Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CFD simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

A Transported Livengood–Wu Integral Model for Knock Prediction in Computational Fluid Dynamics Simulation

This work describes the development of a transported Livengood–Wu (L–W) integral model for computational fluid dynamics (CFD) simulation to predict autoignition and engine knock tendency. The currently employed L–W integral model considers both single-stage and two-stage ignition processes, thus can be generally applied to different fuels such as paraffin, olefin, aromatics, and alcohol. The model implementation is first validated in simulations of homogeneous charge compression ignition (HCCI) combustion for three different fuels, showing good accuracy in prediction of autoignition timing for fuels with either single-stage or two-stage ignition characteristics. Then, the L–W integral model is coupled with G-equation model to indicate end-gas autoignition and knock tendency in CFD simulations of a direct-injection spark-ignition engine. This modeling approach is about 10 times more efficient than the ones that based on detailed chemistry calculation and pressure oscillation analysis. Two fuels with same Research Octane Number (RON) but different octane sensitivity are studied, namely, Co-Optima alkylate and Co-Optima E30. Feed-forward neural network model in conjunction with multivariable minimization technique is used to generate fuel surrogates with targets of matched RON, octane sensitivity, and ethanol content. The CFD model is validated against experimental data in terms of pressure traces and heat release rate for both fuels under a wide range of operating conditions. The knock tendency—indicated by the fuel energy contained in the autoignited region—of the two fuels at different load conditions correlates well with the experimental results and the fuel octane sensitivity, implying the current knock modeling approach can capture the octane sensitivity effect and can be applied to further investigation on composition of octane sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗

Application of OpenFOAM to Plume Impingement in Space Environments

After 30 years of continuous human presence in low-earth orbit, NASA is returning to the moon and eventually will go to Mars. Travelling beyond low earth orbit requires NASA to learn how humans can live in Deep Space environments – beyond the protection of Earth’s magnetosphere and at distances from Earth that prevent a quick return in case of trouble. To this end, NASA is constructing the Lunar Gateway, an ISS-like space station to be put in orbit around the moon to act as a home base for Lunar exploration for NASA astronauts. The Gateway Lunar outpost will be built incrementally, via modules which will arrive at separate times and dock to the existing structure. The incremental addition of Gateway modules, and the docking of visiting vehicles, is achieved via a sequence of firings from the approaching body’s onboard reaction control system (RCS) thrusters to achieve the required approach trajectory. The typical hypergolic chemical RCS thrusters work by firing hot gases to produce adverse thrust and the needed change in velocity to safely finish the docking process. The exhaust gas from the RCS thrusters form plumes that expand into the vacuum of space and can impinge onto the outer surfaces of the Lunar Gateway, causing unwanted forces and moments, heat loads, sediment deposition, and in extreme cases, even surface erosion - all mechanisms that can damage the Lunar Gateway and must be minimized. Both permanent and visiting modules will have this RCS thruster exhaust impingement problem. This research aims to establish existing OpenFOAM solvers as a methodology for improving simulation techniques of rocket exhaust plume impingement in space environments. The flow structure of a plume in a space environment is complex; a plume that originates from a hypergolic chemical RCS thruster and expands into a vacuum will experience several regimes of rarefication. This range includes the continuum flow in the rocket nozzle through the fully rarefied free molecular flow further from the nozzle. The flow physics is different at these two extremes, and as such, the simulation approach for plumes is generally divided into a traditional computational fluid dynamics (CFD) simulation in and near the nozzle which is coupled to a subsequent direct simulation Monte Carlo (DSMC) simulation. At this time, the scope of this research is developing, verifying, and validating a method using existing solvers in the OpenFOAM framework for performing coupled CFD/DSMC calculations to determine the extent of plume impingement loading on generic space structures. This presentation will detail code-to-code comparisons between the hyStrath dsmcFoam+ solver, developed using OpenFOAM and available as open-source, and NASA’s in-house DSMC Analysis Code (DAC). Comparisons to several open-source publication findings using DAC [3,4] are presented, and advantages of using an OpenFOAM based solver are also discussed. The presentation concludes with a discussion of future work, and a plan for coupling the dsmcFoam+ solver with CFD simulations of chemical rocket engines for unified coupled plume simulation.

DSMC↗

Software Framework for Advanced Power Plant Simulations

This report summarizes the work accomplished during the Phase II development effort of the Advanced Process Engineering Co-Simulator (APECS). The objective of the project is to develop the tools to efficiently combine high-fidelity computational fluid dynamics (CFD) models with process modeling software. During the course of the project, a robust integration controller was developed that can be used in any CAPE-OPEN compliant process modeling environment. The controller mediates the exchange of information between the process modeling software and the CFD software. Several approaches to reducing the time disparity between CFD simulations and process modeling have been investigated and implemented. These include enabling the CFD models to be run on a remote cluster and enabling multiple CFD models to be run simultaneously. Furthermore, computationally fast reduced-order models (ROMs) have been developed that can be 'trained' using the results from CFD simulations and then used directly within flowsheets. Unit operation models (both CFD and ROMs) can be uploaded to a model database and shared between multiple users.

99 GENERAL AND MISCELLANEOUS↗

DISCRETE ELEMENT MODELING OF BLADE–STRIKE FREQUENCY AND SURVIVAL OF FISH PASSING THROUGH HYDROKINETIC TURBINES

Evaluating the consequences from blade-strike of fish on marine hydrokinetic (MHK) turbine blades is essential for incorporating environmental objectives into the integral optimization of machine performance. For instance, experience with conventional hydroelectric turbines has shown that innovative shaping of the blade and other machine components can lead to improved designs that generate more power without increased impacts to fish and other aquatic life. In this work, we used unsteady computational fluid dynamics (CFD) simulations of turbine flow and discrete element modeling (DEM) of particle motion to estimate the frequency and severity of collisions between a horizontal axis MHK tidal energy device and drifting aquatic organisms or debris. Two metrics are determined with the method: the strike frequency and survival rate estimate. To illustrate the procedure step-by-step, an exemplary case of a simple runner model was run and compared against a probabilistic model widely used for strike frequency evaluation. The results for the exemplary case showed a strong correlation between the two approaches. In the application case of the MHK turbine flow, turbulent flow was modeled using detached eddy simulation (DES) in conjunction with a full moving rotor at full scale. The CFD simulated power and thrust were satisfactorily comparable to experimental results conducted in a water tunnel on a reduced scaled (1:8.7) version of the turbine design. A cloud of DEM particles was injected into the domain to simulate fish or debris that were entrained into the turbine flow. The strike frequency was the ratio of the count of colliding particles to the crossing sample size. The fish length and approaching velocity were test conditions in the simulations of the MHK turbine. Comparisons showed that DEM-based frequencies tend to be greater than previous results from Lagrangian particles and probabilistic models, mostly because the DEM scheme accounts for both the geometric aspects of the passage event ---which the probabilistic method does--- as well as the fluid-particle interactions ---which the Lagrangian particle method does. The DEM-based survival rates were comparable to laboratory results for small fish but not for mid-size fish because of the considerably different turbine diameters. The modeling framework can be used for applications that aim at evaluating the biological performance of MHK turbine units during the design phase and to provide information to regulatory agencies needed for the environmental permitting process.

blade strike↗

Verification and Validation of COMSOL for Heat Transfer in Thin Rectangular Channels Using NACA Test Results

Currently efforts are underway at Oak Ridge National Lab (ORNL) to convert the High Flux Isotope Reactor (HFIR) from high enriched uranium to low enriched uranium fuel. In order to provide confidence to the thermal hydraulics calculations, computational fluid dynamics (CFD) simulations – simulated using COMOSOL – have been employed to calculate the pressure drop and heat transfer in the coolant. While CFD simulations provide well resolved results, turbulence models include a large amount of assumptions and must be validated for use in any safety-based analysis. In HFIR, long thin involute fuel plates are separated by coolant channels of equal size. The coolant channels are best described as thin rectangular channels. Unfortunately, there are few studies verifying and validating CFD for use in thin rectangular channels. This study seeks to bridge that gap by verifying, validating, and comparing various CFD models used in thin channels. To verify and validate CFD for use in thin channels, a series of simple analytic test cases are employed, and MMS is used to further verify the COMSOL tool and mesh geometry. For the validation, a series of tests conducted at NASA were simulated in COMSOL. The results of this study are three-fold. First, it verifies the ability of COMSOL to model heat transfer in thin channels. Second, it addresses the various aspects of CFD modeling that are of greatest concern for heat transfer simulations in the geometry. Third, and finally, it discusses the ability of various CFD models used in COMSOL to accurately predict heat transfer in narrow rectangular channels.

Howard, Trevor↗

Advancing the State-of-the-Practice for Liquid Rocket Engine Injector Design

Current shortcomings in both the overall injector design process and its underlying combustion stability assessment methodology are rooted in the use of empirically based or low fidelity representations of complex physical phenomena and geometry details that have first order effects on performance, thermal environments and combustion stability. The result is a design and analysis capability that is often inadequate to reliably arrive at a suitable injector design in an efficient manner. Specifically, combustion instability has been particularly difficult to predict and mitigate. Large hydrocarbon-fueled booster engines have been especially problematic in this regard. Where combustion instability has been a problem, costly and time-consuming redesign efforts have often been an unfortunate consequence. This paper presents an overview of a recently completed effort at NASA Marshall Space Flight Center to advance the state-of-the-practice for liquid rocket engine injector design. Multiple perturbations of a gas-centered swirl coaxial (GCSC) element that burned gaseous oxygen and RP-1 were designed, assessed for combustion stability, and tested. Three designs, one stable, one marginally unstable and one unstable, were used to demonstrate both an enhanced overall injector design process and an improved combustion stability assessment process. High-fidelity results from state-of-the-art computational fluid dynamics CFD simulations were used to substantially augment and improve the injector design methodology. The CFD results were used to inform and guide the overall injector design process. They were also used to upgrade selected empirical or low-dimensional quantities in the ROCket Combustor Interactive Design (ROCCID) stability assessment tool. Hot fire single element injector testing was used to verify both the overall injector designs and the stability assessments. Testing was conducted at the Air Force Research Laboratory and at Purdue University. Companion papers provide details of the overall injector design process, full- and sub-scale testing, ROCCID-based stability assessments and the CFD simulations.

Tucker, P. K.↗

Pressure Drop in Seven-Pin Wire-Wrapped Rod Bundle for the Sodium Cartridge Loop in Versatile Test Reactor

This work studies the hydrodynamics of the seven pin wire-wrapped rod bundle in the sodium cartridge loop for the Versatile Test Reactor (VTR) through scaled water experiments and computational fluid dynamics (CFD) simulations. Here, the scaling analysis is first performed to demonstrate the hydrodynamic similarity between water and sodium flows at the same Reynolds number Re. A separate-effects test facility is designed and constructed based on the scaling analysis. Detailed experimental data on the pressure drop covering a wide range of Re values (1165 to 27 689) are obtained, which are used to evaluate existing correlations for friction factor and to benchmark CFD simulations. The experimentally determined friction factors f Exp agree well with the Upgraded Cheng and Todreas Detailed Correlation and Pacio-Chen-Todreas Detailed Model within ±7% but are significantly underpredicted by Rehme's correlation by 25%. Various CFD near-wall treatment methods are tested using ANSYS Fluent and evaluated by experimental data. It is found that when the recommended wall y + values are met, most of the near-wall treatment methods can give accurate friction factor predictions. The resolved near-wall method (y + ~ 1) with the Shear Stress Transport k - ω turbulence model and the scalable wall functions (y + > 12) with the realizable k - ε turbulence model can predict f Exp within ±5% The standard wall functions (y + > 30) and nonequilibrium wall functions (y + > 30) with the realizable k - ε model can predict f Exp within ±10%.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization of Workload Distribution of Data Centers Based on a Self-Learning In Situ Adaptive Tabulation Model

Data center cooling typically involves non-uniform airflow and temperature distributions, which are affected by the IT workload distribution. It is helpful to simulate the airflow and temperature to optimize the workload distribution. Traditional computational fluid dynamics (CFD) simulation is usually time-consuming while conventional reduced order models (ROMs), though computationally fast, may generate inaccurate results even after being fully trained. In Situ Adaptive Tabulation (ISAT), contracting to conventional ROM, can make prediction with error lower than a user-specified tolerance. To demonstrate using of ISAT for optimal workload distribution in data center, this paper presents a preliminary study of an ISAT-based genetic algorithm optimization platform. The ISAT is trained offline by using the results from CFD simulations using a hypothetical simple data center. The optimal workload distribution determined by the platform leads to approximately 6.8% of energy savings when compared to the benchmark with a uniform workload distribution. We note that the time cost for the entire optimization process, including the training of ISAT is about 4 hours, which is acceptable in the design phase.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Machine learning based prediction of airflow maldistribution in air-to-refrigerant heat exchangers

Flow maldistribution is a common challenge in heat exchanger (HX) design and particularly important for air-to-refrigerant geometries where capacity losses can approach 65%. This has a major impact on central air conditioning systems, as compact duct design motivates the use of A-type HXs which are known to be affected by airflow maldistribution. Because velocity profiles are difficult to predict, components are often oversized leading to increased material cost, system footprint, and refrigerant charge. Several studies detail airflow maldistribution for individual HXs and packages, but findings cannot always be extrapolated to new designs. In this work, a machine learning (ML) based flow profile prediction framework is developed and applied to two common package configurations: (i) A-type and (ii) U-type HXs, across a broad range of HX geometries and flow rates. Porous media CFD simulations are validated against independent data for both package types as well as comprehensive in house measurements for a finless geometry with shape optimized non-round tubes, which validates the framework for new heat transfer surfaces. The ML models are trained on the porous media CFD simulations, predicting volumetric flow rate (VFR) within 1.1% and 1.9% with maximum relative L 2 norm errors of 0.48 and 0.65, respectively, while also delivering 10 5 speed up factor compared to full porous media CFD. HX level simulations show an up to 9% reduction in heat transfer from flow maldistribution, with greater losses occurring at smaller half apex angles. This framework enables rapid and highly accurate prediction of airflow maldistribution induced capacity degradation.

42 ENGINEERING↗

Computational Fluid Dynamic Analysis for the Proposed VHTR Lower Plenum Standard Problem

One of the reference designs for the Next Generation Nuclear Plant (NGNP) is a prismatic reactor configuration. A major concern in the operation of this design is the nature of the flow of hot gas as it exits the core into the lower plenum and then out the vessel exit duct. The two primary areas of concern are the impingement of hot jets onto the walls of the lower plenum and the degree of thermal mixing of the helium coolant as it flows out of the reactor vessel. Computational fluid dynamic (CFD) simulations have been proposed by general consensus to estimate the desired local fluid dynamic and temperature information. Successful CFD simulations require careful planning and extensive calculations to help ensure that they accurately represent the flow physics. An important aspect of the application of CFD is to validate the results against detailed validation data, for scaled problems that involve similar physics. A section of the lower plenum of the reference prismatic NGNP was employed to create a scaled model to use to obtain experimental data for use as validation data to compare with a CFD analysis. Extensive flow data were obtained from the scaled model while installed in the INL’s Matched Index of Refraction (MIR) test facility.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Modifications of Carbonate Fracture Hydrodynamic Properties by CO 2 -Acidified Brine Flow

Acidic reactive flow in fractures is relevant in subsurface activities such as CO{sub 2} geological storage and hydraulic fracturing. Understanding reaction-induced changes in fracture hydrodynamic properties is essential for predicting subsurface flows such as leakage, injectability, and fluid production. In this study, x-ray computed tomography scans of a fractured carbonate caprock were used to create three dimensional reconstructions of the fracture before and after reaction with CO{sub 2}-acidified brine (Ellis et al., 2011, Greenhouse Gases: Sci. Technol., 1:248-260). As expected, mechanical apertures were found to increase substantially, doubling and even tripling in some places. However, the surface geometry evolved in complex ways including ‘comb-tooth’ structures created from preferential dissolution of calcite in transverse sedimentary bands, and the creation of degraded zones, i.e. porous calcite-depleted areas on reacted fracture surfaces. These geometric alterations resulted in increased fracture roughness, as measured by surface Z{sub 2} parameters and fractal dimensions D{sub f}. Computational fluid dynamics (CFD) simulations were conducted to quantify the changes in hydraulic aperture, fracture transmissivity and permeability. The results show that the effective hydraulic apertures are smaller than the mechanical apertures, and the changes in hydraulic apertures are nonlinear. Overestimation of flow rate by a factor of two or more would be introduced if fracture hydrodynamic properties were based on mechanical apertures, or if hydraulic aperture is assumed to change proportionally with mechanical aperture. The differences can be attributed, in part, to the increase in roughness after reaction, and is likely affected by contiguous transverse sedimentary features. Hydraulic apertures estimated by the 1D statistical model and 2D local cubic law (LCL) model are consistently larger than those calculated from the CFD simulations. In addition, a novel ternary segmentation method was devised to handle the degraded zones, allowing for a bounding analysis of the effects on hydraulic properties. We found that the degraded zones account for less than 15% of the fracture volume, but cover 70% to 80% of the fracture surface. When the degraded zones are treated as part of the fracture, the fracture transmissivities are two to four times larger because the fracture surfaces after reaction are not as rough as they would be if one considers the degraded zone as part of the rock. Therefore, while degraded zones created during geochemical reactions may not significantly increase mechanical aperture, this type of feature cannot be ignored and should be treated with prudence when predicting fracture hydrodynamic properties.

roughness↗

A PIC Bootstrapping Strategy for Exascale CFD-DEM Simulation

The exascale computing era comes with the release of MFIX-Exa, a new code for studying gas-particle fluidization using CFD-DEM and PIC models on massively parallel, heterogeneous high-performance computing architectures. However, as compute resources continue to grow in scale and complexity, so too does the impetus to use them efficiently. Here, we propose a novel bootstrapping method to minimize neglected simulation time and cast the approach more broadly among a growing field of multi-fidelity methods.

Porcu, Roberto↗

Numerical Investigation of Desulfurization Kinetics in Gas-Stirred Ladles by a Quick Modeling Analysis Approach

A quick modeling analysis approach for predicting the slag-steel reaction and desulfurization kinetics in argon gas-stirred ladles has been developed in this study. The model consists of two uncoupled components: (i) a computational fluid dynamics (CFD) model for predicting the fluid flow and the characteristics of slag-steel interface, and (ii) a multicomponent reaction kinetics model for calculating the desulfurization evolution. The steel-slag interfacial area and mass transfer coefficients predicted by the CFD simulation are used as the processing data for the reaction model. Since the desulfurization predictions are uncoupled from the CFD simulation, the computational time of this uncoupled predictive approach is decreased by at least 100 times for each case study when compared with the CFD-reaction kinetics fully coupled model. The uncoupled modeling approach was validated by comparing the evolution of steel and slag compositions with the experimentally measured data during ladle metallurgical furnace (LMF) processing at Nucor Steel Tuscaloosa, Inc. Then, the validated approach was applied to investigate the effects of the initial steel and slag compositions, as well as different types of additions during the refining process on the desulfurization efficiency. The results revealed that the sulfur distribution ratio and the desulfurization reaction can be promoted by making Al and CaO additions during the refining process. It was also shown that by increasing the initial Al content in liquid steel, both Al oxidation and desulfurization rates rapidly increase. In addition, it was found that the variation of the initial Si content in steel has no significant influence on the desulfurization rate. Lastly, if the initial CaO content in slag is increased or the initial Al{sub 2}O{sub 3} content is decreased in the fluid-slag compositional range, the desulfurization rate can be improved significantly during the LMF process.

36 MATERIALS SCIENCE↗

Chemical Kinetics of the TPS and Base Bleeding During Flight Test

The present research deals with thermal degradation of polyurethane foam (PUF) during flight test. Model of thermal decomposition was developed that accounts for polyurethane kinetics parameters extracted from thermogravimetric analyses and radial heat losses to the surrounding environment. The model predicts mass loss of foam, the temperature and kinetic of release of the exhaust gases and char as function of heat and radiation loads. When PUF is heated, urethane bond break into polyol and isocyanate. In the first stage, isocyanate pyrolyses and oxidizes. As a result, the thermo-char and oil droplets (yellow smoke) are released. In the second decomposition stage, pyrolysis and oxidization of liquid polyol occur. Next, the kinetics of chemical compound release and the information about the reactions occurring in the base area are coupled to the CFD simulations of the base flow in a single first stage motor vertically stacked vehicle configuration. The CFD simulations are performed to estimate the contribution of the hot out-gassing, chemical reactions, and char oxidation to the temperature rise of the base flow. The results of simulations are compared with the flight test data.

Osipov, Viatcheslav↗

Surface Flow Visualization of the High-Lift Common Research Model

A 10% scale version of the High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The CRM-HL experiment included various configurations such as conventional and simple-hinged flaps, with and without engine nacelle/pylon, with and without nacelle chine, different Active Flow Control (AFC) methods (sweeping jets, alternating pulsed jets, and preconditioned boundary layer blowing), and their various parameters. This particular study is focused on the surface flow visualization of the conventional CRM-HL model at landing configuration. The conventional CRM-HL model with the single-slotted Fowler flap system serves as a baseline for the AFC-enabled simplified high-lift configuration as well as a high-lift technology development platform due to its publicly open geometry. Surface flow visualizations were performed using fluorescent minitufts, which were found to be nonintrusive to the aerodynamic performance. Tuft flow visualizations are supplemented with the relevant pressure and force measurements in order to understand the flow characteristics developed on the conventional CRM- HL model. In addition, three dimensional, unsteady, compressible Computational Fluid Dynamic (CFD) simulations were performed for selective cases. The surface streamlines and transverse velocity fluctuations obtained by the CFD simulations are qualitatively compared to the tuft direction and tuft unsteadiness, respectively. Force measurements of the CRM-HL model show performance degradation at higher angles of attack. Surface flow visualizations revealed the performance loss due to the nacelle/pylon wake that grows with angle of attack and eventually promotes flow separation over the inboard wing. This performance loss was successfully recovered by placing a chine on the engine nacelle.

Koklu, Mehti↗

CFD-Based Frequency Domain Method for Dynamic Stability Derivative Estimation with Application to Transonic Truss-Braced Wing

This paper presents a dynamic stability estimation technique obtained from high-fidelity CFD simulations of the Mach 0.8 Transonic Truss-Braced Wing (TTBW). A series of unsteady RANS CFD simulations in FUN3D is performed on the TTBW in pitch and plunge oscillations at various reduced frequencies. The time-domain data are transformed into the frequency-domain data by Fourier series. Transfer functions of the dynamic stability derivatives are then estimated by a frequency-domain regression. The dynamic stability derivatives with respect to the angle of attack are determined by the regression of the unsteady aerodynamic coefficients for the plunge motion. The dynamic stability derivatives with respect to the pitch rate are deter-mined by the regression of the differential unsteady aerodynamic coefficients for the pitch motion upon the removal of the angle of attack contribution by the plunge motion. The steady-state stability derivatives are then compared to the results obtained from a stability analysis code VSPAERO as well as steady-state FUN3D simulations. The comparison of the steady-state stability derivatives shows excellent agreement.

Dynamic Stability Derivatives↗

A Computational Study of the Abrupt Wing Stall (AWS) Characteristics for Various Fighter Jets: F/A-18E and F-16C - Part 1

Steady state Computational Fluid Dynamic (CFD) simulations are used to gain an understanding of the physics behind the Abrupt Wing Stall (AWS) phenomenon and to arrive at static Figures of Merit (FOMs). Navier-Stokes simulations are conducted using the NASA Langley developed TetrUSS simulation suite which is based on tetrahedral, unstructured grids. The physics of the AWS phenomenon is understood by comparing CFD simulation results on two aircraft; a pre-production F/A-18E configuration which exhibits AWS phenomenon under certain geometric and flow conditions, and an F-16C aircraft configuration that does not. The CFD code is first validated against two sets of experimental data to build confidence in its use for the problem of AWS. An attempt is then made to understand the possible causes of AWS by analyzing and comparing the detailed flow fields between the two configurations under a variety of flow conditions. Based on this approach, a number of static Figures of Merit are developed to predict the potential existence of AWS. The FOMs include the break in the lift and wing root bending moment versus angle-of-attack (AoA) curves and the rate of change of sectional lift with respect to AoA. A companion paper, in Part II, describes a similar CFD study on two other aircraft, the AV-8B Harrier and F/A-18C. Results from both these studies, as well as other CFD studies conducted as part of the AWS program are used to recommend a CFD procedure for predicting the existence of AWS in future aerospace designs.

Parikh, Paresh↗