Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cleaned”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Novel method for cleaning a vacuum chamber from hydrocarbon contamination

A novel method for cleaning a high vacuum chamber is presented. This method is based on concurrent in situ high-energetic UV light activation of contaminants located in the residual gas and at the vacuum chamber surfaces as well as the in situ generation of highly reactive ozone. Ozone oxidizes the contaminants to volatile species. Investigations by energy-dispersive x-ray analysis of residual gas depositions and mass-spectroscopy measurements of the residual gas in the vacuum chamber identify the contaminant species as hydrocarbons. After a cleaning period of 8 h, a decrease in measured chamber contamination by about 90% could be achieved according to atomic force microscope analysis. Mass spectroscopy measurements using a residual gas analyzer indicate the creation of volatile, carbonaceous species during the cleaning process.

36 MATERIALS SCIENCE↗

Damage by radicals and photons during plasma cleaning of porous low-k SiOCH. I. Ar/O{sub 2} and He/H{sub 2} plasmas

Porous dielectric materials offer lower capacitances that reduce RC time delays in integrated circuits. Typical porous low dielectric (low-k) materials include SiOCH-silicon dioxide with carbon groups, principally -CH{sub 3}, lining the pores. Fluorocarbon plasmas are often used to etch such low-k materials. These processes leave a fluorocarbon polymer on the SiOCH surface that must be removed, often with oxygen or hydrogen containing plasmas. Pores open to the surface and that are internally connected provide pathways for reactive species to enter into the porous network and produce damage. For example, during cleaning using O{sub 2} containing plasmas, reactions of O atoms with -CH{sub 3} groups can increase the k-value by removing C atoms. Vacuum ultraviolet (VUV) photons produced by the plasma and that penetrate into the material can scission -Si-CH{sub 3} bonds and accelerate the removal of -CH{sub 3} groups. This paper reports on results from a computational investigation of Ar/O{sub 2} and He/H{sub 2} plasma cleaning of porous SiOCH when including the effects of VUV photons. The authors found that He/H{sub 2} plasmas are able to clean CF{sub x} polymers deposited during etching while producing milder damage to underlying -CH{sub 3} sites compared to O{sub 2} plasmas due to the lower reactivity of H atoms and the shorter penetration distance of photons produced in He/H{sub 2} plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

As-Received, Ozone Cleaned and Ar+ Sputtered Surfaces of Hafnium Oxide Grown by Atomic Layer Deposition and Studied by XPS

In this study, X-ray photoelectron spectroscopy (XPS) characterization was performed on 47 nm thick hafnium oxide (HfO{sub 2}) films grown by atomic layer deposition using TEMA-Hf/H{sub 2}O at 250 C substrate temperature. HfO{sub 2} is currently being studied as a possible replacement for Silicon Oxide (SiO{sub 2}) as a gate dielectric in electronics transistors. XPS spectra were collected on a Physical Electronics Quantum 2000 Scanning ESCA Microprobe using a monochromatic Al K{sub a} X-ray (1486.7 eV) excitation source. The sample was analyzed under the following conditions: as received, after UV irradiation for five minutes, and after sputter cleaning with 2 kV Ar{sup +} ions for 180 seconds. Survey scans showed carbon, oxygen, and hafnium as the major species in the film, while the only minor species of argon and carbide was detected after sputtering. Adventitious carbon initially composed approximately 18.6 AT% of the surface, but after UV cleaning it was reduced to 2.4 AT%. This demonstrated that that the majority of carbon was due to adventitious carbon. However, after 2 kV Ar{sup +} sputtering there was still only trace amounts of carbon at {approx}1 AT%, Some of this trace carbon is now in the form of a carbide due to the interaction with Ar{sup +} used for sputter cleaning. Furthermore, the stoiciometric ratio of oxygen and hafnium is consistent with a high quality HfO{sub 2} film.

36 MATERIALS SCIENCE↗

Cleaning of inner vacuum surfaces in the Uragan-3M facility by radio-frequency discharges

A method for cleaning vacuum surfaces by a low-temperature (T{sub e} ∼ 10 eV) relatively dense (n{sub e} ≈ 10{sup 12} cm{sup −3}) plasma of an RF discharge was developed and successfully applied at the Uragan-3M torsatron. The convenience of the method is that it can be implemented with the same antenna system and RF generators that are used to produce and heat the plasma in the operating mode and does not require retuning the frequencies of the antennas and RF generators. The RF discharge has a high efficiency from the standpoint of cleaning vacuum surfaces. After performing a series of cleanings by the low-temperature RF discharge plasma (about 20000 pulses), (i) the intensity of the CIII impurity line was substantially reduced, (ii) a quasi-steady operating mode with a duration of up to 50 ms, a plasma density of n{sub e} ≈ 10{sup 12} cm{sup −3}, and an electron temperature of up to T{sub e} ∼ 1 keV was achieved, and (iii) mass spectrometric analysis of the residual gas in the chamber indicated a significant reduction in the impurity content.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recipes for a Successful Exit for Clean- and Hard-tech Startups

This study demonstrates the combinations of multiple causal factors that formulate a startup’s strategy to successfully “exit”, namely “recipes for a successful exit,” in the clean- and hard-tech sector. We identify seven key causal factors (i.e., causal conditions) that impact startup success, including commercial readiness, investor interactions, favorable industry, non-financial support, straightforward development path, experienced team, and visibility to investors. We also investigate the combinations of selective causal conditions that can provide further synergetic impact. We conduct the fuzzy-set qualitative comparative analysis (fsQCA) on seven US clean and hard-tech startups that exited between 2005 and 2016. The successful companies all demonstrate distinctive characteristics based on three general categories (1) robust ecosystem; (2) heavy-lifting team; or (3) external opportunity. Across these three categories, commercial readiness and strong investor interactions are necessary conditions for all exit cases. But there are important differences that drive success in each category, such as the interaction with non-financial support (in the robust ecosystem case), experienced team (in the heavy-lifting team case), and favorable industry (in the external opportunity case). Furthermore, our findings are meant to support entrepreneurs in reaching an exit by optimizing the given internal and external circumstances, and policymakers to build a robust ecosystem that can increase the success rate of the clean- and hardtech development.

99 GENERAL AND MISCELLANEOUS↗

ALTERNATIVE AND ENHANCED CHEMICAL CLEANING: BASIC STUDIES RESULTS FY2010

In an effort to develop and optimize chemical cleaning methods for the removal of sludge heels from High Level Waste tanks, solubility tests have been conducted using nonradioactive, pure metal phases. The metal phases studied included the aluminum phase gibbsite and the iron phases hematite, maghemite, goethite, lepidocrocite, magnetite, and wustite. Many of these mineral phases have been identified in radioactive, High Level Waste sludge at the Savannah River and Hanford Sites. Acids evaluated for dissolution included oxalic, nitric, and sulfuric acids and a variety of other complexing organic acids. The results of the solubility tests indicate that mixtures of oxalic acid with either nitric or sulfuric acid are the most effective cleaning solutions for the dissolution of the primary metal phases in sludge waste. Based on the results, optimized conditions for hematite dissolution in oxalic acid were selected using nitric or sulfuric acid as a supplemental proton source. Electrochemical corrosion studies were also conducted (reported separately; Wiersma, 2010) with oxalic/mineral acid mixtures to evaluate the effects of these solutions on waste tank integrity. The following specific conclusions can be drawn from the test results: (1) Oxalic acid was shown to be superior to all of the other organic acids evaluated in promoting the dissolution of the primary sludge phases. (2) All iron phases showed similar solubility trends in oxalic acid versus pH, with hematite exhibiting the lowest solubility and the slowest dissolution. (3) Greater than 90% hematite dissolution occurred in oxalic/nitric acid mixtures within one week for two hematite sources and within three weeks for a third hematite sample with a larger average particle size. This dissolution rate appears acceptable for waste tank cleaning applications. (4) Stoichiometric dissolution of iron phases in oxalic acid (based on the oxalate concentration) and the formation of the preferred 1:1 Fe to oxalate complex is possible with the addition of a supplemental hydrogen ion source (HNO{sub 3} or H{sub 2}SO{sub 4}) and pH control. (5) Sulfuric acid is nearly twice as effective as nitric acid (on a molar basis) at promoting hematite dissolution in oxalic acid solutions, most likely due to the fact that it is diprotic. (6) The greater the oxalic acid concentration, the greater the demand for supplemental H{sup +} to promote optimal dissolution. Minimum mineral acid concentrations required for optimal oxalic acid utilization based on hematite solubility tests are provided. (7) Corrosion studies conducted (reported elsewhere) with 1 wt.% oxalic acid revealed that carbon steel corrosion rates are manageable at lower mineral acid concentrations (0.1 M HNO{sub 3} and 0.05 M H{sub 2}SO{sub 4}) and lower temperatures (45 C). (8) Proposed conditions for waste tank heel dissolution based on the solubility and corrosion test results are 0.5 wt.% oxalic acid and 0.18 M HNO{sub 3} or 0.09 M H{sub 2}SO{sub 4} at 50 C. (9) The OLI Thermodynamic Model appears to over-predict the solubility of the iron phases studied in oxalic acid and oxalic/nitric acid mixtures. The predictions show better agreement with experimental results at higher pH and in sulfuric/oxalic acid mixtures. (10) Oxalic, nitric, and sulfuric acids are effective at quickly dissolving gibbsite ({ge}86% dissolution in 2 weeks), with oxalic/sulfuric acid mixtures being particularly effective. (11) Limited dissolution tests conducted with carbon steel coupons revealed that the presence of metallic iron can, in some cases, result in dramatically different results. Additional studies in this area are recommended. Based on the current results, the optimal approach for the removal of sludge heels for HLW tanks would include the following steps: (1) removal of the maximum possible amount of heel materials by mechanical means; (2) neutralization and acidification of the heel using dilute mineral acid (This step should promote significant dissolution of certain metal hydroxides and salts, including gibbsite.); and (3) dissolution of the residual heel material at 50 C using an acid mixture containing 0.5 wt.% oxalic acid and 0.18 M nitric acid (This step should dissolve the iron phases.)

36 MATERIALS SCIENCE↗

State of the States 2010: The Role of Policy in Clean Energy Market Transformation

This report builds on the emerging body of literature seeking to identify quantitative connections between clean energy policy and renewable energy. The methods presented test the relationships between a broad set of policies and clean energy resources (energy efficiency, biomass, geothermal, solar, and wind). Energy efficiency findings are an initial foray into this type of analysis and indicatesignificant connections between reduced energy use and buildings codes, energy efficiency resource standards (in some cases), and electricity price. Renewable energy findings specify that there is most often a relationship between state policies and solar and wind development, indicating that while policies might apply to a wide variety of renewable resources, further tailoring of policyspecifics to resource needs may lead to increased development of a wider variety of renewable energy resources. Further research is needed to refine the connections between clean energy development and policy, especially in the area of the impact of the length of time that a policy has been in place.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

ANALYSIS OF SAMPLES FROM TANK 6F CHEMICAL CLEANING

Savannah River Remediation (SRR) is preparing Tank 6F for closure. The first step in preparing the tank for closure is mechanical sludge removal. In mechanical sludge removal, personnel add liquid (e.g., inhibited water or supernate salt solution) to the tank to form a slurry. They mix the liquid and sludge with pumps, and transfer the slurry to another tank for further processing. Mechanical sludge removal effectively removes the bulk of the sludge from a tank, but is not able to remove all of the sludge. In Tank 6F, SRR estimated a sludge heel of 5,984 gallons remained after mechanical sludge removal. To remove this sludge heel, SRR performed chemical cleaning. The chemical cleaning included two oxalic acid strikes, a spray wash, and a water wash. SRR conducted the first oxalic acid strike as follows. Personnel added 110,830 gallons of 8 wt % oxalic acid to Tank 6F and mixed the contents of Tank 6F with two submersible mixer pumps (SMPs) for approximately four days. Following the mixing, they transferred 115,903 gallons of Tank 6F material to Tank 7F. The SMPs were operating when the transfer started and were shut down approximately five hours after the transfer started. SRR collected a sample of the liquid from Tank 6F and submitted it to SRNL for analysis. Mapping of the tank following the transfer indicated that 2,400 gallons of solids remained in the tank. SRR conducted the second oxalic acid strike as follows. Personnel added 28,881 gallons of 8 wt % oxalic acid to Tank 6F. Following the acid addition, they visually inspected the tank and transferred 32,247 gallons of Tank 6F material to Tank 7F. SRR collected a sample of the liquid from Tank 6F and submitted it to SRNL for analysis. Mapping of the tank following the transfer indicated that 3,248 gallons of solids remained in the tank. Following the oxalic acid strikes, SRR performed Spray Washing with oxalic acid to remove waste collected on internal structures, cooling coils, tank top internals, and tank walls. The Acid Spray Wash was followed by a Water Spray Wash to remove oxalic acid from the tank internals. SRR conducted the Spray Wash as follows. Personnel added 4,802 gallons of 8 wt % oxalic acid to Tank 6F through the spray mast installed in Riser 2, added 4,875 gallons of oxalic acid through Riser 7, added 5,000 gallons of deionized water into the tank via Riser 2, and 5,000 gallons of deionized water into the tank via Riser 7. Following the Spray Wash, they visually inspected the tank and transferred 22,430 gallons of Tank 6F material to Tank 7F. SRR collected a sample of the liquid from Tank 6F and submitted it to SRNL for analysis. Following the Spray Wash and transfer, Savannah River Site (SRS) added 113,935 gallons of well water to Tank 6F. They mixed the tank contents with a single SMP and transferred 112,699 gallons from Tank 6F to Tank 7F. SRR collected a sample of the liquid from Tank 6F and submitted to SRNL for analysis. Mapping of the tank following the transfer indicated that 3,488 gallons of solids remained in the tank. Following the Water Wash, SRR personnel collected a solid sample and submitted it to SRNL for analysis to assess the effectiveness of the chemical cleaning and to provide a preliminary indication of the composition of the material remaining in the tank.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

TREATMENT TANK OFF-GAS TESTING FOR THE ENHANCED CHEMICAL CLEANING PROCESS

The purpose of this activity was to provide a bounding estimate of the volume of hydrogen gas generated during Enhanced Chemical Cleaning (ECC) of residual sludge remaining in a Type I or Type II treatment tank as well as to provide results independent of the sludge volume in the waste tank to be cleaned. Previous testing to support Chemical Cleaning was based on a 20:1 oxalic acid to sludge ratio. Hydrogen gas evolution is the primary safety concern. Sealed vessel coupon tests were performed to estimate the hydrogen generation rate due to corrosion of carbon steel by 2.5 wt.% oxalic acid. These tests determined the maximum instantaneous hydrogen generation rate, the rate at which the generation rate decays, and the total hydrogen generated. These values were quantified based on a small scale methodology similar to the one described in WSRC-STI-2007-00209, Rev. 0. The measured rates support identified Safety Class functions. The tests were performed with ASTM A285 Grade C carbon steel coupons. Bounding conditions were determined for the solution environment. The oxalic acid concentration was 2.5 wt.% and the test temperature was 75 C. The test solution was agitated and contained no sludge simulant. Duplicate tests were performed and showed excellent reproducibility for the hydrogen generation rate and total hydrogen generated. The results showed that the hydrogen generation rate was initially high, but decayed rapidly within a couple of days. A statistical model was developed to predict the instantaneous hydrogen generation rate as a function of exposure time by combining both sets of data. An upper bound on the maximum hydrogen generation rate was determined from the upper 95% confidence limit. The upper bound confidence limit for the hydrogen generation rate is represented by the following equation. ln (G{sub v}) = -8.22-0.0584 t + 0.0002 t{sup 2}. This equation should be utilized to estimate the instantaneous hydrogen generation rate per unit surface area, G{sub v}, at a given time, t. The units for G{sub v} and t are ft{sup 3}/ft{sup 2}/min and hours, respectively. The total volume of hydrogen gas generated during the test was calculated from the model equation. An upper bound on the total gas generated was determined from the upper 95% confidence limit. The upper bound limit on the total hydrogen generated during the 163 hour test was 0.332 ft{sup 3}/ft{sup 2}. The maximum instantaneous hydrogen generation rate for this scenario is greater than that previously measured in the 8 wt.% oxalic acid tests due to both the absence of sludge in the test (i.e., greater than 20:1 ratio of acid to sludge) and the use of polished coupons (vs. mill scale coupons). However, due to passivation of the carbon steel surface, the corrosion rate decays by an order of magnitude within the first three days of exposure such that the instantaneous hydrogen generation rates are less than that previously measure in the 8 wt.% oxalic acid tests. While the results of these tests are bounding, the conditions used in this study may not be representative of the ECC flowsheet, and the applicability of these results to the flowsheet should be evaluated for the following reasons: (1) The absence of sludge results in higher instantaneous hydrogen generation rates than when the sludge is present; and (2) Polished coupons do not represent the condition of the carbon steel interior of the tank, which are covered with mill scale. Based on lower instantaneous corrosion rates measured on mill scale coupons exposed to oxalic acid, lower instantaneous hydrogen generation rates are expected for the tank interior than measured on the polished coupons. Corrosion rates were determined from the coupon tests and also calculated from the measured hydrogen generation rates. Excellent agreement was achieved between the time averaged corrosion rate calculated from the hydrogen generation rates and the corrosion rates determined from the coupon tests. The corrosion rates were on the order of 18 to 28 mpy. Good agreement was also observed between the maximum instantaneous corrosion rate as calculated from the hydrogen generation rate and the corrosion rate determined by previous electrochemical tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Clean Cities 2012 Annual Metrics Report

The U.S. Department of Energy's (DOE) Clean Cities program advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. A national network of nearly 100 Clean Cities coalitions brings together stakeholders in the public and private sectors to deploy alternative and renewable fuels, idle-reduction measures, fuel economy improvements, and new transportation technologies, as they emerge. Each year DOE asks Clean Cities coordinators to submit annual reports of their activities and accomplishments for the previous calendar year. Data and information are submitted via an online database that is maintained as part of the Alternative Fuels Data Center (AFDC) at the National Renewable Energy Laboratory (NREL). Coordinators submit a range of data that characterizes the membership, funding, projects, and activities of their coalitions. They also submit data about sales of alternative fuels, deployment of alternative fuel vehicles (AFVs) and hybrid electric vehicles (HEVs), idle-reduction initiatives, fuel economy activities, and programs to reduce vehicle miles traveled (VMT). NREL analyzes the data and translates them into petroleum-use reduction impacts, which are summarized in this report.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Materials Science Clean Room Facility at Tulane University (Final Technical Report)

The project involves conversion of a 3,000 sq. ft. area into a clean room facility for materials science research. It will be accomplished in phases. Phase I will involve preparation of the existing space, acquisition and installation of clean room equipped with a pulsed laser deposition (PLD) processing system, and conversion of ancillary space to facilitate the interface with the clean room. From a capital perspective, Phases II and III will involve the acquisition of additional processing, fabrication, and characterization equipment and capabilities.

36 MATERIALS SCIENCE↗

State of the States 2010: The Role of Policy in Clean Energy Market Transformation

This report builds on the emerging body of literature seeking to identify quantitative connections between clean energy policy and renewable energy. The methods presented test the relationships between a broad set of policies and clean energy resources (energy efficiency, biomass, geothermal, solar, and wind). Energy efficiency findings are an initial foray into this type of analysis and indicate significant connections between reduced energy use and buildings codes, energy efficiency resource standards (in some cases), and electricity price. Renewable energy findings specify that there is most often a relationship between state policies and solar and wind development, indicating that while policies might apply to a wide variety of renewable resources, further tailoring of policy specifics to resource needs may lead to increased development of a wider variety of renewable energy resources. Further research is needed to refine the connections between clean energy development and policy, especially in the area of the impact of the length of time that a policy has been in place.

09 BIOMASS FUELS↗

Clean Energy in City Codes: A Baseline Analysis of Municipal Codification across the United States

Municipal governments in the United States are well positioned to influence clean energy (energy efficiency and alternative energy) and transportation technology and strategy implementation within their jurisdictions through planning, programs, and codification. Municipal governments are leveraging planning processes and programs to shape their energy futures. There is limited understanding in the literature related to codification, the primary way that municipal governments enact enforceable policies. The authors fill the gap in the literature by documenting the status of municipal codification of clean energy and transportation across the United States. More directly, we leverage online databases of municipal codes to develop national and state-specific representative samples of municipal governments by population size. Our analysis finds that municipal governments with the authority to set residential building energy codes within their jurisdictions frequently do so. In some cases, communities set codes higher than their respective state governments. Examination of codes across the nation indicates that municipal governments are employing their code as a policy mechanism to address clean energy and transportation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Clean Cities 2015 Annual Metrics Report

The U.S. Department of Energy's (DOE's) Clean Cities program advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use and greenhouse gas (GHG) emissions in transportation. A national network of nearly 100 Clean Cities coalitions, whose territory covers 80% of the U.S. population, brings together stakeholders in the public and private sectors to deploy alternative and renewable fuels, idle-reduction (IR) measures, fuel economy improvements, and new transportation technologies as they emerge. Each year, DOE asks Clean Cities coordinators to submit annual reports of their activities and accomplishments for the previous calendar year. Progress reports and information are submitted online as a function of the Alternative Fuels Data Center (AFDC) at the National Renewable Energy Laboratory (NREL). Coordinators report a range of information that characterize the membership, funding, projects, and activities of their coalitions. They also document activities in their region related to the development of refueling/charging infrastructure, sales of alternative fuels; deployment of alternative fuel vehicles (AFVs), plug-in electric vehicles (PEVs), hybrid electric vehicles (HEVs), and plug-in hybrid electric vehicles (PHEVs); idle reduction initiatives; fuel economy improvement activities; and programs to reduce vehicle miles traveled (VMT). NREL analyzes the data and translates them into petroleum-use and GHG emission reduction impacts, which are summarized in this report.

33 ADVANCED PROPULSION SYSTEMS↗

Clean Energy Manufacturing Analysis Center Benchmark Report: Framework and Methodologies

This report documents the CEMAC methodologies for developing and reporting annual global clean energy manufacturing benchmarks. The report reviews previously published manufacturing benchmark reports and foundational data, establishes a framework for benchmarking clean energy technologies, describes the CEMAC benchmark analysis methodologies, and describes the application of the methodologies to the manufacturing of four specific clean energy technologies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Clean Cities Coalitions: 2016 Activity Report

The U.S. Department of Energy's (DOE's) national network of Clean Cities Coalitions advance the nation's economic, environmental, and energy security by supporting local actions to promote the use of domestic fuels within transportation. The nearly 100 Clean Cities coalitions, whose territory covers 80% of the U.S. population, bring together stakeholders in the public and private sectors to use alternative and renewable fuels, idle-reduction (IR) measures, fuel economy improvements, and new transportation technologies as they emerge. To ensure success, coalitions leverage a robust set of expert resources and tools provided by national laboratories and DOE. Each year, Clean Cities coordinators submit annual reports of their activities and accomplishments for the previous calendar year. Data and information are submitted via an online tool that is maintained as part of the Alternative Fuels Data Center (AFDC) at the National Renewable Energy Laboratory (NREL). Coordinators submit a range of data that characterize the membership, funding, projects, and activities of their coalitions. They also submit data about sales of alternative fuels; use of alternative fuel vehicles (AFVs), plug-in electric vehicles (PEVs), and hybrid electric vehicles (HEVs); IR initiatives; fuel economy improvement activities; and programs to reduce vehicle miles traveled (VMT). NREL analyzes the submitted data to determine how broadly energy use in the U.S. has shifted due to coalition activities, which are summarized in this report.

2016 metrics↗

Clean Cities Coalitions (2018 Activity Report)

Clean Cities coalition activities resulted in an energy use impact (EUI) of over 1 billion gasoline-gallons equivalent (GGE), comprised of net alternative fuels used and energy savings from efficiency projects, in 2018. Participation in vehicle and infrastructure development projects remained strong, as did alternative fuel use and resulting overall EUI. Clean Cities coalition activities reduce emissions as they impact energy use. Coalition-reported activities prevented 5 million carbon dioxide-equivalent tons of emissions (only greenhouse gas [GHG] emissions are reported here; criteria pollutants and other emissions are not included in this report). Coalitions were successful in securing project grant awards from numerous (non-DOE) outside sources. For other Federal, State, and local agencies and private sector foundations, see funding section on page 25. The 84 project grant awards in 2018 generated $251 million in funds from coalition members and project partners along with $1.9 million in DOE grant funds. Coalitions also collected $1.1 million in stakeholder dues and $2.9 million in operational funds from host organizations. In macro terms, this supplemental funding represents nearly a 7:1 leveraging of the $37.8 million that was included in the VTO Technology Integration budget in Fiscal Year 2018. Clean Cities coordinators spent nearly 121,000 hours pursuing their coalitions' goals in 2018. The average coordinator is quite experienced and has held his or her position for at least eight years. Coordinators logged more than 3,805 outreach, education, and training activities in 2018, which reached an estimated 35 million people.

33 ADVANCED PROPULSION SYSTEMS↗

Integration of Clean Energy into Oil Field Operations

Integrating clean energy into oil and gas operations could reduce emissions and maximize higher-value use of produced hydrocarbons. In this published study, analysts from the Joint Institute for Strategic Energy Analysis (JISEA) and the National Renewable Energy Laboratory (NREL) evaluated clean power technologies for an oil field in the Delaware Basin using NREL’s Renewable Energy Integration and Optimization, or REopt, tool. The analysts evaluated different configurations of distributed energy resources based on the technologies available and the load they could satisfy, available land, and hypothetical carbon pricing. The analysis is part of a collaborative program with industry to understand site-specific energy consumption and prices in the oil and gas supply chain and determine under what conditions clean energy options are economically attractive. This work was sponsored by a consortium including ConocoPhillips, Baker Hughes, Extraction Oil & Gas, Kinder Morgan, and the Interstate Natural Gas Association of America Foundation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗