Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Extrapolation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Correaltion of full-scale drag predictions with flight measurements on the C-141A aircraft. Phase 2: Wind tunnel test, analysis, and prediction techniques. Volume 1: Drag predictions, wind tunnel data analysis and correlation

The degree of cruise drag correlation on the C-141A aircraft is determined between predictions based on wind tunnel test data, and flight test results. An analysis of wind tunnel tests on a 0.0275 scale model at Reynolds number up to 3.05 x 1 million/MAC is reported. Model support interference corrections are evaluated through a series of tests, and fully corrected model data are analyzed to provide details on model component interference factors. It is shown that predicted minimum profile drag for the complete configuration agrees within 0.75% of flight test data, using a wind tunnel extrapolation method based on flat plate skin friction and component shape factors. An alternative method of extrapolation, based on computed profile drag from a subsonic viscous theory, results in a prediction four percent lower than flight test data.

Macwilkinson, D. G.↗
NASA NTRS1983

A computer program for estimating the aerodynamic characteristics of NACA 16-series airfoils

A computer program written in a table ""look-up'' format, is presented which provides a comprehensive data base on NACA 16-series airfoils. The geometry covered is limited to cambers for a design-lift coefficient from 0.0 to 0.7 and thickness ratios from 4 to 21%. The data include Mach numbers from 0.3 to 1.6, angles of attack from -4 to 8 degrees, and lift coefficients from 0.0 to 0.8. Extrapolation is used to obtain data from Mach numbers, angles of attack, and lift coefficients beyond those for which data are available. A routine to adjust the lift and drag coefficients beyond stall is included. The uses and limitations of the program are also discussed.

Maksymiuk, C. M.↗
NASA NTRS1978

Prediction of orbiter RSI tile gap heating ratios from NASA/Ames double wedge model test

In-depth gap heating ratios for Orbiter RSI tile sidewalls were predicted based on near steady state temperature measurements obtained from double wedge model tests. An analysis was performed to derive gap heating ratios which would result in the best fit of test data; provide an assessment of open gap response, and supply the definition of gap filler requirements on the Orbiter. A comparison was made of these heating ratios with previously derived ratios in order to verify the extrapolation of the wing glove data to Orbiter flight conditions. The analysis was performed with the Rockwell TPS Multidimensional Heat Conduction Program for a 3-D, 2.0-inch thick flat RSI tile with 255 nodal points. The data from 14 tests was used to correlate with the analysis. The results show that the best-fit heating ratios at the station farthest upstream on the model for most gap depths were less than the extrapolated values of the wing glove model heating ratios. For the station farthest downstream on the model, the baseline heating ratios adequately predicted or over-predicted the test data.

Source record↗
NASA NTRS2017

CO2 Capacity Sorbent Analysis using Volumetric Measurement Approach

In support of air revitalization system sorbent selection for future space missions, Ames Research Center (ARC) has performed CO2 capacity tests on various sorbents to complement structural strength tests from Marshall Space Flight Center (MSFC). The materials of interest are: Grace Davison Grade 544 13x, Honeywell UOP APG III, VSA-10, BASF 13x, and Grace Davison Grade 522 5A. Each sorbents CO2 capacity was measured using a Micromeritics ASAP 2020 Physisorption Volumetric Analysis machine to produce 0C, 10C, 25C, 50C, and 75C isotherms. These datasets were then extrapolated using Langmuir 3-Site and Toth isotherm models to compare with previously measured capacity data from MSFC using a thermogravimetric analysis approach. The modeling and extrapolation from ARC data correlated well with data measured at MSFC.

Air Revitalization↗
NASA NTRS2010

A Rat Body Phantom for Radiation Analysis

To reduce the uncertainties associated with estimating the biological effects of ionizing radiation in tissue, researchers rely on laboratory experiments in which mono-energetic, single specie beams are applied to cell cultures, insects, and small animals. To estimate the radiation effects on astronauts in deep space or low Earth orbit, who are exposed to mixed field broad spectrum radiation, these experimental results are extrapolated and combined with other data to produce radiation quality factors, radiation weighting factors, and other risk related quantities for humans. One way to reduce the uncertainty associated with such extrapolations is to utilize analysis tools that are applicable to both laboratory and space environments. The use of physical and computational body phantoms to predict radiation exposure and its effects is well established and a wide range of human and non-human phantoms are in use today. In this paper, a computational rat phantom is presented, as well as a description of the process through which that phantom has been coupled to existing radiation analysis tools. Sample results are presented for two space radiation environments.

Qualls, Garry D.↗
NASA NTRS1986

Latitudinal extent of the heliospheric current sheet and modulation of galactic cosmic rays

Possible correlations were investigated between the modulation of galactic cosmic rays and changes in the maximum heliographic latitude of the heliospheric current sheet during solar maximum. Solar photospheric magnetic field data from 1976-82 were extrapolated by means of potential theory to obtain the maximum latitudinal extent of the current sheet in the northern and southern hemispheres. The latitudinal differences were compared with terrestrial neutron flux data and Pioneer 10 data on cosmic rays with energies below 200 MeV at heliocentric distances of 10-30 AU. Account was taken for the time delay for the solar wind to propagate out to the spacecraft location. The current sheet maxima were nearly symmetrical about the solar equator except during sunspot maxima, when the solar poles were reversing. Significant changes in the latitudinal symmetry were highly correlated with the neutron data and cosmic fluctuations at Pioneer 10. The sensitivity of cosmic rays to the polarity reversals is in accordance with predictions of the gradient drift model.

Smith, E. J.↗
NASA NTRS1999

Sonic Boom Prediction and Minimization of the Douglas Reference OPT5 Configuration

Conventional CFD methods and grids do not yield adequate resolution of the complex shock flow pattern generated by a real aircraft geometry. As a result, a unique grid topology and supersonic flow solver was developed at Northrop Grumman based on the characteristic behavior of supersonic wave patterns emanating from the aircraft. Using this approach, it was possible to compute flow fields with adequate resolution several body lengths below the aircraft. In this region, three-dimensional effects are diminished and conventional two-dimensional modified linear theory (MLT) can be applied to estimate ground pressure signatures or sonic booms. To accommodate real aircraft geometries and alleviate the burdensome grid generation task, an implicit marching multi-block, multi-grid finite-volume Euler code was developed as the basis for the sonic boom prediction methodology. The Thomas two-dimensional extrapolation method is built into the Euler code so that ground signatures can be obtained quickly and efficiently with minimum computational effort suitable to the aircraft design environment. The loudness levels of these signatures can then be determined using a NASA generated noise code. Since the Euler code is a three-dimensional flow field solver, the complete circumferential region below the aircraft is computed. The extrapolation of all this field data from a cylinder of constant radius leads to the definition of the entire boom corridor occurring directly below and off to the side of the aircraft's flight path yielding an estimate for the entire noise "annoyance" corridor in miles as well as its magnitude. An automated multidisciplinary sonic boom design optimization software system was developed during the latter part of HSR Phase 1. Using this system, it was found that sonic boom signatures could be reduced through optimization of a variety of geometric aircraft parameters. This system uses a gradient based nonlinear optimizer as the driver in conjunction with a computationally efficient Euler CFD solver (NIIM3DSB) for computing the three-dimensional near-field characteristics of the aircraft. The intent of the design system is to identify and optimize geometric design variables that have a beneficial impact on the ground sonic boom. The system uses a simple wave drag data format to specify the aircraft geometry. The geometry is internally enhanced and analytic methods are used to generate marching grids suitable for the multi-block Euler solver. The Thomas extrapolation method is integrated into this system, and hence, the aircraft's centerline ground sonic boom signature is also automatically computed for a specified cruise altitude and yields the parameters necessary to evaluate the design function. The entire design system has been automated since the gradient based optimization software requires many flow analyses in order to obtain the required sensitivity derivatives for each design variable in order to converge on an optimal solution. Hence, once the problem is defined which includes defining the objective function and geometric and aerodynamic constraints, the system will automatically regenerate the perturbed geometry, the necessary grids, the Euler solution, and finally the ground sonic boom signature at the request of the optimizer.

Siclari, Michael J.↗
NASA NTRS2001

Searching for the Beginning of the Ozone Turnaround Using a 22-Year Merged Satellite Data Set

We have used the data from six satellite instruments that measure the total column amount of ozone to construct a consistent merged data set extending from late 1978 into 2000. The keys to constructing a merged data set are to minimize potential drift of individual instruments and to accurately establish instrument-to-instrument offsets. We have used the short-wavelength D-pair measurements (306nm-313nm) of the SBUV and SBUV/2 instruments near the equator to establish a relatively drift-free record for these instruments. We have then used their overlap with the Nimbus 7 and EP TOMS instruments to establish the relative calibration of the various instruments. We have evaluated the drift uncertainty in our merged ozone data (MOD) set by examining both the individual instrument drift uncertainty and the uncertainty in establishing the instrument- to-instrument differences. We conclude that the instrumental drift uncertainty over the 22-year data record is 0.9 %/decade (2-sigma). We have compared our MOD record with 37 ground stations that have a continuous record over that time period. We have a mean drift with respect to the stations of +0.3 %/decade which is within 1-sigma of our uncertainty estimate. Using the satellite record as a transfer standard, we can estimate the capability of the ground instruments to establish satellite calibration. Adding the statistical variability of the station drifts with respect to the satellite to an estimate of the overall drift uncertainty of the world standard instrument, we conclude that the stations should be able to be used to establish the drift of the satellite data record to within and uncertainty of 0.6 %/decade (2-sigma). Adding to this an uncertainty due to the-incomplete global coverage of the stations, we conclude that the station data should be able to establish the global trend with an uncertainty of about 0.7 %/decade, slightly better than for the satellite record. We conclude that merging the two records together gives only a slight improvement in the uncertainty. Keeping them separate gives the greater confidence of two independent measures of the ozone trend and potential recovery. We fit the trend in our MOD record through May of 1991 and then extrapolated forward to see if the data at the end of the record was above the statistical model as a measure of ozone recovery as was done in the last WMO/UNEP assessment report. Because our data set drifts with respect to the ground-stations through May of 1991, we calculated a smaller global trend (-1.1 %/decade) than in the WMO/UNEP report. Our data in 1998 and 1999 was, on average 2 DU above the extrapolated statistical model with a 2-sigma uncertainty of 6 DU. For the combined mid-latitudes of the northern and southern hemispheres, the data was 5 DU above the extrapolated statistical model with a 2-sigma uncertainty of 10 DU. These may be signs of recovery, but they are still statistically insignificant.

Stolarski, Richard S.↗
NASA NTRS1988

Boundary layer development as a function of chamber pressure in the NASA Lewis 1030:1 area ratio rocket nozzle

Through the use of theoretical predictions of fluid properties and experimental heat transfer and thrust measurements, the zones of laminar, transitional, and turbulent boundary layer flow were defined for the NASA Lewis 1030:1 area ratio rocket nozzle. Tests were performed on the nozzle at chamber pressures from 350 to 100 psia. For these conditions, the throat diameter Reynolds numbers varied from 300,000 to 1 million. The propellants used were gaseous hydrogen and gaseous oxygen. Thrust measurements and nozzle outer wall temperature measurements were taken during the 3-sec test runs. Comparison of experimental heat transfer and thrust data with the corresponding predictions from the Two-Dimensional Kinetics (TDK) nozzle analysis program indicated laminar flow in the nozzle at a throat diameter Reynolds number of 320,000 or chamber pressure of 360 psia. Comparison of experimental and predicted heat transfer data indicated transitional flow up to and including a chamber pressure of 1000 psia. Predicted values of the axisymmetric acceleration parameter within the convergent and divergent nozzle were consistent with the above results. Based upon an extrapolation of the heat transfer data and predicted distributions of the axisymmetric acceleration parameter, transitional flow was predicted up to a throat diameter Reynolds number of 220,000 or 2600-psia chamber pressure. Above 2600-psia chamber pressure, fully developed turbulent flow was predicted.

Smith, Tamara A.↗
NASA NTRS1988

Boundary layer development as a function of chamber pressure in the NASA Lewis 1030:1 area ratio rocket nozzle

Through the use of theoretical predictions of fluid properties and experimental heat transfer and thrust measurements, the zones of laminar, transitional, and turbulent boundary layer flow were defined for the NASA Lewis 1039:1 area ratio rocket nozzle. Tests were performed on the nozzle at chamber pressures from 350 to 100 psia. For these conditions, the throat diameter Reynolds numbers varied from 300,000 to 1 million. The propellants used were gaseous hydrogen and gaseous oxygen. Thrust measurements and nozzle outer wall temperature measurements were taken during the 3-sec test runs. Comparison of experimental heat transfer and thrust data with the corresponding predictions from the Two-Dimensional Kinetics (TDK) nozzle analysis program indicated laminar flow in the nozzle at a throat diameter Reynolds number of 320,000 or chamber pressure of 360 psia. Comparison of experimental and predicted heat transfer data indicated transitional flow up to and including a chamber pressure of 1000 psia. Predicted values of the axisymmetric acceleration parameter within the convergent and divergent nozzle were consistent with the above results. Based upon an extrapolation of the heat transfer data and predicted distributions of the axisymmetric acceleration parameter, transitional flow was predicted up to a throat diameter Reynolds number of 220,000 or 2600-psia chamber pressure. Above 2600-psia chamber pressure, fully developed turbulent flow was predicted.

Smith, Tamara A.↗
NASA NTRS1988

A possible explanation for the inconsistency between the Giotto grain mass distribution and ground-based observations

Giotto measured the in situ Halley dust grain mass distribution with 2 instruments, Particle Impact Analyzer and Dust Impact Detection System (DIDSY), as well as the total intercepted mass from the deceleration of the spacecraft (Giotto Radio-Science Experiment, GRE). Ground based observations made shortly before encounter have fluxes much higher than would be predicted from Giotto data. It is concluded that Giotto DIDSY and GRE data represent observations of dust originating from a narrow track along the nucleus. They are consistent with ground based data, if assumptions are made about the level of activity along this track. The actual size distribution that should be used for modeling of the whole coma should not include the large mass excess actually observed by Giotto. Extrapolation of the small grain data should be used, since for these grains the velocity dispersion is low and temporal changes at the nucleus would not affect the shape of the mass distribution.

Perry, C. H.↗
NASA NTRS1992

Limitations on wind-tunnel pressure signature extrapolation

Analysis of some recent experimental sonic boom data has revived the hypothesis that there is a closeness limit to the near-field separation distance from which measured wind tunnel pressure signatures can be extrapolated to the ground as though generated by a supersonic-cruise aircraft. Geometric acoustic theory is used to derive an estimate of this distance and the sample data is used to provide a preliminary indication of practical separation distance values.

Mack, Robert J.↗
NASA NTRS1973

Preliminary lift and drag characteristics of the F-8 supercritical wing airplane

A flight research program is being conducted using a supercritical wing attached to a modified F-8 fuselage to demonstrate the potential benefits of the supercritical wing concept in a realistic cruise flight environment. One of the primary goals of the flight program is to determine the drag-divergence Mach number, that is, the Mach number at which the total vehicle drag increases significantly. Another objective of the program is to show how well wind-tunnel data can be used to predict the performance of a supercritical wing configuration in the transonic Mach number region from 0. 9 to 1. 0. Comparisons of this nature are important in view of the uncertainties in the present methods for extrapolating wind-tunnel-model data to flight Reynolds numbers, determining the effect of wall interference on the model results, and simulating the flow separation characteristics on the model wing to correspond to the large-scale wing. However, in comparing these wind-tunnel and flight results, it must be taken into account that this supercritical wing test configuration is of only intermediate scale und that a full-scale transport would have Reynolds numbers three to five times larger.

Jon S. Pyle↗
NASA NTRS1993

Metal-silicate thermochemistry at high temperature - Magma oceans and the 'excess siderophile element' problem of the earth's upper mantle

Low-temperature metal-silicate partition coefficients are extrapolated to magma ocean temperatures. If the low-temperature chemistry data is found to be applicable at high temperatures, an important assumption, then the results indicate that high temperature alone cannot account for the excess siderophile element problem of the upper mantle. For most elements, a rise in temperature will result in a modest increase in siderophile behavior if an iron-wuestite redox buffer is paralleled. However, long-range extrapolation of experimental data is hazardous when the data contains even modest experimental errors. For a given element, extrapolated high-temperature partition coefficients can differ by orders of magnitude, even when data from independent studies is consistent within quoted errors. In order to accurately assess siderophile element behavior in a magma ocean, it will be necessary to obtain direct experimental measurements for at least some of the siderophile elements.

Capobianco, Christopher J.↗
NASA NTRS2005

Planar Laser-Induced Iodine Fluorescence Measurements in Rarefied Hypersonic Flow

A planar laser-induced fluorescence (PLIF) technique is discussed and applied to measurement of time-averaged values of velocity and temperature in an I(sub 2)-seeded N(sub 2) hypersonic free jet facility. Using this technique, a low temperature, non-reacting, hypersonic flow over a simplified model of a reaction control system (RCS) was investigated. Data are presented of rarefied Mach 12 flow over a sharp leading edge flat plate at zero incidence, both with and without an interacting jet issuing from a nozzle built into the plate. The velocity profile in the boundary layer on the plate was resolved. The slip velocity along the plate, extrapolated from the velocity profile data, varied from nearly 100% down to 10% of the freestream value. These measurements are compared with results of a DSMC solution. The velocity variation along the centerline of a jet issuing from the plate was measured and found to match closely with the correlation of Ashkenas and Sherman. The velocity variation in the oblique shock terminating the jet was resolved sufficiently to measure the shock wave thickness.

Cecil, Eric↗
NASA NTRSDate not supplied

GeoNEX-SUBSETS: Cutouts of geostationary satellite data over long-term monitoring sites

Satellite remote sensing data are important tool for extrapolating the knowledge obtained at the Fluxnet towers. We introduce our GEO-NEX geostationary satellite subset products, which make it easy to compare between ground observation and Geo-NEX products. The MODIS subset has been frequently used for validating ecosystem models developed at flux towers and upscaling the observed flux data to regional scales. However, MODIS on the polar orbiting satellites can observe target regions only once a day, while the Fluxnet eddy-covariance data are compiled as sub-hourly datasets. As a results, summarizing the sub-hourly flux data into daily statistics is necessary for the comparison between MODIS and Flux data. Here, the new generation geostationary satellite sensors (GOES-16/17 ABI and Himawari-8/9 AHI) has the high-frequent observation feature (10 minutes) in addition to similar spectral band and spatial resolution with MODIS. The high frequent observation allows us to compare the flux diurnal cycle with geostationary satellite sensor data. Some studies have already shown the effective utilization of time series of geostationary satellite data for ecosystem modeling. We are producing NEX Level-1G products, which is the gridded Top-of-Atmosphere reflectance and brightness temperature data of geostationary satellite sensors. We cut out the NEX Level-1G data using the same file format with the MODIS subset except for the projection. The other data products (e.g., surface reflectance, land surface temperature, vegetation indices and climate data) will be also added upon their availability. We selected the ground observation sites from Fluxnet, Phenocam, and AERONET networks. The NEX subset data will be provided through NASA NEX data portal.

GeoNEX↗
NASA NTRS1993

An experimental investigation of a Mach 3.0 high-speed civil transport at supersonic speeds

An experimental study was conducted to determine the aerodynamic characteristics of a proposed high speed civil transport. This configuration was designed to cruise at Mach 3.0 and sized to carry 250 passengers for 6500 n.mi. The configuration consists of a highly blended wing body and features a blunt parabolic nose planform, a highly swept inboard wing panel, a moderately swept outboard wing panel, and a curved wingtip. Wind tunnel tests were conducted in the Langley Unitary Plan Wind Tunnel on a 0.0098-scale model. Force, moment, and pressure data were obtained for Mach numbers ranging from 1.6 to 3.6 and at angles of attack ranging from -4 to 10 deg. Extensive flow visualization studies (vapor screen and oil flow) were obtained in the experimental program. Both linear and advanced computational fluid dynamics (CFD) theoretical comparisons are shown to assess the ability to predict forces, moments, and pressures on configurations of this type. In addition, an extrapolation of the wind tunnel data, based on empirical principles, to full-scale conditions is compared with the theoretical aerodynamic predictions.

Hernandez, Gloria↗
NASA NTRS1977

Investigation of real-gas and viscous effects on the aerodynamic characteristics of a 40 deg half-cone with suggested correlations for the shuttle orbiter

Parameters were evaluated that might be used to correlate shuttle orbiter aerodynamic data to be used in extrapolating from wind-tunnel to flight conditions. Preliminary calculations indicate that the lee-side forces will have an insignificant influence on the aerodynamic characteristics of the orbiter for moderate angle-of-attack entries; therefore, this work is focused on phenomena which have an overriding influence on windward forces, namely, real-gas (equilibrium and nonequilibrium) and viscous-interaction effects. Analytically determined flow fields previously obtained on 40 deg blunted cones were used as a data source to evaluate various correlation parameters. Inviscid effects were found to be the dominant contributor to the aerodynamic coefficients in the altitude range of 64 to 76.2 km. The most suitable correlation of the aerodynamic forces on these cones is based on local dynamic pressure and local Mach number.

Hunt, J. L.↗