Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic stability behaviors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Control of elastic robotic systems by nonlinear inversion and modal damping

Energy efficient, lightweight robot arms for space applications have considerable structural flexibility. For large and fast motions, both the nonlinear coupled dynamics and the elastic behavior of the robots must be considered in control system designs. This paper presents an approach to the control of a class of flexible robotic systems. A control law is derived which decouples the joint-angle motion from the flexible motion and asymptotically decomposes the elastic dynamics into two subsystems, representing the transverse vibrations of the elastic link in two orthogonal planes. This decomposition allows the design of an elastic mode stabilizer independently based on lower order models representing structural flexibility. The closed-loop system is shown to be globally asymptotically stable and robust to uncertainty in system parameters. Simulation results are presented to show that large, fast control of joint angles can be performed in spite of space vehicle motion and uncertainty in the payload.

Singh, S. N.↗

Air Data Boom System Development for the Max Launch Abort System (MLAS) Flight Experiment

In 2007, the NASA Exploration Systems Mission Directorate (ESMD) chartered the NASA Engineering Safety Center (NESC) to demonstrate an alternate launch abort concept as risk mitigation for the Orion project's baseline "tower" design. On July 8, 2009, a full scale and passively, aerodynamically stabilized MLAS launch abort demonstrator was successfully launched from Wallops Flight Facility following nearly two years of development work on the launch abort concept: from a napkin sketch to a flight demonstration of the full-scale flight test vehicle. The MLAS flight test vehicle was instrumented with a suite of aerodynamic sensors. The purpose was to obtain sufficient data to demonstrate that the vehicle demonstrated the behavior predicted by Computational Fluid Dynamics (CFD) analysis and wind tunnel testing. This paper describes development of the Air Data Boom (ADB) component of the aerodynamic sensor suite.

Woods-Vedeler, Jessica A.↗

Modeling of Multicomponent Trace Contaminant Adsorption on Activated Carbon

Modeling of multicomponent trace contaminant adsorption on activated carbon for spacecraft life support applications presents challenges due to the very low contaminant concentrations in cabin air coupled with very strong adsorption of heavier components such as cyclic polydimethylsiloxanes. Both gas-phase and solid-phase micropore mass transfer resistances can be important, and competitive interactions between adsorbed components can result in behavior such as roll-up where lighter components displaced by heavier components have a higher concentration at the outlet than at the inlet. This paper describes the further development of a dynamic trace contaminant adsorption model based on Ideal Adsorbed Solution Theory (IAST). Alternative 1-dimensional and 2-dimensional versions of the model are described with different mass transfer resistance and driving force assumptions. Optimization of solution methods for speed and stability is also described. Mass balance equations are scaled to provide sensitivity over the wide range of component concentrations in cabin air. Model parameters are estimated from isotherm and breakthrough test data on single adsorbate and binary adsorbate systems. Multicomponent results are compared against predictions of a heritage model used extensively by NASA for trace contaminant control system (TCCS) carbon bed sizing. Finally, efforts to implement the model in a second software platform for wider access are described.

Kevin E Lange↗

Forced Displacement Technique for Measuring Blunt Body Aerodynamics in a Magnetic Suspension Wind Tunnel

The Old Dominion University/NASA Langley 6-Inch Magnetic Suspension Wind Tunnel has developed the ability to levitate blunt bodies which can oscillate freely about the yaw axis. This allows for the measurement of static and dynamic stability coefficients without sting interference. The magneic suspension controller introduces other translational forces which affect the vehicle dynamics complicating data reduction. Exciting model oscillations in a reliable way has also been a challenge. A new test method has been developed that produces capsule oscillations from forced oscillatory translational motion at the resonant yaw oscillatory frequency of the capsule. After oscillations are excited, the translational forcing motion is suspended to record free oscillation behavior as well. A data reduction method whereby a linear model of the translational and oscillatory motion is used to fit to the measured data and solve for aerodynamic coefficients has also been developed. The work presented shows that the new data reduction

blunt body↗

Forced Displacement Technique for Measuring Blunt Body Aerodynamics in a Magnetic Suspension Wind Tunnel

The Old Dominion University/NASA Langley 6-Inch Magnetic Suspension Wind Tunnel has developed the ability to levitate blunt bodies which can oscillate freely about the yaw axis. This allows for the measurement of static and dynamic stability coefficients without sting interference. The magneic suspension controller introduces other translational forces which affect the vehicle dynamics complicating data reduction. Exciting model oscillations in a reliable way has also been a challenge. A new test method has been developed that produces capsule oscillations from forced oscillatory translational motion at the resonant yaw oscillatory frequency of the capsule. After oscillations are excited, the translational forcing motion is suspended to record free oscillation behavior as well. A data reduction method whereby a linear model of the translational and oscillatory motion is used to fit to the measured data and solve for aerodynamic coefficients has also been developed. The work presented shows that the new data reduction

blunt body↗

A geometric approach to regulator and tracker design for an aerospace plane

The paper presents a nonlinear design approach drawing from singular perturbations, feedback linearization, and variable structure control, that leads to regulators with automatic gain scheduling which exhibit similar dynamic behavior over the entire flight envelope of the aerospace plane. Additionally, design approach provides for a systematic way to counter disturbance effects as well as modeling uncertainties. The unifying feature of the three nonlinear feedback control methodologies is that they all have a geometric interpretation. First, the translational dynamics are decomposed into reduced-order slow and fast dynamics by way of a formal singular perturbation analysis. After feedback linearization the fast dynamics are robustly stabilized via a variable structure control approach. The slow dynamics are stabilized using conventional proportional-integral compensation based on the nominal slow dynamics. A number of sample command and disturbance responses at opposite ends of the flight envelope are presented for a nonlinear aerospace plane model.

Van Buren, Mark A.↗

Time-dependent Computational Studies of Premixed Flames in Microgravity

This report describes the research performed at the Center for Reactive Flow and Dynamical Systems in the Laboratory for Computational Physics and Fluid Dynamics, at the Naval Research Laboratory, in support of NASA Microgravity Science and Applications Program. The primary focus of this research is on investigating fundamental questions concerning the propagation and extinction of premixed flames in earth gravity and in microgravity environments. Our approach is to use detailed time-dependent, multispecies, numerical models as tools to simulate flames in different gravity environments. The models include a detailed chemical kinetics mechanism consisting of elementary reactions among the eight reactive species involved in hydrogen combustion, coupled to algorithms for convection, thermal conduction, viscosity, molecular and thermal diffusion, and external forces. The external force, gravity, can be put in any direction relative to flame propagation and can have a range of values. Recently more advanced wall boundary conditions such as isothermal and no-slip have been added to the model. This enables the simulation of flames propagating in more practical systems than before. We have used the numerical simulations to investigate the effects of heat losses and buoyancy forces on the structure and stability of flames, to help resolve fundamental questions on the existence of flammability limits when there are no external losses or buoyancy forces in the system, to understand the interaction between the various processes leading to flame instabilities and extinguishment, and to study the dynamics of cell formation and splitting. Our studies have been able to bring out the differences between upward- and downward-propagating flames and predict the zero-gravity behavior of these flames. The simulations have also highlighted the dominant role of wall heat losses in the case of downward-propagating flames. The simulations have been able to qualitatively predict the formation of multiple cells and the cessation of cell-splitting. Our studies have also shown that some flames in a microgravity environment can be extinguished due to a chemical instability and without any external losses. However, further simulations are needed to more completely understand upward-propagating and zero-gravity flames as well as to understand the potential effect of radiative heat losses.

Kailasanath, K.↗

Passive three-axis stabilization of the Long Duration Exposure Facility

This paper presents an analysis of the attitude dynamics of the Long Duration Exposure Facility (LDEF). LDEF is a large cylindrical gravity gradient stabilized earth satellite which is planned to be delivered to a 270-n mi circular orbit by the space shuttle. The fundamental linear stability, capture requirements, and pitch bias constraints generated by the Garber instability are discussed. Numerical simulations, based on the full nonlinear equations for the coupled orbital and attitude motion of the vehicle and the viscous magnetic damper, show stable behavior of the spacecraft and a damping time constant of 30 to 70 orbits.

Huckins, E. K., III↗

Tank Investigation of the EDO Model 142 Hydro-Ski Research Airplane

A tank investigation has been conducted of a 1/10-size powered-dynamic model of the Edo model 142 hydra-ski research airplane. The results of tests of two configurations are presented: One included a large ski and a ski well; the other, a small ski without a well. Water take-offs would be possible with the available thrust for either configuration: however, the configuration with the large ski emerged sooner and had less resistance from ski emergence until take-off. Longitudinal stability and landing behavior in smooth water were satisfactory for both configurations. Some alteration to the design of the tail would be desirable in order to reduce the spray loads.

Ramsen, John A.↗

MOD-0 wind turbine dynamics test correlations

The behavior of the teetered, downwind, free yaw, MOD-0 wind turbine, as represented by NASA dynamic test data, was used to support confidence in the Hamilton Standard computer code simulations. Trim position, performance at trim, and teeter response as predicted by the computer codes were compared to test results. Using the computer codes, other possible configurations for MOD-0 were investigated. Several new test configurations are recommended for exploring free yaw behavior. It is shown that eliminating rotor tilt and optimizing cooling and blade twist can contribute to good free yaw behavior and stability. The effects of rotor teeter, teeter gravity balance, inflow and other physical and operating parameters were also investigated.

Brooks, B. M.↗

The 32nd CDC: System identification using interval dynamic models

Motivated by the recent explosive development of results in the area of parametric robust control, a new technique to identify a family of uncertain systems is identified. The new technique takes the frequency domain input and output data obtained from experimental test signals and produces an 'interval transfer function' that contains the complete frequency domain behavior with respect to the test signals. This interval transfer function is one of the key concepts in the parametric robust control approach and identification with such an interval model allows one to predict the worst case performance and stability margins using recent results on interval systems. The algorithm is illustrated by applying it to an 18 bay Mini-Mast truss structure.

Keel, L. H.↗

Sustained small oscillations in nonlinear control systems

Some results of bifurcation theory were used to study the existence of small-amplitude periodic behavior in launch vehicle dynamics, assuming that nonlinearity exists as a cubic term in the rudder response. The analysis follows closely Sattinger's (1973) approach to the theory of periodic bifurcations. The conditions under which a bifurcating branch of orbitally stable periodic solutions will exist are determined. It is shown that in more complicated cases, the conditions under which the system matrix has a pair of simple purely imaginary eigenvalues can be determined with the aid of linear stability techniques.

George, J. H.↗

On regulators with a prescribed degree of stability

Several important aspects of the Regulator with a Prescribed Degree of Stability (RPDS) methodology and its applications are considered. The solution of the time varying RPDS problem as well as the characterization of RPDS closed loop eigenstructure properties are obtained. Based on the asymptotic behavior of RPDS root loci, a one step algorithm for designing Regulators with Prescribed Damping Ratio (RPDR) is developed. The robustness properties of RPDS are characterized in terms of the properties of the return difference and the inverse return difference matrices for the RPDS state feedback loop. This class of regulators is found to possess excellent multiloop margins with respect to stability and degree of stability properties. The ability of RPDS design to tolerate changing operating conditions and unmodelled dynamics are illustrated with a multiterminal dc/ac power system example. The output feedback realization of RPDS requires the use of Linear Quadratic Gaussian (LQG) methodology.

Ng, P. T. P.↗

Control Of Flexible Structures-2 (COFS-2) flight control, structure and gimbal system interaction study

The second Control Of Flexible Structures Flight Experiment (COFS-2) includes a long mast as in the first flight experiment, but with the Langley 15-m hoop column antenna attached via a gimbal system to the top of the mast. The mast is to be mounted in the Space Shuttle cargo bay. The servo-driven gimbal system could be used to point the antenna relative to the mast. The dynamic interaction of the Shuttle Orbiter/COFS-2 system with the Orbiter on-orbit Flight Control System (FCS) and the gimbal pointing control system has been studied using analysis and simulation. The Orbiter pointing requirements have been assessed for their impact on allowable free drift time for COFS experiments. Three fixed antenna configurations were investigated. Also simulated was Orbiter attitude control behavior with active vernier jets during antenna slewing. The effect of experiment mast dampers was included. Control system stability and performance and loads on various portions of the COFS-2 structure were investigated. The study indicates possible undesirable interaction between the Orbiter FCS and the flexible, articulated COFS-2 mast/antenna system, even when restricted to vernier reaction jets.

Fay, Stanley↗

Ambiguous Stability of Glaciers at Bed Peaks

Increasing ice flux from glaciers retreating over deepening (retrograde) bed topography has been implicated in the recent acceleration of mass loss from the Greenland and Antarctic ice sheets. We show in observations that some glaciers have remained at peaks in bed topography without retreating despite enduring significant changes in climate. Observations also indicate that some glaciers which persist at bed peaks undergo sudden retreat years or decades after the onset of local ocean or atmospheric warming. Using model simulations, we show that persistence of a glacier at a bed peak is caused by ice slowing as it flows up a reverse-sloping bed to the peak. Persistence at bed peaks may lead to two very different future behaviors for a glacier: one where it persists at a bed peak indefinitely, and another where it retreats from the bed peak after potentially long delays following climate forcing. However, it is nearly impossible to distinguish which of these two future behaviors will occur from current observations. We conclude that inferring glacier stability from observations of persistence obscures our true commitment to future sea-level rise under climate change. We recommend that further research is needed on seemingly stable glaciers to determine their likely future.

ice dynamics↗

Boolean difference equations. I - Formulation and dynamic behavior

In many biological and physical systems, feedback mechanisms depend on a set of thresholds associated with the state variables. Each feedback has a characteristic time scale. It is suggested that delay-difference equations for Boolean-valued variables are an appropriate mathematical framework for such situations: the feedback thresholds result in the discrete, on-off character of the variables, and the interaction time scales of the feedbacks are expressed as delays. The initial-value problem for Boolean delay equations (B-Delta-Es) is formulated, and shown to have unique solutions for all times. Examples of periodic and aperiodic solutions are given. Aperiodic solutions have increasing complexity which depends on time t roughly as t to the l-1 power, l being the number of delays. Stability of solutions is defined, and some examples of stability analysis are given; additional stability questions are raised. The present formulation of (B-Delta-Es) is compared with related work and generalizations are suggested.

Dee, D.↗

Instabilities in a nonlinear model of a passive damper

During a study of the dynamic characteristics of a wire rope vibration isolation system constructed with helical isolatoars, an interesting instability was observed. In addition to experimental investigation of this system, a semi-empirical model having nonlinear stiffness, nth-power velocity damping, and variable Coulomb-type friction damping was developed. Results obtained using ACSL compare well with experimental data. The primary emphasis of this paper, however, centers on the instabilities and largea-response behavior of this semi-empirical model. Stabilizing effects are discussed.

Tinker, Michael L.↗

General Rotorcraft Aeromechanical Stability Program (GRASP): Theory manual

The general rotorcraft aeromechanical stability program (GRASP) was developed to calculate aeroelastic stability for rotorcraft in hovering flight, vertical flight, and ground contact conditions. GRASP is described in terms of its capabilities and its philosophy of modeling. The equations of motion that govern the physical system are described, as well as the analytical approximations used to derive them. The equations include the kinematical equation, the element equations, and the constraint equations. In addition, the solution procedures used by GRASP are described. GRASP is capable of treating the nonlinear static and linearized dynamic behavior of structures represented by arbitrary collections of rigid-body and beam elements. These elements may be connected in an arbitrary fashion, and are permitted to have large relative motions. The main limitation of this analysis is that periodic coefficient effects are not treated, restricting rotorcraft flight conditions to hover, axial flight, and ground contact. Instead of following the methods employed in other rotorcraft programs. GRASP is designed to be a hybrid of the finite-element method and the multibody methods used in spacecraft analysis. GRASP differs from traditional finite-element programs by allowing multiple levels of substructure in which the substructures can move and/or rotate relative to others with no small-angle approximations. This capability facilitates the modeling of rotorcraft structures, including the rotating/nonrotating interface and the details of the blade/root kinematics for various types. GRASP differs from traditional multibody programs by considering aeroelastic effects, including inflow dynamics (simple unsteady aerodynamics) and nonlinear aerodynamic coefficients.

Hodges, Dewey H.↗