Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced Reactors Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Development of a U-19Pu-10Zr fuel performance benchmark case based on the IFR-1 experiment

Metallic nuclear fuels are subject to research and development for use in advanced reactors. Robust, accurate metallic fuel performance models are important for the design, safety analysis, and licensing of these reactors. However, metallic fuel performance models require additional development; they are not as mature as UO 2 fuel performance models. A benchmark case based on the IFR-1 experiment was developed to better gauge the accuracy of existing models, identify models for high-priority development, and potentially quantify any future improvements made by further model development.This work collected publicly available information on the IFR-1 experiment and used it to develop the benchmark case. Fuel behavior during the IFR-1 irradiation was simulated by using the fuel performance code BISON, and the predicted results were compared with postirradiation examination data from the IFR-1 experiment. Furthermore, a sensitivity study and tuning studies were performed as a preliminary investigation into the causes of inaccurate temperature and dimensional change predictions.The benchmark predicted reasonably accurate values for the burnup and fission gas release. There was error in the predicted temperatures, which could be explained by uncertainty in the input parameters and legacy temperatures. BISON over-predicted dimensional changes in the fuel and cladding. The sensitivity study showed that the dimensional changes were most sensitive to the fuel swelling anisotropy and the cladding void swelling model. Future benchmark and model development should focus on cladding swelling behaviors to improve dimensional change predictions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

AGR-5/6/7 Ceramography Report

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program was established in 2002 to conduct research and development on tri-structural isotropic (TRISO)-coated particle fuel for High Temperature Gas-cooled Reactors (HTGRs). All AGR irradiations have been completed: AGR-1 (Collin 2015), AGR-2 (Collin 2014), AGR-3/4 (Collin 2016) and AGR-5/6/7 (Pham 2021). The objectives of each program are presented in Figure 1.1. The purpose of the AGR-5/6/7 program was to provide a baseline fuel qualification data set to support licensing, deployment, and operation of HTGRs in the United States. To achieve these goals, the program includes fuel fabrication, irradiations of TRISO fuels and high-temperature materials, safety testing and post-irradiation examination (PIE), fuel performance modeling, and fission product (FP) transport (Sharp 2020). The AGR-5/6/7 work continues as a final irradiation program of the Advanced Reactor Technologies (ART) program, that began in February 2018 and ended in July 2020. The AGR-5/6/7 fuel compacts were irradiated for a total of approximately 360.9 effective full power days (EFPDs) (Stempien 2023), resulting in final burn-up values, on a per-compact basis, ranging from 5.66% to 15.26% fissions per initial heavy metal atom (FIMA), and fast fluence values ranging from 1.62×1025 n/m2 to 5.55×1025 n/m2 (E >0.18 MeV) (Stempien 2022)

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Addendum to Capability Needs for Irradiated and Radioactive Materials Research (Ad Hoc Committee Summary Report)

Nuclear materials and fuels studies are challenging research and engineering targets because of their inherent radioactivity as well as their heterogeneous microstructure. Advanced light sources have made significant underpinning scientific contributions to the understanding of structural and fuel cladding material microstructure and properties and the development of structure-property relationships. These facilities have the potential to help advance the Department of Energy (DOE) Office of Nuclear Energy (DOE-NE) mission priorities providing underpinning understanding of technically important challenges, including: irradiation induced embrittlement and swelling; stress corrosion cracking and corrosion in extreme environments; ageing of reactor pressure vessels steels; nuclear fuel characterization; and nuclear waste form optimization as well as playing a major role in the development of a materials performance matrix to aid in the design of new materials to meet the needs of advanced reactor concepts. However, the delivery of underpinning understanding is the mission of DOE Office of Science (DOE-SC). While filling such knowledge gaps is important, efforts in this direction should not be confused with the strategic technology focused mission goals of DOE-NE to enable the continued operation of existing U.S. nuclear reactors, to enable the deployment of advanced nuclear reactors, to develop advanced nuclear fuel cycles, and to maintain U.S. leadership in nuclear energy technology.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Analysis of Using a Hybrid ZIRCEX Process to Generate High-Assay Low-Enriched Uranium (HALEU) - 20158

Idaho National Lab (INL) is investigating the feasibility of providing High-Assay Low Enriched Uranium (HALEU) by recovering Highly Enriched Uranium (HEU) from spent nuclear fuel (SNF) and downblending the HEU with natural, low-enriched, or depleted uranium (NU, LEU, or DU). That investigation identified that significant quantities of HALEU could be produced with a Hybrid ZIRCEX process to further advanced reactor research while reducing INL's environmental liability. Many new advanced reactor designs are being developed with improved safety, efficiency, and economics. Most require nuclear fuel with U-235 enrichment between 5% and 20%, which is defined as HALEU. Although technically feasible, there is no current domestic capability to make HALEU in the US. While it is anticipated that industry will provide HALEU through commercial enrichment once advanced reactors mature, until a market is established, an interim source of HALEU is needed to enable research and demonstration. An interim source of HALEU could be provided by recovering the HEU in some DOE-managed SNF and downblending it to between 5% and 20% using the Hybrid ZIRCEX Process. ZIRCEX is a dry head-end process to remove cladding (zirconium or aluminum) from SNF. Drying of the SNF is needed prior to introduction to ZIRCEX. After cladding removal, uranium and fission products in the bed material are oxidized and elutriated. In a Hybrid ZIRCEX process, the HEU process stream is sent to a very compact, modular solvent extraction process for uranium purification. The uranyl nitrate from solvent extraction is denitrated and calcined to produce a HALEU product ready for fuel fabrication. The long-lived fission products from solvent extraction are immobilized in glass using a small in-can melt. By removing the cladding before dissolution, the volume of glass waste is reduced by a factor of up to 300 times (when compared to not removing the cladding from the fuel). Other radioactive wastes from the process could be disposed of as Class A or Class B low-level waste. In addition to producing HALEU for advanced reactors, consumption of SNF would reduce DoE's environmental liability. Incorporating low-enriched spent fuel (versus exclusive use of LEU, DU, or NU) into the downblending scheme could reduce the SNF inventory even further. Several downblending and enrichment scenarios using INL fuels were investigated in this study. The results of this analysis show that the Hybrid ZIRCEX process could make a significant contribution to needed HALEU feedstock and reduce the environmental liability of managing SNF at INL. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Fuel Performance Modeling Plan to Support the Advance Gas Reactor Program

This report documents the current status of the fuel performance modeling initiative to support the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program in the development of tristructural-isotropic-coated fuel particles. It includes a brief summary of the codes that have been developed to support tristructural isotropic modeling along with a summary of the behavior of fuel particles during irradiation and the modeling used to capture these effects. In addition, this report identifies further modeling and material property needs for further development based on experience from previously performed AGR experiments. In general, the remaining activities to support fuel performance modeling for the AGR program include continued AGR experiment support for AGR-3/4 and AGR-5/6/7 as well as modeling improvements identified throughout the course of the program. These modeling improvements can be summarized as thermomechanical particle behavior and fission product transport. Additional modeling needs may be identified while processing the data collected during the AGR post-irradiation examination campaign and may lead to further improvements that are not included in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Insulation Activation and Contamination in Low-Power Experiments

Among the diverse advanced nuclear reactor concepts being developed are designs that expect to operate at much higher temperatures than conventional light-water reactors, and therefore require alternative materials for components capable of withstanding these extreme temperatures. Insulation is one such component where alternative high-temperature industrial composites are being considered. Low-power experiments can provide an opportunity for advancing our understanding of material behavior under irradiation; however, these experiments are not without occupational hazards. The focus of this paper is the potential for activation of insulating composites when exposed to neutron fluence during reactor experiments, and to discuss the subsequent contamination of the testing area. This paper will also discuss practical measures for preventing the creation and inhalation of activated particulate matter (i.e., dust), such as engineering and administrative controls and personal protective equipment. This paper evaluates the suitability of several insulation materials for use in reactor experiments based on their activation from neutron irradiation. The materials considered are Pyrogel XTE by Aspen Aerogel, Cerablanket and Kaowool by Morgan Advanced Materials, Thermo-12 Gold by Johns Manville, and Maxsil CF6-2000 by McAllister Mills. Although these materials are not yet widely used in the nuclear industry, they are common in other industries due to their thermal insulating properties. These materials produce dust while handling that can pose health and safety hazards, which could be further exacerbated by activation. The analysis presented in this paper utilizes a deterministic method developed to predict the activation source term of the provided insulation materials. The method calculates the atomic density of each element within the composites and simulates their exposure to a specified neutron flux density representative of low power experimental conditions. During the irradiation phase and throughout the extensive cooling period, neutron absorptions and nuclear decays are tracked for relevant isotopes. The residual activity within each composite is then assessed to identify the material with the lowest potential radiological hazard to workers. Dust will be created during installation and removal of insulating materials and may also be generated during the experiment. Contamination of surrounding surfaces due to dispersion is highly likely unless preventative measures are taken. The results of this analysis are used to estimate an internal dose from inhalation of activated dust, which is significantly lower than the allowable whole-body dose. However, the risk of internal exposure may increase if the dust becomes a transport vector for nuclear material. The goals of this paper are to enhance the understanding of the potential activation and contamination hazards from the use of these insulating materials in low-power nuclear experiments and to foster safer work environments through informed decision-making and strategic planning. This work ultimately contributes to a broader understanding of how new non-nuclear materials for advanced reactors impact the radiological safety of co-located workers, helping to ensure the responsible management of radioactive materials during installation and decommissioning activities.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗
DOE OSTI2023

AGR-5/6/7 Irradiation Disassembly and Metrology First Look

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program was established to perform research and development on tristructural isotropic (TRISO)-coated particle fuel to support deployment of high-temperature gas-cooled reactors (HTGRs), which are graphite-moderated nuclear reactors cooled with helium. This work continues as part of the Advanced Reactor Technologies (ART) TRISO Fuel Program. The overarching program goal is to provide a baseline fuel qualification data set to support licensing, deployment, and operation of HTGRs in the United States. To achieve these goals, the program includes fuel fabrication, irradiations of TRISO fuels and high-temperature materials (e.g., graphite), safety testing and post-irradiation examination (PIE), fuel performance modeling, and fission product transport and source term determination. The ART AGR program has conducted four distinct fuel irradiation experiments in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). The first of these irradiation tests, designated AGR-1, began in ATR in December of 2006 and ended in November 2009. This experiment was primarily to act as a shakedown test of the multi-capsule test train design and to provide early data on fuel performance that would be used in fuel fabrication process development. AGR-1 fuel kernels were produced on an engineering scale, but the TRISO coatings and cylindrical fuel compacts were fabricated on a laboratory scale. The AGR-1 PIE was completed and the final report was published in 2015. The second irradiation test, AGR-2, started in ATR in June 2010 and ended in October 2013. The AGR-2 irradiation test was designed to provide fuel performance data for coated particles fabricated on an engineering-scale pilot line using a coater with an internal chamber diameter of 150 mm (6 in.). The final PIE report was published in 2021. AGR-3/4, a single irradiation that combined what were originally conceived as the third and fourth tests, was to support the refinement of fission product transport models and to assess the effects of sweep gas impurities on fuel performance and fission product transport. PIE of the AGR-3/4 experiment is still in progress as of this writing. The subject of this report is AGR-5/6/7, the final qualification test of AGR TRISO fuel made entirely at the engineering scale.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Electrodialysis: An effective methodology to purify the leachate of spent Li-ion batteries

The electrification of transportation and the transition of society towards low or net-zero carbon emissions has led to a skyrocketing global demand for Li-ion batteries. After a service life of three to ten years, Li-ion batteries have less than 80 % of their initial capacities and draw near to the end of their lives for practical utilization. Due to potential supply chain shortages and the value embodied in Li-ion batteries, it is imperative to recycle them, to recover the materials, and to improve the circularity and the sustinability of the industry. How to cost-effectively purify spent batteries while reducing time, energy, and waste emissions is a challenge faced by Li-ion battery recyclers. The first electrochemical membrane reactor reported in our group hasa high selectivity towards lower Cu 2+ , Al 3+ and Fe 3+ ions (<5 ppm) and retains >95% of the Ni 2+ , Co 2+ and Mn 2+ ions in the leachate. An advanced electrochemical membrane reactor was developed in this study. Further, not only does the new reactor have the same selectivity as the original reactor, but other advantages including a faster leachate processing rate (up to 10X faster). The advanced reactor can also directly generate acid at the anode side; eliminating the reactor restoration step. The prominent advantages that this electrodialysis technology has over chemical-precipitation methods include: (1) ion recovery efficiencies do not diminish after removing the impurities, Ni 2+ , Co 2+ and Mn 2+ , even at a higher initial Ni 2+ ion concentrations; in comparison, chemical precipitation has Ni 2+ , Co 2+ and Mn 2+ ion recovery efficiencies reduced significantly when the initial Ni 2+ , Co 2+ and Mn 2+ ion concentrations increase. (2) electrodialysis does not change the concentrations of Ni 2+ , Co 2+ and Mn 2+ ions significantly, but chemical precipitation could reduce Ni 2+ and Co 2+ ions to less than half of their initial values. Through electro-dialyzing the leachate, the H 2 evolution reaction mechanism was found to switch from the Volmer-acid Heyrovsky mechanism to the Volmer-alkaline Heyrovsky mechanism at a pH of around 3.7.

25 ENERGY STORAGE↗
DOE OSTI2020

Effects of Neutron Irradiation on the Micro/Nano Scale Structure and Fission Product Distribution of TRISO Coated Particle Fuel Kernels from AGR Experiments

The Advanced Reactor Technologies (ART) Program at Idaho National Laboratory (INL) includes the Advanced Gas Reactor (AGR) fuel development and qualification program that consists of fuel fabrication, experiment irradiations, post-irradiation examination (PIE) and safety testing to assess tristructural isotropic (TRISO) fuel performance during normal irradiation and under potential accident conditions. Advanced microscopy work on selected AGR-1 and AGR-2 unirradiated and irradiated fuel specimens is performed as part of the PIE effort. PIE work on fuel from the first experiment irradiation, AGR-1, began at INL in April 2010, and AGR-2 PIE began at INL in July 2014. This work scope includes University of Florida (UF) performing advanced electron microscopy examination and analysis using facilities at the Center for Advanced Energy Studies (CAES), INL or UF’s electron microscopy facilities. Electron microscopic examination and analysis may include scanning transmission electron microscopy (STEM), transmission electron microscopy (TEM), selected area diffraction (SAD), electron energy loss spectroscopy (EELS), electron dispersive spectroscopy (EDS) and atom probe tomography (APT) on the fuel kernels of TRISO-coated fuel particles. The electron microscopy lamellae will be provided by INL and will be available at CAES or Irradiated Materials Characterization Laboratory (IMCL).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Development of Conceptual Lead Cartridge Design to Perform Irradiation Experiments in VTR

This paper seeks to introduce the latest design of the Extended Length Test Assembly–Cartridge Lead (ELTA-CL) with associated thermal-hydraulic (TH) assessment and related experiment activities to support the critical component development performed by the ELTA-CL team (Los Alamos National Laboratory, Westinghouse Electric Company, and the University of New Mexico). The goal of the ELTA-CL program is to develop and validate an experimental capability to perform irradiation experiments in the Versatile Test Reactor (VTR) addressing Lead Fast Reactor (LFR) technology gaps, in support of the commercial development of advanced lead-cooled fast reactor concepts. Through a design maturation process and parametric study, a conceptual design is proposed to meet the requirements for material and corrosion testing. Thermal-hydraulic characteristics for the conceptual design at desired operating conditions are assessed with systems-level (one-dimensional) and computational fluid dynamics (three-dimensional) simulations. Along with the conceptual design work, experimental activities for the development of critical components such as the pump and flowmeter are undertaken. From both the modeling study and the experimental results, the design requirements of the Phase 1 ELTA-CL (e.g., 500°C and 2 m/s) are achievable with the current conceptual design. Additional design improvements and safety assessments at both steady-state and transient conditions for the final ELTA-CL design will be pursued.

42 ENGINEERING↗
DOE OSTI2023

Collaborative Study on Weldability of Irradiated Stainless Steel 304 Materials Removed from The NRU Reactor

A collaborative research on developing advanced welding technologies for irradiated stainless steel 304 materials between CNL and ORNL has been established to support both U.S. and Canadian interests in evaluation of weld repair techniques on irradiated materials to support continuous operation of commercial nuclear power. The work utilizes unique material from the National Research Universal (NRU) reactor and the specialized welding hot cell facility at ORNL. The objective is to explore suitable welding technique and parameters and to determine the helium concentration limitation in terms of irradiated stainless-steel weldability. An additional objective is to develop the knowledge and understanding of cracking mechanisms induced by high concentration of helium in the process of weld repair of the irradiated structural alloys. This report summarizes the experimental welding evaluation on irradiated material from the NRU reactor containing helium concentrations ranging from 12 to 45 atomic parts per million (appm).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Release of a High Temperature Engineering Test Reactor (HTTR) Steady State Multiphysics Model to the Virtual Test Bed

In response to climate change, global governments and private industry have established a common goal of achieving net-zero emissions by 2050 \cite{osti_1865910}. This goal requires a reassessment of current energy demands and production methods. Reducing emissions at an affordable cost while maintaining grid reliability requires a nationwide collaborative effort among government and industry in the United States. Nuclear power is the leading low-carbon electricity generation method. In the past 50 years, the use of nuclear power has reduced carbon dioxide emissions by over 60 gigatons and has played a crucial role in the security of energy supply~\cite{IEA}. In the U.S., nuclear power accounts for 20\% of the electrical supply and provides energy reliably. Advanced reactors will operate at higher temperatures, operate more efficiently, utilize more energy stored within fuel, and reduce the amount of waste produced \cite{osti_1616270}. To face these challenges and goals, the U.S. Department of Energy has created an initiative to focus on the modeling and simulation tools to support future nuclear power plant design, licensing, and operations. The Virtual Test Bed (VTB)~\cite{vtb2023} was launched by the National Reactor Innovation Center (NRIC) in collaboration with the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program to support the advanced nuclear reactor community. The VTB involves teams from both Idaho National Laboratory and Argonne National Laboratory and aims to provide example models for a broad range of both current and future advanced reactor designs. A feature of the VTB is the automatic testing of these models to ensure continued functionality as simulation tools are further developed. The VTB and the advanced reactor models documented there are important resources for this initiative. This work describes the inclusion of a new model on the VTB---a High Temperature Engineering Test Reactor (HTTR) steady-state model \cite{LABOURE2023109838}.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

FY20 Progress Report on FIPD Development and User Support

The DOE Advanced Reactor Technologies program has supported efforts to recover and preserve metallic fuel data generated throughout the past fast reactor R&D programs. Those efforts have focused on establishing databases for information from the experiments conducted during the Integral Fast Reactor program including data generated at EBR-II, FFTF, and TREAT reactors, as well as out of pile transient testing data. These databases are essential for future-licensing activities of metallic fuel based advanced fast reactors. This report describes the EBR-II Fuels Irradiation & Physics Database (FIPD) development, content updates, and user support during the current fiscal year (FY20). Future plans are also provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

The Fast Modular Reactor (FMR) Pre-Application Regulatory Engagement Plan

The Fast Modular Reactor (FMR) is a 50 MWe Gascooled Fast Reactor (GFR) being developed by General Atomics Electromagnetic Systems (GA-EMS) under U.S. Department of Energy’s (DOE’s) Advanced Reactor Demonstration Program (ARDP), specifically Advanced Reactor Concepts 2020 (ARC-20). The 3-year conceptual design of the FMR is being conducted with verifications of key metrics in fuel, safety, and operational performance. GAEMS is pursuing design, licensing, and commercialization of the proposed reactor, with demonstration by 2030 and deployment by the mid-2030s. The U.S. Nuclear Regulatory Commission (NRC) recommends the pre-application regulatory engagement to provide for early identification of regulatory requirements for advanced reactors and to provide all interested parties with a timely, independent assessment of the safety and security characteristics of advanced reactor designs. As such, GAEMS is developing a pre-application regulatory engagement plan (REP) of the FMR.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

A Metallic Fuel Performance Benchmark Problem Based on the IFR-1 Experiment

Metallic nuclear fuels are an active area of research and development for use in advanced reactors. Robust and accurate metallic fuel performance models are necessary for the design, safety analysis, and licensing of such reactors. However, metallic fuel performance models are not as mature as ceramic fuel performance models and require additional development. In order to better gauge the accuracy of existing models, identify high-priority models for development, and quantify the improvements made by future model development, ORNL has developed a benchmark problem based on the IFR-1 experiment. This work gathers all relevant information on the IFR-1 experiment and uses it to develop the benchmark problem. It simulates the problem using the fuel performance code BISON and compare the results to post-irradiation examination data from the experiment. Then a sensitivity analysis is performed on the BISON model to determine the benchmark problem’s sensitivity to uncertainty in the input parameters. The results suggest that BISON’s mechanical models require additional development. Plastic deformation is under-predicted in the cladding and axial swelling is over-predicted in the fuel. These problems may be related. Additionally, there is a bias in the temperature which may be a result of uncertainty in the input parameters rather than an issue with the fuel performance models.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

SAM Developments for MSR Modeling (FY21)

An advanced system analysis tool, SAM, is under development for advanced non-LWR reactor safety analysis, including molten salt reactors (MSR). To support the development and utilization of the SAM code for MSR safety analysis and licensing, continuous efforts have been devoted to enhancing code capabilities and updating reference models for the MSRs. This report documents the FY21 progress in SAM code development, capability enhancements, and reference model development to support transient safety analysis of MSRs, including code enhancements in reactor kinetics and reactivity feedback modeling for liquid fuel reactors, updates of the Molten Salt Reactor Experiment (MSRE) primary system model, developments and updates of the molten salt fast reactor (MSFR) model based on EVOL design, and implementation of a drift flux model for modeling gas transport in MSR systems.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Important Human Actions for Advanced Reactors: Implications for Human Factors

As advanced reactor platforms continue to develop and gain traction in the energy sector there is a need for risk-informed, scalable regulations that match that progress. This is a core component of the U.S. Nuclear Regulatory Commission’s proposed Part 53 Rule Making; the Accelerating Deployment of Versatile, Advanced Nuclear for Clean Energy (ADVANCE) Act; and other efforts that seek to update nuclear power regulations. This paper covers one key aspect of that regulatory evolution: Important Human Actions (IHA). In this paper, we discuss how the understanding and definitions of IHAs have changed and what that means for human factors engagement through the process of developing these technologies. Instead of a narrow focus on control actions that led to an increase in core damage risk, the new focus is on IHAs is “wherever they occur.” What this means is that having a highly automated or passive safety system does not eliminate IHAs. Rather, it shifts the focus point to all the actions that enable these systems. Everything from maintenance, to design, to training can be considered an IHA and that dramatically shifts the efforts and level of engagement necessary for human factors to enable these technologies. We discuss the notions of risk-informed human factors that underpin these efforts, give several examples, and briefly describe the risk assessment methodologies that will be needed. In the past, IHAs were identified and then became a focus point of human factors engineering (HFE) activities to ensure a robust evaluation of the task was completed. The future is less clear. HFE for nuclear energy will need to evolve and become more integrated in technology development than ever before.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

AGR TRISO Fuel Performance Modeling in FY-25

This report summarizes the activities performed in FY-25 to support fuel performance modeling for the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program. This includes implementation of a new uranium oxycarbide (UCO) kernel swelling rate model, inner pyrolytic carbon (IPyC) cracking behavior and failure predictions, development of new UCO and silicon carbide (SiC) cesium diffusion parameters, and the thermomechanical behavior of particle layers using experimental data from micro-tensile strength testing.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗