Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary Layer Profiles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Experimental Investigation of the Flow Field in a Transonic, Axial Flow Compressor with Respect to the Development of Blockage and Loss

A detailed experimental investigation to understand and quantify the development of loss and blockage in the flow field of a transonic, axial flow compressor rotor has been undertaken. Detailed laser anemometer measurements were acquired upstream, within, and downstream of a transonic, axial compressor rotor operating at design and off-design conditions. The rotor was operated at 100%, 85%, 80%, and 60% of design speed which provided inlet relative Mach numbers at the blade tip of 1.48, 1.26, 1.18, and 0.89 respectively. At design speed the blockage is evaluated ahead of the rotor passage shock, downstream of the rotor passage shock, and near the trailing edge of the blade row. The blockage is evaluated in the core flow area as well as in the casing endwall region. Similarly at pm speed conditions for the cases of (1) where the rotor passage shock is much weaker than that at design speed and (2) where there is no rotor passage shock, the blockage and loss are evaluated and compared to the results at design speed. Specifically, the impact of the rotor passage shock on the blockage and loss development, pertaining to both the shock/boundary layer interactions and the shock/tip clearance flow interactions, is discussed. In addition, the blockage evaluated from the experimental data is compared to (1) an existing correlation of blockage development which was based on computational results, and (2) computational results on a limited basis. The results indicate that for this rotor the blockage in the endwall region is 2-3 times that of the core flow region and the blockage in the core flow region more than doubles when the shock strength is sufficient to separate the suction surface boundary layer. The distribution of losses in the care flow region indicate that the total loss is primarily comprised of the shock loss when the shock strength is not sufficient to separate the suction surface boundary layer. However, when the shock strength is sufficient to separate the suction surface boundary layer, the profile loss is comparable to the shock loss and can exceed the shock loss.

Suder, Kenneth L.↗
NASA NTRS1995

Computations of Axisymmetric Flows in Hypersonic Shock Tubes

A time-accurate two-dimensional fluid code is used to compute test times in shock tubes operated at supersonic speeds. Unlike previous studies, this investigation resolves the finer temporal details of the shock-tube flow by making use of modern supercomputers and state-of-the-art computational fluid dynamic solution techniques. The code, besides solving the time-dependent fluid equations, also accounts for the finite rate chemistry in the hypersonic environment. The flowfield solutions are used to estimate relevant shock-tube parameters for laminar flow, such as test times, and to predict density and velocity profiles. Boundary-layer parameters such as bar-delta(sub u), bar-delta(sup *), and bar-tau(sub w), and test time parameters such as bar-tau and particle time of flight t(sub f), are computed and compared with those evaluated by using Mirels' correlations. This article then discusses in detail the effects of flow nonuniformities on particle time-of-flight behind the normal shock and, consequently, on the interpretation of shock-tube data. This article concludes that for accurate interpretation of shock-tube data, a detailed analysis of flowfield parameters, using a computer code such as used in this study, must be performed.

Sharma, Surendra P.↗
NASA NTRS1959

Skin-Friction Measurements in Incompressible Flow

Experiments have been conducted to measure the local surface-shear stress and the average skin-friction coefficient in Incompressible flow for a turbulent boundary layer on a smooth flat plate having zero pressure gradient. Data were obtained for a range of Reynolds numbers from 1 million to 45 million. The local surface-shear stress was measured by a floating-element skin-friction balance and also by a calibrated total head tube located on the surface of the test wall. The average skin-friction coefficient was obtained from boundary-layer velocity profiles.

Smith, Donald W.↗
NASA NTRS2009

Numerical Solutions for the CAWAPI Configuration on Structured Grids at NASA LaRC, United States

In this chapter numerical simulations of the flow around F-16XL are performed as a contribution to the Cranked Arrow Wing Aerodynamic Project International (CAWAPI) using the PAB3D CFD code. Two turbulence models are used in the calculations: a standard k-epsilon model, and the Shih-Zhu-Lumley (SZL) algebraic stress model. Seven flight conditions are simulated for the flow around the F-16XL where the free stream Mach number varies from 0.242 to 0.97. The range of angles of attack varies from 0 deg to 20 deg. Computational results, surface static pressure, boundary layer velocity profiles, and skin friction are presented and compared with flight data. Numerical results are generally in good agreement with flight data, considering that only one grid resolution is utilized for the different flight conditions simulated in this study. The Algebraic Stress Model (ASM) results are closer to the flight data than the k-epsilon model results. The ASM predicted a stronger primary vortex, however, the origin of the vortex and footprint is approximately the same as in the k-epsilon predictions.

Elmiligui, Alaa A.↗
NASA NTRS2010

Micro-Ramps for External Compression Low-Boom Inlets

The application of vortex generators for flow control in an external compression, axisymmetric, low-boom concept inlet was investigated using RANS simulations with three-dimensional (3-D), structured, chimera (overset) grids and the WIND-US code. The low-boom inlet design is based on previous scale model 1- by 1-ft wind tunnel tests and features a zero-angle cowl and relaxed isentropic compression centerbody spike, resulting in defocused oblique shocks and a weak terminating normal shock. Validation of the methodology was first performed for micro-ramps in supersonic flow on a flat plate with and without oblique shocks. For the inlet configuration, simulations with several types of vortex generators were conducted for positions both upstream and downstream of the terminating normal shock. The performance parameters included incompressible axisymmetric shape factor, separation area, inlet pressure recovery, and massflow ratio. The design of experiments (DOE) methodology was used to select device size and location, analyze the resulting data, and determine the optimal choice of device geometry. The optimum upstream configuration was found to substantially reduce the post-shock separation area but did not significantly impact recovery at the aerodynamic interface plane (AIP). Downstream device placement allowed for fuller boundary layer velocity profiles and reduced distortion. This resulted in an improved pressure recovery and massflow ratio at the AIP compared to the baseline solid-wall configuration.

Rybalko, Michael↗
NASA NTRSDate not supplied

Atmospheric Boundary-Layer and Flutter Computations Using CFD Model of the Transonic Dynamics Tunnel

This paper presents two Computational Fluid Dynamics (CFD) models of the flow in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). The TDT is a continuous-flow, closed circuit wind tunnel with a 16- by 16-foot slotted test section with cropped corners. The tunnel was originally built as the 19-ft Pressure Tunnel in 1938, but it was converted to the current transonic tunnel in the 1950s, with capabilities to use either air or heavy gas as the test medium. The first computational model describes the generation of an atmospheric-boundary-layer (ABL) profile inside the tunnel. An ABL, which includes both a wind profile and turbulence content, is one of the aerodynamic characteristics affecting the occurrence of wind-induced oscillations for a launch vehicle sitting on a pad. The challenging part of this analysis was modeling the turbulent flow inside the tunnel. This is due to the special ABL-generating hardware that was installed at the entrance of the TDT test section in order to change the downstream velocity profile and to introduce velocity fluctuations into the flow. The second CFD model builds on the computational aeroelastic results that were generated in support of the second Aeroelastic Prediction Workshop (AePW) for the NASA Benchmark Supercritical Wing (BSCW) configuration. During the AePW, the wing-only configuration (classical free-air model) was analyzed. In the current study, the flutter computations were conducted on the configuration as it was mounted in the TDT during the experiment. This includes the wing attached to the splitter plate that was attached to the wind-tunnel walls. The preliminary results show that the wind-tunnel walls marginally affect flutter prediction.

Pawel Chwalowski↗
NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations for High-Lift Configurations using FUN3D

Wall-modeled large-eddy simulation (WMLES) capability has recently been implemented into FUN3D, an unstructured, node-centered, finite-volume solver developed at the NASA Langley Research Center. In this paper, WMLES is assessed for two configurations that are representative for high-lift applications. The first configuration is a nominal two-dimensional multielement airfoil that has been extensively studied in the literature. WMLES solutions are computed for four angles of attack and compared with previously reported solutions. Good agreement of integrated forces, surface pressures, and boundary-layer velocity profiles is shown with available experimental data especially at lower angles of attack. WMLES solutions are also computed for the NASA High-Lift Common Research Model over a large range of angles of attack. Forces, pitching moments, and pressure distributions are favorably compared with the experimental data up to the maximum lift, including the angle of attack where the maximum lift is obtained experimentally. Eddy visualization techniques of q-criterion and density-gradient magnitude illustrate the resolved content.

High-Lift flows↗
NASA NTRS1976

Artificial thickening of transonic boundary layers

A wind-tunnel experiment was performed to examine the effect of turbulence enhancers on the growth of a flat-plate turbulent boundary layer. The free-stream Mach number was varied from 0.6 to 0.9 with unit Reynolds numbers of 6.56 million/m and 13.12 million/m. Several configurations of high-drag objects were mounted near the leading edge of a long flat plate to introduce momentum losses. Measurements of both mean and time-variable flow parameters were made at downstream locations to quantify the influence of the turbulence enhancers. A configuration consisting of two rows of alternately spaced, vertical, 0.317-cm-diameter cylinders of 16 and 12 diameters length produced 1/9to 1/7-power velocity profiles. Unsteady total-temperature and static-pressure profiles were found to be similar to natural turbulent boundary-layer profiles. The techniques presented can be useful whenever thick turbulent boundary layers are required, but the natural growth of the layer is limited by the test facility.

Otten, L. J.↗
NASA NTRS1991

Experimental study of boundary layer transition with elevated freestream turbulence on a heated flat plate

A detailed investigation to document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were acquired in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities (TI) from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for R(sub theta) is less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length. The measured laminar value of Reynolds analogy factor was as much as 53 percent higher than the Pr(sup -2/3). A small dependence of turbulent results on TI was observed. Conditional sampling performed in the transitional boundary layer indicated the existence of a near-wall drop in intermittency, pronounced at certain low intermittencies, which is consistent with the cross-sectional shape of turbulent spots observed by others. Non-turbulent intervals were observed to possess large magnitudes of near-wall unsteadiness and turbulent intervals had peak values as much as 50 percent higher than were measured at fully turbulent stations. Non-turbulent and turbulent profiles in transitional boundary layers cannot be simply treated as Blasius and fully turbulent profiles, respectively. The boundary layer spectra indicate predicted selective amplification of T-S waves for TI is approximately 0.4 percent. However, for TI is approximately 0.8 and 1.1 percent, T-S waves are localized very near the wall and do not play a dominant role in transition process.

Sohn, Ki-Hyeon↗
NASA NTRS2000

BOREAS AFM-03-NCAR Electra 1994 Aircraft Sounding Data

The Boreal Ecosystem-Atmosphere Study (BOREAS) Airborne Fluxes and Meteorology (AFM)-3 team used the National Center for Atmospheric Research's (NCAR) Electra aircraft to make sounding measurements to study the planetary boundary layer using in situ and remote-sensing measurements. Measurements were made of wind speed and direction, air pressure and temperature, potential temperature, dewpoint, mixing ratio of H, O, CO, concentration, and ozone concentration. Twenty-five research missions were flown over the Northern Study Area (NSA), Southern Study Area (SSA), and the transect during BOREAS Intensive Field Campaigns (IFCs) 1, 2, and 3 during 1994. All missions had from four to ten soundings through the top of the planetary boundary layer. This sounding data set contains all of the in situ vertical profiles through the boundary layer top that were made (with the exception of 'porpoise' maneuvers). Data were recorded in one-second time intervals. These data are stored in tabular ASCII files. The NCAR Electra 1994 aircraft sounding data are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

Lenschow, Donald H.↗
NASA NTRS2006

Improved Atmospheric Boundary Layer Observations of Tropical Cyclones with the Imaging Wind and Rain Airborne Profiler

The Imaging Wind and Rain Arborne Profilers (IWRAP) is a dual-frequency, conically-scanning Doppler radar that measures high-resolution, dual-polarized, multi-beam C- and Ku-band reflectivity and Doppler velocity profiles of the atmospheric boundary layer (ABL) within the inner core of hurricanes.From the datasets acquired during the 2002 through 20O5 hurricane seasons as part of the ONR Coupled Boundary Layer Air-Sea Transfer (CBLAST) program and the NOAA/NESDIS Ocean Winds and Rain experiments, very high resolution radar observations of hurricanes have been acquired and made available to the CBLAST community. Of particular interest am the ABL wind fields and 3-D structures found within the inner core of hurricanes. As a result of these analysis, a limitation in the ability to retrieve the ABL wind field at very low altitudes was identified. This paper shows how this limitation has been removed and presents initial results demonstrating its new capabilities to derive the ABL wind field within the inner are of hurricanes to much lower altitudes than the ones the original system was capable of.

wind field↗
NASA NTRS2011

Hypersonic Boundary Layer Transition Measurements Using NO2 approaches NO Photo-dissociation Tagging Velocimetry

Measurements of instantaneous and mean streamwise velocity profiles in a hypersonic laminar boundary layer as well as a boundary layer undergoing laminar-to-turbulent transition were obtained over a 10-degree half-angle wedge model. A molecular tagging velocimetry technique consisting of a NO2 approaches?NO photo-dissociation reaction and two subsequent excitations of NO was used. The measurement of the transitional boundary layer velocity profiles was made downstream of a 1-mm tall, 4-mm diameter cylindrical trip along several lines lying within a streamwise measurement plane normal to the model surface and offset 6-mm from the model centerline. For laminar and transitional boundary layer measurements, the magnitudes of streamwise velocity fluctuations are compared. In the transitional boundary layer the fluctuations were, in general, 2-4 times larger than those in the laminar boundary layer. Of particular interest were fluctuations corresponding to a height of approximately 50% of the laminar boundary layer thickness having a magnitude of nearly 30% of the mean measured velocity. For comparison, the measured fluctuations in the laminar boundary layer were approximately 5% of the mean measured velocity at the same location. For the highest 10% signal-to-noise ratio data, average single-shot uncertainties using a 1 ?Es and 50 ?Es interframe delay were ~115 m/s and ~3 m/s, respectively. By averaging single-shot measurements of the transitional boundary layer, uncertainties in mean velocity as low as 39 m/s were obtained in the wind tunnel. The wall-normal and streamwise spatial resolutions were 0.14-mm (2 pixel) and 0.82-mm (~11 pixels), respectively. These measurements were performed in the 31-inch Mach 10 Air Wind Tunnel at the NASA Langley Research Center.

Bathel, Brett F.↗
NASA NTRS1988

Glancing shock wave-turbulent boundary layer interaction with boundary layer suction

Tests conducted to ascertain the stagnation pressure and flow angularity profiles of a turbulent boundary layer subjected to boundary layer suction (BLS) as it crosses a glancing sidewall shock wave have determined that the boundary layer does not separate upon crossing the shock wave. Without BLS, the upstream influence of the shock wave-induced wall static pressure rise was extensive, of the order of four bloundary layer thicknesses; for the same case, with suction, the extent of upstream influence was 50 percent lower. In addition, flow angularities at the wall were found to be smaller with suction than without it.

Barnhart, P. J.↗
NASA NTRS1991

User's manual for the Langley boundary layer noise propagation program (MRS-BLP)

A computer program, McAninch-Rawls-Spence Boundary Layer Propagation (MRS-BLP), is described. This program models the refractive and scattering effects on acoustic pressure waves propagating through a boundary layer encompassing an aircraft's fuselage. The noise source is assumed known and generated by a propeller. The fuselage is represented by an infinitely long cylinder embedded in a longitudinal flow. By matching a numerical solution inside the boundary layer with an analytical solution outside the boundary layer, the program calculates the acoustic pressure at the surface of the cylinder given the incident field at the top of the boundary layer. The boundary layer flow velocity and sound speed profiles, as well as the boundary layer thickness may be specified by the user. A detailed description of the input parameters and how to execute the program is given. Example executions of MRS-BLP showing results are also included.

Spence, Peter L.↗
NASA NTRS1989

On strongly nonlinear vortex/wave interactions in boundary-layer transition

The interactions between longitudinal vortices and accompanying waves considered are strongly nonlinear, in the sense that the mean-flow profile throughout the boundary layer is completely altered from its original undisturbed state. Nonlinear interactions between vortex flow and Tollmien-Schlichting waves are addressed first, and some analytical and computational properties are described. These include the possibility in the spatial-development case of a finite-distance break-up, inducing a singularity in the displacement thickness. Second, vortex/Rayleigh wave nonlinear interactions are considered for the compressible boundary-layer, along with certain special cases of interest and some possible solution properties. Both types, vortex/Tollmien-Schlichting and vortex/Rayleigh, are short-scale/long-scale interactions and they have potential applications to many flows at high Reynolds numbers. The strongly nonlinear nature is believed to make them very relevant to fully fledged transition to turbulence.

Hall, Philip↗
NASA NTRS2013

Trip-Induced Transition Measurements in a Hypersonic Boundary Layer Using Molecular Tagging Velocimetry

Measurements of mean streamwise velocity, fluctuating streamwise velocity, and instantaneous streamwise velocity profiles in a hypersonic boundary layer were obtained over a 10-degree half-angle wedge model. A laser-induced fluorescence-based molecular tagging velocimetry technique was used to make the measurements. The nominal edge Mach number was 4.2. Velocity profiles were measured both in an untripped boundary layer and in the wake of a 4-mm diameter cylindrical tripping element centered 75.4 mm downstream of the sharp leading edge. Three different trip heights were investigated: k = 0.53 mm, k = 1.0 mm and k = 2.0 mm. The laminar boundary layer thickness at the position of the measurements was approximately 1 mm, though the exact thickness was dependent on Reynolds number and wall temperature. All of the measurements were made starting from a streamwise location approximately 18 mm downstream of the tripping element. This measurement region continued approximately 30 mm in the streamwise direction. Additionally, measurements were made at several spanwise locations. An analysis of flow features show how the magnitude, spatial location, and spatial growth of streamwise velocity instabilities are affected by parameters such as the ratio of trip height to boundary layer thickness and roughness Reynolds number. The fluctuating component of streamwise velocity measured along the centerline of the model increased from approximately 75 m/s with no trip to +/-225 m/s with a 0.53-mm trip, and to +/-240 m/s with a 1-mm trip, while holding the freestream Reynolds number constant. These measurements were performed in the 31-inch Mach 10 Air Tunnel at the NASA Langley Research Center.

Bathel, Brett F.↗