SEARCH · Engineering Papers

Results for “Camber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1975

An analytical and experimental evaluation of airfoil sections for helicopter rotor application

The influence of the more independent airfoil parameters such as thickness, thickness distribution, leading-edge radius, camber, and camber distribution on lift-Mach number characteristics is investigated at lift coefficients up to near-maximum lift. The analysis is based on the drag divergence Mach number (Md) prediction techniques, where Md is the free-stream Mach number at which the rate of increase of drag coefficient with Mach number equals 0.1. The analytical results obtained indicate the compromises in Md which result from changes in thickness ratio, location of maximum thickness, leading edge radius, camber addition, and location of maximum camber for four- and five-digit airfoils and some six-series airfoils of potential interest for helicopters. An example of airfoil sections which combines several of the favorable geometric changes is evaluated analytically and experimentally. A comparison of results shows that the relative effect of the geometric changes on the lift coefficient-Md relation is realistic, and that the methods of analysis employed can be effectively used during preliminary vehicle design and airfoil selection.

Bingham, G. J.↗

NASA NTRS1984

Body and canard effects on an attached-flow maneuver wing at Mach 1.62

A wing-body-canard configuration was tested at a Mach number of 1.62 by using both a cambered and an uncambered wing. The cambered wing was designed to produce efficient high lift by using attached supercritical crossflow and was originally tested as an isolated wing. The uncambered wing has the same planform and essentially the same thickness distribution as the cambered wing. The experiment determined the effects of a body and canards on both wings. The experimental data showed that both the body and the canards influenced the wing pressure levels, but that the attached supercritical crossflow, which was achieved in the isolated cambered-wing test, was maintained in the presence of a body and canards. Tables of experimental pressure, force, and moment data are included, as well as photographs of oil flow patterns on the upper surface.

Pittman, J. L.↗

NASA NTRS1986

Mission Adaptive Wing test program

With the completion of the F-111 test-bed Mission Adaptive Wing (MAW) test program's manual flight control system, emphasis has been shifted to flight testing of MAW automatic control modes. These encompass (1) cruise camber control, (2) maneuver camber control, (3) maneuver load control, and (4) maneuver enhancement and load alleviation control. The aircraft is currently cleared to a 2.5-g maneuvering limit due to generally higher variable-incidence wing pivot loads than had been anticipated, especially at the higher wing-camber settings. Buffet is noted to be somewhat higher than expected at the higher camber settings.

Birk, Frank T.↗

NASA NTRS1988

Measured and predicted pressure distributions on the AFTI/F-111 mission adaptive wing

Flight tests have been conducted using an F-111 aircraft modified with a mission adaptive wing (MAW). The MAW has variable-camber leading and trailing edge surfaces that can change the wing camber in flight, while preserving smooth upper surface contours. This paper contains wing surface pressure measurements obtained during flight tests at Dryden Flight Research Facility of NASA Ames Research Center. Upper and lower surface steady pressure distributions were measured along four streamwise rows of static pressure orifices on the right wing for a leading-edge sweep angle of 26 deg. The airplane, wing, instrumentation, and test conditions are discussed. Steady pressure results are presented for selected wing camber deflections flown at subsonic Mach numbers up to 0.90 and an angle-of-attack range of 5 to 12 deg. The Reynolds number was 26 million, based on the mean aerodynamic chord. The MAW flight data are compared to MAW wind tunnel data, transonic aircraft technology (TACT) flight data, and predicted pressure distributions. The results provide a unique database for a smooth, variable-camber, advanced supercritical wing.

Webb, Lannie D.↗

NASA NTRS1990

An investigation of design optimization using a 2-D viscous flow code with multigrid

Computational fluid dynamics (CFD) codes have advanced to the point where they are effective analytical tools for solving flow fields around complex geometries. There is also a need for their use as a design tool to find optimum aerodynamic shapes. In the area of design, however, a difficulty arises due to the large amount of computer resources required by these codes. It is desired to streamline the design process so that a large number of design options and constraints can be investigated without overloading the system. There are several techniques which have been proposed to help streamline the design process. The feasibility of one of these techniques is investigated. The technique under consideration is the interaction of the geometry change with the flow calculation. The problem of finding the value of camber which maximizes the ratio of lift over drag for a particular airfoil is considered. In order to test out this technique, a particular optimization problem was tried. A NACA 0012 airfoil was considered at free stream Mach number of 0.5 with a zero angle of attack. Camber was added to the mean line of the airfoil. The goal was to find the value of camber for which the ratio of lift over drag is a maximum. The flow code used was FLOMGE which is a two dimensional viscous flow solver which uses multigrid to speed up convergence. A hyperbolic grid generation program was used to construct the grid for each value of camber.

Doria, Michael L.↗

NASA NTRS1991

A unified viscous theory of lift and drag of 2-D thin airfoils and 3-D thin wings

A unified viscous theory of 2-D thin airfoils and 3-D thin wings is developed with numerical examples. The viscous theory of the load distribution is unique and tends to the classical inviscid result with Kutta condition in the high Reynolds number limit. A new theory of 2-D section induced drag is introduced with specific applications to three cases of interest: (1) constant angle of attack; (2) parabolic camber; and (3) a flapped airfoil. The first case is also extended to a profiled leading edge foil. The well-known drag due to absence of leading edge suction is derived from the viscous theory. It is independent of Reynolds number for zero thickness and varies inversely with the square root of the Reynolds number based on the leading edge radius for profiled sections. The role of turbulence in the section induced drag problem is discussed. A theory of minimum section induced drag is derived and applied. For low Reynolds number the minimum drag load tends to the constant angle of attack solution and for high Reynolds number to an approximation of the parabolic camber solution. The parabolic camber section induced drag is about 4 percent greater than the ideal minimum at high Reynolds number. Two new concepts, the viscous induced drag angle and the viscous induced separation potential are introduced. The separation potential is calculated for three 2-D cases and for a 3-D rectangular wing. The potential is calculated with input from a standard doublet lattice wing code without recourse to any boundary layer calculations. Separation is indicated in regions where it is observed experimentally. The classical induced drag is recovered in the 3-D high Reynolds number limit with an additional contribution that is Reynold number dependent. The 3-D viscous theory of minimum induced drag yields an equation for the optimal spanwise and chordwise load distribution. The design of optimal wing tip planforms and camber distributions is possible with the viscous 3-D wing theory.

Yates, John E.↗

NASA NTRS1992

An aerodynamic design study of a series of lifting bodies at angles of attack from 10 to 53 degrees at Mach numbers from 2.30 to 4.62

The aerodynamic characteristics in the transition from high to low angles of attack at supersonic speeds have been experimentally and theoretically studied for a series of lifting bodies with various upper and lower surface camber designs. The configurations under consideration have a 75-degree swept delta planform with a rounded nose. Data obtained indicate that changes in the camber design cause some distinct changes in the aerodynamic characteristics that shoud be taken into account in the selection of a lifting body shape. The flat bottom designs with upper surface camber are found to provide greater drag for retardation at high angles of attack but are considerably out of trim longitudinally. The flat top designs with lower surface camber provide less drag at high angles of attack but can be more easily trimmed. Calculated results are found to be in good agreement with the experimental data.

Spearman, M. L.↗

NASA NTRS2004

Development of Micro Air Vehicle Technology With In-Flight Adaptive-Wing Structure

This is a final report on the research studies, "Development of Micro Air Vehicle Technology with In-Flight Adaptrive-Wing Structure". This project involved the development of variable-camber technology to achieve efficient design of micro air vehicles. Specifically, it focused on the following topics: 1) Low Reynolds number wind tunnel testing of cambered-plate wings. 2) Theoretical performance analysis of micro air vehicles. 3) Design of a variable-camber MAV actuated by micro servos. 4) Test flights of a variable-camber MAV.

Waszak, Martin R.↗

NASA NTRS1972

Effect of wing design on the longitudinal aerodynamic characteristics of a wing-body model at subsonic speeds

An investigation has been conducted to determine the effects of wing camber and twist on the longitudinal aerodynamic characteristics of a wingbody configuration. Three wings were used each having the same planform (aspect ratio of 2.5 and leading-edge sweep angle of 44 deg.) but differing in amounts of camber and twist (wing design lift coefficient). The wing design lift coefficients were 0, 0.35, and 0.70. The investigation was conducted over a Mach number range from 0.20 to 0.70 at angles of attack up to about 22 deg. The effect of wing strakes on the aerodynamic characteristics of the cambered wings was also studied. A comparison of the experimentally determined aerodynamic characteristics with theoretical estimates is also included.

Henderson, W. P.↗

NASA NTRS1974

An analysis of the impact of cabin floor angle restrictions on L/D for a typical supersonic transport

High floor angles at cruise have been identified as a significant problem facing airline and public acceptance of a supersonic transport. In order to explore the relationship between cruise performances and floor angle, four related wing-fuselage design and integration studies have been conducted. The studies were: (1) a fuselage camber study in which perturbations in the fuselage camber distribution were examined with a baseline wing, (2) a wing optimization study in which wings were optimized for minimum drag at C sub L's less than the design C sub L. These wings were optimized as wing planform camber surfaces alone and evaluated with a baseline fuselage, (3) a second wing optimization study in which wings were optimized for minimum drag at C sub L's less than the design C sub L but for this study the wings were optimized in the presence of the baseline fuselage, and (4) a third wing optimization study in which wings were optimized for minmum drag subject to C sub M constraints designed to produce more positive C sub MO's, thereby reducing trim drag. The studies indicated that it was not possible to both improve the aircraft cruise L/D and substantially reduce the cruise floor angle. The studies did indicate that the cruise floor angle could be reduced by reducing the fuselage incidence relative to the wing, but the reduction in floor angle was accompanied by a substantial reduction in L/D.

Radkey, R. L.↗

NASA NTRS1974

Effects of leading edge sweep angle and design lift coefficient on performance of a modified arrow wing at a design Mach number of 2.6

Wing models were tested in the high-speed section of the Langley Unitary Plan wind tunnel to study the effects of the leading-edge sweep angle and the design lift coefficient on aerodynamic performance and efficiency. The models had leading-edge sweep angles of 69.44 deg, 72.65 deg, and 75.96 deg which correspond to values of the design Mach-number-sweep-angle parameter (beta cotangent A) sub DES of 0.6, 0.75, and 0.9, respectively. For each sweep angle, camber surfaces having design lift coefficients of 0,0.08, and 0.12 at a design Mach number of 2.6 were generated. The wind-tunnel tests were conducted at Mach numbers of 2.3, 2.6, and 2.96 with a stagnation temperature of 338.7 K (150 F) and a Reynolds number per meter of 9.843 times 10 to the 6th power. The results of the tests showed that only a moderate sweeping of the wing leading edge aft of the Mach line along with a small-to-moderate amount of camber and twist was needed to significantly improve the zero-lift (flat camber surface) wing performance and efficiency.

Mack, R. J.↗

NASA NTRS1978

On the shear pumping effect in rocket pump inducers

The momentum exchange between the fluid and the rotor via the shear stress in a rocket pump inducer is termed the shear pumping effect. This effect is investigated analytically in order to estimate the direct effect of shear stress in providing a head rise. An inducer with flat plates and one with cambered blades are considered. It is shown that the head rise coefficient and the relative velocities predicted from the theoretical analysis, based on momentum integral technique, seem to agree well with the measured data for a flat-plate inducer operated with open throttle and a cambered-blade inducer operated at a flow coefficient of 0.065. In particular, the flat-plate and the cambered-blade inducers have nearly the same performance, except for the axial velocity distribution. The former shows a tendency to separate in the hub region near the trailing edge, while the latter does not. Even far downstream, the flat-plate inducer has a larger separated zone near the hub.

Lakshminarayana, B.↗

NASA NTRS1979

Optimized aerodynamic design process for subsonic transport wing fitted with winglets

The aerodynamic design of a wind-tunnel model of a wing representative of that of a subsonic jet transport aircraft, fitted with winglets, was performed using two recently developed optimal wing-design computer programs. Both potential flow codes use a vortex lattice representation of the near-field of the aerodynamic surfaces for determination of the required mean camber surfaces for minimum induced drag, and both codes use far-field induced drag minimization procedures to obtain the required spanloads. One code uses a discrete vortex wake model for this far-field drag computation, while the second uses a 2-D advanced panel wake model. Wing camber shapes for the two codes are very similar, but the resulting winglet camber shapes differ widely. Design techniques and considerations for these two wind-tunnel models are detailed, including a description of the necessary modifications of the design geometry to format it for use by a numerically controlled machine for the actual model construction.

Kuhlman, J. M.↗

NASA NTRS1980

Development of a vortex-lift-design method and application to a slender maneuver-wing configuration

A method has been developed to optimize the mean camber surface of a cranked slender wing having leading-edge vortex flow at transonic-maneuver conditions using the suction analogy. This type of flow was assumed because it was anticipated that the slenderness of the wing would preclude attached flow at the required lift coefficient. A constraint was imposed in that the camber deflections were to be restricted by a realistic structural-box requirement. The resulting application yielded mean-camber shapes which produced effective suction levels equivalent to 77 percent of the full-planar leading-edge value at the design lift coefficient.

Lamar, J. E.↗

NASA NTRS1981

Pressure and force data for a flat wing and a warped conical wing having a shockless recompression at Mach 1.62

A conical nonlinear flow computer code was used to design a warped (cambered) wing which would produce a supercritical expansion and shockless recompression of the crossflow at a lift coefficient of 0.457, an angle of attack of 10 deg, and a Mach number of 1.62. This cambered wing and a flat wing the same thickness distribution were tested over a range of Mach numbers from 1.6 to 2.0. For both models the forward 60 percent is purely conical geometry. Results obtained with the cambered wing demonstrated the design features of a supercritical expansion and a shockless recompression, whereas results obtained with the flat wing indicated the presence of crossflow shocks. Tables of experimental pressure, force, and moment data are included, as well as selected oil flow photographs.

Miller, D. S.↗

NASA NTRS1981

Numerical optimization of circulation control airfoils

A numerical procedure for optimizing circulation control airfoils, which consists of the coupling of an optimization scheme with a viscous potential flow analysis for blowing jet, is presented. The desired airfoil is defined by a combination of three baseline shapes (cambered ellipse, and cambered ellipse with drooped and spiralled trailing edges). The coefficients of these shapes are used as design variables in the optimization process. Under the constraints of lift augmentation and lift-to-drag ratios, the optimal airfoils are found to lie between those of cambered ellipse and the drooped trailing edge, towards the latter as the angle of attack increases. Results agree qualitatively with available experimental data.

Tai, T. C.↗

NASA NTRS1981

Vibrations of twisted rotating blades

The literature dealing with vibrations of turbomachinery blades is voluminous, but the vast majority of it treats the blades as beams. In a previous paper a two-dimensional analytical procedure was developed and demonstrated on simple models of blades having camber. The procedure utilizes shallow shell theory along with the classical Ritz method for solving the vibration problem. Displacement functions are taken as algebraic polynomials. In the present paper the method is demonstrated on blade models having camber. Comparisons are first made with results in the literature for nonrotating twisted plates and various disagreements between results are pointed out. A method for depicting mode shape information is demonstrated, permitting one to examine all three components of displacement. Finally, the analytical procedure is demonstrated on rotating twisted blade modes, both without and with camber.

Leissa, A. W.↗

NASA NTRS1983

A comparison of trim drag for conventional and supercritical wings

The magnitude of the trim drag incurred by advanced supercritical wings and conventional wide-body wings at cruise conditions are investigated. Experiments were performed in a transonic pressure tunnel at a Mach number of 0.82 with a conventional wide-body wing and supercritical wing with high aspect ratio (9.80) using one of three low-tail configurations or two T-tail configurations in order to determine the effects of horizontal tail size, location, camber and static margin. Drag measurements indicate trim drag for the supercritical wing not to be significantly higher than for the conventional wing, although the minimum drag values for the supercritical wing occurred at lower static margins than for conventional wings. Both wings exhibited a reduction in trim drag with reduced cambered tail size, and greater minimum drag increments for cambered tails than for symmetrical tails. Lower trim-drag increments were also observed for the T-tail configuration than the low tails. The increase in lift-drag ratio for the supercritical wing over the conventional wing amounted to 11% for the best tail configurations.

Jacobs, P. F.↗