Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Doubling method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

High-temperature fatigue in metals - A brief review of life prediction methods developed at the Lewis Research Center of NASA

The presentation focuses primarily on the progress we at NASA Lewis Research Center have made. The understanding of the phenomenological processes of high temperature fatigue of metals for the purpose of calculating lives of turbine engine hot section components is discussed. Improved understanding resulted in the development of accurate and physically correct life prediction methods such as Strain-Range partitioning for calculating creep fatigue interactions and the Double Linear Damage Rule for predicting potentially severe interactions between high and low cycle fatigue. Examples of other life prediction methods are also discussed. Previously announced in STAR as A83-12159

Halford, G. R.↗

Neutron radiation tolerance of Au-activated silicon

Double injection devices prepared by the introduction of deep traps, using the Au activation method have been found to tolerate gamma irradiation into the Gigarad (Si) region without significant degradation of operating characteristics. Silicon double injection devices, using deep levels creacted by Au diffusion, can tolerate fast neutron irradiation up to 10 to the 15th n/sq cm. Significant parameter degradation occurs at 10 to the 16th n/sq cm. However, since the actual doping of the basic material begins to change as a result of the transmutation of silicon into phosphorus for neutron fluences greater than 10 to the 17th/sq cm, the radiation tolerance of these devices is approaching the limit possible for any device based on initially doped silicon.

Joyner, W. T.↗

Neurogenic orthostatic hypotension: a double-blind, placebo-controlled study with midodrine

PURPOSE: To investigate the efficacy and safety of midodrine for treatment of patients with orthostatic hypotension due to autonomic failure. PATIENTS: Ninety-seven patients with orthostatic hypotension were randomized in a 4-week, double-blinded, placebo-controlled study with a 1-week placebo run-in period. Patients ranged in age from 22 to 86 years (mean: 61 years). METHODS: After a 1-week run-in phase, either placebo or midodrine at a dose of 2.5 mg, 5 mg, or 10 mg was administered three times a day for 4 weeks. Both the placebo group and the 2.5-mg midodrine group received constant doses throughout the double-blind phase. The patients receiving 5 mg or 10 mg of midodrine were given doses that were increased at weekly intervals by 2.5-mg increments until the designated dose was reached. Efficacy evaluations were based on an improvement at 1-hour postdose in standing systolic blood pressure and in symptoms of orthostatic hypotension (syncope, dizziness/lightheadedness, weakness/fatigue, and low energy level). RESULTS: Midodrine (10 mg) increased standing systolic blood pressure by 22 mm Hg (28%, p < 0.001 versus placebo). Midodrine improved (p < 0.05) the following symptoms of orthostatic hypotension compared to placebo: dizziness/lightheadedness, weakness/fatigue, syncope, low energy level, impaired ability to stand, and feelings of depression. The overall side effects were mainly mild to moderate. One or more side effects were reported by 22% of the placebo group compared with 27% of the midodrine-treated group. Scalp pruritus/tingling, which was reported by 10 of 74 (13.5%) of the midodrine-treated patients, was most frequent. Other reported side effects included supine hypertension (8%) and feelings of urinary urgency (4%). CONCLUSION: We conclude that midodrine is an effective and well-tolerated treatment for moderate-to-severe orthostatic hypotension associated with autonomic failure.

NASA Discipline Number 14-10↗

Three-dimensional elastic stress and displacement analysis of finite geometry solids containing cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement fields in finite geometry bars containing central, surface, and double-edge cracks under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Normal stresses and the stress intensity factor variation along the crack periphery are calculated using the obtained displacement field. The reported results demonstrate the usefulness of this method in calculating stress intensity factors for commonly encountered crack geometries in finite solids.

Kring, J.↗

Three-dimensional elastic stress and displacement analysis of finite geometry solids containing cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement fields in finite geometry bars containing central, surface, and double-edge cracks under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Normal stresses and the stress intensity factor variation along the crack periphery are calculated using the obtained displacement field. The reported results demonstrate the usefulness of this method in calculating stress intensity factors for commonly encountered crack geometries in finite solids.

Kring, J.↗

The Heat of Formation of HNO

The HNO molecule is of interest in both combustion and atmospheric chemistry. For example, Guadagnini et al. have recently presented ab initio potential energy surfaces for the three lowest lying electronic states of HNO and then used these in examining several chemical reactions that take place in the combustion of nitrogen containing fuels and in the oxidation of atmospheric nitrogen. We have previously studied the ground state potential energy surface (i.e., stationary points along the HNO reversible reaction HON path), vibrational spectrum (using an accurate quartic force field), zero-point energy, and bonding of HNO using coupled-cluster ab initio methods. HNO is also very interesting because of the unique nature of its bonding characteristics. That is, the potential energy surface is very flat along the H-N bonding coordinate thereby giving unusual harmonic and fundamental vibrational frequencies, and the H-N bond energy is rather weak in comparison to other H-N bond energies. In fact, using experimental heats of formation for HNO, H, and NO, the H- bond energy is computed to be only 49.9 kcal/ mol (298 K). However, ab initio calculations of isodesmic reaction energies involving HNO, FNO, ClNO, and several other molecules have shown that there is an inconsistency in the experimental heats of formation of the XNO (X double bond H, F, and Cl) species. Hence the motivation for this study was to determine a very accurate (Delta)H(sub f, sup o) value for HNO using state-of-the-art ab initio methods. Based on many recent studies it is evident that the singles and doubles coupled-cluster method that includes a perturbational estimate of the effects of connected triple excitations, denoted CCSD(T), in conjunction with large one-particle basis sets should be reliable to better than +/- 0.8 kcal/mol for this quantity. The computational methodology is described in the next section followed by our results and discussion. Conclusions are presented in the final section.

Lee, Timothy J.↗

Picosecond pulse measurements using the active laser medium

A simple method for measuring the pulse lengths of synchronously pumped dye lasers which does not require the use of an external nonlinear medium, such as a doubling crystal or two-photon fluorescence cell, to autocorrelate the pulses is discussed. The technique involves feeding the laser pulses back into the dye jet, thus correlating the output pulses with the intracavity pulses to obtain pulse length signatures in the resulting time-averaged laser power. Experimental measurements were performed using a rhodamine 6G dye laser pumped by a mode-locked frequency-doubled Nd:YAG laser. The results agree well with numerical computations, and the method proves effective in determining lengths of picosecond laser pulses.

Bernardin, James P.↗

Effect of sweep angles on aerodynamic performance of double arrow wing - An analytical study

Hybrid wing planforms are studied for adoption on supersonic transport and fighter aircraft. The free vortex sheet method is used to determine effects of the leading-edge sweep angles on the aerodynamic performance of a double arrow wing with a strake. Results show lift and drag increase with the increase of the inboard and outboard leading-edge sweep angles. However, the lift-to-drag ratio is little influenced by the changes in these sweep angles. Spanwise surface pressure distributions on the aft region are influenced by the inboard sweep angle while the outboard sweep angle has no effect on these pressures. Finally, the experimental data and predicted results are compared to show good agreement.

Reddy, C. S.↗

Double photon excitation of high-Rydberg atoms as a long-lived submillimeter detector

A method and apparatus for detecting submillimeter or IR radiation is disclosed. A rare gas, such as xenon, is supplied at its ground state via a pressurized cylinder and an adjustable leak valve into a cryogenically cooled detection area. The ground state of xenon is double photon excited to a particularized level of the Rydberg series by a resonance lamp and a laser. The doubly excited gas is then further excited by the radiation to be measured. A field ionization and an ion measurement indicative of the radiation intensity is achieved.

Chutjian, A. N.↗

Angular momentum desaturation for Skylab using gravity gradient torques

An angular momentum desaturation method for momentum exchange devices of orbiting spacecraft is described. The specific application of the method is to the Skylab which contains three double-gimbaled control moment gyros for precise attitude control and maneuvering. It is assumed that the attitude reference is inertially fixed and that two of the vehicle principal moments of inertia are much larger than the third. Gravity gradient torques and resultant angular momentum accumulation are developed for small deviations from the reference. The assumed moment-of-inertia distribution allows desaturation about all axes with only two attitude angles each for the two axes with large moments of inertia. The necessary desaturation maneuvers can be decoupled for a special set of orbital coordinates. All maneuvers are made during the night portion of the orbit, and the percentage utilized for desaturation is selectable. Expressions for the attitude angle commands are developed assuming infinite vehicle rates. The effect of finite rates introduces an efficiency into the desaturation. Expressions for this efficiency are developed and means for compensation are treated. Arbitrary misalignments between geometric vehicle axes and principal moment-of-inertia axes are permissible. An angle bias about the sun line minimizes the angular momentum accumulation about the sun line projection into the orbital plane. Adaptive desaturation maneuver limiting consistent with the available maneuver momentum is included.

Kennel, H. F.↗

Comparative studies of grain size separates of 60009

Five samples from 60009, the lower half of a double drive tube, were analyzed via grain-size methods, with particle types classified and counted in the coarser grain sizes. Studies were undertaken of particle types and distributions by petrographic methods, of magnetic fractions, of the size splits and magnetic splits as analyzed by ferromagnetic resonance (FMR) techniques, of maturity (based on agglutinate content, FMR index Is/FeO, mean size of sub-cm material, magnetic fraction), of possible reworking or mixing in situ, and of depositional history. Maturity indices are in substantial agreement for all of the five samples. Strong positive correlation of percent agglutinates and percent bedrock-derived lithic fragments, combined with negative correlation of those components with percent single crystal plagioclase, argue against in situ reworking of the same soil.

Mckay, D. S.↗

Structural analysis of hollow blades: Torsional stress analysis of hollow fan blades for aircraft jet engines

A torsional stress analysis of hollow fans blades by the finite element method is presented. The fans are considered to be double circular arc blades, hollowed 30 percent, and twisted by a component of the centrifugal force by the rated revolution. The effects of blade hollowing on strength and rigidity are discussed. The effects of reinforcing webs, placed in the hollowed section in varying numbers and locations, on torsional rigidity and the convergence of stresses, are reported. A forecast of the 30 percent hollowing against torsional loadings is discussed.

Ogawa, A.↗

A remarkable operator version of the Navier-Stokes equation

The Navier-Stokes equation is transformed into a closed nonlinear equation for the convected curl operator. It is shown how Lie algebraic methods can be employed to solve the obtained double-commutator equation. The proposed operator equation provides a way to the further development of the Navier-Stokes fluid flow theory.

Rosen, G.↗

Forming electrical interconnections through semiconductor wafers

An information processing system based on CMOS/SOS technology is being developed by NASA to process digital image data collected by satellites. An array of holes is laser drilled in a semiconductor wafer, and a conductor is formed in the holes to fabricate electrical interconnections through the wafers. Six techniques are used to form conductors in the silicon-on-sapphire (SOS) wafers, including capillary wetting, wedge extrusion, wire intersection, electroless plating, electroforming, double-sided sputtering and through-hole electroplating. The respective strengths and weaknesses of these techniques are discussed and compared, with double-sided sputtering and the through-hole plating method achieving best results. In addition, hollow conductors provided by the technique are available for solder refill, providing a natural way of forming an electrically connected stack of SOS wafers.

Anthony, T. R.↗

Factors influencing elastic stresses in double cantilever beam specimens

An elastic stress analysis was conducted for a double cantilever beam (DCB) specimen using finite-element methods. The purpose of this study was to identify the important parameters that influence stresses ahead of the delamination front. The study focused on an aluminum DCB specimen, typical of adhesively-bonded joints, and on a graphite/epoxy specimen representing a cocured composite. Opening mode sigma sub y stresses ahead of the crack tip were calculated and compared with those for a monolithic reference specimen. Beyond the singularity-dominated region very near the crack tip, the sigma sub y distribution was elevated compared to the monolithic case. Both the adhesive thickness and the adherend transverse (thickness-direction) stiffness were found to influence the elevation of sigma sub y. In contrast, adherend thickness and longitudinal stiffness has very little effect on this stress distribution. Estimates for adhesive yielding beyond the aluminum DCB crack tip showed that both the area and height of the plastic zone increased to a peak value for increasing adhesive thicknesses. Results from this study would provide insight for comparing data from different DCB specimens and for designing new DCB specimens.

Crews, J. H., Jr.↗

Factors influencing elastic stresses in double cantilever beam specimens

An elastic stress analysis was conducted for a double cantilever beam (DCB) specimen using finite-element methods. The purpose of this study was to identify the important parameters that influence stresses ahead of the delamination front. The study focused on an aluminum DCB specimen, typical of adhesively-bonded joints, and on a graphite/epoxy specimen representing a cocured composite. Opening mode sigma sub y stresses ahead of the crack tip were calculated and compared with those for a monolithic reference specimen. Beyond the singularity-dominated region very near the crack tip, the sigma sub y distribution was elevated compared to the monolithic case. Both the adhesive thickness and the adherend transverse (thickness-direction) stiffness were found to influence the elevation of sigma sub y. In contrast, adherend thickness and longitudinal stiffness has very little effect on this stress distribution. Estimates for adhesive yielding beyond the aluminum DCB crack tip showed that both the area and height of the plastic zone increased to a peak value for increasing adhesive thicknesses. Results from this study would provide insight for comparing data from different DCB specimens and for designing new DCB specimens.

Crews, J. H., Jr.↗

Pdf - Transport equations for chemically reacting flows

The closure problem for the transport equations for pdf and the characteristic functions of turbulent, chemically reacting flows is addressed. The properties of the linear and closed equations for the characteristic functional for Eulerian and Lagrangian variables are established, and the closure problem for the finite-dimensional case is discussed for pdf and characteristic functions. It is shown that the closure for the scalar dissipation term in the pdf equation developed by Dopazo (1979) and Kollmann et al. (1982) results in a single integral, in contrast to the pdf, where double integration is required. Some recent results using pdf methods obtained for turbulent flows with combustion, including effects of chemical nonequilibrium, are discussed.

Kollmann, W.↗