Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUORIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Criticality experiments and analysis of molybdenum reflected cylindrical uranyl fluoride water solution reactors

Clean criticality data were obtained from molybdenum-reflected cylindrical uranyl-fluoride-water solution reactors. Using ENDF/B molybdenum cross sections, a nine energy group two-dimensional transport calculation of a reflected reactor configuration predicted criticality to within 7 cents of the experimental value. For these reactors, it was necessary to compute the reflector resonance integral by a detailed transport calculation at the core-reflector interface volume in the energy region of the two dominant resonances of natural molybdenum.

Fieno, D.↗
NASA NTRS1973

Plasma-sprayed metal-glass and metal-glass fluoride coatings for lubrication to 900 C

Plasma-sprayed composites, which have good oxidation-resistance and self-lubricating characteritics to 900 C, were developed. The composites are a nichrome matrix containing dispersed glass for oxidation protection and calcium fluoride for lubrication; they are applied to bearing surfaces by plasma spraying layers about 0.050 centimeters thick which are then machined to 0.025 centimeters. Oscillating bearing tests were performed in air to 900 C at unit radial loads up to 3.5 x 10 to the 7th power N/sq M (5000 psi) and a thrust load of 1960N (440 lbs). Bearings with a composite liner in the bore were in good condition after over 50,000 oscillating cycles accumulated during repeated, bearing temperatures cycles between 25 and 900 C.

Sliney, H. E.↗
NASA NTRS1972

Lubricating characteristics of polyimide bonded graphite fluoride and polyimide thin films.

A friction and wear life study was conducted on the use of a polyimide (PI) varnish as a binder for the solid lubricant, graphite fluoride (CF sub 1.1) sub n. Also studied were the lubricating properties of PI thin films with no solid lubricant additives. For comparison, similar experiments on PI-bonded MoS2 and burnished films of MoS2 or (CF sub 1.1) sub n were conducted. The best results were obtained with the PI-bonded (CF sub 1.1) sub n films. The polyimide thin films (with no solid lubricant additives) did not lubricate well at 25 C; however, when heated to 100 C, low friction and long wear lives were obtained.

Fusaro, R. L.↗
NASA NTRS1974

Plasma-sprayed metal-glass and metal-glass fluoride coatings for lubrication to 900 C

Plasma-sprayed composites, which have good oxidation resistance and self-lubricating characteristics to 900 C, were developed. The composites are a nichrome matrix containing dispersed glass for oxidation protection and calcium fluoride for lubrication; they are applied to bearing surfaces by plasma spraying layers about 0.050 cm thick which are then machined to 0.025 cm. Oscillating bearing tests were performed in air to 900 C at unit radial loads up to 5000 psi and a thrust load of 440 lb. Bearings with a composite liner in the bore were in good condition after over 50,000 oscillating cycles accumulated during repeated bearing temperature cycles between 25 and 900 C.

Sliney, H. E.↗
NASA NTRS1975

Organopolysiloxane-bonded graphite fluoride as a solid lubricant

A study was conducted on the lubricating properties of organopolysiloxane-bonded graphite fluoride (CF sub 1.1) sub n films. The effects of temperature, atmosphere, composition of organopolysiloxane, and burnishing additional (CF sub 1.1) sub n powder onto the film surface were studied. For comparison, similar experiments were conducted on organopolysiloxane-bonded MoS2 films. The results are equivalent for both films, except that in a moist air environment the wear lives of the films formulated with (CF sub 1.1) sub n are up to 10 times longer than the wear lives of the MoS2-formulated films. Comparison to other (CF sub 1.1) sub n films showed organopolysiloxane films to give better lubrication results than hand-burnished (CF sub 1.1) sub n films but not as good as polyimide-bonded (CF sub 1.1) sub n films.

Fusaro, R. L.↗
NASA NTRS1977

Analysis of diffential absorption lidar technique for measurements of anhydrous hydrogen chloride from solid rocket motors using a deuterium fluoride laser

An active optical technique (differential absorption lidar (DIAL)) for detecting, ranging, and quantifying the concentration of anhydrous HCl contained in the ground cloud emitted by solid rocket motors (SRM) is evaluated. Results are presented of an experiment in which absorption coefficients of HCl were measured for several deuterium fluoride (DF) laser transitions demonstrating for the first time that a close overlap exists between the 2-1 P(3) vibrational transition of the DF laser and the 1-0 P(6) absorption line of HCl, with an absorption coefficient of 5.64 (atm-cm) to the -1 power. These measurements show that the DF laser can be an appropriate radiation source for detecting HCl in a DIAL technique. Development of a mathematical computer model to predict the sensitivity of DIAL for detecting anhydrous HCl in the ground cloud is outlined, and results that assume a commercially available DF laser as the radiation source are presented.

Bair, C. H.↗
NASA NTRS1979

Lubricating and wear mechanisms for a hemisphere sliding on polyimide-bonded graphite fluoride film

Friction, wear life, rider wear, and film wear for a 440 C high-temperature-stainless-steel, hemispherically tipped rider sliding against polyimide-bonded graphite fluoride films were evaluated in a moist-air atmosphere at 25 C. Optical microscope and surface profilometry observations were made at various sliding intervals to determine how film thickness affected the lubricating and failure mechanisms of the films. Two lubrication regimes operated for the same load. In the first, the film supported the load and the lubricating mechanism consisted of the shear (plastic flow) of a thin layer of the lubricant between the metallic rider and the film surface. In the second, the film did not support the load (it was worn away) and the lubricating mechanism consisted of the shear of very thin lubricant films between flat areas generated on the rider and on sandblasted metallic asperities in the film wear track. Lubricant was supplied from the valleys between the asperities or from the sides of the wear track. With thicker films, wear life increased since a greater lubricant supply was available from the sides of the wear track.

Fusaro, R. L.↗
NASA NTRS1980

Lubrication and wear mechanisms of polyimide-bonded graphite fluoride films subjected to low contact stress

The tribological properties of polyimide-bonded graphite fluoride films were studied with a pin-on-disk friction apparatus. A 440 C HT stainless steel rider with a 0.95 millimeter diameter flat area was slid against the film in order to achieve a light, closely controlled contact stress. A 1 kilogram load was applied to this flat to give a projected contact stress of 14 megapascals. Two stages of lubrication were operating. In the first stage, the film supported the load and the lubricating mechanism appeared to be the shear of a thin surface layer of the film between the rider and the bulk of the film. The second stage began after the original film was worn away, and the lubricating mechanism appeared to be the shear of very thin lubricant layers between the flat area on the rider and flat plateaus generated on the sandblasted asperities of the metallic substrate. The major difference between the lubricating mechanisms of the hemispherical and flat riders was that the flat wore through the film much more slowly than did the hemisphere.

Fusaro, R. L.↗
NASA NTRS1980

Fabrication and Testing of Polyvinylidene Fluoride Capacitors

High energy density capacitors made from metallized polyvinylidene fluoride film were built and tested. Terminations of aluminum-babbitt, tin-babbitt, and all-babbitt were evaluated. All-babbit terminations appeared to be better. The 0.1 microfarad and 2 microfarad capacitors were made of 6 micrometer material. Capacitance, dissipation factor, and insulation resistance measurements were made over the ranges -55 C to 125 C and 10 Hz to 100 kHz. Twelve of forty-one 0.1 microfarad capacitors survived a 5000 hour dc plus ac life test. Under the same conditions, the 2 microfarad capacitors exhibited overheating because of excessive power loss. Some failures occurred after low temperature exposures for 48 hours. No failures were caused by vibration or temperature cycling.

Buritz, R. S.↗
NASA NTRS1981

Polyvinylidene fluoride film as a capacitor dielectric

Thin strips of polyvinylidene fluoride film (PVDF) with vacuum deposited electrodes were made into capacitors by conventional winding and fabrication techniques. These devices were used to identify and evaluate the performance characteristics offered by the PVDF in metallized film capacitors. Variations in capacitor parameters with temperature and frequence were evaluated and compared with other dielectric films. Their impact on capacitor applications is discussed.

Dematos, H. V.↗
NASA NTRS1981

Effect of load, area of contact, and contact stress on the tribological properties of polyimide bonded graphite fluoride films

A pin-on-disk type of friction and wear apparatus was used to study the effect of load, contact stress and rider area of contact on the friction and wear properties of polyimide-bonded graphite fluoride films. Different rider area contacts were obtained by initially generating flats (with areas of 0.0035, 0.0071, 0.0145, and 0.0240 cm) on 0.476-cm radius hemispherically-tipped riders. Different projected contact stresses were obtained by applying loads of 2.5-to 58.8-N to the flats. Two film wear mechanisms were observed. The first was found to be a linear function of contact stress and was independent of rider area of contact. The second was found to increase exponentially as the stress increased. The second also appeared to be a function of rider contact area. Wear equations for each mechanism were empirically derived from the experimental data. In general, friction coefficients increased with increasing rider contact area and with sliding duration. This was related to the build-up of thick rider transfer films.

Fusaro, R. L.↗
NASA NTRS1983

Piezoelectricity and pyroelectricity in polyvinylidene fluoride - Influence of the lattice structure

Piezoelectric and pyroelectric responses of beta-phase (Phase I) polyvinylidene fluoride are predicted for a model system of polarizable point dipoles. The model incorporates the influence of the orthorhombic crystal structure by including the dependence of the internal electric field on the lattice parameters. Strong anisotropy in the piezoelectric response under uniaxial stress is predicted as a consequence of the orthorhombic lattice structure. Predictions are found to be in reasonable agreement with room-temperature experimental data.

Purvis, C. K.↗
NASA NTRS1984

Effects of silver and group 2 fluorides addition to plasma sprayed chromium carbide high temperature solid lubricant for foil gas bearing to 650 deg C

A new self-lubricating coating composition of nickel aluminide-bonded chromium carbide formulated with silver and Group II fluorides was developed in a research program on high temperature solid lubricants. One of the proposed applications for this new coating composition is as a wide temperature spectrum solid lubricant for complaint foil gas bearings. Friction and wear properties were obtained using a foil gas bearing start/stop apparatus at temperatures from 25 to 650 C. The journals were Inconel 718. Some were coated with the plasma sprayed experimental coating, others with unmodified nickel aluminide/chromium carbide as a baseline for comparison. The addtitional components were provided to assist in achieving low friction over the temperature range of interest. Uncoated, preoxidized Inconel X-750 foil bearings were operated against these surfaces. The foils were subjected to repeated start/stop cycles under a 14-kPa (2-psi) bearing unit loading. Sliding contact occurred during lift-off and coastdown at surface velocities less than 6 m/s (3000 rpm). Testing continued until 9000 start/stop cycles were accumulated or until a rise in starting torque indicated the journal/bearing had failed. Comparison in coating performance as well as discussions of their properties and methods of application are given.

Wagner, R. C.↗
NASA NTRS1985

Conformational properties, torsional potential, and vibrational force field for methacryloyl fluoride - An ab initio investigation

The structure, torsional potentials, vibrational spectra, and harmonic force fields for s-cis and s-trans isomers of methacryloyl fluoride are examined to understand the conformational properties of the molecules and their relationship to macroscopic polymer properties. The structure is found to be in good agreement with experiment. It is shown by calculations that the energy difference between the cis and the transisomers is less than 1 kcal/mol at both the split valence and the split valence polarized levels, with the trans form favored. Analysis of the torsional potentials indicates that a rigid rotor model provides a reasonable description of the motion of the COF group in the molecule. The torsional barrier to interconvert the s-trans to the s-cis form is found to be 7.0 kcal/mol. A fit of the data to a three-term Fourier series shows that it is possible to reproduce the experimentally derived barrier, even though a direct determination indicates that the barrier is higher.

Laskowski, B. C.↗
NASA NTRS1986

Estimated heats of fusion of fluoride salt mixtures suitable for thermal energy storage applications

The heats of fusion of several fluoride salt mixtures with melting points greater than 973 K were estimated from a coupled analysis of the available thermodynamic data and phase diagrams. Simple binary eutectic systems with and without terminal solid solutions, binary eutectics with congruent melting intermediate phases, and ternary eutectic systems were considered. Several combinations of salts were identified, most notable the eutectics LiF-22CaF2 and NaF-60MgF2 which melt at 1039 and 1273 K respectively which posses relatively high heats of fusion/gm (greater than 0.7 kJ/g). Such systems would seemingly be ideal candidates for the light weight, high energy storage media required by the thermal energy storage unit in advanced solar dynamic power systems envisioned for the future space missions.

Misra, A. K.↗
NASA NTRS1985

Effect of chloride incorporation on the crystallization of zirconium-barium-lanthanum-aluminum fluoride glass

One aspect of the influence of preparation procedure on the crystallization behavior of a zirconium-barium-lanthanum-aluminum fluoride glass was studied. The crystallization pattern of this glass may be affected by the chlorine concentration within it. In particular, when such glasses are heated at low temperatures, the alpha-Ba-Zr-F6 crystalline phase forms only in those glasses which contain chloride.

Neilson, G. F.↗
NASA NTRS1987

Carbide-fluoride-silver self-lubricating composite

A self-lubricating, friction and wear reducing composite material is described for use over a wide temperature spectrum from cryogenic temperature to about 900 C in a chemically reactive environment comprising silver, barium fluoride/calcium fluoride eutectic, and metal bonded chromium carbide.

Sliney, Harold E.↗