Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUORIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Investigation of impurity driven corrosion behavior in molten 2LiF-BeF 2 salt

A 1000 -h corrosion experiment of 316H stainless steel at 700 °C investigated the role of metal fluoride impurities CrF 2 and FeF 2 in LiF-BeF 2 (66-34 mole %) (FLiBe) salt. Inductively coupled plasma-optical emission spectroscopy (ICP-OES) demonstrated the ability to measure changes in the concentration of these fluorides in FLiBe salt. Cyclic voltammetry (CV) showed the potential for real-time quantitative concentration measurement of corrosion products in the molten salt. Materials characterization revealed that both impurity species influence the dissolution of Cr from the alloy. The collective results from these analysis methods advance the understanding of the influence impurities have on materials corrosion.

2LiF-BeF2↗
DOE OSTI2022

Effect of oxide impurities on the corrosion behavior of structural materials in molten LiF-NaF-KF

The corrosion of materials in molten fluoride salts is largely influenced by the presence of impurities in the salt. Very few studies have been done on the effect of oxide impurities on the corrosion of structural alloys in molten fluoride salts. In this study, corrosion behavior of selected alloys was studied in molten FLiNaK with the addition of different oxides such as Li 2 O, NiO, and Cr 2 O 3 . The results show that addition of oxides can lead to significant effects on this corrosion, depending on the type and amount of oxide added and the alloy being used.

14 SOLAR ENERGY↗
DOE OSTI2020

Combined electrocoagulation-microfiltration-membrane distillation for treatment of hydraulic fracturing produced water

Hydraulic fracturing flowback and produced water is a highly impaired wastewater containing dissolved salts polar and non-polar organic compounds, oil and surfactants. Here a combined electrocoagulation - microfiltration – membrane distillation process has been used to treat this wastewater. Electrocoagulation followed by microfiltration was used to pretreat the wastewater prior membrane distillation. The initial total dissolved solids (TDS) concentration was extremely high being 245,300 mg L -1 . After electrocoagulation, the total organic carbon (TOC) was reduced from 120 mg L -1 to 64 mg L -1 . Tangential flow microfiltration using a 0.1 μm pore size polyethersulfone membrane was used to separate the particulate matter after electrocoagulation and to further reduce the TOC to 44 mg L -1 . Membrane distillation was used to desalinate the pretreated produced water resulting in a high quality treated water (TDS of 56 mg L -1 and TOC 1 mg L -1 ). Three membranes with very different surface morphology were used: commercially available polyvinylidene fluoride, electrospun poly(vinylidene fluoride-co-hexafluoropropylene) nanofibers and multiwalled carbon nanotube coated polytetrafluoroethylene. The TDS in the retentate increased to over 350,000 mg L -1 . During membrane distillation, the temperature of the feed tank was maintained at 36 °C while the feed entered the module at 60 °C in order to minimize scaling on the membrane. The surface properties of an ideal membrane that is resistant to wetting and provides high flux is likely to depend on the TDS and properties of the wastewater.

42 ENGINEERING↗
DOE OSTI2024

Hydrothermal solution calorimetry in acidic aqueous solutions and revisiting the standard partial molal thermodynamic properties of Nd 3+ from 25 to 300 °C

The mobility of rare earth elements (REE) can be predicted in aqueous fluids using geochemical modeling but the accuracy of these models strongly depends on the availability of robust thermodynamic properties for the REE aqueous species. The REE 3+ aqua ions are important in the derivation of the formation constants of all the major REE complexes including the chloride, sulfate, and fluoride species which predominate in many hydrothermal-magmatic systems. However, the thermodynamic properties of the REE 3+ aqua ions are still commonly derived from the Helgeson-Kirkham-Flowers (HKF) equation of state parameters tabulated several decades ago. The standard state thermodynamic properties at reference conditions (25 °C and 1bar) and their extrapolations to high temperature need to be verified, if not revised, based on hydrothermal experiments. In this study, the enthalpy of solution was measured for synthetic Nd hydroxide from 25 to 150 ºC to retrieve the standard partial molal thermodynamic properties of Nd 3+ as a function of temperature. The experiments were conducted in aqueous perchloric acid based solutions with starting pH of 2 and varying ionic strength (0.01 to 0.09 mol/kg NaClO 4 ). The standard partial molal enthalpy of formation (Δ f H°) of Nd 3+ derived from the experimental study displays differences of up to 10 kJ/mol compared to the enthalpy values derived from the HKF equation of state in the studied temperature range. These inaccuracies are resolved by adjusting the standard partial molal Gibbs energy of formation (Δ f G°) of Nd 3+ at 25 °C and 1 bar from -672.0 to -679.7 kJ/mol. The heat capacity function (C p °) derived between 25 and 150 ºC can be described by: C p ° = a 0 + a 1 ·T + a 2 ·T -2 , with a 0 = 1256, a 1 = -2.68, a 2 = -55.56·10 6 and T in Kelvin. A set of recommended thermodynamic properties is provided for the Nd 3+ aqua ions and corrections are provided for the chloride and fluoride species to remain internally consistent with the experimentally derived properties. These results allow predicting accurately the solubility of monazite between 25 and 300 ºC. Before these corrections, the properties for the Nd 3+ aqua ions derived from the HKF parameters resulted in up to ~1.5 orders of magnitude lower monazite solubility than determined experimentally. Here, a revision of the REE +3 aqua ions properties is necessary to accurately predict the mobility of REE in hydrothermal acidic solutions.

58 GEOSCIENCES↗
DOE OSTI2022

Decomposition of PVDF to delaminate cathode materials from end-of-life lithium-ion battery cathodes

The growing demand of electric vehicles and rapid consumption of rechargeable lithium-ion batteries (LIBs) require recycling of spent cathode active materials (CAMs) to reduce hazardous wastes and supply raw materials to LIB production. To separate CAMs from the cathode, direct calcination of polyvinylidene fluoride (PVDF) binder is widely applied, which leads to high energy consumption and release of toxic hydrogen fluoride. It is desirable to have an environmentally friendly and effective alternative to traditional direct calcination. In this study, five lithium salts, LiOAc (lithium acetate), LiNO 3 , LiCl, Li 2 CO 3 , and Li 2 SO 4 , were deployed and compared for their performance in recycling CAMs. A peel-off efficiency of up to 98.5% was achieved at a LiOAc to LiNO 3 molar ratio of 3:2, salt to cathode mass ratio of 10:1, and temperature of 300 °C at a holding time of 30 min. This system avoids corrosive chemicals and minimizes particle agglomeration of recycled products. Compared with sodium salt systems (NaOAc-NaNO 3 ) or direct calcination, the LiOAc-LiNO 3 system prevented high reaction temperature or further lithium loss and minimized crystal structure and morphological changes. In conclusion, a decomposition mechanism of PVDF through adsorption of HF and fluorine substitution was proposed.

25 ENERGY STORAGE↗
DOE OSTI2022

Thermophysical properties of FLiBe using moment tensor potentials

Fluoride salts are prospective materials for applications in some next-generation nuclear reactors and their thermophysical properties at various conditions are of interest. Experimental measurement of the properties of these salts is often difficult and, in some cases, unfeasible due to challenges from high temperatures, impurity control, and corrosivity. Therefore, accurate theoretical methods are needed for fluoride salt property prediction. In this work, we used moment tensor potentials (MTP) to approximate the potential energy surface of eutectic FLiBe (66.6% LiF – 33.3% BeF2) predicted by the ab initio (DFT-D3) method. Here, we then used the developed potential and molecular dynamics to obtain several thermophysical properties of FLiBe, including radial distribution functions, density, self-diffusion coefficients, thermal expansion, specific heat capacity, bulk modulus, viscosity, and thermal conductivity. Our results show that the MTP potential approximates the potential energy surface accurately and the overall approach yields very good agreement with experimental values. The converged fitting can be obtained with less than 600 configurations generated from DFT calculations, which data can be generated in just 1200 core hours on today's typical processors. The MTP potential is faster than many machine learning potentials and about one order of magnitude slower than widely used empirical molten salt potentials such as Tosi/Fumi.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Modeling athermal phonons in novel materials using the G4CMP simulation toolkit

Understanding phonon and charge propagation in superconducting devices plays an important role in both performing low-threshold dark matter searches and limiting correlated errors in superconducting qubits. The Geant4 Condensed Matter Physics (G4CMP) package, originally developed for the Cryogenic Dark Matter Search (CDMS) experiment, models charge and phonon transport within silicon and germanium detectors and has been validated by experimental measurements of phonon caustics, mean charge-carrier drift velocities, and heat pulse propagation times. Here, in this work, we present a concise framework for expanding the capabilities for phonon transport to a number of other novel substrate materials of interest to the dark matter and quantum computing communities, including sapphire (Al 2 O 3 ), gallium arsenide (GaAs), lithium fluoride (LiF), calcium tungstate (CaWO 4 ), and calcium fluoride (CaF 2 ). We demonstrate the use of this framework in generating phonon transport properties of these materials and compare these properties with experimentally-determined values where available.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Characterizing photovoltaic backsheet adhesion degradation using the wedge and single cantilever beam tests, Part II: Accelerated tests

Photovoltaic (PV) backsheets provide critical moisture, mechanical, and electrical insulation to the backside of PV modules, but their continued functionality depends upon their ability to remain well adhered over years of harsh environmental exposure. A study of adhesive strength was conducted on several PV backsheet types exposed to indoor accelerated weathering. Two adhesion tests – the wedge test and single cantilever beam test – were used to measure adhesion energy in four backsheets: two with fluoropolymer-based outer (airside) layers – polyvinyl fluoride (PVF), polyvinylidene fluoride (PVDF) – and two with non-fluoropolymer-based outer layers–polyamide (PA) and polyethylene terephthalate (PET). The effects of changes in temperature, ultraviolet (UV) irradiance, relative humidity, and a periodic water spray were studied. The PET-, PVF- and PVDF-based backsheets all showed instances of debonding in an adhesive layer, which is commonly reported. Furthermore, for the PA-, PET-, and PVDF-based backsheets, adhesion energy dropped fairly rapidly with exposure, reaching very low levels by 4000 h. The PVF-based backsheet was relatively robust to weathering. Pull-off of an outer chalking layer in the PA- and PET-based backsheets suggested a sensitivity to UV. Adhesion in these two backsheets was also highly sensitive to changes in moisture level. Changes in UV irradiance and temperature did not show a statistically significant effect on adhesion loss for the exposure levels used. The present work is part of a two-part adhesion study on both field-weathered and indoor-exposed backsheets, and forms a basis for understanding adhesion degradation across a variety of backsheet types and degradation factors.

14 SOLAR ENERGY↗
DOE OSTI2023

Conversion efficiency improvement of ELO GaAs solar cell, deposited on water soluble sacrificial buffer

Here, we demonstrate the improvement of power conversion efficiency of an epitaxially-lifted-off single junction GaAs solar cell deposited on a water-soluble sacrificial buffer architecture by introducing an additional germanium (Ge) interlayer between GaAs and the fluoride buffer. The epitaxial lift-off (ELO) technique has been extensively used to separate III-V device layers from their single crystal GaAs substrates. However, conventional ELO requires the use of concentrated hydrofluoric acid (HF) for extended times to etch out the sacrificial layer, subsequently degrading the surface roughness of the parent wafer. As a result, the wafer has to undergo expensive and intensive chemical mechanical polishing (CMP) processes, costing about 25% of a pristine 6-inch GaAs substrate. In our previous work, we demonstrated a method to eliminating the need for CMP post-processing by using water-assisted ELO (H 2 O-ELO). A water-soluble, 3-layer buffer architecture was developed using alkaline earth compounds. However, devices suffered low performance due to a high defect density in the GaAs active layers. A Ge interlayer was introduced to provide a more favorable surface energy for GaAs growth, which leads to an improvement of GaAs crystal quality. The Ge deposition conditions were optimized to achieve a high-quality Ge layer on triple-layer fluoride buffer. Single junction GaAs devices fabricated on Ge/(Ca,Sr)F 2 /BaF 2 /(Ca,Sr)F 2 showed improvement of solar cell performance parameters featuring increases in V oc by 23.7%, and fill factor (F.F.) by 4.9%, which results in an overall improvement of power conversion efficiency from 10.3% to 12.69%.

14 SOLAR ENERGY↗
DOE OSTI2023

Development and demonstration of a rolling ball viscometer for molten salts with near-minimum liquidus NaCl–KCl

The thermophysical characterization of molten chloride and fluoride salts is a key interest for the development of advanced molten salt nuclear reactors. Viscosity is one thermophysical property of interest; a high-accuracy understanding of this property is necessary for modeling the thermal energy transfer and mass flow rate for a given molten salt system. Only a few methods have consistently been used to measure the viscosity of molten chloride and fluoride salt systems, and large discrepancies have been observed in the literature between independent studies of nearly identical salt systems. As such, exploration of novel measurement methods or implementations may allow for further validation, improved measurement accuracy, and overall improved understanding about optimal approaches for measuring molten salt viscosity. Here, in this study, a novel implementation of the rolling ball viscometry method was used to measure the viscosity of a 44/56 mol % mixture of NaCl–KCl within a temperature range of 714–838 °C, with the intent to demonstrate the feasibility of this technique for molten salt viscosity measurement cross-validation. The purity of this salt was confirmed through laser-induced breakdown spectroscopy. Measured viscosities were approximately 1.3–1.0 cP within this temperature range, and the overall uncertainty was 10.8%, which was determined through Gaussian error propagation. The results agree reasonably well with measured viscosities of similar NaCl–KCl mixtures in the literature (within 2%–20% depending on the temperature and study), although the experimental error in some of these comparative studies may be significant.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Elucidating the Redox Behavior during Atomic Layer Deposition on Lithium-Ion Battery Cathode Materials

Atomic layer deposition (ALD) has emerged as a promising technology for applying ultrathin protective coatings on lithium-ion battery (LIB) cathode surfaces to improve their cycling stability. While there have been numerous reports evaluating the electrochemical performance of these surface-modified cathode materials, the chemical changes induced on the surface of the cathode materials upon ALD coating are not fully studied. This paper describes a systematic investigation to understand the interfacial changes of 12 different cathode materials upon coating with aluminum oxide (Al 2 O 3 ) using trimethyl aluminum (TMA) and H 2 O, and aluminum fluoride (AlF 3 ) using TMA and hydrogen fluoride pyridine (HFPy). Here, the surface composition of these cathode materials, which range from simple transition metal oxides (e.g. NiO and MnO) to complex multi-element cathode materials (e.g. LiNi x Mn 1-x-y Co y O 2 , NMC), was studied via X-ray photoelectron spectroscopy (XPS). The XPS measurements reveal that the transition metals in the cathode materials undergo selective oxidation/reduction depending upon the nature of the precursor, the coating, and the cathode material. The ability to chemically modify the surface of cathode materials via vapor-phase precursor adsorption will open new avenues to systematically control the interface of the cathode materials in LIBs that are not possible by conventional coating methods.

25 ENERGY STORAGE↗
DOE OSTI2020

Lewis Acidity and Basicity: Another Measure of Carbene Reactivity

The structural and energetic reactivities of various carbenes are evaluated against a standard electrophile (proton) and a standard nucleophile (fluoride). The proton and fluoride affinities of the carbenes studied provide an increased understanding of reactivity modes and mechanisms. General classification of carbenic reactivity as a singlet nucleophilic carbene or a singlet electrophilic carbene is facilitated by this present study, and a need for further classification means along the border between electrophilic and nucleophilic reactivity is considered. The results are based on electronic structure calculations at the composite correlated molecular orbital theory G3MP2 level.

Stein, Trent H.↗
DOE OSTI2022

Reactions of Atomic Thorium and Uranium Cations with SF 6 Studied by Guided Ion Beam Tandem Mass Spectrometry

The fundamental chemistry of the thorium and uranium fluorides continues to be an area of interest because of the use of thorium and uranium fluoride compounds in nuclear fuel systems. Here, we study the reaction of thorium cations with sulfur hexafluoride for the first time and revisit the reaction of uranium cations with sulfur hexafluoride. By using guided ion beam tandem mass spectrometry, we explore the reaction pathways that become accessible well above thermal energies (E ~ 0.04 eV). Overall, we find that both Th + and U + react very efficiently with SF 6 , approaching the collision limit at both thermal and elevated energies. Here, the primary products observed at low energies include Th 1–3 + , UF 1–4 + , and SF 1–4 + , all of which are formed in barrierless, exothermic processes. SF 5 + was also observed, although the pressure dependence of this channel reveals that SF 5 + forms exothermically through secondary reactions, which the energy dependences suggest result from reactions between ThF 2 + and UF 3 + with SF 6 . At higher energies, both AnF 3 + products are observed to decay to AnF + + F 2 and both SF 4 + and SF 2 + exhibit cross sections with endothermic features. For both systems, the rise in SF 4 + can be attributed to a secondary collision between AnF + with SF 6 on the basis of the pressure dependence of the SF 4 + channel at higher energies and the rise in SF 2 + appears to result from the decomposition of SF 3 + to SF 2 + + F.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Structural Characterization of Uranium Tetrafluoride Hydrate (UF 4 ·2.5H 2 O)

Uranium tetrafluoride is an important intermediate in the nuclear fuel cycle. Facile synthesis of its hydrate, uranium tetrafluoride hydrate (UF 4 ·2.5H 2 O), has recently been reported. The hydrate forms by contacting anhydrous UF 4 with neat H 2 O at room temperature for 24 h or by exposing anhydrous UF 4 to high relative humidity (>90%) conditions for several weeks. These pathways are of clear environmental relevance. Further understanding of the structure and optical spectra of UF 4 ·2.5H 2 O, especially of the water molecules, is therefore necessary. Herein, the structure of UF 4 ·2.5H 2 O was probed using time-of-flight neutron powder diffraction to improve understanding of the crystalline water environments in the structure. The complete structure was elucidated and compared to a previously reported partial structure for UF 4 ·2.5H 2 O and a predicted complete structure from density functional theory. The crystalline structure exhibits three distinct water environments: two of the three water sites are bound to uranium, and the third water is unbound or “free”. Furthermore, the completed structure reveals an extensive hydrogen bonding network involving water–fluorine and water–water interactions. One bound water site participates in hydrogen bonding with nearby fluoride ligands (O–H···F–U), and the second bound water site participates in hydrogen bonding with the unbound water (O–H···O) and a nearby fluoride ligand (O–H···F–U); the unbound water participates in hydrogen bonding with bound water (O–H···O–U). Low-temperature experiments and thermal analysis indicate UF 4 ·2.5H 2 O is thermally stable from 10 to 358 K, undergoes dehydration at higher temperatures, and is nearly dehydrated at 473 K. Structural measurements provide foundational understanding and will inform future investigations of the thermal and environmental stability of UF 4 ·2.5H 2 O.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Impact of Disorder and Defects on Bond Energies in Highly Fluorinated Graphene

Fluorinated graphite materials are of interest for an assortment of applications and can be synthesized under a variety of synthetic conditions from many different types of carbon. Due to such variations, structural disorders in the form of defects and polymorphism are often present. Here, we investigate the impact of local structural variations on the C–F bond dissociation energies (BDEs) in carbon-based fluoride materials using density functional theory (DFT) computational methods. Employing fluorographene (FG) cluster models, we determine the impact of different C–F bonding configurations in the core of each platelet on the equilibrium BDEs for each C–F bond. The introduction of structural disorder decreases the first C–F BDE by approximately 1 eV compared to the canonical arrangement of axial C–F bonds ordered as in a network of cyclohexane “chairs”. Variability of calculated BDEs among the different polymorphs decreases upon subsequent F removal. Common structural tendencies of the adiabatic defluorination pathways for each polymorph are identified. In conclusion, our analysis suggests that at F/C ratios near 1.0, disorder in the local structure can play a significant role in the energetics of the initial carbon fluoride defluorination and that the influence of this configurational disorder diminishes with decreasing F/C ratios.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Insights into Spontaneous Solid Electrolyte Interphase Formation at Magnesium Metal Anode Surface from Ab Initio Molecular Dynamics Simulations

Spontaneous chemical reactivity at multivalent (Mg, Ca, Zn, Al) electrode surfaces is critical to solid electrolyte interphase (SEI) formation, and hence, directly affects the longevity of batteries. Here, we report an investigation of the reactivity of 0.5 M Mg(TFSI)2 in 1,2-dimethoxyethane (DME) solvent at a Mg(0001) surface using ab initio molecular dynamics (AIMD) simulations and detailed Bader charge analysis. Based on the simulations, the initial degradation reactions of the electrolyte strongly depend on the structure of the Mg(TFSI)2 species near the anode surface. At the surface, the dissociation of Mg(TFSI)2 species occurs via cleavage of the N-S bond for the solvent separated ion pair (SSIP) and via cleavage of the C-S bond for the contact ion pair (CIP) configuration. In the case of the CIP, both TFSI anions undergo spontaneous bond dissociation reactions to form atomic O, C, S, F, and N species adsorbed on the surface of the Mg anode. These products indicate that the initial SEI layer formed on the surface of the pristine Mg anode consists of a complex mixture of multiple components such as oxides, carbides, sulfides, fluorides, and nitrides. We believe that the atomic level insights gained from these simulations will lay the groundwork for the rational design of tailored and functional interphases that are critical for the success of multivalent battery technology.

Agarwal, Garvit↗
DOE OSTI2025

Surprising Relationship between Silicon Anode Calendar Aging and Electrolyte Components in a Localized High-Concentration Electrolyte System

Although localized high-concentration electrolytes (LHCEs) have been shown to improve the calendar lifetime of silicon anodes, the roles of the electrolyte constituents in calendar aging are not well understood. Here, in this work, we utilize a voltage hold protocol and an LHCE with varying molar ratios of lithium bis(fluorosulfonyl)imide (LiFSI), tetramethylene sulfone (TMS), and 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (TTE) to probe the component roles during aging. Interestingly, the estimated calendar lifetime and irreversible lithium losses from the V-hold experiments are independent of the electrolyte formulations. Contrarily, the solid electrolyte interphase (SEI) composition depends on the electrolyte formulation. X-ray photoelectron spectroscopy shows that TMS-coordinated species decompose to form insoluble alkanes and lithium hydroxide (LiOH), while lithium fluoride (LiF) originates from the anion-coordination complex. The SEI composition does not appear to play a significant role in the silicon anode passivity, as measured by parasitic current, suggesting that the SEI-electrolyte interactions dictate the calendar aging mechanisms.

Si anode↗
DOE OSTI2026

2D in-Plane Ordered MXene Nanosheets Derived from (Mo 2/3 Er 1/3 ) 2 AlC Rare-Earth i-MAX for Energy Storage Applications

MXenes have become one of the most versatile families of two-dimensional (2D) materials due to their high conductivity, hydrophilicity, and remarkable electrochemical performance. This has stimulated intense efforts to design and synthesize MXenes, including structurally unique in-plane ordered 2D MXenes called i-MXenes. Here, we have synthesized the quaternary rare earth (RE)-based i-MAX phase (Mo 2/3 Er 1/3 ) 2 AlC using an arc melting method, and the corresponding 2D i-MXene was then obtained through a LiF/HCl soft etching process. Literature studies have shown that Al and the RE element are etched out during the etching process, leading to the formation of pure vacancy-ordered Mo1.33C 2D i-MXene. However, our investigation reveals that upon exposure to a fluorine solution, the i-MAX phase forms RE fluoride impurities, which are challenging to remove through HCl−DI water washing and persist in the final product, resulting in impure Mo 1.33 C@Er i-MXene. These results were confirmed by various characterizations such as X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, and scanning transmission electron microscopy. Although the Mo 1.33 C@Er electrode showed a 24-fold increase in specific capacitance compared to its parent i-MAX phase, it still exhibited a high charge-transfer resistance arising from the insulating nature of RE fluoride byproducts, which adversely influence the overall capacitance behavior of the synthesized 2D Mo 1.33 C@Er i-MXenes. This study contributes to identifying pathways for the preparation of pure 2D i-MXenes from RE-based i-MAX phases and developing improved synthesis methods. With additional process optimization, the 2D i-MXene holds a strong potential for electrochemical energy storage applications. Additionally, the electronic structures of Mo 1.33 C were theoretically studied using first-principles density functional theory calculations, which revealed that pristine Mo 1.33 C is metallic, and this metallic nature is preserved even with −O, −F, and mixed functionalization.

chemical structure↗