Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Arrays”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Soft x-ray spectrum unfold of K-edge filtered x-ray diode arrays using cubic splines

Cubic spline interpolation is able to recover temporally and spectrally resolved soft x-ray flux from an array of K-edge filtered x-ray diodes without the need for a priori assumptions about the spectrum or the geometry of the emitting volume. The mathematics of the cubic spline interpolation is discussed in detail. The analytic nature of the cubic spline solution allows for analytical error propagation, and the method of calculating the error for radiation temperature, spectral power, and confidence intervals of the unfolded spectrally resolved flux is explained. An unfold of a blackbody model demonstrates the accuracy of the cubic spline unfold. Tests of cubic spline performance using spectrally convolved detailed atomic model simulation results have been performed to measure the method's ability to conserve spectral power to within a factor of 2 or better in line-dominated regimes. The unfold is also demonstrated to work when information from the x-ray diode array is limited due to high signal-to-noise ratios or lack of signal due to over-attenuation or over-filtration of the x-ray diode signal. Here, the robustness of the unfold with respect to background subtraction and raw signal processing, signal alignment between diode traces, limited signal information, and initial conditions is discussed. Results from an example analysis of a halfraum drive are presented to demonstrate the capabilities of the unfold in comparison with previously established methods.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Development of a large array of Silicon Drift Detectors for high-rate synchrotron fluorescence spectroscopy

An array of small-area Silicon Drift Detectors (SDD), named Hera, has been developed at Brookhaven National Laboratory (BNL) in the past few years. Its primary application is high-rate spectroscopy at synchrotrons. Each SDD pixel is a 1 mm × 1 mm square to match the footprint of the original diode-based pixel detector called Maia, which was developed for the same application. The replacement of the diode with an SDD allows for better energy resolution at short shaping times and an increased stability of the detector. 32, 96, and 384-channel arrays were designed and fabricated and achieved a Full Width Half Maximum (FWHM) as low as 176 eV at 5.9 keV with peaking time of 1 μs at -13°C. The sensor design, simulation, fabrication, its readout system, and its spectroscopic performance are reported.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Polariton creation in coupled cavity arrays with spectrally disordered emitters

Abstract Integrated photonics has been a promising platform for analog quantum simulation of condensed matter phenomena in strongly correlated systems. To that end, we explore the implementation of all-photonic quantum simulators in coupled cavity arrays with integrated ensembles of spectrally disordered emitters. Our model is reflective of color center ensembles integrated into photonic crystal cavity arrays. Using the Quantum Master equation and the Effective Hamiltonian approaches, we study energy band formation and wavefunction properties in the open quantum Tavis–Cummings–Hubbard framework. We find conditions for polariton creation and (de)localization under experimentally relevant values of disorder in emitter frequencies, cavity resonance frequencies, and emitter-cavity coupling rates. To quantify these properties, we introduce two metrics, the polaritonic and nodal participation ratios, that characterize the light-matter hybridization and the node delocalization of the wavefunction, respectively. These new metrics combined with the Effective Hamiltonian approach prove to be a powerful toolbox for cavity quantum electrodynamical engineering of solid-state systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Coupled surface plasmon–phonon polariton nanocavity arrays for enhanced mid-infrared absorption

Abstract Resonant optical cavities are essential components in mid-infrared applications. However, typical film-type cavities require multilayer stacks with a micron-thick spacer due to mid-infrared wavelengths, and their performance is limited by narrow frequency tunability and angular sensitivity. We propose and experimentally demonstrate the subwavelength-scale (≈ λ 0 /150) resonant nanocavity arrays that enhance the absorption spectrum of the device in the mid-infrared (10–12 microns) via excitation of coupled surface plasmon–phonon polaritons. The proposed metal–insulator–polar dielectric (gold–silicon–silicon carbide) structure supports a guided mode of the coupled surface polaritons in the lateral direction while vertically confining the mid-infrared wave within the 80 nm thick dielectric spacer. In particular, the subwavelength-scale (≈ λ 0 /10) gratings are imposed to form Fabry–Pérot cavity arrays displaying angle-insensitive and frequency-tunable absorption of up to 80% of the optical power in the mid-infrared. Our work should benefit diverse mid-infrared applications and novel designs of polariton-based photonic devices.

42 ENGINEERING↗
DOE OSTI2021

Using the “Inner” Array Boundary with KENO-VI [Slides]

Topics include: SGGP Array definition basics, what is meant by the "Inner" Boundary of an array, a critical experiment with flux filter, and NRC verification of criticality calculations with UNF-ST&DARDS.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

PARA: A New Platform for the Rapid Assembly of gRNA Arrays for Multiplexed CRISPR Technologies

Multiplexed CRISPR technologies have great potential for pathway engineering and genome editing. However, their applications are constrained by complex, laborious and time-consuming cloning steps. In this research, we developed a novel method, PARA, which allows for the one-step assembly of multiple guide RNAs (gRNAs) into a CRISPR vector with up to 18 gRNAs. Here, we demonstrate that PARA is capable of the efficient assembly of transfer RNA/Csy4/ribozyme-based gRNA arrays. To aid in this process and to streamline vector construction, we developed a user-friendly PARAweb tool for designing PCR primers and component DNA parts and simulating assembled gRNA arrays and vector sequences.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Large‐Scale 2D Perovskite Nanocrystals Photodetector Array via Ultrasonic Spray Synthesis

Abstract 2D perovskite (PVSK) single crystals have received significant attention due to their unique optical and optoelectronic properties. However, current synthesis methods face limitations, particularly in large‐area fabrication, which remain critical barriers to practical applications. In this study, the synthesis of red/green/purple‐blue‐colored 2D PVSK nanocrystals over a large area (4‐inch wafer) and the fabrication of high‐performance photodetector arrays are presented via a facile yet efficient spray‐coating approach with a liquid‐bridge transport effect. The photodetector array achieves 100% working yield, high photo‐responsivity (1.5 × 10 6 A W −1 ) and specific‐detectivity (1.1 × 10 16 Jones) with competitive photomapping characteristics. An intelligent vision system for automatic shape recognition is further demonstrated with a recognition rate exceeding 90%. This study provides significant advances in the scalable synthesis of nanoscale 2D PVSK crystals, their integration into large‐area optoelectronic devices, and their potential use in artificial‐intelligence systems.

Lee, Yoon Ho [Davidson School of Chemical Engineer↗
DOE OSTI2021

Facilitating Large‐Scale Snow Shedding from In‐Field Solar Arrays using Icephobic Surfaces with Low‐Interfacial Toughness

Abstract Large‐scale accrual of snow and ice on solar arrays in northern latitudes can cause significant power generation losses during winter. Depending on environmental conditions, snow can encompass a wide range in physical characteristics from dry snow (modulus ≈100 kPa and density ≈0.1 g cm −3 ) to bulk ice (modulus ≈8 GPa and density ≈0.9 g cm −3 ). This variation in snow morphology has made the development of a passive, broad‐spectrum, snow and ice‐shedding surface challenging. Here, the authors develop one of the first surfaces that simultaneously possesses both low‐interfacial strength ( τ˄ ice < 50 kPa) and toughness (Γ ice < 0.5 J m −2 ) with ice. These surfaces, fabricated via the addition of mobile polymer chains/oils to a thin polymeric coating, require extremely low detachment forces for ice, enabling its passive shedding at virtually any accretion length scale. Preliminary evidence that the new surfaces can shed different forms of snow and ice from field‐deployed solar arrays, over a range of subzero temperatures for several weeks, leading to significant increases in power generation is provided. The optically transparent surfaces are easily scalable and can be widely deployed by the solar industry in areas that see persistent snow. Other applications include automotive windshields, LIDAR covers for autonomous vehicles, and cold climate optical sensors.

Dhyani, Abhishek↗
DOE OSTI2026

Toward Fully Soft and Multifunctional Shape Sensing via Optical Waveguide Arrays

For soft bodies, surface deformation and pressure provide proprioceptive and exteroceptive information, including body configuration, body compliance, and external forces. We develop a sheet sensor with a fully soft sensing surface that provides surface shape reconstruction using optical waveguide arrays. The waveguides are fabricated to achieve a tunable linear response to bi‐directional bending curvature, and the waveguide arrays are configured to differentiate between ambiguous shapes. We characterize the waveguide performance, relating curvature sensitivity to the core's surface roughness. Synergy of waveguide responses reduces the number of sensing elements required and achieves damage resilience. Using waveguide sensitivity to pressure, we also demonstrate feasibility for exteroception. We demonstrate the multifunctional sensing capability by wrapping the sheet around an upper arm, showcasing joint motion and external force sensing. Integrated into or applied onto surfaces of robotic or living systems, this design can be implemented in applications such as virtual reality, teleoperation, physical therapy, and soft robotics.

Yu, Qifan [Department of Mechanical Engineering Ma↗
DOE OSTI2020

Atomically Dispersed Nickel(I) on an Alloy‐Encapsulated Nitrogen‐Doped Carbon Nanotube Array for High‐Performance Electrochemical CO 2 Reduction Reaction

Abstract Single‐atom catalysts (SACs) show great promise for electrochemical CO 2 reduction reaction (CRR), but the low density of active sites and the poor electrical conduction and mass transport of the single‐atom electrode greatly limit their performance. Herein, we prepared a nickel single‐atom electrode consisting of isolated, high‐density and low‐valent nickel(I) sites anchored on a self‐standing N‐doped carbon nanotube array with nickel–copper alloy encapsulation on a carbon‐fiber paper. The combination of single‐atom nickel(I) sites and self‐standing array structure gives rise to an excellent electrocatalytic CO 2 reduction performance. The introduction of copper tunes the d‐band electron configuration and enhances the adsorption of hydrogen, which impedes the hydrogen evolution reaction. The single‐nickel‐atom electrode exhibits a specific current density of −32.87 mA cm −2 and turnover frequency of 1962 h −1 at a mild overpotential of 620 mV for CO formation with 97 % Faradic efficiency.

Zhang, Tianyu↗
DOE OSTI2022

Grassland productivity responds unexpectedly to dynamic light and soil water environments induced by photovoltaic arrays

Abstract Agrivoltaic (AV) systems are designed to coproduce photovoltaic (PV) energy on lands simultaneously supporting agriculture (food/forage production). PV infrastructure in agroecosystems alters resources critical for plant growth, and water‐limited agroecosystems such as grasslands are likely to be particularly sensitive to the unique spatial and temporal patterns of incident sunlight and soil water inherent within AV systems. However, the impact of resource alteration on forage production, the primary ecosystem service from managed grasslands, is poorly resolved. Here, we evaluated seasonal patterns of soil moisture (SM) and diurnal variation in incident sunlight (photosynthetic photon flux density [PPFD]) in a single‐axis‐tracking AV system established in a formerly managed semiarid C 3 grassland in Colorado. Our goals were to (1) quantify dynamic patterns of PPFD and SM within a 1.2 MW PV array in a perennial grassland, and (2) determine how aboveground net primary production (ANPP) and photosynthetic parameters responded to the resource patterns created by the PV array. We hypothesized that spatial variability in ANPP would be strongly related to SM patterns, typical of most grasslands. We measured significant reductions in ANPP directly beneath PV panels, where SM and PPFD were both low. However, in locations with significantly increased SM from the shedding and redistribution of precipitation by PV panels, ANPP was not increased. Instead, ANPP was greatest in locations where plants were shaded in the afternoon but received high levels of PPFD in the morning hours, when air temperatures and vapor pressure deficits were relatively low. Thus, contrary to expectations, we found relatively weak relationships between SM and ANPP despite significant spatial variability in both. Further, there was little evidence that light‐saturated photosynthesis ( A sat ) and quantum yield of CO 2 assimilation (ϕCO 2 ) differed for plants growing directly beneath (lowest PPFD) versus between (highest PPFD) PV panels. Overall, the AV system established in this semiarid managed grassland did not alter patterns of ANPP in ways predictable from past studies of controls of ANPP in open grasslands. However, our results suggest that the diurnal timing of low versus high periods of PPFD incident on plants is an important determinant of productivity patterns in grasslands.

14 SOLAR ENERGY↗
DOE OSTI2020

Enhancement of Magneto‐Mechanical Actuation of Micropillar Arrays by Anisotropic Stress Distribution

Abstract Magnetically active shape‐reconfigurable microarrays undergo programmed actuation according to the arrangement of magnetic dipoles within the structures, achieving complex twisting and bending deformations. Cylindrical micropillars have been widely used to date, whose circular cross‐sections lead to identical actuation regardless of the actuating direction. In this study, micropillars with triangular or rectangular cross‐sections are designed and fabricated to introduce preferential actuation directions and explore the limits of their actuation. Using such structures, controlled liquid wetting is demonstrated on micropillar surfaces. Liquid droplets pinned on magnetic micropillar arrays undergo directional spreading when the pillars are actuated as depinning of the droplets is enabled only in certain directions. The enhanced deformation due to direction dependent magneto‐mechanical actuation suggests that micropillar arrays can be fundamentally tailored to possess application specific responses and opens up opportunities to exploit more complex designs such as micropillars with polygonal cross sections. Such tunable wetting of liquids on microarray surfaces has potential to improve printing technologies via contactless reconfiguration of stamp geometry by magnetic field manipulation.

Park, Jeong Eun↗
DOE OSTI2020

Particle Response of Antenna-Coupled TES Arrays: Results from SPIDER and the Laboratory

Future mm-wave and sub-mm space missions will employ large arrays of multiplexed transition-edge-sensor (TES) bolometers. Such instruments must contend with the high flux of cosmic rays beyond our atmosphere that induce ‘glitches’ in bolometer data, which posed a challenge to data analysis from the Planck bolometers. Future instruments will face the additional challenges of shared substrate wafers and multiplexed readout wiring. Here, we explore the susceptibility of modern TES arrays to the cosmic ray environment of space using two data sets: the 2015 long-duration balloon flight of the SPIDER cosmic microwave background polarimeter, and a laboratory exposure of SPIDER flight hardware to radioactive sources. We find manageable glitch rates and short glitch durations, leading to minimal effect on SPIDER analysis. We constrain energy propagation within the substrate through a study of multi-detector coincidences and give a preliminary look at pulse shapes in laboratory data.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Design of the SPT-SLIM Focal Plane: A Spectroscopic Imaging Array for the South Pole Telescope

The Summertime Line Intensity Mapper (SLIM) is a mm-wave line-intensity mapping (mm-LIM) experiment for the South Pole Telescope (SPT). The goal of SPT-SLIM is to serve as a technical and scientific pathfinder for the demonstration of the suitability and in-field performance of multi-pixel superconducting filterbank spectrometers for future mm-LIM experiments. Scheduled to deploy in the 2023-24 austral summer, the SPT-SLIM focal plane will include 18 dual-polarisation pixels, each coupled to an $R = \lambda / \Delta \lambda = 300$ thin-film microstrip filterbank spectrometer that spans the 2 mm atmospheric window (120–180 GHz). Each individual spectral channel feeds a microstrip-coupled lumped-element kinetic inductance detector, which provides the highly multiplexed readout for the 10k detectors needed for SPT-SLIM. Here, we present an overview of the preliminary design of key aspects of the SPT-SLIM focal plane array, a description of the detector architecture and predicted performance, and initial test results that will be used to inform the final design of the SPT-SLIM spectrometer array.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Hydrodynamic characterization of the coastal pioneer array ocean observing system

Ocean observation buoys require relatively small amounts of power, yet traditionally necessitate costly resupply trips for battery replacement. With the offshore location of the buoys and small power requirements, wave energy may be an effective solution for providing consistent and reliable power to support the buoy instrumentation. The US National Science Foundation Ocean Observatories Initiative (OOI) includes arrays of point absorber-like buoy systems used for ocean observation that have been deployed at multiple locations including the Southern Mid-Atlantic Bight. A study is currently underway to design a pitch resonator wave energy converter to supplement existing renewable energy generation for powering observation instrumentation. This paper details field measurements from surface moorings of the OOI Coastal Pioneer Array, which informs the subsequent development of a numerical model for the moored observation system. The model is developed in Wave Energy Converter Simulator (WEC-Sim), which leverages the Simscape multibody solver within the MATLAB/Simulink framework and linear potential flow theory to simulate the hydrodynamic interactions and multibody dynamics in 6 degrees of freedom. Multiple tuning variables are considered to produce a model for the system that matches well with empirical data (about 8% error). In conclusion, the WEC-Sim model will serve as a platform for integrating the pitch resonator wave energy converter concept and deployment preparation (detailed design including power take-off and control systems, response evaluation, etc.).

hydrodynamic modeling↗
DOE OSTI2024

Optimization-Inspired Pin-Fin Array for Supercritical Carbon Dioxide Recuperator

Additively manufactured heat exchangers are one possible route to cost-effective sCO 2 power cycles. In this paper, experimental results are obtained for two helical pin fin tubes that were designed following parametric optimization of the fin array. Neither the numerical optimization nor the experimental testing have been previously reported in the literature. The two tube designs were, (1) the optimization inspired design, and (2) the optimization-inspired design with a fin diameter increased by a factor of 2. To characterize the print, the designs were scanned using X-ray computed tomography to measure feature sizes and heat transfer area. The optimization was conducted in a commercial, computational fluid dynamics code. The code solved the Reynolds Averaged Navier-Stokes (RANS) and energy equations with turbulence closure provided by the shear stress transport (SST) k-ω model. In the experiments, the Nusselt number augmentation was measured using the Wilson plot technique and the friction factor was determined with mass flow and pressure drop measurements. The experimental testing indicated that the optimization-inspired design had a friction factor that was four times less than the baseline tube design at equal Nusselt number. Additionally, the optimization-inspired design had a 14% improvement in Nusselt number, at equal friction factor, relative to the best performing computational fluid dynamics (CFD) trial points. Tube design (2), with the larger diameter pin fins, had similar performance, within experimental error, as the tube with the smaller diameter pin fins (1). Both tubes achieved overall fin array efficiencies near 1. A performance factor, V/V 0 , equal to the volume of the enhanced heat exchanger divided by the volume of the baseline (no-fins) heat exchanger, is recommended to quantify internal cooling performance. In conclusion, the experimental shell and tube heat exchanger, using the additively manufactured tube, is competitive with printed circuit heat exchangers in its pressure drop class and could be further improved by optimizing a shell-and-tube heat exchanger utilizing this heat transfer enhancement feature.

42 ENGINEERING↗
DOE OSTI2024

On the computation of moments in the Super-Transition-Arrays model for radiative opacity calculations

In the Super-Transition-Array statistical method for the computation of radiative opacity of hot dense matter, the moments of the absorption or emission features involve partition functions with reduced degeneracies, occurring through the calculation of averages of products of subshell populations. Here, in the present work, we discuss several aspects of the computation of such peculiar partition functions, insisting on the precautions that must be taken in order to avoid numerical difficulties. In a previous work, we derived a formula for supershell partition functions, which takes the form of a functional of the distribution of energies within the supershell and allows for fast and accurate computations, truncating the number of terms in the expansion. The latter involves coefficients for which we obtained a recursion relation and an explicit formula. We show that such an expansion can be combined with the recurrence relation for shifted partition functions. We also propose, neglecting the effect of fine structure as a first step, a positive-definite formula for the Super-Transition-Array moments of any order, providing an insight into the asymmetry and sharpness of the latter. The corresponding formulas are free of alternating sums. Several ways to speed up the calculations are also presented.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Comparison of machine learning and electrical resistivity arrays to inverse modeling for locating and characterizing subsurface targets

Here, this study evaluates the performance of multiple machine learning (ML) algorithms and electrical resistivity (ER) arrays for inversion with comparison to a conventional Gauss-Newton numerical inversion method. Four different ML models and four arrays were used for the estimation of only six variables for locating and characterizing hypothetical subsurface targets. The combination of dipole-dipole with Multilayer Perceptron Neural Network (MLP-NN) had the highest accuracy. Evaluation showed that both MLP-NN and Gauss-Newton methods performed well for estimating the matrix resistivity while target resistivity accuracy was lower, and MLP-NN produced sharper contrast at target boundaries for the field and hypothetical data. Both methods exhibited comparable target characterization performance, whereas MLP-NN had increased accuracy compared to Gauss-Newton in prediction of target width and height, which was attributed to numerical smoothing present in the Gauss-Newton approach. MLP-NN was also applied to a field dataset acquired at U.S. DOE Hanford site.

54 ENVIRONMENTAL SCIENCES↗