in which the platinum sites cannot be accessed by phosphoric acid and which are the consequence of an inconsistent coating, uncoated regions, scratches, knots, blemishes, folds, or attached fine particles—all ranging from μm to mm size. These electrochemically inactive spots cause a reduction of the effective catalyst area per unit volume (cm2/cm3) and determine a drop in fuel cell performance. A computational fluid dynamics (CFD) model is presented that predicts performance variation caused by manufacturing tolerances and defects of the GDE and which enables the creation of a six-sigma product specification for Advent phosphoric acid (PA)-doped polybenzimidazole (PBI)-based membrane electrode assemblies (MEAs). The model was used to predict the total volume of defects that would cause a 10% drop in performance. It was found that a 10% performance drop at the nominal operating regime would be caused by uniformly distributed defects totaling 39% of the catalyst layer volume (~0.5 defects/μm2). The study provides an upper bound for the estimation of the impact of the defect location on performance drop. It was found that the impact on the local current density is higher when the defect is located closer to the interface with the membrane. The local current density decays less than 2% in the presence of an isolated defect, regardless of its location along the active area of the catalyst layer.

Gurau, Vladimir (ORCID:0000000327429061)↗

DOE OSTI2020

Experimental system for studying temperature gradient-driven fracture of oxide nuclear fuel out of reactor

Temperature gradients in ceramic light water reactor (LWR) uranium dioxide (UO 2 ) nuclear fuel pellets generate thermal stresses that cause fractures in the fuel beginning early in the life of fresh fuel. The combination of heating due to fission and forced convective cooling on the exterior of LWR fuel rods generates a temperature profile that is difficult to replicate outside the reactor environment. In the present study, a state-of-the-art experimental set-up using electrical heating to replicate fission heating was built and surrogate fuel materials such as ceria (CeO 2 ) were used to validate the system. Cracking experiments were conducted on these surrogates by inducing reactivity-initiated-accident (RIA) like temperature gradients in the pellets via induction and direct resistance heating. Induction heating was done using copper coils and molybdenum susceptors which heated the surrogates to a threshold temperature that is sufficiently high for the fuel material to conduct current. Thereafter, direct resistance heating was used by a D.C. power supply to introduce volumetric heating to replicate LWR operating conditions analogous to fission heating. The pellets were held against nickel electrodes and mounted on a boron nitride test-stand. All the tests were carried out in a stainless-steel vacuum chamber. Simultaneous real-time dual imaging of the surrogate pellet surface has been implemented using an optical and infrared camera system which will be mounted along axial and perpendicular directions to the pellet surface respectively. A beam-splitter was used to split the incoming radiation from the sample into two halves. While one of the beams is transmitted from the splitter through a bandpass filter to obtain optical images, the other beam is reflected from the splitter to the thermal camera to capture full field temperature gradients of the as fabricated pellet surface during crack initiation and propagation. In the current series of tests, a 2-color pyrometer was used for recording and comparing the surface and centerline temperatures of the surrogate pellets in lieu of the thermal camera. A LabVIEW data acquisition system has been set up for collecting useful data during experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Temperature-Time Modeling of Spent Fuel Cladding in Dry Storage Casks

This report uses thermal and decay heat modeling to investigate spent fuel performance and the potential for cladding to anneal in dry storage conditions. Annealing is an important feature to investigate in SNF cladding because it has a direct relationship to cladding response in storage, transportation and disposal conditions. Annealed cladding may have lower strength than unannealed cladding, however its increased ductility would provide better protection against rupture in high strain rate situations such as severe accidents. These consequences are the driver for this work however are outside of the scope of this report. The modeling focused on three representative storage systems, the TN-32B, MAGNASTOR with TSC-37 canister, and NUHOMS AHSM with a 32PTH2 canister. This covers the vertical dual-purpose, vertical ventilated and horizontal ventilated casks respectively. Decay heat modeling using high and low enrichment assemblies was used to bound the decay heat curves that might be expected in dry storage. To bound the temperature relationship, the storage casks were modeled starting at the design basis heat loads with heat decaying through time. Although the results are bounding there is not an attempt to maximize conservatism, rather the intent to form a reasonable upper limit on temperature that will be broadly applicable to the U.S. cask fleet. This will allow materials testing to focus on relevant conditions for annealing that may affect the U.S. spent fuel inventory. The results show a clear dependence on heat load pattern in time in Figure S-1 and Figure S-2. This dependence is due to the different assembly decay heat curves for different assemblies in preferentially loaded casks. It shows the need for careful decay heat modeling when examining in service fuel temperatures that are less than the cask design basis heat load. The body of the report shows percent cladding cutoffs of 300°C and 350 °C as well. These results can be used to inform testing and conclusions about cladding performance through time and the potential for cladding annealing during dry storage.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

High Temperature Polymer Electrolyte Membrane Fuel Cells with High Phosphoric Acid Retention

Phosphoric acid loss poses immense hurdles for the durability of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs). Here we report quaternary ammonium-biphosphate ion-pair HT-PEMFCs that do not lose phosphoric acids under normal and accelerated stress conditions. Additionally, our energetics study explains the acid loss behavior of the conventional phosphoric acid-polybenzimidazole (PA-PBI) system by two mechanisms. If PA loss occurs via acid evaporation, the acid loss is constant over time. On the other hand, when water activity in the PA-PBI system is high, exponential decay of PA loss occurs via the water replacement mechanism. Combined 31 P NMR and computational studies show that the proposed ion-pair system has six times higher interaction energy, which allows for containing all PAs in the membrane electrode assemblies under a broad range of operating conditions. In addition, polar interactions between the phosphonic acid ionomer and phosphoric acid explain acid retention in the electrodes of the ion-pair HT-PEMFCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2011

Low Cost Nuclear Thermal Rocket Cermet Fuel Element Environment Testing

Deep space missions with large payloads require high specific impulse and relatively high thrust to achieve mission goals in reasonable time frames.1,2 Conventional storable propellants produce average specific impulse. Nuclear thermal rockets capable of producing high specific impulse are proposed. Nuclear thermal rockets employ heat produced by fission reaction to heat and therefore accelerate hydrogen, which is then forced through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000 K), and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high-temperature hydrogen exposure on fuel elements are limited.3 The primary concern is the mechanical failure of fuel elements that employ high-melting-point metals, ceramics, or a combination (cermet) as a structural matrix into which the nuclear fuel is distributed. The purpose of the testing is to obtain data to assess the properties of the non-nuclear support materials, as-fabricated, and determine their ability to survive and maintain thermal performance in a prototypical NTR reactor environment of exposure to hydrogen at very high temperatures. The fission process of the planned fissile material and the resulting heating performance is well known and does not therefore require that active fissile material be integrated in this testing. A small-scale test bed designed to heat fuel element samples via non-contact radio frequency heating and expose samples to hydrogen is being developed to assist in optimal material and manufacturing process selection without employing fissile material. This paper details the test bed design and results of testing conducted to date.

Bradley, D. E.↗

NASA NTRS1983

CARS temperature measurements in the fuel preburner of the Space Shuttle main engine: A feasibility study

This report discusses the feasibility of making temperature profile measurements in the fuel preburner of the main engine of the space shuttle (SSME) using coherent anti-Stokes Raman spectroscopy (CARS). The principal thrust of the work is to identify problems associated with making CARS measurements in high temperature gas phase hydrogen at very high pressures (approx 400 atmospheres). To this end a theoretical study was made of the characteristics of the CAR spectra of H2 as a function of temperature and pressure and the accuracy with which temperatures can be extracted from this spectra. In addition the experimental problems associated with carrying out these measurements on a SSME at NSTL were identified. A conceptual design of a CARS system suitable for this work is included. Many of the results of the calculations made in this report are plotted as a function of temperature. In the course of presenting these results, it was necessary to decide whether the number of density or the pressure should be treated as a fixed parameter.

Beiting, E. J.↗

NASA NTRS2013

Induction Heating Model of Cermet Fuel Element Environmental Test (CFEET)

Deep space missions with large payloads require high specific impulse and relatively high thrust to achieve mission goals in reasonable time frames. Nuclear Thermal Rockets (NTR) are capable of producing a high specific impulse by employing heat produced by a fission reactor to heat and therefore accelerate hydrogen through a rocket nozzle providing thrust. Fuel element temperatures are very high (up to 3000 K) and hydrogen is highly reactive with most materials at high temperatures. Data covering the effects of high‐temperature hydrogen exposure on fuel elements are limited. The primary concern is the mechanical failure of fuel elements due to large thermal gradients; therefore, high‐melting‐point ceramics‐metallic matrix composites (cermets) are one of the fuels under consideration as part of the Nuclear Cryogenic Propulsion Stage (NCPS) Advance Exploration System (AES) technology project at the Marshall Space Flight Center. The purpose of testing and analytical modeling is to determine their ability to survive and maintain thermal performance in a prototypical NTR reactor environment of exposure to hydrogen at very high temperatures and obtain data to assess the properties of the non‐nuclear support materials. The fission process and the resulting heating performance are well known and do not require that active fissile material to be integrated in this testing. A small‐scale test bed; Compact Fuel Element Environmental Tester (CFEET), designed to heat fuel element samples via induction heating and expose samples to hydrogen is being developed at MSFC to assist in optimal material and manufacturing process selection without utilizing fissile material. This paper details the analytical approach to help design and optimize the test bed using COMSOL Multiphysics for predicting thermal gradients induced by electromagnetic heating (Induction heating) and Thermal Desktop for radiation calculations.

Gomez, C. F.↗

NASA NTRS2013

Induction Heating Model of Cermet Fuel Element Environmental Test (CFEET)

Gomez, Carlos F.↗