SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Semiconductor package has been developed for high power semiconductor devices that operate in the GHz-frequency range at several watts. Package includes stud, insulating ring, electrically conductive washer, insulating washer, braze ring, and cap. It is mechanically strong and can be used with variety of circuits.
Provided are low-melt polyimides and poly(amic acids) (PAAs) for use in repair of electrical wire insulation, flat or ribbon wire harnesses, and flat surfaces comprised of high-performance polymers such as inflatables or solar panels applications. Also provided are methods and devices for repair of electrical insulation.
Provided are low-melt polyimides and poly(amic acids) (PAAs) for use in repair of electrical wire insulation, flat or ribbon wire harnesses, and flat surfaces comprised of high-performance polymers such as inflatables or solar panels applications. Also provided are methods and devices for repair of electrical insulation.
Graphite fluoride fibers can be produced by fluorinating pristine or intercalated graphite fibers. The higher the degree of graphitization of the fibers, the higher the temperature needed to reach the same degree of fluorination. Pitched based fibers were fluorinated to flourine-to-carbon atom rations between 0 and 1. The graphite fluoride fibers with a fluorine-to-carbon atom ration near 1 have extensive visible structural damage. On the other hand, fluorination of fibers pretreated with bromine or fluorine and bromine result in fibers with a fluorine-to-carbon atom ratio nearly equal to 0.5 with no visible structural damage. The electrical resistivity of the fibers is dependent upon the fluorine to carbon atom ratio and ranged from .01 to 10 to the 11th ohm/cm. The thermal conductivity of these fibers ranged from 5 to 73 W/m-k, which is much larger than the thermal conductivity of glass, which is the regular filler in epoxy composites. If graphite fluoride fibers are used as a filler in epoxy or PTFE, the resulting composite may be a high thermal conductivity material with an electrical resistivity in either the insulator or semiconductor range. The electrically insulating product may provide heat transfer with lower temperature gradients than many current electrical insulators. Potential applications are presented.
The relationship between the electrical behavior of GaAs Metal Insulator Semiconductor (MIS) structures and the high density discrete energy interface states (0.7 and 0.9 eV below the conduction band) was investigated utilizing photo- and thermal emission from the interface states in conjunction with capacitance measurements. It was found that all essential features of the anomalous behavior of GaAs MIS structures, such as the frequency dispersion and the C-V hysteresis, can be explained on the basis of nonequilibrium charging and discharging of the high density discrete energy interface states.
Polyphenylsulfone (PPSU) is a high-temperature, chemically resistant thermoplastic with high impact resistance that is often used in interior aircraft cabin components, medical devices, and membranes. The aforementioned properties have led to interest investigating PPSU’s compatibility with hexagonal boron nitride (hBN) platelets as a thermally conductive, electrical composite insulator for high power-density electric machines. Preliminary trials extruding PPSU-hBN composite tapes showed promising dielectric properties and higher thermal conductivity as a function of hBN concentration compared to their neat analog. On the other hand, only few studies have reported on the extrusion process and resulting thermo-mechanical properties for PPSU and its composites made with chopped fiber reinforcement or fillers, none of which containing boron nitride filler. Prospects may exist for this type of material to be incorporated into extrusion-based additive manufacturing techniques to print other composites bearing unique properties useful for aerospace. Loading levels with up to approximately 23 wt% were achieved using micro-size BN platelets without observing any significant affects to PPSU’s glass-transition temperature. This work includes a description of the rheological properties of PPSU, the extrusion parameters for mixing and compounding the PPSU-hBN composite tapes, and the thermal and thermo-mechanical properties of PPSU-hBN composites.
Polyphenylsulfone (PPSU) is a high-temperature, chemically resistant thermoplastic with high impact resistance that is often used in interior aircraft cabin components, medical devices, and membranes. The aforementioned properties have led to interest investigating PPSU’s compatibility with hexagonal boron nitride (hBN) platelets as a thermally conductive, electrical composite insulator for high power-density electric machines. Preliminary trials extruding PPSU-hBN composite tapes showed promising dielectric properties and higher thermal conductivity as a function of hBN concentration compared to their neat analog. On the other hand, only few studies have reported on the extrusion process and resulting thermo-mechanical properties for PPSU and its composites made with chopped fiber reinforcement or fillers, none of which contained boron nitride filler. Prospects may exist for this type of material to be incorporated into extrusion-based additive manufacturing techniques to print other composites bearing unique properties useful for aerospace. Loading levels with up to approximately 23 wt% were achieved using micro-size BN platelets without observing any significant affects to PPSU’s glass-transition temperature. This work includes a description of the rheological properties of PPSU, the extrusion parameters for mixing and compounding the PPSU-hBN composite tapes, and the thermal and thermo-mechanical properties of PPSU-hBN composites.
The functioning of the experimental setup and the preliminary inputs for the development of analytical models of the discharge process are presented. This allows for the development of new or modified materials and design techniques having the necessary discharge immunity to insure high reliability and long lifetime of space systems.
Solar electric propulsion for space missions, evaluating modularized ion propulsion systems to determine effect of electric isolation on system reliability, weight, etc
Experimental results of the complex magnetic permeability (µ) and the electrical conductivity (σ) of a granular paramagnetic Gadolinium Gallium Garnet (GGG: 0.3–26 vol%) and Teflon (PTFE) system are presented and discussed in relation to previously published (conductivity) and unpublished (permeability) studies on granular Fe3O4 – talc and Ni – talc wax systems. In these systems plots of the real conductivity (σ'(sub m)) against the volume fraction (φ) lie on characteristic sigmoid curves that when fitted to the Two Exponent Phenomenological Percolation Equation (TEPPE) confirm the existence of “percolation microstructures” with critical volume fractions (φ(sub c)). The plots of the real and imaginary permeability (µ'(sub m)) and (µ"(sub m)) satisfactorily fit to the TEPPE using the φ(sub c) obtained in each case from the “conductivity” measurements. In all three cases the conductivity results gave the exponent t > 2, and the permeability results gave t < 1.
The present invention uses the generation and detection of acoustic guided waves to evaluate the condition of the insulation on electrical wiring. Low order axisymmetric and flexural acoustic modes are generated in the insulated wire and travel partially in the center conductor and partially in the outer insulation. The stiffness of the insulation and the insulation's condition affect the overall wave speed and amplitude of the guided wave. Analysis of the received signal provides information about the age or useful life of the wire insulation. In accordance with the present invention, signal transmission occurs at one location on the electrical wire to be evaluated, and detection occurs at one or more locations along the electrical wire. Additional receivers can be used to improve measurement accuracy. Either the transmission transducer or one or more receiver transducers may be angled at other than 90 degrees to the wire. Generation of the guided waves can be accomplished by imparting a pressure pulse on the wire. Alternative embodiments include generation via a laser, such as a Q-switched laser or a laser diode.
The electrical behavior of zinc ions implanted into chromium-doped semiinsulating gallium arsenide was investigated by measurements of the sheet resistivity and Hall effect. Room temperature implantations were performed using fluence values from 10 to the 12th to 10 to the 15th power/sq cm at 60 keV. The samples were annealed for 30 minutes in a nitrogen atmosphere up to 800 C in steps of 200 C and the effect of this annealing on the Hall effect and sheet resistivity was studied at room temperature using the Van der Pauw technique. The temperature dependence of sheet resistivity and mobility was measured from liquid nitrogen temperature to room temperature. Finally, a measurement of the implanted profile was obtained using a layer removal technique combined with the Hall effect and sheet resistivity measurements.
Compilation of information on design procedures, electrical properties, and fabrication. Guide provides information on design procedures; magnetic and insulating material electrical properties; impregnating, encapsulating and processing techniques.
A model for the mechanism of stationary discharges over insulators in a vacuum was developed. Upon introduction of this discharge, the insulator charges as a result of secondary emissions, in such a way that electrons coming from the cathode strike with an average secondary electron yield of 1, and so that the secondary electrons return again to the insulator through the electric field near the insulator. When the secondary electrons strike, electrons with an average yield of 1 are released again. The electrons move in short faults toward the anode, which they strike with lesser energy.
High temperature insulating adhesives for vacuum applications tested, including outgassing rate, mass spectra of evolved gases, electrical and mechanical properties
External shunt capacitance effects upon electron irradiation induced voltage pulses from polyethylene terephthalate insulated ribbon wire
Explore the source record for details and available documents.
An improved method of locating small breaches in insulation on electrical wires combines aspects of the prior dielectric withstand voltage (DWV) and time-domain reflectometry (TDR) methods. The method was invented to satisfy a need for reliably and quickly locating insulation defects in spacecraft, aircraft, ships, and other complex systems that contain large amounts of wiring, much of it enclosed in structures that make it difficult to inspect. In the DWV method, one applies a predetermined potential (usually 1.5 kV DC) to the wiring and notes whether the voltage causes any arcing between the wiring and ground. The DWV method does not provide an indication of the location of the defect (unless, in an exceptional case, the arc happens to be visible). In addition, if there is no electrically conductive component at ground potential within about 0.010 in. (approximately equal to 0.254 mm) of the wire at the location of an insulation defect, then the DWV method does not provide an indication of the defect. Moreover, one does not have the option to raise the potential in an effort to increase the detectability of such a defect because doing so can harm previously undamaged insulation. In the TDR method as practiced heretofore, one applies a pulse of electricity having an amplitude of less than 25 V to a wire and measures the round-trip travel time for the reflection of the pulse from a defect. The distance along the wire from the point of application of the pulse to the defect is then calculated as the product of half the round-trip travel time and the characteristic speed of a propagation of an electromagnetic signal in the wire. While the TDR method as practiced heretofore can be used to locate a short or open circuit, it does not ordinarily enable one to locate a small breach in insulation because the pulse voltage is too low to cause arcing and thus too low to induce an impedance discontinuity large enough to generate a measurable reflection. The present improved method overcomes the weaknesses of both the prior DWV and the prior TDR method.