Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Color confinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Transient liquid-crystal technique used to produce high-resolution convective heat-transfer-coefficient maps

In this transient technique the preheated isothermal model wall simulates the classic one-dimensional, semi-infinite wall heat transfer conduction problem. By knowing the temperature of the air flowing through the model, the initial temperature of the model wall, and the surface cooling rate measured at any location with time (using the fast-response liquid-crystal patterns recorded on video tape), the heat transfer coefficient can be calculated for the color isothermal pattern produced. Although the test was run transiently, the heat transfer coefficients are for the steady-state case. The upstream thermal boundary condition was considered to be isothermal. This transient liquid-crystal heat-transfer technique was used in a transient air tunnel in which a square-inlet, 3-to-1 exit transition duct was placed. The duct was preheated prior to allowing room temperature air to be suddenly drawn through it. The resulting isothermal contours on the duct surfaces were revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record was made of the temperature and time data for all points on the duct surfaces during each test. The duct surfaces were uniformly heated using two heating systems: the first was an automatic temperature-controlled heater blanket completely surrounding the test duct like an oven, and the second was an internal hot-air loop through the inside of the test duct. The hot-air loop path was confined inside the test duct by insulated heat dams located at the inlet and exit ends of the test duct. A recirculating fan moved hot air into the duct inlet, through the duct, out of the duct exit, through the oven, and back to the duct inlet. The temperature nonuniformity of the test duct model wall was held very small. Test results are reported for two inlet Reynolds numbers of 200,000 and 1,150,000 (based on the square-inlet hydraulic diameter) and two free-stream turbulence intensities of about 1 percent, which is typical of wind tunnels, and up to 20 percent (using a grid), which is typical of real engine conditions.

Hippensteele, Steven A.↗

Synthesis and characterization of bismuth doped barium sulphide nanoparticles

We have synthesized BaS:Bi nanocrystalline powder of average grain size 35 nm by solid-state diffusion method using sodium thiosulphate as a flux. During this work we have optimized the nature and amount of flux, amount of the dopant and temperature of firing for maximum yield of photoluminescence. The samples were characterized by X-ray powder diffraction (XRD) method, transmission electron microscopy (TEM), photoluminescence (PL) and UV-visible techniques. On excitation by 425 nm, these nanophosphors give one emission peak at 575 nm which corresponds to green color. In the excitation spectra of these particles there are two peaks at 350 nm and 425 nm. The effect of dopant concentration on the photoluminescence of BaS:Bi nanocrystallites has been studied which is in agreement with the principle of concentration quenching. The energy band gap of bismuth doped BaS nanopowder has been calculated to be 4.25 eV and is blue shifted in comparison to their bulk counterparts. The blue shift may be due to the quantum confinement in the particles.

36 MATERIALS SCIENCE↗

50 Years of quantum chromodynamics

Quantum Chromodynamics, the theory of quarks and gluons, whose interactions can be described by a local SU(3) gauge symmetry with charges called “color quantum numbers”, is reviewed; the goal of this review is to provide advanced Ph.D. students a comprehensive handbook, helpful for their research. When QCD was “discovered” 50 years ago, the idea that quarks could exist, but not be observed, left most physicists unconvinced. Then, with the discovery of charmonium in 1974 and the explanation of its excited states using the Cornell potential, consisting of the sum of a Coulomb-like attraction and a long range linear confining potential, the theory was suddenly widely accepted. This paradigm shift is now referred to as the November revolution. It had been anticipated by the observation of scaling in deep inelastic scattering, and was followed by the discovery of gluons in three-jet events.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Laser Plasma Interaction in the MG Magnetic Field (Final Report)

Strong magnetic fields change properties of plasma. Employment of the magnetic fields can improve conditions for inertial confinement fusion. Compression and heating of the magnetized plasma is a base of the MagLIF pulsed power approach to the controlled fusion. Study of expansion and heating of plasma in the external magnetic fields, development of plasma instabilities, parametric and other effects are important for basic physics and applications. The main goal of the research for the grant was experimental investigation of laser produced plasma in the well characterized and controlled MG magnetic fields. We developed a platform for investigation of high intensity laser-plasma interaction (LPI) in the MG fields using a university-scale pulsed power machine. A Zebra machine at UNR generated transverse magnetic fields of 3 MG on the surface of the rod load and longitudinal fields of 1.4 MG in the coil loads. The magnetic fields were characterized with two-color Faraday rotation diagnostics. The pulsed power machine provided almost static magnetic fields for LPI compared to the much faster laser driven magnetic fields. We found that eddy currents in the rising magnetic field generate plasma on the metal targets. Eddy currents did not impact Si and CH dielectric targets. A Leopard laser with intensity in the focus up to 10 19 W/cm 2 produced plasma in the MG magnetic fields. The modified reflected Faraday diagnostics was used to study laser driven B-field at the MTW laser at Laboratory for Laser Energetics, UR. We demonstrated a slow dependence of the magnetic field in the coil on the applied laser intensity. The magnetic field increased by a factor of 2 if laser intensity increased by a factor of 30. This scaling is important for comparison of experiments at different laser facilities. Expansion of the plasma in the 2-3 MG external B-field was studied. Laser-produced plasma in the azimuthal magnetic field took the unique form of a thin disc expanding radially with a velocity of 250 km/s and confined in the vertical direction. A HYDRA MHD program at the University of Rochester was applied for simulations of LPI in the magnetic field B >3 MG. Simulations for the plasma disc parameters and the expansion dynamics were in a good agreement with experiments. Generation of narrow dense plasma jets in the longitudinal magnetic field of 0.6-0.8 MG was studied. Narrow plasma jets reached a length of 3-4 mm with the electron plasma density of (0.2-1.2)x10 20 cm -3 . A jet tip propagated with the velocity of 160-200 km/s. MHD simulations showed a good agreement of the dynamics of the formation of plasma jets with experiments. These jets are relevant to astrophysical jets. Simulations of K-shell spectra of Si plasma was performed for LPI in the B-field. The laser prepulse generated plasma near the laser target. A PrismSPECT model with a MeV electron beam produced by the laser was used. The spectral modelling showed the increased plasma density by a factor by 2-3 in the magnetic field. This was in agreement with the observed dynamics of the plasma plume confined by the axial magnetic field. The two-plasmon decay was studied in the 2.5-3 MG transversal magnetic fields. Strong 2-3.5 nm spectral widening and a 2-4 nm shifts of “red” and “blue” 3/2ω 0 spectral components were observed. The large shift and widening exceed the expected temperature and magnetic shift. PIC simulations are performing to clarify physics of this effect. The experimental research program for the grant is completed. New plasma effects in the MG fields were studied at the university-scale pulsed power generator. Two graduate and two undergraduate UNR and UR students carried experiments at the Zebra generator, supported and developed plasma diagnostics, provided data processing, and performed MHD simulations of LPI in the strong magnetic field. Research results are published in 9 referred papers and presented in 12 conferences. Program manager: Kramer U. Akli; Collaborators: R. C. Mancini and H. Sawada, University of Nevada, Reno (UNR); R. Betti and A. V. Maximov, University of Rochester (UR).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Small-scale cook-off experiments and models of ammonium nitrate

Here, we have completed a series of small-scale cook-off experiments of ammonium nitrate (AN) prills in our Sandia Instrumented Thermal Ignition test at nominal packing densities of about 0.8 g/cm 3 . We increased the boundary temperature of our aluminum confinement cylinder from room temperature to a prescribed set-point temperature in 10 min. Our set-point temperature ranged from 508 to 538 K. The external temperature of the confining cylinder was held at the set-point temperature until ignition. We used type K thermocouples to measure temperatures associated with several polymorphic phase changes as well as melting and boiling. As the AN boiled, our thermocouples were destroyed by corrosion, which may have been caused by reaction of hot nitric acid (HNO 3 ) with nickel to form nickel nitrate, Ni(NO 3 ) 2 . Videos of the corroding thermocouples showed a green solution that was similar to the color of Ni(NO 3 ) 2 . We found that ignition was imminent as the AN boiling point was exceeded. Ignition of the AN prills was modeled by solving the energy equation with an energy source due to desorption of moisture and decomposition of AN to form equilibrium products. A Boussinesq approximation was used in conjunction with the momentum equation to model flow of the liquid AN. We found that the prediction of ignition was not sensitive to small perturbations in the latent enthalpies.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

NONLINEAR COLOR-METALLICITY RELATIONS OF GLOBULAR CLUSTERS. III. ON THE DISCREPANCY IN METALLICITY BETWEEN GLOBULAR CLUSTER SYSTEMS AND THEIR PARENT ELLIPTICAL GALAXIES

One of the conundrums in extragalactic astronomy is the discrepancy in observed metallicity distribution functions (MDFs) between the two prime stellar components of early-type galaxies-globular clusters (GCs) and halo field stars. This is generally taken as evidence of highly decoupled evolutionary histories between GC systems and their parent galaxies. Here we show, however, that new developments in linking the observed GC colors to their intrinsic metallicities suggest nonlinear color-to-metallicity conversions, which translate observed color distributions into strongly peaked, unimodal MDFs with broad metal-poor tails. Remarkably, the inferred GC MDFs are similar to the MDFs of resolved field stars in nearby elliptical galaxies and those produced by chemical evolution models of galaxies. The GC MDF shape, characterized by a sharp peak with a metal-poor tail, indicates a virtually continuous chemical enrichment with a relatively short timescale. The characteristic shape emerges across three orders of magnitude in the host galaxy mass, suggesting a universal process of chemical enrichment among various GC systems. Given that GCs are bluer than field stars within the same galaxy, it is plausible that the chemical enrichment processes of GCs ceased somewhat earlier than that of the field stellar population, and if so, GCs preferentially trace the major, vigorous mode of star formation events in galactic formation. We further suggest a possible systematic age difference among GC systems, in that the GC systems in more luminous galaxies are older. This is consistent with the downsizing paradigm whereby stars of brighter galaxies, on average, formed earlier than those of dimmer galaxies; this additionally supports the similar nature shared by GCs and field stars. Although the sample used in this study (the Hubble Space Telescope Advanced Camera for Surveys/Wide Field Channel, WFPC2, and WFC3 photometry for the GC systems in the Virgo galaxy cluster) confines our discussion to R {approx}< R{sub e} for giant ellipticals and {approx}<10 R{sub e} for normal ellipticals, our findings suggest that GC systems and their parent galaxies have shared a more common origin than previously thought, and hence greatly simplify theories of galaxy formation.

79 ASTRONOMY AND ASTROPHYSICS↗

Optics of colloidal quantum-confined CdSe nanoscrolls

Nanostructures in the form of 1.2-nm-thick colloidal CdSe nanoplatelets rolled into scrolls are investigated. The morphology of these scrolls is analysed and their basic geometric parameters are determined (diameter 29 nm, longitudinal size 100 – 150 nm) by TEM microscopy. Absorption and photoluminescence spectra of these objects are recorded, and the luminescence decay kinetics is studied. It is shown that the optical properties of CdSe nanoscrolls differ significantly from the properties of CdSe quantum dots and that these nanoscrolls are attractive for nanophotonic devices due to large oscillator strengths of the transition, small widths of excitonic peaks and short luminescence decay times. Nanoscrolls can be used to design hybrid organic–inorganic pure-color LEDs with a high luminescence quantum yield and low operating voltages. (optics and technology of nanostructures)

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Low-level water vapor fields from the VISSR Atmospheric Sounder (VAS) 'split window' channels

A simple physical algorithm is presented which calculates the water vapor content of the lower troposphere from the 11 and 12 micron (split window) channels on the VISSR Atmospheric Sounder (VAS) on the Geostationary Operational Environmental Satellites. The algorithm is used to analyze a time series of VAS split window radiances observed at 15 km horizontal resolution over eastern North America during a 12 hr period on 13 July 1981. Results of the color coded images of the derived precipitable water fields are found to show vivid water vapor features whose broad structure and evolution are verified by the radiosonde and surface networks. The satellite moisture fields also show significant mesoscale features and rapid developments which are not resolved by the conventional networks. The VAS split window is determined to clearly differentiate those areas in which water vapor extends over a deep layer and is more able to support convective cells from those areas in which water vapor is confined to a shallow layer and is therefore less able to support convection. It is concluded that the VAS split windows can be used operationally to monitor mesoscale developments in the low-level moisture fields over relatively cloud-free areas of the United States.

Chesters, D.↗

Upgrade of the infrared camera diagnostics for the JET ITER-like wall divertor

For the new ITER-like wall at JET, two new infrared diagnostics (KL9B, KL3B) have been installed. These diagnostics can operate between 3.5 and 5 {mu}m and up to sampling frequencies of {approx}20 kHz. KL9B and KL3B image the horizontal and vertical tiles of the divertor. The divertor tiles are tungsten coated carbon fiber composite except the central tile which is bulk tungsten and consists of lamella segments. The thermal emission between lamellae affects the surface temperature measurement and therefore KL9A has been upgraded to achieve a higher spatial resolution (by a factor of 2). A technical description of KL9A, KL9B, and KL3B and cross correlation with a near infrared camera and a two-color pyrometer is presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

On the Origin of Room-Temperature Amplified Spontaneous Emission in CsPbBr 3 Single Crystals

CsPbBr 3 is an all-inorganic halide perovskite with excellent photoluminescence (PL) properties for laser applications. Amplified spontaneous emission (ASE) is a prerequisite for lasing and typically observed from low-dimensional CsPbBr3 nanostructures, where quantum confinement enhances ASE. However, a gain medium for lasing should be prepared into a robust bulk form that works under intense light illumination. Here, we demonstrate that bulk CsPbBr 3 single crystals exhibit highly efficient ASE with a threshold of 46 MWcm -2 at 520 nm, if PL reabsorption via the indirect Rashba gap is properly suppressed by thickness control. Based on a series of spectroscopic and microscopic measurements, we show that this below-the-gap absorption can significantly alter the PL feature and even the apparent color of the crystal depending on the crystal size. Our results show that a thin CsPbBr 3 single crystal can be utilized for lasing applications when engineered into a submillimeter thickness for effective light–matter interaction.

36 MATERIALS SCIENCE↗

The distribution of rotational velocities for low-mass stars in the Pleiades

The available spectral type and color data for late-type Pleiades members have been reanalyzed, and new reddening estimates are obtained. New photometry for a small number of stars and a compilation of H-alpha equivalent widths for Pleiades dwarfs are presented. These data are used to examine the location of the rapid rotators in color-magnitude diagrams and the correlation between chromospheric activity and rotation. It is shown that the wide range of angular momenta exhibited by Pleiades K and M dwarfs is not necessarily produced by a combination of main-sequence spin-downs and a large age spread; it can also result from a plausible spread in initial angular momenta, coupled with initial main-sequence spin-down rates that are only weakly dependent on rotation. The new reddening estimates confirm Breger's (1985) finding of large extinctions confined to a small region in the southern portion of the Merope nebula.

Stauffer, John R.↗

Entanglement entropy of a color flux tube in (2+1)D Yang-Mills theory

We construct a novel flux tube entanglement entropy (FTE 2 ), defined as the excess entanglement entropy relative to the vacuum of a region of color flux stretching between a heavy quark-anti-quark pair in pure gauge Yang-Mills theory. We show that FTE 2 can be expressed in terms of correlators of Polyakov loops, is manifestly gauge-invariant, and therefore free of the ambiguities in computations of the entanglement entropy in gauge theories related to the choice of the center algebra. Employing the replica trick, we compute FTE 2 for SU(2) Yang-Mills theory in (2+1)D and demonstrate that it is finite in the continuum limit. We explore the properties of FTE 2 for a half-slab geometry, which allows us to vary the width and location of the slab, and the extent to which the slab cross-cuts the color flux tube. Following the intuition provided by computations of FTE 2 in (1+1)D, and in a thin string model, we examine the extent to which our FTE 2 results can be interpreted as the sum of an internal color entropy and a vibrational entropy corresponding to the transverse excitations of the string.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

THE MICROARCSECOND STRUCTURE OF AN ACTIVE GALACTIC NUCLEUS JET VIA INTERSTELLAR SCINTILLATION

We describe a new tool for studying the structure and physical characteristics of ultracompact active galactic nucleus (AGN) jets and their surroundings with {mu}as precision. This tool is based on the frequency dependence of the light curves observed for intra-day variable radio sources, where the variability is caused by interstellar scintillation. We apply this method to PKS 1257-326 to resolve the core-shift as a function of frequency on scales well below {approx}12 {mu}as. We find that the frequency dependence of the position of the scintillating component is r{proportional_to}{nu}{sup -0.1{+-}0.24} (99% confidence interval) and the frequency dependence of the size of the scintillating component is d{proportional_to}{nu}{sup -0.64{+-}0.006}. Together, these results imply that the jet opening angle increases with distance along the jet: d{proportional_to}r{sup n{sub d}} with n{sub d} > 1.8. We show that the flaring of the jet, and flat frequency dependence of the core position is broadly consistent with a model in which the jet is hydrostatically confined and traversing a steep pressure gradient in the confining medium with p{proportional_to}r{sup -n{sub p}} and n{sub p} {approx}> 7. Such steep pressure gradients have previously been suggested based on very long baseline interferometry studies of the frequency dependent core shifts in AGNs.

79 ASTRONOMY AND ASTROPHYSICS↗

Higgs-confinement transitions in QCD from symmetry protected topological phases

In gauge theories with fundamental matter there is typically no sharp way to distinguish confining and Higgs regimes, e.g. using generalized global symmetries acting on loop order parameters. It is standard lore that these two regimes are continuously connected, as has been explicitly demonstrated in certain lattice and continuum models. We point out that Higgsing and confinement sometimes lead to distinct symmetry protected topological (SPT) phases -- necessarily separated by a phase transition -- for ordinary global symmetries. We present explicit examples in 3+1 dimensions, obtained by adding elementary Higgs fields and Yukawa couplings to QCD while preserving parity P and time reversal T. In a suitable scheme, the confining phases of these theories are trivial SPTs, while their Higgs phases are characterized by non-trivial P- and T-invariant theta-angles θ f , θ g = π for flavor or gravity background gauge fields, i.e. they are topological insulators or superconductors. Finally, we consider conventional three-flavor QCD (without elementary Higgs fields) at finite U(1) B baryon-number chemical potential μ B , which preserves P and T. At very large μ B , three-flavor QCD is known to be a completely Higgsed color superconductor that also spontaneously breaks U(1) B . We argue that this high-density phase is in fact a gapless SPT, with a gravitational theta-angle θ g = π that safely co-exists with the U(1) B Nambu-Goldstone boson. We explain why this SPT motivates unexpected transitions in the QCD phase diagram, as well as anomalous surface modes at the boundary of quark-matter cores inside neutron stars.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

HST WFC3 Observations of Uranus' 2014 Storm Clouds and Comparison with VLT/SINFONI and IRTF/Spex Observations

In November 2014 Uranus was observed with the Wide Field Camera 3 (WFC3) instrument of the Hubble Space Telescope as part of the Hubble 2020: Outer Planet Atmospheres Legacy program, OPAL. OPAL annually maps Jupiter, Uranus and Neptune (and will also map Saturn from 2018) in several visible near- infrared wavelength filters. The Uranus 2014 OPAL observations were made on the 89th November at a time when a huge cloud complex, first observed by de Pater et al. (2015) and subsequently tracked by professional and amateur astronomers (Sayanagi et al., 2016), was present at 30-40deg N. We imaged the entire visible atmosphere, including the storm system, in seven filters spanning 467924 nm, capturing variations in the coloration of Uranus clouds and also vertical distribution due to wavelength dependent changes in Rayleigh scattering and methane absorption optical depth. Here we analyse these new HST observations with the NEMESIS radiative-transfer and retrieval code in multiple-scattering mode to determine the vertical cloud structure in and around the storm cloud system. The same storm system was also observed in the H-band (1.4-1.8 micrometers) with the SINFONI Integral Field Unit Spectrometer on the Very Large Telescope (VLT) on 31st October and 11th November, reported by Irwin et al. (2016, 10.1016j.icarus.2015.09.010). To constrain better the cloud particle sizes and scattering properties over a wide wavelength range we also conducted a limb-darkening analysis of the background cloud structure in the 30-40deg N latitude band by simultaneously fitting: a) these HSTOPAL observations at a range of zenith angles; b) the VLTSINFONI observations at a range of zenith angles; and c) IRTFSpeX observations of this latitude band made in 2009 at a single zenith angle of 23deg, spanning the wavelength range 0.8-1.8 micrometers (Irwin et al., 2015, 10.1016j.icarus.2014.12.020). We find that the HST observations, and the combined HSTVLTIRTF observations at all locations are well modelled with a three-component cloud comprised of: 1) a vertically thin, but optically thick deep tropospheric cloud at a pressure of approximately 2 bars; 2) a methane-ice cloud based at the methane-condensation level of approximately 1.23 bar, with variable vertical extent; and 3) a vertically extended tropospheric haze, also based at the methane-condensation level of 1.23 bar. We find that modelling both haze and tropospheric cloud with particles having an effective radius of approximately 0.1 micron provides a good fit the observations, although for the tropospheric cloud, particles with an effective radius as large as 1.0 micron provide a similarly good fit. We find that the particles in both the tropospheric cloud and haze are more scattering at short wave- lengths, giving them a blue color, but are more absorbing at longer wavelengths, especially for the tropospheric haze. We find that the spectra of the storm clouds are well modelled by localized thickening and vertical extension of the methane-ice cloud. For the particles in the storm clouds, which we assume to be composed of methane ice particles, we find that their mean radii must lie somewhere in the range 0. 1 1. 0 m. We find that the high clouds have low integrated opacity, and that streamers reminiscent of convective thunderstorm anvils are confined to levels deeper than 1 bar. These results argue against vigorous moist convective origins for the cloud features.

atmospheres↗

A detailed investigation on the impact of post-growth annealing on the materials and device characteristics of 35-layer In{sub 0.50}Ga{sub 0.50}As/GaAs quantum dot infrared photodetector with quaternary In{sub 0.21}Al{sub 0.21}Ga{sub 0.58}As capping

Highlights: ► We investigated the effect of ex situ annealing on InGaAs/GaAs QDIP with InAlGaAs layer. ► As-grown defect was removed by using post-growth annealing treatment. ► Increase in the compressive strain due to annealing is calculated from XRD curve. ► Three-fold enhancement in responsivity is observed in the QDIPs annealed at 650 °C. ► Two-fold enhancement in D* is observed sample annealed at 650 °C compared to as grown. -- Abstract: The effect of post-growth rapid thermal annealing on 35-layer In{sub 0.50}Ga{sub 0.50}As/GaAs quantum dot infrared photodetector (QDIP) with quaternary In{sub 0.21}Al{sub 0.21}Ga{sub 0.58}As capping has been investigated. Transmission electron microscopy showed some as-grown defects were removed by post growth annealing treatment. An increase in the compressive strain in the heterostructure due to annealing was identified from X-ray diffraction curve. A two-color photoresponse in the long-wave region (8.5 and 10.2 μm) was observed in both as-grown device and those annealed at 650 °C temperature. A three-fold enhancement in peak responsivity was observed in the QDIPs annealed at 650 °C (1.19 A/W) compared to that in the as-grown (0.34 A/W). Detectivity also increased by two fold from as-grown to 650 °C annealed device. The changes are attributed to the removal of as-grown defects and dislocations during epitaxial growth. These removals changed the confinement potential profile, which resulted in an improvement in the detectivity and responsivity of the annealed sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photoluminescence and Confinement of Excitons in Disordered Porous Films

The exciton confinement effect in quantum dots at the surface of SiO{sub 2} spheres and the percolation phase transition in films based on a mixture of pure SiO{sub 2} spheres and spheres covered by CdS quantum dots (SiO{sub 2}/CdS nanoparticles) are studied. It is found that, due to the high surface energy of spheres, the quantum dots deposited onto their surface are distorted, which modifies the exciton confinement effect: the effect is retained only in one direction, the direction normal to the surface of the spheres. As a result, the energy of the exciton ground state exhibits a complex dependence on both the quantum-dot radius and sphere size. In the optical spectra of films based on this mixture, the clustering of small-sized nanoparticles and then, at a critical concentration of nanoparticles of ~60%, the formation of a percolation cluster are detected for the first time. The critical concentration is twice higher than the corresponding quantity given by the model of geometrical “colored percolation”, which is a consequence of interaction between submicrometer nanoparticles. The relation between the basic parameters of the percolation transition, such as the film porosity, coordination number, and the quantity defining the number of particles in the percolation cluster, is obtained and analyzed.

36 MATERIALS SCIENCE↗

Corrugated Quantum Well Infrared Photodetectors and Arrays

Quantum well infrared photodetectors (QWIPs) have many advantages in infrared detection, mainly due to the mature Ill-V material technology. The employment of the corrugation structure further advances the technology by providing a simple, yet efficient light-coupling scheme. A C-QWIP enjoys the same flexibility as a detector with intrinsic normal incident absorption. In this paper, we will discuss the utilities of C-QWIPs in different applications, including two-color detection and polarization-sensitive detection. Besides practical applications, C-QWIPs are also useful in detector characterization. They can be used for measuring the absorption coefficient of light propagating parallel to the layers under bias and providing information on the energy resolved photoconductive gain. These two quantities have never been measured before. Based on the corrugation design, we have made several modifications that further improve the detector sensitivity without increasing its complexity. Other than the C-QWIP structure, we also continue searching for other sensitive detector architectures. In a quantum grid infrared photodetector, 3-dimensional electron confinement can be achieved, with which the detector is able to absorb light in all directions. At the same time, the photoconductive gain can also be improved. We further improve the design using a blazed structure. All the experimental results are supported by a rigorous electromagnetic modal transmission-line theory developed especially for these types of structures. Preliminary thermal imaging using C-QWIP FPAs validates the advantages of the present approach.

Choi, K. K.↗